Voxx Electronics NAH2503 5 Buttons OOK Remote User Manual
DEI Headquarters, Inc. 5 Buttons OOK Remote
User Manual
DOC: 1.00 - AS-2775 - - May 28, 2008 - - MO - Assembled in Canada
5-BUTTON
AUTOMATIC / MANUAL TRANSMISSION
REMOTE STARTER
AS-2775
User Guide
WARNING
It is the responsibility of the vehicle operator to ensure that their
vehicle is parked in a safe and responsible manner.
1. a) Manual transmission: When leaving the vehicle, it is the user’s
responsibility to ensure that the gearshift lever is in the NEUTRAL
position and the parking brake is engaged in order to avoid accidents
upon remote starting.
b) Automatic transmission: When leaving the vehicle, it is the user’s
responsibility to ensure that the gearshift lever is in “Park” in order to
avoid accidents upon remote starting.
(Note: Make sure that the automatic vehicle cannot start in "Drive".)
2. It is the user's responsibility to ensure that the remote starter is disabled
or put into valet mode before servicing.
FCC USER NOTICE (U.S.A.):
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to
this equipment. Such modifications could void the user's authority to operate the equipment.
P. 2 User Guide
Table of Contents
Introduction ............................................................ 2
Using the Remote Control..................................... 3
Vehicle Presets....................................................... 3
Heater & Heated Seat......................................... 3
Windshield Wipers, Radio & Headlights ............. 3
Arming the Starter Kill........................................... 3
Remote-Starting Your Vehicle .............................. 4
Setting Your Vehicle Into Ready Mode............... 4
Remote-starting................................................... 5
Driving Off ........................................................... 5
Remote Starter Features ....................................... 5
Idle Mode............................................................. 5
Valet Mode .......................................................... 6
Panic Mode ......................................................... 7
Quick LockoutTM .................................................. 7
Cold Weather Mode ............................................ 7
The Starter Kill and the Anti-grind Feature ......... 8
Extended Run Time ............................................ 8
Advanced Features: Installation-programmable
Options.................................................................... 8
Passive or Active Arming of the Starter Kill ........ 8
OEM-Style Alarm ................................................ 8
Remote Door Locks ............................................ 9
Priority Door Access............................................ 9
Ignition-controlled Door Locks ............................ 9
Ignition Relock..................................................... 9
Secure Lock ........................................................ 9
Remote Trunk Release ....................................... 9
Safe Start ............................................................ 9
Installer-Programmable Valet Mode ................... 9
“Home Valet™” Mode .................................... 9
Turbo Mode....................................................... 10
Engine Run Time .............................................. 10
Constant While Pressed ................................... 10
Horn Chirp Timing ............................................. 11
Multi-car Operation............................................ 11
Troubleshooting Poor Transmitting Range ...... 11
LIMITED LIFETIME WARRANTY ......................... 12
Introduction
This is a state-of-the-art remote car starter system. The system is packed with advanced features
such as priority access to the driver’s door (commodity features) and the Safe Start children safety
feature.
With many advanced functions, this product will satisfy any one of your expectations from high-end
commodity and security systems, without neglecting any standard feature commonly offered by
entry-level starters.
User guide P. 3
Using the Remote Control
Your Remote Car Starter is equipped with a 5-button multi-channel remote control. It can operate
two independent vehicles equipped with a Remote Car Starter (see Multi-Car Operation section,
later in this Guide, for second-car transmitter functions).
The functions of the transmitter are as follows:
Picture serves as example only.
N.B.: Pressing the LOCK and UNLOCK buttons simultaneously will activate the AUX 2 output.
Vehicle Presets
Heater & Heated Seat
When leaving the vehicle it is recommended to preset the accessory controls in preparation for the
next remote start. Settings for the blower motor (fan), front and rear, as well as heated seats (if
equipped) should not be left on HIGH. It is recommended to leave the settings on LOW or MEDIUM
instead.
Windshield Wipers, Radio & Headlights
Certain vehicles require the radio and / or windshield wipers and / or headlights circuits to become
energized while running under remote start. When leaving the vehicle you must ensure that the
windshield wipers and headlights switches are OFF. Leaving the headlights switch ON on certain
types of vehicles could cause them to remain ON even after remote starter shutdown, resulting in a
dead battery.
Arming the Starter Kill
The Starter Kill (if installed) can be configured by the installer either to Passive Mode (so as to arm
automatically) or Active Mode (so as to require the user’s intervention for arming). By default, your
Remote Car Starter is configured to Passive Mode.
¾ Passive mode:
• To arm the Starter Kill, press the LOCK button on the transmitter, OR
• In Passive Mode, the Starter Kill will also automatically arm 1 minute (by default) or 3 minutes
(if configured this way) after the ignition is turned OFF or once the last door is closed (if the
doors are monitored).
- The LED on the antenna will flash quickly during the countdown preceding the
activation of the Starter Kill.
LOCK: Locks the doors and arms
the STARTER KILL.
TRUNK: Opens the TRUNK or
activates the AUX 3 output
STOP: Stops the engine if pressed
for less than 3 seconds or triggers
Panic mode if pressed for more than
3 seconds.
UNLOCK: Unlocks the doors
and disarms the STARTER
KILL. Activates the AUX 1
output if priority door access
is configured.
START: Remote starts the
engine or gets the system
into Cold Weather mode if
pressed for 3 seconds.
P. 4 User Guide
- Once the activation countdown expires, the LED will send a series of quick double
flashes to indicate that the Starter Kill is now armed.
• To disarm the Starter Kill, press the UNLOCK button on the transmitter.
- The Starter Kill will automatically rearm itself after 1 minute (by default) or 3 minutes
(if configured this way) if no door is left opened (if the doors are monitored) and the
ignition is not turned ON.
¾ Active Mode:
• To arm the Starter Kill, press the LOCK button on the transmitter.
- The parking lights will flash once.
- The LED on the antenna will flash slowly.
- If remote door locks are installed, this will also lock the doors and arm the OEM-style
alarm.
• To disarm the Starter Kill, press the UNLOCK button on the transmitter.
- The parking lights will flash twice.
- The LED on the antenna will remain OUT.
- If remote door locks are installed, this will also unlock the doors.
Remote-Starting Your Vehicle
If your vehicle has an automatic transmission, simply press the START button to remote start or
stop your vehicle. Skip the next steps on to “Remote-starting”.
Setting Your Vehicle Into Ready Mode
If your vehicle has a manual transmission you must read the following indications. In order to
start the vehicle by remote, the unit must first be set to Ready Mode. If the unit is not set to Ready
Mode, it cannot remote start the vehicle.
Please note that Ready Mode can be enabled by the remote or the handbrake, depending on
the option that was selected by your installer. Therefore, you must follow the appropriate
procedure between the two described below in order to set your vehicle into Ready Mode.
Once the system is set to Ready Mode, the vehicle can be remote started and stopped at any time.
The system will exit Ready Mode if a door, the hood or the trunk is opened, if the brake pedal is
pressed, if the parking brake is disengaged or if the ignition key is turned to the IGNITION ON (RUN)
position.
To set the system to Ready Mode:
If Ready Mode is enabled by remote If Ready Mode is enabled by handbrake
1. Ensure that all the doors, hood and trunk are closed. Make sure that the gear selector is in the
neutral position.
2. With the engine already running, apply the
parking brake once and release the brake
pedal.
Make sure to release the brake pedal.
2. With the engine already running, apply the
parking brake twice and release the brake
pedal.
Make sure to release the brake pedal.
The parking lights will flash 3 times
quickly and remain lit.
Skip to step 4.
3. Within 20 sec. of engaging the parking
brake, press and hold LOCK, UNLOCK or
START on the transmitter.
The parking lights will flash 3 times
quickly and remain lit.
-
4. Remove the key: the engine will continue running.
5. Exit the vehicle and close all doors, hood and trunk.
User guide P. 5
6. Press for approx. 1 second either:
a. LOCK to lock the doors and shut down the engine;
b. UNLOCK to unlock the doors and shut down the engine;
c. START to shut down the engine without affecting the doors.
Note: The vehicle will also enter Ready Mode once the engine run time expires.
Remote-starting
Press the START button for approximately 1 second. The parking lights will come ON to inform you
that the Remote Car Starter has received your signal. Approximately 5 seconds later, the engine
will start. The parking lights will remain ON during the pre-programmed run time of the engine.
If the vehicle does not start at the first attempt, the system will shut down, wait a few seconds and
try to start the engine again. If your vehicle is equipped with an automatic transmission, there will
be 3 start attempts before the system gives up.
Driving Off
With the vehicle running under remote control, press the UNLOCK button to disarm the Starter Kill
and/or the OEM-style alarm (if installed) and unlock the doors. Enter the vehicle and do the
following:
1. Turn the ignition key to the IGNITION ON (RUN) position. (Do not turn the key to the CRANK
position while the engine is running. This would cause the starter motor to re-engage.)
2. Press the brake pedal to disengage the remote starter unit.
You are now ready to drive off.
Remote Starter Features
Idle Mode
Convenience feature: Idle Mode allows you to keep the engine running and the doors
locked while you stop, for example, at a convenience store or for a short delivery.
This feature allows you to let the remote starter take over control of the vehicle (i.e. no Key in the
Ignition Switch) while the engine is running.
If your vehicle has an automatic transmission, proceed as follows to set the system to Idle
Mode:
1. With the engine running, make sure to release the brake pedal and press the LOCK, UNLOCK or
START button on the transmitter until the parking lights come ON.
2. Remove the ignition key from the ignition switch.
The engine will continue running.
3. Exit the vehicle and close all doors, hood and trunk.
4. Press the LOCK button to leave the doors locked.
This will also arm the OEM-style alarm and starter kill (if configured|).
5. Press the UNLOCK button to leave the doors unlocked.
Note: The engine will continue running until the user re-enters the vehicle or until the expiration of
the engine run time.
If your vehicle has a manual transmission, Idle Mode can be activated through the same
routine as that used for Ready Mode (see earlier in this Guide); at the last step, the TRUNK
button is pressed instead of the other buttons.
Please note that the horn will honk once and that the OEM-style alarm will be armed if the
Idle Mode option is enabled.
P. 6 User Guide
Note: If the pre-programmed run-time expires or if the user shuts down the engine by remote
control, the vehicle will enter Ready Mode.
Caution!!! Do not leave children or pets unattended in a vehicle standing in Idle Mode.
Valet Mode
When your vehicle is in Valet Mode, the remote starter and alarm (if configured) functionalities are
disabled. If the vehicle needs to be serviced, or if you park it indoors, the Valet Mode will prevent
the engine from being remote-started accidentally.
¾ Any of the following features will put your remote car starter into Valet Mode:
• Ignition Valet: This feature allows you to put your system into Valet Mode by
using the ignition key.
• Remote valet: This feature allows you to put your system into Valet Mode by
using the transmitter.
• Valet switch: This feature allows you to put your system into Valet Mode by using a
push button switch (optional).
To put the system i n t o Valet Mode
• To put the system i n t o Valet mode using the KEY (Ignition Valet Mode):
a. Insert the ignition key into the ignition switch. Within 10 sec., turn the key 5 times
successively into the IGNITION/RUN and OFF positions.
The parking lights will flash three times.
b. Turn the ignition OFF
The LED on the antenna will come ON solid to indicate that the vehicle has
successfully entered Valet mode.
• To put the system i n t o Valet mode using the TRANSMITTER (Remote Valet Mode):
a. Press the UNLOCK and START buttons simultaneously until the parking lights flash
three times.
The LED on the antenna will come ON solid to indicate that the vehicle has
successfully entered Valet mode.
• To put the system i n t o Valet mode using the PUSH BUTTON SWITCH (Valet Switch
Mode):
a. Insert the ignition key into the ignition switch.
b. Turn the key into the ON position
c. Within 5 seconds, press the push button switch until the parking lights flash 3 times.
d. Release the push button and turn the ignition to the OFF position.
The LED on the antenna will come ON solid to indicate that the vehicle has
successfully entered Valet mode.
To put the system o u t o f Valet Mode
• To put the system o u t o f Valet mode using the KEY (Ignition Valet Mode):
a. Insert the ignition key into the ignition switch. Within 10 sec., turn the key 5 times
successively into the IGNITION/RUN and OFF positions.
The parking lights will flash twice.
b. Turn the ignition OFF
The LED on the antenna will flash quickly to indicate that the vehicle is now out of
Valet mode.
• To put the system o u t o f Valet mode using the TRANSMITTER (Remote Valet Mode):
a. Press the UNLOCK and START buttons simultaneously until the parking lights flash
twice.
The LED on the antenna will flash quickly to indicate that the vehicle is now out of
Valet mode.
User guide P. 7
• To put the system o u t o f Valet mode using the PUSH BUTTON SWITCH (Valet Switch
Mode):
a. Insert the ignition key into the ignition switch.
b. Turn the key into the ON position
c. Press the push button switch until the Parking lights flash twice.
d. Release the push button and turn the ignition to the OFF position.
The LED on the antenna will flash quickly to indicate that the vehicle is now out of
Valet mode.
Panic Mode
Note: Panic mode can only be activated if the horn has been adequately configured by your
installer.
In an emergency situation, you can activate panic mode by pressing and holding the STOP button
for more than 3 seconds, until the horn starts honking. If the vehicle is under a remote start, the
engine will shutdown automatically before setting off the horn. You can stop the horn by pressing:
(this will lock your doors and deactivate panic mode), or
(this will unlock your doors and deactivate panic mode).
Furthermore, the panic mode can be stopped by activating one of the following three (3) features:
a) Remote valet (pressing UNLOCK and START for at least 3 seconds)
b) Ignition valet (turning the key inside the ignition switch from OFF to ON 6 times in a row)
c) By turning the key to the ON position and pressing the valet switch (if included) until the
parking lights flash 5 times.
Panic Mode will automatically shut down after 30 sec.
Quick LockoutTM
(Also called Secure Panic.) For fast protection in emergency situations, the system will LOCK all
doors when you press the brake pedal while you hear the sound signal. (Quick Lockout is
only available when panic mode has been set off.)
Cold Weather Mode
If your vehicle has a manual transmission, Ready mode should be set before entering Cold
Weather mode. When Cold Weather Mode is active, the engine starts every 2 hours and runs for 3
minutes (or for 8 or 20 minutes with diesel engines). Cold Weather Mode automatically ends after
24 hours (or 12 starts).
To enter Cold Weather Mode:
• Press and hold the START button for at least 3 seconds
• The parking lights will flash for 2 seconds, pause, then flash three (3) times.
To exit Cold Weather Mode, do any one of the following actions:
• Open the hood.
• Start the engine by remote.
• Turn the ignition key to the IGNITION ON (RUN) position.
• Press and hold the START button until the parking lights come ON for 2 seconds, pause,
then flash once.
If Safe Start is enabled, you can activate Cold Weather Mode by:
• Pressing and releasing the START button, then;
• Pressing and holding the START button until the parking lights flash 3 times.
To verify whether the system is in Cold Weather Mode (automatic transmissions only):
• Press the brake pedal:
P. 8 User Guide
• If the vehicle is in cold weather mode, the parking lights will remain ON while the
brake pedal is pressed.
The Starter Kill and the Anti-grind Feature
With this added security feature, the system will prevent your vehicle from starting with the ignition
key when the Starter Kill is armed. If your Remote Car Starter was installed with the Starter Kill
option, one will not be able to start your vehicle with the key unless the system has been unlocked
and disarmed first, or put into Valet Mode.
Note: If the Starter Kill is installed, your vehicle will benefit from a protection against starter
motor damage that could occur after remote-starting the engine should the user, by force of
habit, turn the ignition key to the CRANK position.
Extended Run Time
With the vehicle running under a remote start, pressing and holding the START button for more than
3 seconds will reset the run time counter to zero and restart the run time cycle from the beginning.
• The horn (if programmed) will honk once;
• The parking lights will flash slowly 3 times then remain lit.
To stop the vehicle at any moment, simply press the STOP button. This procedure can only be
carried out once per remote start.
Example: If your Module is programmed for a runtime of 3 minutes and your vehicle has been
running for 2 minutes already, pressing the START button will reset the counter to zero and the
Engine will run for another cycle (in this case, 3 minutes).
Advanced Features: Installation-programmable Options
The Remote Car Starter was designed with flexibility and OEM integration in mind. With its
programmable options, this unit can single-handedly control nearly any electrical system in your
vehicle.
Caution: The programming of your system should be left to a professional. Changing any
one of the settings may affect the operation of your Remote Car Starter. Please note that the
following programmable options may require additional parts and labor.
Passive or Active Arming of the Starter Kill
See section “Arming the Starting Kill” earlier in this guide.
OEM-Style Alarm
The OEM-style alarm (if configured by your installer) monitors the doors, hood and ignition switch
of your vehicle. It will sound the horn if a door or the hood is opened, or if the key is turned in the
ignition.
• To arm the OEM-style alarm, press the LOCK button on the transmitter.
- The OEM-style alarm will ONLY arm if the LOCK button on the transmitter is pressed.
- The LED on the antenna will flash slowly to indicate that the OEM-style alarm is now
armed.
• To disarm the OEM-style alarm, press the UNLOCK button on the transmitter.
- To stop the horn from sounding if the OEM-style alarm is triggered, press the LOCK or
UNLOCK button, or put the system in and out of Valet Mode (ignition valet, remote valet or
using the valet switch – for more information, see the “Valet Mode” section earlier in
this Guide).
User guide P. 9
Remote Door Locks
If your Remote Car Starter was installed with the Remote Door Locks option, you will have the
convenience of remote keyless entry. See section “Arming the Starter Kill”, earlier in this Guide,
for further instructions on remote door locking and unlocking.
Priority Door Access
If the Remote Door Locks option is installed on your vehicle, this safety feature allows you to
unlock solely the driver’s door with a single press of the UNLOCK button on the transmitter; upon a
second press of the UNLOCK button within 6 seconds, all the other doors will unlock.
Ignition-controlled Door Locks
This is an added security feature. If your Remote Car Starter was installed with the Ignition-
Controlled Door Locks option, the doors will automatically be locked as soon as the ignition key is
turned to the IGNITION ON (RUN) position while the brakes are pressed. The remote car starter will
also lock any door that was unlocked and opened (then closed) the next time the break pedal is
pressed. When the key is turned to the OFF position, the doors will automatically be unlocked.
Ignition Relock
On Remote Car Starters of this series, when Ignition-controlled Door Locks are enabled and the
ignition key is in the IGNITION ON (RUN) position, should any door be unlocked and opened, all doors
will be relocked next time the brake pedal is pressed.
Secure Lock
(Disabled by default.) Before your vehicle can be remote-started, the factory security system must
first be disarmed. The Secure Lock feature may be required on certain vehicle models with factory
security systems that automatically unlock the doors when the security system is disarmed.
To keep your vehicle protected when the factory security system is disarmed for a remote start,
Secure Lock will relock your doors as soon as the vehicle is started. Once the engine is shut down
by remote or after its runtime has expired, Secure Lock will also rearm your factory security system
and relock the doors.
Remote Trunk Release
If your system was installed with the Remote Trunk Release option, you can open your trunk by
pressing the TRUNK button for 3 seconds on the remote transmitter. The OEM alarm will be
disarmed until the LOCK button is pressed.
Safe Start
If this feature is enabled, the user must press the START button twice within 3 seconds to remote-
start the vehicle. This will eliminate accidental remote starts, e.g. when children are playing with the
transmitter.
• To remote-start your vehicle if Swap Start Mode is selected, press LOCK and UNLOCK
simultaneously.
• The AUX 2 output can be activated by pressing the START button.
Installer-Programmable Valet Mode
“Home Valet™” Mode
If configured at installation, this feature will set the vehicle to a no-remote-start mode: if the vehicle
is parked indoors, there is no danger of it starting accidentally by remote control.
Note: Once the home valet mode is activated, the vehicle will not start by remote but the
OEM alarm functions and starter kill will still be enabled.
To take the system i n t o home valet mode:
• Press the LOCK or UNLOCK button.
• Within 3 seconds, press the START and LOCK buttons simultaneously.
P. 10 User Guide
The parking lights will come ON for 2 seconds, then turn OFF.
To take the system o u t o f home valet mode:
• Turn the ignition key to the IGNITION ON (RUN) position.
The system will warn you if someone attempts to start your vehicle while it stands in Home Valet
Mode:
• The parking lights will:
Turn ON then OFF; then
Flash twice, pause; then
Flash twice again.
Turbo Mode
If Turbo Mode is configured at installation, it will allow a turbocharger to idle down after the user
leaves the vehicle: the unit will take over the vehicle and keep it running for 60 seconds (or until it
is shut down by remote control), then shut down the engine.
If your vehicle has an automatic transmission, proceed as follows to set the system to
Turbo Mode:
1) With the engine running, make sure to release the brake pedal and press the LOCK, UNLOCK or
START button on the transmitter until the parking lights come ON.
2) Remove the ignition key from the ignition switch.
The engine will continue running.
3) Exit the vehicle and close all doors, hood and trunk.
4) Press the TRUNK button; this will lock the doors, arm the OEM-style alarm (if
configured|) and confirm that the vehicle is in Turbo Mode.
5) The engine will shut down after 60 seconds.
If your vehicle has a manual transmission, follow all steps of the Ready Mode routine (see
earlier in this Guide) to activate Turbo Mode. At the last step, press either:
1) LOCK to lock the doors and have the engine shut down after 60 seconds;
The parking lights will flash 3 times and remain lit.
The OEM-style alarm and starter kill (if configured) will be armed.
2) UNLOCK to unlock the doors and have the engine shut down after 60 seconds;
The parking lights will flash 3 times and remain lit.
3) STOP to shut down the engine without affecting the doors.
Note: The vehicle will enter Ready Mode once the engine run time expires.
Engine Run Time
If you have a gas engine, your Remote Car Starter can be programmed to run the engine for 3, 15,
or 25 minutes (15 minutes by default). If you have a diesel engine, the Remote Car Starter can be
programmed to run the engine for 8, 20, or 30 minutes (20 minutes default).
Constant While Pressed
If enabled by your installer, this option allows you to open or close your windows at a distance or to
open or close the sunroof.
• Pressing and holding the LOCK button for more than 3 seconds will lock all doors and will send a
constant pulse as long as the LOCK button is held down (maximum of 15 seconds). This
constant pulse can be configured to activate certain functionalities such as rolling up the
windows – Please refer to your installer to see if your vehicle is compatible with this
option.
• Pressing and holding the UNLOCK button for more than 3 seconds will unlock all doors and will
send a constant pulse as long as the UNLOCK button is held down (maximum of 15 seconds).
This constant pulse can be configured to activate certain functionalities such as rolling down the
User guide P. 11
windows – Please refer to your installer to see if your vehicle is compatible with this
option.
Horn Chirp Timing
The pulse duration can be configured by your installer (from 5 ms to 200 ms).
Multi-car Operation
This option allows the owner of two vehicles, both equipped with the same Remote Car Starter
model, to control both systems with a single remote control. To control the second vehicle,
simultaneously press the TRUNK button and the button of the function you wish to use.
Note: Your remote control must be configured for second car operation by the installer.
Press TRUNK + LOCK buttons simultaneously: .......LOCK
Press TRUNK + UNLOCK simultaneously:.................UNLOCK
Press TRUNK + START simultaneously: ...................START
Press TRUNK + STOP simultaneously: .....................STOP
Press TRUNK + START simultaneously for 3 sec:.....Cold Weather Mode
Troubleshooting Poor Transmitting Range
Many factors may affect the operating range of the transmitter. Some of these are:
• The condition of the battery in the transmitter.
• The operating environment (for example: downtown radio-frequency noise, airports, cellular
phone towers…).
• Metal: any type of metal will affect operating range. This includes the vehicle itself.
• The shape of the vehicle can affect range as well (vans in general have less range).
• The shape of the roof and A-pillars brings about considerable radio-frequency deflection (in
this case, the signal from the remote control). As a result, the direction in which the vehicle is
facing in relation to the remote control can affect the range. Straight on (standing in front of
the vehicle) generally gives you the greatest range; the second best performance is from the
back. Using the remote control from either side of the vehicle will usually give the lowest
range.
• The range will be significantly lower in a crowded parking lot than in open space.
• Always hold the transmitter high, approximately at shoulder height.
• The operating range will be somewhat lower on vehicles equipped with an aftermarket or
factory alarm.
P. 12 User Guide
LIMITED LIFETIME WARRANTY
REMOTE STARTERS AND ALARM SYSTEMS:
As the manufacturer, 4366859 Canada Inc. (“Autostart”) warrants to the original consumer purchaser only
(nontransferable) that the remote starter module (control box) shall be free from defects in materials and
workmanship for as long as the original consumer purchaser continuously owns the vehicle in which the
remote starter was originally installed, as specified below:
1) For the first two years after the date of manufacture, as specified by the serial number on the module,
Autostart will replace the remote starter module free of charge with a new remote starter module.
2) For the third year and any consecutive year after the date of manufacture, as specified by the serial
number on the module, Autostart will provide to the original consumer purchaser a new remote starter
module, for a repair charge of $25.00 USD.
In all cases, the consumer must return the remote starter module to the point of purchase, and must provide a copy
of the proof of purchase to said retailer. A remote starter module will be returned to the retailer for the consumer to
claim within a 4 (four)-week period. For case (2), a certified check or money order in the amount of $25.00 USD
must accompany the remote starter module, or the retailer may refuse the return.
ACCESSORIES:
Autostart warrants to the original consumer purchaser only (nontransferable) that it will replace any Autostart
accessory part for a one-year period from date of purchase. Accessories will only be replaced if proven defective in
material or workmanship, and if, when the accessory is returned to the point of purchase, the retailer is provided
with a copy of the proof of purchase. The accessory will be sent to the retailer for the consumer to claim within a 4
(four)-week period.
THE WARRANTY IS VOID IF:
1) The product has been damaged, altered in any way or tampered with, without the explicit written
consent of an Autostart technician. For remote starter modules, this includes the opening or
removal of the plastic covering of the module, or the removal or alteration of the barcode label on
the plastic covering of the module.
2) The product is damaged due to accident, fire, flood, shipping and handling, misuse, neglect, or
3) The product has been installed or repaired by anyone other than a certified technician.
4) The product has been improperly installed or used.
THE WARRANTY DOES NOT COVER:
1) Batteries.
2) Scratched or worn transmitter cases.
3) Installation and/or removal charges for all remote starter modules and accessories.
4) Shipping and handling charges incurred for product exchange or replacement.
5) Any material damages other than to the product itself.
6) Harnessing, L.E.D. lights, switches, inverters, relays, etc.
THIS LIMITED LIFETIME WARRANTY SHALL CONSTITUTE THE SOLE LIABILITY OF AUTOSTART
FOR OUR PRODUCTS, AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED.
THERE ARE NO WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. NO PERSON, FIRM OR CORPORATION IS AUTHORIZED TO ASSUME FOR AUTOSTART
ANY OTHER LIABILITY WITH RESPECT TO THE SALE OR USE OF OUR PRODUCTS. AUTOSTART’S
LIABILITY, WHETHER BASED ON CONTRACT, TORT, WARRANTY, STRICT LIABILITY, OR ANY
OTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT FOR
DAMAGE IS THE BASIS OF THE CLAIM. UNDER NO CIRCUMSTANCE WILL AUTOSTART, ITS
DISTRIBUTORS OR THEIR AGENTS BEAR ANY LIABILITY WHATSOEVER FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
The parties hereto elect that any dispute regarding the present document be submitted to the appropriate
Court located in the Province of Quebec, District of Montreal. The parties hereto agree that this document is
governed by and interpreted in accordance with the law of Quebec. If the purchaser is located in a province
of Canada other than Quebec, all matters dealing with the warranty of quality will be governed by and
interpreted in accordance with the law of Ontario. If the purchaser is located outside Canada, all matters
dealing with the warranty of quality will be governed by and interpreted in accordance with the United
Nations Convention on Contracts for the International Sale of Goods (the “Vienna Convention”).