Voxx Electronics DEI6816 Two way transceiver SST car remote starter (IVU) User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2055532
Application ID	MFRTg1s/AU9xbGk3rl+XhA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	65.95kB (824333 bits)
Date Submitted	2013-08-28 00:00:00
Date Available	2013-09-06 00:00:00
Creation Date	2013-07-16 10:24:48
Producing Software	Adobe PDF Library 9.9
Document Lastmod	2013-07-16 10:24:50
Document Title	User Manual
Document Creator	Adobe InDesign CS5.5 (7.5)

6816T
Replacement
Control Center
Product Description
Remote Pairing
The 6816T control center is compatible with the following systems: 3606,
4606, 4706, 4806, 5606, 5706, 5806. It is not compatible with
Directed legacy 434MHz ASK or SST systems.
LED
Control Center
Prepare the vehicle system to be Paired with a new remote
1. Open at least one vehicle door.
2. Turn the key to the ON position.
3. Within 5 seconds press and release the Control button on the Control
Center one time.
4. Within 5 seconds, press and hold the Control button on the Control
Center. The status LED begins flashing in single flash sequence and
the siren/horn sounds once to confirm the system is ready for remote
pairing. Release the button.
5. Locate your remote control model below and follow the instructions.
Button
System Pairing will exit if:
•
The ignition is turned off
•
The open door is closed
•
60 seconds lapses with no actions
Mounting the Control Center
Note
Once this replacement control center has been installed, all
remote controls must be paired with your system. See Remote
Pairing for details and follow the instructions for your remote
control type.
Note: Make sure the remote to be paired with the system is set for the desired Car 1 or Car 2 operation.
LCD Remote Control:
1. Press and hold the
button for 8 seconds, the remote beeps once,
button.
Main Menu is displayed. Release the
2. Press the AUX or
buttons until Pair is displayed.
3. Press and hold the
button until the remote beeps 3 times then release the
button. The remote is now ready to pair with the system.
4. Press the
button.
5. Wait several seconds for feedback as the remote generates a security
encryption and sends it to the Control Center. If pairing is successful
the siren/horn sounds and the remote emits several tones. The screen
displays if the Pairing is successful or failed with corresponding text. If
pairing fails repeat step 4.
AUX
The control center’s position should be discussed with the vehicle owner
prior to installation since the antenna, with built-in status LED and Valet/
Program, must be visible/accessible to the customer.
AUX
AUX
AUX
AUX
The best position to locate the control center is centered high on the front
windshield. It can be mounted vertically or horizontally relative to the
windshield. Metallic window tint can also affect range negatively, so this
should be a consideration when determining the mounting location.
AUX
After you determine the best mounting location, follow these steps:
Clean the mounting area with a quality glass cleaner or alcohol to remove
any dirt or residue.
To exit pairing mode on the remote:
•
Press and release the
button.
•
Wait 30 seconds without pressing a command button on the remote.
Plug the cable into the control center.
Mount the control center with double-sided tape.
Responder LE or Companion Remote Control:
1. Press and hold the
button for 8 seconds. The transmit LED will come
on solid. Release the
button.
2. Press and hold the
until the transmit LED flashes 3 times then
comes on solid.
3. Press the
button.
4. Wait several seconds for feedback as the remote generates a security
encryption and sends it to the Control Center. If pairing is successful
the siren/horn sounds and the 2-way remote emits several tones (the
companion remote does not generate tones). If pairing is not successful press and release the
button once and then repeat steps
2 and 3.
AUX
Route the cable down the window pillar to the control module and plug
the cable in the control module.
AUX
AUX
AUX
CONTROL CENTER
CABLE
AUX
AUX
To exit pairing mode on the remote:
•
Press and release the
button once, then press and hold until the
transmit LED shuts off.
•
Wait 30 seconds without pressing a command button on the remote
control.
AUX
CONTROL
MODULE
© 2013 Directed, All rights reserved.
GOVERNMENT REGULATIONS
This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,
and (2) This device must accept any interference received, including interference that may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television, which can
be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
To satisfy FCC RF exposure compliance requirements, the device and its antenna must maintain a separation distance of 20 cm or more from the person’s
body, except for the hand and wrists, to satisfy RF exposure compliance.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Les changements ou modifications non approuvés expressément par la partie responsable de la conformité pourrait annuler l’autorité de l’utilisateur à faire
fonctionner l’équipement.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.
LIMITED ONE YEAR CONSUMER WARRANTY
For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security product, Directed Electronics. (“DIRECTED”) promises to the original purchaser, to repair or replace with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the
“Part”), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased
from an authorized DIRECTED dealer; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of
sale bearing the following information: consumer’s name, address, telephone number, the authorized licensed dealer’s name and complete product and
Part description.
This warranty is nontransferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or the Part has
been damaged by accident, unreasonable use, neglect, improper service, installation or other causes not arising out of defect in materials or construction.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, EXCEPT AS STATED ABOVE, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY,
IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF
INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME
FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY
NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. DIRECTED IS NOT OFFERING A GUARANTEE OR
INSURANCE AGAINST VANDALISM, DAMAGE, OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS, AND DIRECTED HEREBY DISCLAIMS
ANY LIABILITY WHATSOEVER, INCLUDING WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE, OR VANDALISM. IN THE EVENT OF A CLAIM
OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.
CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY
CLAIM AGAINST DIRECTED SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER’S PURCHASE PRICE OF THE PART. DIRECTED SHALL
NOT BE RESPONSIBLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTAL
DAMAGES, DAMAGES FOR THE LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE.
NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR AT DIRECTED’S OPTION
THE PART AS DESCRIBED ABOVE.
This warranty only covers Parts sold within the United States of America and Canada. Parts sold outside of the United States of America or Canada are
sold “AS-IS” and shall have NO WARRANTY, express or implied. Some states do not allow limitations on how long an implied warranty will last or the
exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary
from State to State. DIRECTED does not and has not authorized any person or entity to create for it any other obligation, promise, duty or obligation in
connection with this Part. For further details relating to warranty information of Directed products, please visit the support section of DIRECTED’s website
at: www.directed.com
920-10012-01 2013-07
© 2013 Directed, All rights reserved.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.2-c003 61.141987, 2011/02/22-12:03:51
Create Date                     : 2013:07:16 10:24:48-07:00
Metadata Date                   : 2013:07:16 10:24:50-07:00
Modify Date                     : 2013:07:16 10:24:50-07:00
Creator Tool                    : Adobe InDesign CS5.5 (7.5)
Page Image Page Number          : 1, 2
Page Image Format               : JPEG, JPEG
Page Image Width                : 256, 256
Page Image Height               : 256, 256
Page Image                      : (Binary data 11084 bytes, use -b option to extract), (Binary data 10080 bytes, use -b option to extract)
Instance ID                     : uuid:62e8b74d-38bf-429e-ba47-f47b3b995ab2
Document ID                     : xmp.did:381DC63E3CEEE2118690D5534671193F
Original Document ID            : adobe:docid:indd:28d5e7a3-c3ca-11de-8930-b02fd2093fb0
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:93E7D4DF3BEEE2118690D5534671193F
Derived From Document ID        : adobe:docid:indd:28d5e7a3-c3ca-11de-8930-b02fd2093fb0
Derived From Original Document ID: adobe:docid:indd:28d5e7a3-c3ca-11de-8930-b02fd2093fb0
Derived From Rendition Class    : default
History Action                  : saved, saved, saved, saved, saved, saved, saved
History Instance ID             : xmp.iid:94A4243655EDE211811FEE216D32CA83, xmp.iid:95A4243655EDE211811FEE216D32CA83, xmp.iid:284608CD5FEDE211811FEE216D32CA83, xmp.iid:23713966A0EDE211811FEE216D32CA83, xmp.iid:93E7D4DF3BEEE2118690D5534671193F, xmp.iid:381DC63E3CEEE2118690D5534671193F, xmp.iid:501262963CEEE2118690D5534671193F
History When                    : 2013:07:15 06:48:21-07:00, 2013:07:15 06:48:21-07:00, 2013:07:15 08:04:09-07:00, 2013:07:15 15:46:34-07:00, 2013:07:16 10:22:09-07:00, 2013:07:16 10:22:09-07:00, 2013:07:16 10:24:36-07:00
History Software Agent          : Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5, Adobe InDesign 7.5
History Changed                 : /;/metadata, /metadata, /;/metadata, /;/metadata, /metadata, /;/metadata, /;/metadata
Doc Change Count                : 671
Format                          : application/pdf
Producer                        : Adobe PDF Library 9.9
Trapped                         : False
Page Count                      : 2
Creator                         : Adobe InDesign CS5.5 (7.5)

EXIF Metadata provided by EXIF.tools