Voxx Accessories PNMW01 Baby Monitor-Parent Unit User Manual

Voxx Accessories Corp. Baby Monitor-Parent Unit

User Manual

Video Baby Monitor Systemwith 1.5” Mini MonitorUser GuideWhat’s insideWelcome! ................................................................ 2Getting started ...................................................... 3Tour of the system ............................................... 7Everyday use .........................................................13Cameras ...................................................... 14Motion/Alerts ............................................ 18Recording ................................................... 21Playing Back Pictures and Videos ......22Sleep Mode ................................................23Lullabies ..................................................... 24Contrast ......................................................25Settings ...................................................... 26Troubleshooting / FAQs ..................................28
Getting Started2Step 1: UnpackWELCOME!This baby monitoring system makes it simple to keep your eyes and ears on your little one! This guide takes you through the steps to get started!See our setup videosGo to ProjectNursery.com/Electronics or scan the QR code here.Before you start...Make sure you read the Important Information sheet included in this package.Wireless camera Parent monitorMini monitorThe accessories:(2) 10-foot charging cables(1) 3-foot charging cable (for the mini monitor)(1) dual power adapter (for the monitors)(1) single power adapter (for the camera)(1) wristband (1) lanyard (1) carabiner(1) clipNote: Micro SD card included in model PNM5W01S.
Getting Started3GETTING STARTEDFind the short charging cable included in this package.Plug one end of this cable into the USB CHARGING jack on the side of the mini monitor.Find one of the long charging cables included in this package.Plug one end of this cable into the USB CHARGING jack on the side of the parent monitor. Plug the other ends of the charging cables into the double charging adapter. Then plug the adapter into an outlet or surge protector.Step 2: Charge the monitorsFind a location for the camera that gives you the best view of your baby in his or her crib.Place the camera on a flat surface, like a dresser or shelf, or mount the camera to a wall using the keyhole slots on its bottom.IMPORTANT: NEVER place the camera or cords of any kind inside the crib. NEVER place the camera or cords within reach of the baby.Step 3: Position the camera WARNING Strangulation Hazard: Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3ft (0.9m) away). Never use extension cords with AC Adapters. Only use the AC Adapters provided.
Getting Started4Find the other long charging cable included in this package.Plug one end into the DC In jack on the back of the camera. Plug the other end into the single charging adapter. Then plug the adapter into an outlet or surge protector.The camera turns on automatically when it’s plugged in (the indicator light on the base below the camera lens turns blue).Step 4: Plug in the cameraPress and hold the POWER button on the parent monitor to turn it on.Press and hold the POWER button on the top of the mini monitor to turn it on.Step 5: Turn everything onCongratulations!Your system is ready to use! The camera comes pre-paired with your parent and mini monitors. However, it’s a good idea to go ahead and set the time on both your parent and mini monitors now, before you start using them.For information on how to use your new system, see the next chapter of this owner’s manual.IMPORTANT!To keep this baby monitoring system as secure as possible, only one monitor can view video at a time. If you want to use the mini monitor, for example, make sure you power the parent monitor off (and vice-versa).
Getting Started512:00AMTemperatureTime SetFactory ResetSupportProduct InformationSD Card InformationDate: 01/01/16Time: 12:00 AMUse the up/down arrow buttons to set the month, day, and year. 4After setting the year, press the right arrow to adjust the time.Use the up/down arrows to set the hours, minutes, and AM/PM. Press OK/ZOOM when you’re finished.Step 6: Set the date and time on the parent monitorUse the arrows to highlight SETTINGS. Press OK/ZOOM to select it. The Settings menu appears on screen.Press the down arrow to highlight Time Set. Press OK/ZOOM to select it. 12:00AMTemperatureTime SetFactory ResetSupportProduct InformationSD Card InformationPress the MENU button on the parent monitor. The menu appears on screen. 12:00AM123512:00AMTemperatureTime SetFactory ResetSupportProduct InformationSD Card InformationDate: 01/01/16Time: 12:00 AM
Getting Started672º 12:00AMTemperature C/FTime SetFactory ResetSupportProduct InformationButton Information72º 12:00AMTemperature C/FTime SetFactory ResetSupportProduct InformationButton Information72º 12:00AMPress the MENU button on the top of the mini monitor.The menu appears on screen. Move the joystick on the front of the mini monitor to the right to highlight the (Settings) icon. Press OK/ZOOM to select it. The Settings menu appears.Move the joystick down to highlight Time Set. Press OK/ZOOM to select it.Use the up/down joystick to set the month, day, and year. After setting the year, press the right joystick to adjust the time. Use the up/down joystick to set the hours, minutes, and AM/PM. Press OK/ZOOM when you’re finished. 1234Step 7: Set the date and time on the mini monitor
Tour of the system7Parent Monitor accesses the system’s menu screens. turns the monitor on and off (press and hold). and turn the volume down/up. In menu screens, these navigate left/right. zooms the camera in/out. Press and hold to start pan/tilt of the camera, then use the arrows to pan and tilt. and navigate up/down in menu screens.SOUND LEVEL indicators show you the level of sound from your baby’s room. lets you talk through the camera’s speaker. Press and hold while talking. turns the screen on and off. Press and hold to switch cameras if you have more than one paired to this monitor.TOUR OF THE SYSTEMWatching babyYou can turn the display on and off without turning the monitor off. You’ll still hear your baby, but the display will be asleep until you awaken it.To turn the display on or off: Press the VIDEO ON/OFF button on the parent monitor.IMPORTANT: To see video on the parent monitor, make sure the mini monitor is powered off.
Tour of the system8Parent monitor side and back panelsMICRO SD slot holds the memory card (included with model PNM5W01S; not included with other models) for video or still image recording.USB CHARGING jack plugs into your charging cable to recharge or power the parent monitor. Built-in easel stand lets you stand the unit on a flat surface.Pan, Tilt, and ZoomTo zoom the active camera: Press the OK/ZOOM button on the parent monitor.To pan or tilt the active camera: Press and hold the OK/ZOOM button until the pan/tilt arrows appear on the screen. Then use the arrow buttons to pan and tilt the camera.Talking to babyTo talk through the speaker on the active camera: Press and hold the TALK button on the parent monitor. Talk normally to the parent monitor while you’re pressing the TALK button—your voice will come out on the camera’s speaker. Release the TALK button when you’re done talking.Built-in easel standListening to babyThe SOUND LEVEL indicators on the parent monitor show you at a glance the sound level in your baby’s room, regardless of how loud the audio is on the parent monitor.To increase or decrease the volume of the audio monitor: Press the VOL+ or VOL– buttons on the parent monitor.
Tour of the system9Mini monitorPOWER turns the mini monitor on and off (press and hold).MENU accesses the system’s menu screens.TALK lets you talk through the camera’s speaker. Press and hold while talking.VIDEO turns the screen on and off. Press and hold to switch cameras if you have more than one paired to this monitor.Left/Right arrows navigate left/right in menu screens. OK/ZOOM zooms the camera in/out. Press and hold to start pan/tilt of the camera, then use the arrows to pan and tilt.Up/Down arrows turn the volume down/up. In menu screens, these navigate up/down.USB CHARGING jack (right side) plugs into your charging cable to recharge or power the mini monitor. To turn the display on or off: Press the VIDEO button on the mini monitor.IMPORTANT: To see video on the mini monitor, make sure the parent monitor is powered off.To zoom the active camera: Press the OK/ZOOM button on the mini monitor.To pan or tilt the active camera: Press and hold the OK/ZOOM button until the pan/tilt arrows appear on the screen. Use the arrow buttons to pan and tilt the camera.To talk through the speaker on the active camera: Press and hold the TALK button on the mini monitor, then speak normally while you’re pressing the TALK button. Release the TALK button when you’re done talking.
Tour of the system10Status Bar Indicators shows the strength of the current camera’s signal.Temperature reading shows the temperature in Fahrenheit at the active camera. If you want to change this to Celsius, see page 27 for instructions. shows the camera that the monitor is currently displaying. (parent unit only) indicates that the Low Battery Noise alert is on. This means the monitor gives an audio signal when it needs to be recharged. See page 18 for instructions on turning this on and off. (parent unit only) indicates that Motion Activated Video Alert is on. This means the monitor automatically switches on whenever the camera detects motion. See page 18 for instructions on turning this on and off. (parent unit only) indicates that Sound Activated Video Alert is on. This means the monitor automatically switches on whenever the camera detects sound. See page 18 for instructions on turning this on and off. (parent unit only) indicates that Temperature Alert is on. This means the monitor shows an alert message if the temperature at a camera gets too high or too low. See page 19 for instructions on setting temperature alerts. 72º 2:35 PMTemperature reading72º 2:35 PMParent monitorMini monitorNote: On the mini monitor, the icon indicates that one or more alerts (low battery, motion, sound activated video, or temperature) are active.
Tour of the system11 indicates the Lullabies are playing through one of the cameras. See page 24 for instructions on playing lullabies. indicates that the camera is using night vision. The cameras automatically switch to night vision when they detect that the room has gotten dark. indicate that the monitor is scanning through the available cameras. The number indicates how quickly the monitor switches cameras. See page 17 for information on turning camera scanning on and off. indicates the level of the monitor’s rechargeable battery. If you see or in this space, it’s time to recharge. See page 3 for more information.On-Screen Indicatorsappears when you’ve pressed the TALK button and are talking through the camera’s speaker. See page 8 for more information.appears when the monitor cannot get the signal from the active camera or when another monitor is in use. See page 27 for more information. appears when a Temperature Alert has been triggered because your baby’s room is too hot or cold. appears when the monitor’s rechargeable battery has less than 10% charge.
Tour of the system12CameraNighttime sensorPower (right side) turns the camera on and off (press and hold).Pair (bottom) links the camera securely with the monitors (press and hold).DC In (back) plugs into your charging cable to recharge or power the camera.Mounting keyholes (bottom) let you mount the camera on a wall (mounting hardware not included).Adjustable antenna communicates wirelessly with the parent and mini monitors.MicrophonePair buttonMounting keyholesDC InAdjustable antenna
Everyday use133. EVERYDAY USEThis system’s menus let you set up more cameras, set motion and temperature alerts, and much more. This section takes you through each menu.12:00AM72º 12:00AMParent Monitor MenuMini Monitor MenuGETTING AROUND IN THE MENUSPress MENU to access the menus.Use the arrows to highlight items.Press OK/ZOOM to select.On the Parent Monitor On the Mini MonitorPress MENU to access the menus.Use the joystick to highlight items.Press OK/ZOOM to select.
Everyday use14CamerasThe Cameras menu lets you pair additional cameras or remove them from your list of cameras. It also lets you change the volume of the audio coming from the camera speaker, or view several cameras at once, using multi-view on your monitor or scanning through them one by one. Parent MonitorMini Monitor ACCESSING THE CAMERAS MENU1 Press MENU on the parent monitor or mini monitor. 2 Use the arrow buttons or joystick to highlight the Cameras icon, and press OK/ZOOM to select it.PAIRING AN ADDITIONAL CAMERANote: Before you start pairing the monitors with your new camera, bring the camera into the same room so that you have it handy. You can put it back in the baby’s room once you’ve finished pairing. Make sure the camera is plugged in and turned on before you start.IMPORTANT: Pair the parent monitor FIRST, before you pair the mini monitor.1 In the Cameras menu, press the down arrow to highlight Pair Camera. Press OK/ZOOM to select it. 12:00AMView CameraPan/Tilt CameraScan CamerasPair CameraDelete CameraCamera VolumeParent MonitorMini MonitorTopFrontFront72º 12:00AMView CameraScan CamerasPair CameraDelete CameraCamera Volume
Everyday use1512:00AMView CameraPan/Tilt CameraScan CamerasPair CameraDelete CameraCamera VolumePair: Camera 1Pair: Camera 2Pair: Camera 3Pair: Camera 42 Press the Pair button on the bottom of the new camera. 3 Use the up/down arrows to select Pair: Camera 2, Pair: Camera 3, or Pair: Camera 4. Press OK/ZOOM to select it.4 If the monitor screen shows a green checkmark next to Pair: Camera, you’re all set to use the monitor and the camera! (If it shows a red X, put the camera closer to the monitor and try again.)5 Once you’ve paired your new camera with the parent monitor, repeat steps 1 and 2 to pair the new camera to the mini monitor. Press OK when the mini monitor asks you if you want to pair.PANNING AND TILTING THE CAMERAThere are two ways of accessing the remote pan and tilt function on the parent and mini monitors: by pressing and holding the OK/ZOOM button or through the menu system.Note: On the parent monitor, camera pan/tilt is in the Cameras menu. On the mini monitor, there’s a separate pan/tilt menu, accessible by the icon in the main menu.1 In the Cameras menu, press the down arrow to highlight Pan/Tilt Camera. Press OK/ZOOM to select it.2 Use the arrow buttons (or joystick on the mini monitor) to pan and tilt the active camera. Press MENU to return to the Cameras menu.12:00AMView CameraPan/Tilt CameraScan CamerasPair CameraDelete CameraCamera VolumeTIP: You can also access pan and tilt by pressing and holding the OK/ZOOM button on the parent monitor or mini.
Everyday use1612:00AMView CameraPan/Tilt CameraScan CamerasPair CameraDelete CameraCamera VolumeVIEWING AND SCANNING CAMERASIf you have more than one camera set up, you can customize how you view them.To view a dierent camera:1 In the Cameras menu, highlight View Camera. Press OK/ZOOM to select it. 2 Use the up/down arrows to select the camera you want to view. Press OK/ZOOM to select it. The screen switches to that camera, and the status bar at the top of the screen indicates the camera you’re viewing: , , , or .12:00AMView CameraPan/Tilt CameraScan CamerasPair CameraDelete CameraCamera VolumeView: Camera 1View: Camera 2View: Camera 3View: Camera 4Multi-view72ºTIP: You can also switch cameras by pressing and holding the VIDEO ON/OFF button on the parent monitor (VIDEO on the mini).To display multiple cameras:1 In the Cameras menu, highlight View Camera. Press OK/ZOOM to select it. 2 Use the up/down arrows to select Multi-view. Press OK/ZOOM to select it. To go back to viewing a single camera, select View Camera from the Cameras menu again. Then highlight the camera you want to view and press OK/ZOOM to select it. TIP: To return to viewing a single camera by highlighting the camera image you want and pressing OK/ZOOM.
Everyday use17To scan through the cameras automatically:1 In the Cameras menu, highlight Scan Cameras. Press OK/ZOOM to select it.2 Use the up/down arrows to select how quickly you want to switch cameras: every 5, 10, or 15 seconds. Press OK/ZOOM to select that option. The screen switches to the first camera, and the status bar at the top of the screen shows an indicator for scanning: , , or . It also shows the camera you’re viewing. To stop scanning cameras: select Scan Cameras in the Cameras menu. Then select Scan: Off.12:00AMView CameraPan/Tilt CameraScan CamerasPair CameraDelete CameraCamera VolumeScan: OffScan: 5 SecsScan: 10 SecsScan: 15 Secs72ºREMOVING A CAMERA FROM THE LIST1 In the Cameras menu, highlight Delete Camera. Press OK/ZOOM to select it. 2 Use the up/down arrows to select the camera you want to remove from the list. Press OK/ZOOM to select it. The screen confirms that the camera has been deleted. IMPORTANT: In order to use this camera with the system, you’ll need to pair it with both monitors again.ADJUSTING CAMERA VOLUME1 In the Cameras menu, highlight Camera Volume. Press OK/ZOOM to select it. 2 Use the up/down arrows to select the volume level you want for the audio from the camera’s speaker. Press OK/ZOOM to select it. 12:00AMView CameraPan/Tilt CameraScan CamerasPair CameraDelete CameraCamera VolumeDelete: Camera 1Delete: Camera 2Delete: Camera 3Delete: Camera 472ºNOTE: You must have more than one camera paired with a monitor in order to scan cameras.12:00AMView CameraPan/Tilt CameraScan CamerasPair CameraDelete CameraCamera VolumeLowMedHigh72º
Everyday use18SETTING UP MOTION ACTIVATIONYou can set up the monitor so that it automatically shows video when the camera detects that your baby is moving.1 In the Motion/Alerts menu, press OK/ZOOM to select Motion Activated Video. 12:00AMMotion Activated Video: OFFSound Activated Video: OFFTemperature Alert: OFFLow Battery Noise Alert: OFF72ºMotion/AlertsThe Motion/Alerts menu lets you set up alerts that are activated by motion, sound, or temperature in your baby’s room. It also lets you set up an alert for when the monitor’s rechargeable battery needs to be recharged. ACCESSING THE MOTION/ALERTS MENU1 Press MENU on the parent monitor or mini monitor. 2 Use the arrow buttons or joystick to highlight the Motion/Alerts icon, and press OK/ZOOM to select it.Parent Monitor72º 12:00AMMotion Activated Video: OFFSound Activated Video: OFFTemperature Alert: OFFLow Battery Noise Alert: OFFMini MonitorParent MonitorMini MonitorTopFrontFront
Everyday use19SETTING UP SOUND ACTIVATIONYou can set up the monitor so that it automatically shows video when the camera detects sound from your baby.1 In the Motion/Alerts menu, press OK/ZOOM to select Sound Activated Video. 2 Use the up/down arrows to select the amount of sensitivity you want for the sound sensor: ON: Low, ON: Medium, or ON: High. The status bar at the top of the screen shows an indicator for sound activation: . Note: You might want to test different levels of sensitivity for this alert, to find the best fit for your environment and preference.12:00AMMotion Activated VideoSound Activated VideoTemperature AlertLow Battery Noise Alert72ºOFFON: LOWON: MediumON: High2 Use the up/down arrows to select the amount of sensitivity you want for the motion sensor: ON: Low, ON: Medium, or ON: High. The status bar at the top of the screen shows an indicator for motion activation: . Note: You might want to test different levels of sensitivity for this alert, to find the best fit for your environment and preference.12:00AMMotion Activated VideoSound Activated Video: OFFTemperature Alert: OFFLow Battery Noise Alert: OFF72ºOFFON: LOWON: MediumON: HighParent Monitor72º 12:00AMMotion Activated VideoOFFON: LowON: MediumON: HighMini Monitor
Everyday use20SETTING TEMPERATURE ALERTSThese alerts tell you when your baby’s room is too hot or too cold.1 In the Motion/Alerts menu, select Temperature Alert. 2 Activate the temperature alert you want to use, then set it. The status bar at the top of the screen will show an indicator for temperature alerts: . To set a high temperature alert: Highlight High Temp: ON and press OK/ZOOM. Use the up/down arrows to set the temperature you want to set for the high temperature alert. Press OK/ZOOM to set it. To set a low temperature alert: Highlight Low Temp: ON and press OK/ZOOM. Use the up/down arrows to set the temperature you want to set for the high temperature alert. Press OK/ZOOM to set it. If the temperature in your baby’s room goes beyond the limit(s) you set, the parent monitor displays an alert.SETTING A LOW-BATTERY ALERTThis alert tells you when the monitor needs to be recharged.1 In the Motion/Alerts menu, highlight Low Battery Noise and press OK/ZOOM to select it. 2 Use the up/down arrows to select how loud you want this alert: ON: Low or ON: High. The status bar at the top of the screen shows an indicator for the low-battery alert: .12:00AMMotion Activated Video: OFFSound Activated Video: OFFTemperature Alert: OFFLow Battery Noise72ºOFFON: LowON: High12:00AM72ºHigh Temperature levelhas been detectedCamera 1: 81º FOK12:00AMMotion Activated Video: OFFSound Activated Video: OFFTemperature AlertLow Battery Noise Alert: OFF72ºHigh Temp: ON: 81 OFFLow Temp: ON: 63 OFF
Everyday use2112:00AMTake PictureRecord Video72º RECORDING AN IMAGE OR VIDEO1 In the Record menu, highlight Take Picture or Record Video. Press OK/ZOOM to select that option.2 Follow the on-screen instructions to take the picture or make the video. See the instructions on the next page to display your picture or video on the parent monitor. RecordingThe Recording menu lets you record video or take a picture of your baby. ACCESSING THE RECORDING MENU1 Press MENU on the parent monitor. 2 Use the arrow buttons to highlight the Recording icon, and press OK/ZOOM to select it.IMPORTANT: You must have a Micro SD card (included in model PNM5W01S; not included with other models) inserted in the MICRO SD slot on the side of the parent unit in order to record images or video. See page 8 for more information. Only the parent monitor can record. The Mini Monitor does not have this capability.
Everyday use2212:00AMView Saved PicturesView Saved Videos72ºPLAYING BACK IMAGE OR VIDEO1 In the Play menu, select View Saved Pictures or View Saved Videos.2 Select the image or video you want to see on the display. Press OK/ZOOM to select it.3 Use the on-screen controls to stop, play/pause, and exit the screen.Playing Back Pictures and VideosThe Play menu lets you access the videos or pictures you’ve taken with the system.ACCESSING THE PLAY MENU1 Press MENU on the parent monitor. 2 Use the arrow buttons to highlight the Play icon, and press OK/ZOOM to select it.IMPORTANT: You must have a Micro SD card (included in model PNM5W01S; not included with other models) inserted in the MICRO SD slot on the side of the parent unit in order to record images or video. See page 8 for more information. Only the parent monitor can record. The Mini Monitor does not have this capability.To delete a video: Highlight the video you want to delete. Then press the left arrow and press OK/ZOOM to confirm. The screen will display the video file name with an X.
Everyday use2312:00AMSleep Mode (video off, sound on)72ºOFFON: 5 minsON: 30 minsON: 60 minsSETTING SLEEP MODE1 In the Sleep Mode menu, press OK/ZOOM to turn sleep mode on.2 Use the up and down arrows to select the delay before the display turns off automatically: 5, 30, or 60 minutes. (The audio from your camera will stay on even when the display is off.) Sleep ModeYou can set up your monitors to turn off the display automatically after a set amount of time. Parent Monitor72º 12:00AMVideo Off, Sound OnOFFON: 5 minsON: 30 minsON: 60 minsMini MonitorACCESSING THE SLEEP MODE MENU1 Press MENU on the parent monitor or mini monitor. 2 Use the arrow buttons or joystick to highlight the Sleep Mode icon, and press OK/ZOOM to select it.Parent MonitorMini MonitorTopFrontFront
Everyday use24LullabiesThis Project Nursery system comes with 3 lullabies, 2 nature sounds, and white noise ready to play—simply choose the one you want, and the camera you’re on will play it back.PLAYING LULLABIES OR WHITE NOISE1 Make sure the monitor is displaying the camera you want to play the lullaby on. If you want to play on a different camera, press the MENU button and select CAMERAS. Then press OK/ZOOM to select View Camera and choose the camera you want.2 Press the MENU button to access the main menu.3 Highlight LULLABIES and press OK/ZOOM to choose it.4 Highlight the option you want to play and press OK/ZOOM to start playing it. The status bar at the top of the screen shows an indicator for lullabies: .12:00AM72º“I Don’t Want to Miss a Thing”“Holiday”“Jolene”WavesRainWhite NoisePlay AllParent Monitor72º 12:00AM“I Don’t Want to Miss a Thing”“Holiday”“Jolene”WavesRainWhite NoisePlay AllMini MonitorNOTE: If there’s a lullaby currently playing on a camera, a green arrow icon appears next to it. Parent MonitorMini MonitorTopFrontFront
Everyday use25ContrastYou can adjust the contrast and brightness of the display, and set it to automatically dim after a set amount of time. 12:00AMAdjust ContrastAdjust BrightnessAuto Dimming72ºParent MonitorMini Monitor72º 12:00AMAdjust ContrastAdjust BrightnessAuto DimmingADJUSTING CONTRAST OR BRIGHTNESS1 Press MENU on the parent monitor or mini monitor. 2 Use the arrow buttons or joystick to highlight the Contrast icon, and press OK/ZOOM to select it.3 In the Contrast menu, highlight the option you want to adjust, Adjust Contrast or Adjust Brightness, and press OK/ZOOM to select it.4 Use the up and down arrows to adjust the option you chose. Press OK/ZOOM when you’ve finished.SETTING AUTO DIMMING1 In the Contrast menu, highlight Auto Dimming. Press OK/ZOOM to select it.2 Use the up and down arrows to choose the delay for auto dimming the display: 5, 10, or 30 minutes. Press OK/ZOOM to select.Parent MonitorMini MonitorTopFrontFront
Everyday use26SettingsThe Settings menu lets you customize the monitors to match your preferences. It also gives you technical information about the monitor and support. ACCESSING THE SETTINGS MENU1 Press MENU on the parent monitor or mini monitor. 2 Use the arrow buttons or joystick to highlight the Settings icon, and press OK/ZOOM to select it.12:00AMTemperatureTime SetFactory ResetSupportProduct InformationSD Card InformationParent MonitorMini Monitor72º 12:00AMTemperature C/FTime SetFactory ResetSupportProduct InformationButton InformationSETTING YOUR TEMPERATURE PREFERENCE1 In the Settings menu, press OK/ZOOM to select Temperature.2 Use the up and down arrows to select how you’d like temperature to be displayed: in degrees Fahrenheit or Celsius. Press OK/ZOOM when you’ve finished.Parent MonitorMini MonitorTopFrontFront
Everyday use27SETTING THE TIME AND DATE1 In the Settings menu, press the down arrow to highlight Time Set. Press OK/ZOOM to select it. 2 Use the up/down arrow buttons to set the date. 3 After setting the year, press the right arrow to adjust the time. Then use the up/down arrows to set the time. Press OK/ZOOM when you’re finished.RESETTING TO FACTORY SETTINGSIf you’ve tried all of the troubleshooting solutions to solve a problem, and nothing seems to work, you might need to reset the monitor to its factory settings and start setup again. WARNING: Resetting to factory settings erases all of your custom settings. You will have to set up the monitor from scratch. GETTING SUPPORT AND TECHNICAL INFORMATION1 In the Settings menu, press the down arrow to highlight one of the support or technical information options: Support, Product Information, or SD Card Information. Press OK/ZOOM to select it. 2 Press OK/ZOOM to exit.12:00AMTemperatureTime SetFactory ResetSupportProduct InformationSD Card InformationDate: 01/01/16Time: 12:00 AM12:00AMTemperatureTime SetFactory ResetSupportProduct InformationSD Card InformationReset all settingsto default?NOTE: The mini monitor offers an additional Button Information option in the Settings menu, with shortcut info for adjusting pan/tilt/zoom and volume, and switching cameras.
Troubleshooting284. TROUBLESHOOTING / FAQSMost issues with the Project Nursery baby monitoring system can be solved by following one of the troubleshooting tips below. For additional assistance, please call 1-844-393-7338.I don’t see video from the camera on my monitor.+ Make sure your monitor is turned on (press the Power button). If it is, press the VIDEO ON/OFF button (VIDEO on the mini monitor) to make sure the monitor’s display is awake. Make sure the camera is plugged in to a working outlet and turned on. I see the icon on the screen.+ Make sure the camera you’re trying to view is plugged in to a working outlet and turned on.+ Make sure the monitor is within range (maximum 800 ft) of the camera you’re trying to display (certain kinds of signal obstacles, like large metal objects, might shorten the range somewhat).+ If the other monitor is on, power it off. To keep this baby monitoring system as secure as possible, only one monitor can view video at a time. If you want to use the mini monitor, for example, make sure you power the parent monitor off (and vice-versa).+ The monitor you’re using might have become un-paired with the camera. See page 15 for instructions on pairing a monitor and camera.I can’t record video or pictures.+ Make sure you have an Micro SD card (included with the PNM5W01S; not included with other models) inserted in the MICRO SD card slot on the side of the parent monitor.I can’t pan/tilt the camera from my monitor.+ Make sure you’re in pan mode—press and hold OK/ZOOM until you see arrows on the monitor display. Then use the arrows or joystick to pan the camera.+ Make sure you’re not zoomed in on the image—press OK/ZOOM to zoom out if you are. Then press and hold OK/ZOOM to enter pan mode.
Troubleshooting29Continues on the next page...+ Make sure the camera is moving freely. In certain positions, the camera might bump into stand neck. If the neck is in the way, pan or tilt the camera in the other direction so that you have a free range of movement. I can’t hear sounds from baby’s room.+ Make sure the monitor is turned up. Press the VOL+ button until you hear sounds from your baby’s room.+ Make sure the microphone on the camera is not blocked. The microphone is just above the lens.The lullabies aren’t playing.+ If you have multiple cameras, make sure you’ve chosen the one you want the lullabies to play on before you start the lullaby. Go to Cameras > Select Camera and choose the camera you want. Then go to Lullabies and select an option to play.The temperature alerts don’t work.+ Make sure you’ve set the temperature preference to the system you use, Fahrenheit (standard in the US) or Celsius (standard outside the US). To switch your temperature preference, go to Settings > Temperature.+ Make sure you’ve set the right kind of temperature alert—for example, if you want to make sure your baby’s room does not get below 68 degrees Fahrenheit, set the Low Temp Temperature Alert to 68. If you want to make sure your baby’s room doesn’t get above a certain temperature, set the High Temp Temperature Alert to that temperature.Motion alerts don’t work.+ You might need to adjust the sensitivity of the alerts—for example, if Motion Activated Video is set to ON: Low, the monitor will not come on as often as when Motion Activated Video is set to ON: Medium or ON: High. To adjust this setting, go to Motion/Alerts > Motion Activated Video. + If you have multiple cameras, you might need to change the active camera—motion alerts work for the active camera only. Press VIDEO ON/OFF (VIDEO on the mini monitor) to make sure the camera you want to use for motion alerts—the one with the clearest view of your baby, for example—is the one displayed.
Troubleshooting30Sound alerts don’t work.+ You might need to adjust the sensitivity of the alerts—for example, if Sound Activated Video is set to ON: Low, the monitor will not come on as often as when Sound Activated Video is set to ON: Medium or ON: High. To adjust this setting, go to Motion/Alerts > Sound Activated Video. + If you have multiple cameras, you might need to change the active camera—sound alerts work for the active camera only. Press VIDEO ON/OFF (VIDEO on the mini monitor) to make sure the camera you want to use for sound alerts—the one closest to your baby, for example—is the one displayed.
©2016 Voxx Accessories Corp. 3502 Woodview Trace, Suite 220 Indianapolis, IN 46268 PNM4-5W01-S UG 01

Navigation menu