W Link Systems WEN-2012 Wireless LAN PC Card User Manual 0809
W-Link Systems Inc. Wireless LAN PC Card 0809
users manual
- 1 -
W-Link
WN-2012 Wireless LAN PC Card
User’s Guide
- 2 -
Introduction
This User Guide is to guide you to install a Wireless LAN designed for both large and small business
and SOHO environments and let you share a local printer and files, access internet, and roam about
different working places. The attached drivers and utilities support for Windows 95 (OSR2),
Windows 98, and Windows 2000, NT4.0 and Windows Millennium.
Package Contents
Ÿ W-Link WN-2012 Wireless LAN PC Card
Ÿ W-Link Wireless LAN CD-ROM with drivers and utilities
Ÿ User’s Guide
Ÿ Quick Start Guide
Ÿ Warranty Card
Planning your Wireless LAN
There are two usage modes for Wireless LAN, Ad-hoc mode and Infrastructure mode. Please review
your need and build your Wireless LAN.
Ad-hoc Networking
Ad-hoc network also is called Peer-to-Peer network. Without Access Point, notebook users with
W-Link WN-2012 Wireless LAN PC card can build a Ad-hoc Peer-to-Peer wireless networks to
share files with each other, share a public office printer and other peripheral resources, and even
access the Internet via a modem.
Infrastructure Networking
802.11b-compatible Access Point is a bridge or router for connect to the wired Ethernet network and
wireless network. Through the deployment of Access Point, wireless LAN can be extended to the
reach of a wired network. Therefore, A notebook user with W-Link WN-2012 Wireless LAN PC
Card can access to fixed local network resources.
- 3 -
Installation
Installation for Windows 95, Windows 98 and Windows 2000
Before installing the driver, you will need a copy of the operating system installation media, usually
a CD supplied with your computer or operating system.
On Windows 98 systems, the installation files are sometimes archived on the hard disk in
C:\WINDOWS\OPTIONS\CABS. On Windows 2000 systems, the system may prompt you to load
operating system files from the Windows 2000 installation disk. Installation under Windows 95 is
identical to the procedure given above for Windows 98 and Windows 2000. Only Windows 95
OSR2 or higher is supported.
The Setup program also installs Configuration Utility in the WN-2012 Wireless LAN PC Card in the
Program directory. This configuration utility can help you to understand and maintain your Wireless
LAN.
Install Driver
Step 1: Turn on your computer.
Step 2: Insert the W-Link WN-2012 Wireless LAN PC Card into the PC Card slot. Align the card
properly before putting it in the slot. Insert the card firmly without forcing until it seats snugly.
CAUTION: Forcing a misaligned card into the slot can damage the computer or the card.
Step 3: Windows finds a new hardware shown DLINK-DW650 and asks for the driver of WN-2012
Wireless PC Card. The driver installation wizard guides you through the steps standard for your
operating system.
Step 4: You will be asked to supply CDs or directory path information for the driver. This driver
shall be located in the following directory.
D:\DW650\ (if D:\ is your CD-ROM drive)
Step 5: Windows finds the driver described as W-Link WN-2012 Wireless LAN PC Card. Follow the
directions of Windows dialog boxes to complete the driver installation. After completing the
installation, Windows dialog will display Systems Setting Change and ask to restart the notebook.
Please click Yes to reboot the computer.
- 4 -
Install Configuration Utility
1. Restart the computer and ensure W-Link Wireless LAN Configuration Utility CD in the
CD-ROM drive.
You can run the program manually by selecting Run from the Start menu and running
SETUP.EXE from the CD-ROM drive.
D:\DW650\SETUP.EXE (if D:\ is your CD-ROM drive)
2. On the W-Link WN-2012 Wireless LAN PC Card – Installation screen, click next to start
software installation. Read the information in the Welcome dialog box and click Next. Then,
click Yes if you accept the Software License Agreement.
3. Enter the name of the Wireless LAN Service Set of the wireless network (SSID) to which your
computer will connect. The name you enter here must match exactly the name assigned to the
access point. Characters, capitalization, and spacing must be exactly identical.
NOTE: If the access point you wish to associate with has encryption active, you must also
enable encryption on the wireless client. Click Encryption in the Configuration Utilities after
reboot to go to screens where you can enable and configure encryption. You must set the
wireless client for the same Encryption algorithm and Key values as the access point it will
associate with. Refer to the Advanced Configuration section for more details about configuring
encryption
4. Select which network mode is suitable for your Wireless LAN. Infrastructure Mode is default
selection. This setting can be changed at any time after installation completion.
5. Accept the default program folder or select where the SETUP.exe stores the Configuration
Utility.
6. Select “Yes, I want to restart my computer now”. Reboot your computer by clicking Finish.
Operation
Orienting the Antenna
The PC Card antenna is attached to the end of the PC Card. For best use of the antenna:
l Keep the area around the antenna clear from materials that could block or obstruct radio
transmission, such as metal objects, electronic devices, cordless telephones, and microwave
oven.
- 5 -
l If necessary, move your notebook computer a few inches to find a better signal. Environmental
condition varies with users’ location, a difference of one or two inches can mean the difference
between a strong and a weak signal. Even a slight change in PC orientation can improve a
wireless connection.
l If you have installed the Configuration Utility, you may use the Signal Strength display in the
Link Info to determine the best location and orientation for a wireless network connection.
LED Indication
The yellow LED of Wireless LAN PC Card performs identical functions when indicating the
operational status of the card.
Advanced Configuration
Configuration
Mode (Network Mode)
1. Ad-Hoc: The Ad-Hoc network is also known as a peer-to-peer network. An Ad-Hoc networking
do not need Access Point. Instead, the Ad-Hoc network is a loose association of wireless
computers that can communicate with each other using Wireless LAN PC Card in Ad-Hoc
Mode
2. Infrastructure: In a wireless infrastructure network, wireless stations communicate with an
Access Point to connect to a wired network. An infrastructure network also can consist of
multiple Access Points. This can extend the coverage area of wireless network. In this
configuration, the wireless network consists of cells. Each cell is a single Access Point that has
different frequency channel to prevent from interference each other. A wireless station can move
from one Access Point to another without losing the network connection.
SSID
The SSID is the name of wireless network for Ad-Hoc or Infrastructure mode. To add a Wireless
LAN PC Card to an existing wireless network, configure this one with the name of the wireless
network
Tx Rate
The Fixed 1, 2, 5.5, 11Mb/s or Fully Auto transmit rates can be selected for Wireless LAN Card.
Basically, the Fully Auto setting can allow the PC Card to automatically switch to a higher Tx rate
for better throughput in most environment. A fixed rate setting does not allow PC Card to re-transmit
at a lower rate even as a result of many retransmissions.
- 6 -
PS Mode (Power Saving Mode)
Enabling power saving mode can extend the battery life of the mobile notebook by allowing the PC
Card to sleep to minimize the power consumption.
Channel
W-Link WN-2012 Wireless LAN PC Card can support up to 14 channels. But, the number of
available channels must vary in different countries and regions. The Access Point must be set to a
channel. To avoid radio interference, adjacent Access Point within the same infrastructure network
(the same SSID) should be set to different channel. The channels of Access Points must be at least
five channels apart. Instead, the Wireless LAN PC Card automatically uses the same channels as the
Access Point and roams between APs in the same wireless network.
Encryption
The Wireless LAN PC Card uses WEP encryption to protect wireless data communications.
Encryption Selection
WEP uses a combination of 40-bit keys or 128-bit keys to provide security for every data
transmission. In order to decode a data transmission, the identical WEP key must be used by each
wireless client on the network. Choose Enable or Disable to decide whether the security of wireless
network is needed or not.
Create with Passphrase
The WEP keys can be generated from a user-defined passphrase. The WEP text string is a maximum
of 32 characters.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Caution: To assure continued compliance, use only shielded interface cables when connecting computer
to peripheral devices. Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
RF Exposure Warning: This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This device’s provided external duel antennas must be installed in
accordance with provided instructions; and it must be operated with minimum 20 cm spacing
between the antennas and all person’s body (excluding extremities of hands, wrist and feet) during
wireless mode of operation. Further, this transmitter must not be co-located or operated in
conjunction with any other antenna or transmitter.
- 8 -
European Notice
Equipment with CE marking complies with the R&TTE Directive (1999/5/EC), EMC Directive
(89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the European Community.
Compliance with these directives implies conformity to the following European Norms or
Regulations (in parentheses are the equivalent international standards and regulations):
Ÿ EN 55022 (CISPR 22) – Electromagnetic Interference
Ÿ EN 50082-1 (IEC 801-2, IEC 801-3, IEC 802-4) – Electromagnetic Immunity
Ÿ EN 60950 (IEC 60950) – Product Safety
Ÿ ETS 300 326 – Technical characteristics and test conditions for data transmission equipment
operating in the 2.4GHz ISM band and using spread spectrum modulation techniques
Ÿ ETS 300 826 – Electromagnetic Compatibility (EMC) standard for 2.4GHz wide band
transmission systems and High Performance Local Area Network (HIPERLAN) equipment
This product may be used in the following EU and EFTA countries: Austria, Belgium, Denmark,
Finland, Germany, Greece, Iceland, Ireland, Italy, Liechtenstein, Luxembourg, Netherlands, Norway,
Portugal, Sweden, Switzerland and United Kingdom. Products not marked with “Not for use in
France” may be used in France.
- 9 -
Specifications
Radio Technology IEEE 802.11b Direct Sequence Spread Spectrum
Operating Frequency 2400-2483.5MHz ISM band
Modulation Schemes DQPSK, DBPSK and CCK
Channel Available 11 channels for United States
13 channels for Europe
14 channels for Japan
Data Rate 11Mbps with fall back rates of 5.5, 2 and 1Mbps
Media Access Protocol CSMA/CA with ACK
Transmitter Output Power 12.5dBm typically
Antenna Type Two External Dipole Antennas
Operating Voltage 5VDC
Interface PCMCIA Type II
Range Coverage Indoor: 35 - 100 meters (depends on environment)
Outdoor: 100 - 300 meters (depends on environment)
LED Indicator Power & Link status