Voxx Accessories PNMWIFIAC 720p WiFi Baby Monitor User Manual

Voxx Accessories Corp. 720p WiFi Baby Monitor

User Manual

WIFI BABY MONITOR
User Guide
What’s inside
Welcome!................................................................. 2
Getting started ...................................................... 3
Tour of the system ............................................... 9
Everyday use .........................................................13
Motion detection ...........................................14
Sound detection ............................................14
Auto-record time .......................................... 15
Battery life........................................................15
Temperature alarm .......................................16
Music ...................................................................16
Share camera with friend ..........................17
Flip horizontally / vertically .....................18
Camera time set ............................................18
Camera info .....................................................19
Delete Camera ...............................................19
Troubleshooting / FAQs ................................. 20
PNMWIFIAC
2
Step 1: Unpack
WELCOME!
This WiFi Baby Monitor makes it
simple to keep your eyes and ears
on your little one from anywhere!
This guide takes you through the
steps to get started!
Before you start...
Make sure you read the Important Information
sheet included in this package.
WiFi camera
The accessories:
(1) Power adapter
(1) 10’ charging cable
(2) Mounting screws
Check out our setup videos
On your computer, go to
http://bit.ly/pnwifi-setup or scan the
QR code here.
3
Getting Started
Find a location for the camera
that gives you the best view of
your baby in his or her crib.
Place the camera on a flat surface, like a dresser
or shelf, or mount the camera to a wall using the
keyhole slots on its bottom (see the mounting
template included in this package).
IMPORTANT: NEVER place the camera or cords of
any kind inside the crib. NEVER place the camera
or cords within reach of the baby.
Step 2: Position the camera
GETTING STARTED
WARNING
Strangulation Hazard:
Children have STRANGLED
in cords. Keep this cord out
of the reach
of children
(more than
3ft (0.9m)
away).
Never use
extension
cords with AC Adapters.
Only use the AC Adapters
provided.
4
Plug one end of the
included charging cable
into the DC In jack on the
back of the camera.
Plug the other end into
the included power
adapter. Then plug the
adapter into an outlet or
surge protector.
The camera turns on
automatically when you
plug it in (the indicator
light on its back panel
turns solid red).
Step 4: Plug in the camera
Getting Started
Your Project Nursery WiFi Camera needs strong
enough signal from your WiFi router in order to
send its video signal.
Here’s how to test the strength of your WiFi signal
in your baby’s nursery using your smartphone or
other portable wireless device (like a tablet or iPod
touch).
First, go to where you want to put the camera.
Make sure your smartphone
or other portable wireless
device is connected to the
WiFi network you want to
test. Look at the WiFi icon on
your device screen to see the
strength of the connection.
For example, on iOS devices
look in the upper left-hand
corner of the screen for the
WiFi icon (shown here).
For best results, look for a location with at least
50% strength to use the WiFi camera.
Step 3: Test your WiFi signal
5
Getting Started
Step 5: Download and install the
Project Nursery Monitor App on
your phone or tablet
In the Google Play or Apple App
Stores, search for “PROJECT
NURSERY MONITOR” and look
for the icon shown here. Then
download and install the App.
®
Register
Login
Sign Up
Username
Email Address
Password
Confirm Password
Sign Up
Step 7: Create a Project Nursery
user name and password
The first time you launch the
Project Nursery App, you’ll
need to create a user name
and password so that you can
access your camera securely.
Press the Register button to
start, then follow the steps to
set up your account.
IMPORTANT: Make sure you
give a valid email address that
you have easy access to. The
App will use this address if
you ever need to recover or
reset your password.
Once you’ve finished
creating your user name and
password, the App will ask
you to Login with the name
and password you created.
IMPORTANT: Your user
name cannot contain special
characters (like “@”)—only
letters and numbers.
Step 6: Launch the Project
Nursery Monitor App
Once the Project Nursery Monitor App has
installed on your smarphone or tablet, press the
icon to launch the App.
6
®
Device List Message My Center
Getting Started
Step 8: Pair the WiFi camera with
the App.
Make sure the Project Nursery App is open on your
phone or tablet. Also make sure that your phone
or table is connected to your WiFi network.
In the next screen, press the
Add new camera with WiFi
button.
The App will prompt you to
make sure your camera is on.
If you haven’t already turned it
on, press the POWER button
on the right side of the camera
(the camera’s LED lights up),
then press the Next step button
in the App.
The next screen in the App lets
you name the camera you’re
setting up and prompts you
to scan the QR code on the
bottom of the camera.
To name the camera you’re
setting up: Press in the
Camera name field and enter
the name you want to use.
In the App’s home screen,
press the icon (Add
Camera) in the upper right
corner of the screen.
®
Device List Message My Center
To scan the QR code on the
WiFi camera: Find the QR
code on the bottom of the
WiFi camera. Position your
smartphone or tablet so
that its camera can scan this
QR code. Then press where
indicated in the App to scan
this QR code.
Add new camera with WiFi
Add Camera
Get shared camera from friend
Add new camera with QR code
Add Camera
Scan QR code located
on bottom of camera
ID:
Sally’s Nursery
Camera name:
Next step
Press to open
QR code scanner
7
Getting Started
After you’ve scanned the QR
code on the bottom of the
WiFi Camera, the App will ask
you to press the SET button on
the bottom of the camera and
enter the name (WIFI SSID)
and password of your WiFi
network.
Enter the name (WIFI SSID)
and password for your home
WiFi network in the App.
Find the SET button on the
bottom of the WiFi camera.
Press it for one second (until
the camera gives an audio
signal).
IMPORTANT: Double check that you’ve typed your
network name and password correctly—otherwise,
the camera won’t work with the App!
Once you’ve finished entering your network name
and password, press the Next step button on the
App screen. The indicator light on the back of the
WiFi camera starts flashing—the camera is trying
to join your WiFi network.
Congratulations!
Camera successfully added!
Configure WiFi
Once the WiFi camera has
successfully connected to your
WiFi network, you’ll see the
Success screen in the App and
the indicator light on the back
of the camera will turn green.
Congratulations—you’ve just
set up your first camera!
IMPORTANT: If the WiFi
camera does not connect,
follow the instructions in the
App to troubleshoot.
Configure WiFi
Next step
1. Your camera should be plugged in and turned ON.
Press the “Set” button on the bottom of your camera for 1
second.You will hear one beep and the LED will start
blinking red.
2. Choose WiFi SSID (or network name) and enter
password below. Make sure you enter the info correctly.
If your WiFi SSID does not have a password, you will need to
create one. This is for your safety and security. Consult the
user guide for your WiFi router/AP to add a password.
Helpful Hint: Click on the lock icon in the password area
to hide or display text.
3. After you’ve entered your WiFi info below, press “Next
step.” Your camera will begin connecting to your WiFi
network. This can take 2–3 minutes to complete.
When you hear two beeps and the LED turns solid green,
your camera is successfully connected and ready for you to use.
Configure WiFi
Next step
1. Your camera should be plugged in and turned ON.
Press the “Set” button on the bottom of your camera for 1
second.You will hear one beep and the LED will start
blinking red.
2. Choose WiFi SSID (or network name) and enter
password below. Make sure you enter the info correctly.
If your WiFi SSID does not have a password, you will need to
create one. This is for your safety and security. Consult the
user guide for your WiFi router/AP to add a password.
Helpful Hint: Click on the lock icon in the password area
to hide or display text.
3. After you’ve entered your WiFi info below, press “Next
step.” Your camera will begin connecting to your WiFi
network. This can take 2–3 minutes to complete.
When you hear two beeps and the LED turns solid green,
your camera is successfully connected and ready for you to use.
8
Getting Started
Step 9: Choose the camera from
the home screen
Press the part of the home
screen showing the camera
you set up in order to choose
this camera.
®
Device I D：1234567 891234560
Device List Message My Center
Sally’s nursery
0
RE CORDSNAPSHOT
TALKSOUND ON
H D SD
2016-1-28-12:00
JOYSTICK
Sally’s nursery The Camera View screen is
your gateway to total control
of your WiFi camera from
virtually anywhere.
The next chapter gives you a
tour of the features available
from this screen.
®
Devic e ID：123 456789123 456 0
Device List Message My Center
Sally’s nursery
9
TOUR OF THE SYSTEM
Tour of the system
0
R E CORDSNAPSHOT
TALKSOUND O N
H D SD
2016-1-28-12:00
JOYSTICK
Sally’s nursery
Camera View Screen
(Settings) accesses the Settings menu for this camera. Press this
icon to adjust the WiFi and other settings for this camera.
(Multi-Camera View) lets you see multiple cameras at once on
a single screen (if you’ve set up multiple cameras). Press this icon to
access the multi-camera view screen.
H D SD (HD-SD Select) lets you switch between high- and standard-
definition video on the view screen.
(Micro-SD Card) accesses any content stored on the camera’s
Micro-SD Card (not included). Press this icon to start viewing or
downloading motion/sound-activated videos or images from the
camera’s Micro-SD Card. (This is where you’ll see auto recordings.)
RE C ORD (Record) starts/stops recording video. The video file is saved to
your smartphone or tablet.
SNAPSHOT (Snapshot) takes a still photo of the camera video. The snapshot
file is saved to your smartphone or tablet.
10
Tour of the system
0
R E CORDSNAPSHOT
TALKSOUND O N
H D SD
2016-1-28-12:00
JOYSTICK
Sally’s nursery
JOYSTICK (Joystick) moves the camera angle. Press and hold in the
direction you want the camera angle to move. (You can also pan/
tilt by swiping on the screen in the direction you want to move.)
TALK (Talk) lets you speak through this camera’s built-in speaker.
Press and hold this icon to start speaking.
SOUND O N
(Sound On/Off) turns the sound from the camera on and off.
11
Tour of the system
POWER button
(right side) turns
the camera on
and off (press and
hold).
Camera (front)
Nighttime sensor
adjusts the camera
sensitivity to the
amount of ambient
light.
Microphone picks
up sound around
the camera.
Camera (back)
DC In jack plugs
into your charging
cable to power the
camera.
Adjustable antenna
communicates wirelessly
with your WiFi network.
Indicator light
shows the power
and connection
status of the camera:
- off (camera not
plugged in or
powered on)
- solid red (on but
not connected
- blinking red (in
the process of
connecting)
- solid green
(connected to
network and App)
- blinking green
(camera being
actively viewed).
Thermal sensor detects the
temperature around the
camera.
12
Tour of the system
SET starts the WiFi setup process (press and
hold).
QR code passes the camera ID information to the
App during the WiFi setup process.
Mounting keyholes
let you mount the
camera on a wall
(mounting screws
included).
MICRO-SD slot
(left side) accepts
a micro-SD card
(not included)
for storage of
automatic photos/
video.
Camera (bottom)
13
Everyday use
3. EVERYDAY USE
In the Camera View screen, press the
(Settings) icon to customize your
WiFi camera’s setup.
This chapter takes you through the
settings you can customize, one by
one.
0
RE CORDSNAPSHOT
TALKSOUND ON
H D S D
2016-1-28-12:00
JOYSTICK
Sally’s nursery
HMOFF
L
Share camera with friend
Delete Camera
Battery Life
Auto-record time
Music
White Noise
Settings
Motion detection
Sound detection
OFF
L
Temperature alarm
Camera time set
H
Camera info
20s 60s 90s
Flip horizontally
Flip vertically
14
Everyday use
Motion detection
You can set up the App and camera so that you get a notification
on your phone and the camera automatically records video when
the camera detects that your baby is moving.
To set up motion detection: In the Settings menu, press the
Motion detection sensitivity setting you want to use: OFF, L (low),
M (medium), or H (high).
Note: You might want to test different levels of sensitivity for this
setting, to find the best fit for your environment and preference.
HMOFF
L
Share camera with friend
Delete Camera
Battery Life
Auto-record time
Music
White Noise
Settings
Motion detection
Sound detection
OFF
L
Temperature alarm
Camera time set
H
Camera info
20s 60s 90s
Flip horizontally
Flip vertically
Sound detection
You can set up the App and camera so that you get a notification
on your phone and the camera automatically records video when
the camera detects sound from your baby.
To set up sound detection: In the Settings menu, press the Sound
detection sensitivity setting you want to use: OFF, L (low), or H
(high).
Note: You might want to test different levels of sensitivity for this
setting, to find the best fit for your environment and preference.
HMOFF
L
Share camera with friend
Delete Camera
Battery Life
Auto-record time
Music
White Noise
Settings
Motion detection
Sound detection
OFF
L
Temperature alarm
Camera time set
H
Camera info
20s 60s 90s
Flip horizontally
Flip vertically
IMPORTANT: You must have a
micro SD card installed in your
WiFi camera to use the auto-
recording function of this feature.
IMPORTANT: You must have a
micro SD card installed in your
WiFi camera to use the auto-
recording function of this feature.
Notes about notifications:
+ Pressing on a sound- or motion-detection notification or going to messages shows you a screenshot
of the motion detection event. To view the video, press the icon in the camera view screen.
+ The App sends a maximum of 2 notifications every 4 minutes. It prioritizes notifications in the
following order: temperature, sound, motion.
15
Everyday use
Auto-record time
You can set up the camera so that it automatically records a
certain amount of video when the camera detects a motion or
sound alert.
To set up an auto-record time: In the Settings menu, press the
amount of Auto-record time you want (in seconds) when a
motion or sound alert is triggered: 20s, 60s, or 90s.
HMOFF
L
Share camera with friend
Delete Camera
Battery Life
Auto-record time
Music
White Noise
Settings
Motion detection
Sound detection
OFF
L
Temperature alarm
Camera time set
H
Camera info
20s 60s 90s
Flip horizontally
Flip vertically
IMPORTANT: You must have a
micro SD card installed in your
WiFi camera to use this feature.
Camera battery fully charged
Camera battery low: 25%
Camera battery critically low
Push Notifications for Camera Battery
Battery Life Battery life
This setting tells the battery status of rechargeable WiFi cameras.
IMPORTANT: This setting does not apply to this WiFi camera.
HMOFF
L
Share camera with friend
Delete Camera
Battery Life
Auto-record time
Music
White Noise
Settings
Motion detection
Sound detection
OFF
L
Temperature alarm
Camera time set
H
Camera info
20s 60s 90s
Flip horizontally
Flip vertically
16
"I Don't Want to Miss a Thing"
"Holiday"
"Jolene"
Rain
Waves
White Noise
Music
Everyday use
HMOFF
L
Share camera with friend
Delete Camera
Battery Life
Auto-record time
Music
White Noise
Settings
Motion detection
Sound detection
OFF
L
Temperature alarm
Camera time set
H
Camera info
20s 60s 90s
Flip horizontally
Flip vertically
Temperature alarm
These alerts tell you when your baby’s room is too hot or too cold.
1 In the Settings menu, press Temperature alarm.
2 In the Temperature alarm menu, press Edit at the top of the
screen to change the settings.
To change from degrees Fahrenheit to Celsius: Press the C.
To set a high temperature alert: Press the switch next to
High temperature alert. Then set the temperature you want
for the high temperature alert.
To set a low temperature alert: Press the switch next to Low
temperature alert. Then set the temperature you want for
the high temperature alert.
If the temperature in your baby’s room goes beyond the limit(s)
you set, you will get a push notification on your phone or tablet.
HMOFF
L
Share camera with friend
Delete Camera
Battery Life
Auto-record time
Music
White Noise
Settings
Motion detection
Sound detection
OFF
L
Temperature alarm
Camera time set
H
Camera info
20s 60s 90s
Flip horizontally
Flip vertically
Music
This Project Nursery system comes with 3 lullabies, 2 nature
sounds, and white noise ready to play—simply choose the one
you want, and the camera you’re on will play it back.
To play a lullaby, nature sound, or white noise from the active
camera: Press Music in the Setup menu. Then press the option
you want to play.
Note: Make sure you’re displaying the camera you want to play
the lullaby on. If you want to play on a different camera, go back
to the App’s home screen and choose that camera.
17
Share with friend
Add Camera
De ci ce List
Steps to share with friend
Step 1: Open App and click then
“Add camera” button above in
your friend’s mobile phone
Step 2: Select the third option and scan
the QR code above
Add new camera with WiFi
Get shared camera from friend
Add new camera with QR code
Everyday use
Share camera with friend
The Project Nursery WiFi Camera lets you share video with
friends and family, so that they can see what’s happening with
baby. These guest accounts have limited access to settings—they
can view and talk through cameras and record pictures and
videos directly to their phone.
1 Make sure the person you want to share with has
downloaded the Project Nursery App on their phone or
tablet.
2 On your phone or tablet, go to the Settings menu and press
Share camera with friend. Have the person you want to
share with follow the steps shown.
IMPORTANT: Your friend or family member will need to scan
the QR code on the screen. If they are not physically present
to do so, either print the screen or do a screenshot and send
it to a phone they can scan with their phone.
HMOFF
L
Share camera with friend
Delete Camera
Battery Life
Auto-record time
Music
White Noise
Settings
Motion detection
Sound detection
OFF
L
Temperature alarm
Camera time set
H
Camera info
20s 60s 90s
Flip horizontally
Flip vertically
18
The camera time on the screen is from
networ k. If you find the camera time is not
thesame with t he mobile phone, p lease
click the button below to synchronize time.
Camera time sync
Camera time check
Everyday use
Camera time set
The WiFi camera’s internal clock might need to be periodically
syncronized with your phone’s clock. If you notice the two times
don’t match, choose Camera time set in the App’s Settings
menu, and press the Camera time sync button at the bottom of
the page. The App will sync the current WiFi camera’s clock with
your phone or tablet’s clock.
HMOFF
L
Share camera with friend
Delete Camera
Battery Life
Auto-record time
Music
White Noise
Settings
Motion detection
Sound detection
OFF
L
Temperature alarm
Camera time set
H
Camera info
20s 60s 90s
Flip horizontally
Flip vertically
HMOFF
L
Share camera with friend
Delete Camera
Battery Life
Auto-record time
Music
White Noise
Settings
Motion detection
Sound detection
OFF
L
Temperature alarm
Camera time set
H
Camera info
20s 60s 90s
Flip horizontally
Flip vertically
Flip horizontally / vertically
Flip horizontally and vertically let you reverse the orientation
of the Camera View video. Press the switches next to each to
toggle these on and off.
19
215451516514
442412314575756
IP Camera
20130101
BNHS5750101
Device name
Serial #
MAC address
Hardware version
Software version
Device info
Space capacity
Use
Available
3.0GB
2.0GB
Format SD card
Everyday use
Camera info
The Device info screen gives you details about the current WiFi
camera, including the amount of memory left on the micro-SD
card if you have one installed.
The Format SD card button at the bottom of the Camera info
screen lets you format a micro-SD card before you use it for the
first time.
To format a micro-SD card: Insert the card into the WiFi
camera’s micro-SD card slot. Then press the Format SD card
button at the bottom of the Camera info page.
HMOFF
L
Share camera with friend
Delete Camera
Battery Life
Auto-record time
Music
White Noise
Settings
Motion detection
Sound detection
OFF
L
Temperature alarm
Camera time set
H
Camera info
20s 60s 90s
Flip horizontally
Flip vertically
Delete Camera
If you’ve tried all of the troubleshooting solutions to solve a
problem, and nothing seems to work, you might need to reset
the WiFi camera and App to their factory settings and start
setup again. WARNING: Delete camera erases all of your
custom settings. You will have to set up the WiFi camera from
scratch.
HMOFF
L
Share camera with friend
Delete Camera
Battery Life
Auto-record time
Music
White Noise
Settings
Motion detection
Sound detection
OFF
L
Temperature alarm
Camera time set
H
Camera info
20s 60s 90s
Flip horizontally
Flip vertically
20
Troubleshooting
4. TROUBLESHOOTING / FAQS
Most issues with the Project Nursery baby monitoring system can be solved by following one of the
troubleshooting tips below. For additional assistance, please call 1-844-393-7338.
I can’t connect the WiFi camera to my network.
+ Make sure your phone or tablet is connected to the WiFi network you want to use.
+ Make sure the camera is getting a good signal from your WiFi router. See page 4 for more
information.
+ Make sure your router is broadcasting its SSID (name). The Project Nursery WiFi camera does not
support hidden SSIDs.
+ Make sure that Wi-Fi signal is 2.4GHz. The Project Nursery WiFi camera does not support 5GHz WiFi.
+ Make sure that your WiFi router uses either WPA2-PSK/WPA-PSK or AES as its encryption method.
+ Make sure that there is no MAC filter on router or add MAC address to router whitelist.
+ Reset the camera to set up connection again. Press and hold SET key for 10 seconds. The camera will
give a long beep when it is fully reset.
The WiFi camera’s indicator light remains red (connection to network failed).
+ Double check that you’ve entered the correct password for your WiFi network in the Project Nursery
App.
+ Test your WiFi network with other devices to make sure its working.
+ Make sure the camera is getting a good signal from your WiFi router. See page 4 for more
information.
+ Make sure that Wi-Fi signal is 2.4GHz. The Project Nursery WiFi camera does not support 5GHz WiFi.
+ Make sure that your WiFi router uses either WPA2-PSK/WPA-PSK or AES as its encryption method.
21
Troubleshooting
The WiFi camera’s indicator light flashes green.
+ The camera is being actively viewed.
I don’t see video from the camera on my phone/tablet.
+ Make sure the camera is turned on and that it has enough charge or is plugged in to a working outlet.
+ Make sure the camera is within range of your WiFi router (certain kinds of signal obstacles, like large
metal objects, might shorten the range somewhat).
+ Make sure your phone/tablet has an active data or WiFi connection and that the Project Nursery App
is open and configured with the camera.
I can’t record video or pictures on the camera (for motion or sound alerts).
+ Make sure you have an Micro SD card (not included) inserted in the MICRO SD card slot on the side of the
parent monitor.
+ Make sure auto-record is set to on and a motion or sound alert is set.
I can’t record video or pictures on my phone/tablet.
+ Make sure your phone/tablet has enough available memory to record video or pictures.
My video feed is frozen.
+ Check the time stamp on the video feed screen to make sure the video is frozen. Then return to the
camera home screen and reload that camera again.
+ Close the app and re-open.
I can’t pan/tilt the camera from my phone or tablet.
+ Make sure the camera is moving freely. In certain positions, the camera might bump into the stand
neck. If the neck is in the way, pan or tilt the camera in the other direction so that you have a free
range of movement.
The App is frozen.
+ Force close the App on your phone or tablet. Then re-open it.
22
Troubleshooting
I can’t hear sounds from baby’s room.
+ Make sure the volume on your phone or tablet is turned up.
+ Make sure sound is turned on in the Camera view screen.
+ Make sure the microphone on the camera is not blocked. The microphone is just below the lens.
The lullabies/sounds aren’t playing.
+ If you have multiple cameras, make sure you’ve chosen the one you want the lullabies to play on
before you start the lullaby. Go to the Home screen and choose the camera you want. Then go to
Settings, then Music and select an option to play.
The temperature alerts don’t work.
+ Make sure you’ve set the temperature preference to the system you use, Fahrenheit (standard in the
US) or Celsius (standard outside the US). To switch your temperature preference, go to Settings >
Temperature alarm.
+ Make sure you’ve set the right kind of temperature alert—for example, if you want to make sure
your baby’s room does not get below 68 degrees Fahrenheit, set the Low Temperature Alert to 68.
If you want to make sure your baby’s room doesn’t get above a certain temperature, set the High
Temperature Alert to that temperature.
Motion alerts don’t work.
+ You might need to adjust the sensitivity of the alerts—for example, if Motion detection is set to Low,
the monitor will not come on as often as when Motion detection is set to Medium or High. To adjust
this setting, go to Settings > Motion detection.
+ If you have multiple cameras, you might need to set an alert for the camera you’re using—motion
alerts need to be set separately for each camera.
+ The App gives a maximum of 2 notifications every 4 minutes.
23
Sound alerts don’t work.
+ You might need to adjust the sensitivity of the alerts—for example, if Sound detection is set to Low,
the monitor will not come on as often as when Sound detection is set to High. To adjust this setting,
go to Settings > Sound detection.
+ If you have multiple cameras, you might need to set an alert for the camera you’re using—sound
alerts need to be set separately for each camera.
+ The App gives a maximum of 2 notifications every 4 minutes.
I’d like to stop sharing the camera view with a friend/family member.
+ Go to the Settings menu in the Project Nursery App on your phone/tablet and select Delete camera
at the bottom of the menu. This will stop all sharing, but you’ll need to set up the camera again on
your phone.
I’d like to give someone full access to my camera (including settings).
+ Guess accounts have limited access to settings. If you want to give someone full access, you will need
to give them your account log-in info and password (not recommended!).
I can’t access the camera from my computer.
+ The Project Nursery WiFi camera works with the Project Nursery App on iOS and Android devices
only. It does not support computers or other mobile device operating systems.
I can’t open the App on my Android tablet.
+ The Project Nursery App is not compatible with some makes and models of Android tablets. Contact
our customer service at 1-844-393-7338 to see if your Android tablet is compatible with the Project
Nursery App.
©2017 Voxx Accessories Corp.
3502 Woodview Trace, Suite 220
Indianapolis, IN 46268 PNMWIFIAC IB 05b

Navigation menu