WEIKING TECHNOLOGY BT06-T Bluetooth Transmitter User Manual BT06 T

SHENZHEN WEIKING TECHNOLOGY CO.,LTD Bluetooth Transmitter BT06 T

Users Manual

 Bluetooth Transmitter User Manual    Introduction ..………………………………………….……………1 1.About transmitter ………………………………………….…………1 2.System requirements…………..…….………………………………1 3.Overview……………………...………...……..………………….…1   Getting Started…..……….………………………….……….…2 1.Charging the transmitter……………………………………….…….2 2.Turning on/off the transmitter………………..………………………2 3.Pairing with Bluetooth devices……………….………………….…..3 4.LED indicator…………………………………………………….…..4   Care and maintenance…………………..……………..……...….4  FAQs…………………………...…………………………………….5  Specification…………………………………………………..……..6     Thank you for purchasing the Bluetooth Stereo Transmitter.  We hope you will enjoy this innovated high definition stereo connection product.   Please read this user’s manual carefully.
 1 Introduction   1. About Bluetooth transmitter It is a high definition bluetooth stereo transmitter. It decodes high definition stereo signals into Bluetooth digital signal. The music from your mobile phone, PC and any music devices can be transmitted wirelessly to your Bluetooth stereo receiving devices.  So you can enjoy music wireless on any stereo device without wire connection. The product has a built-in Lithium battery. The battery can last for 9-10 hours after being fully charged.  2. System requirements 1) Any audio or music playing devices with a 3.5mm audio-out jack. 2) Any Bluetooth stereo receiving device that supports Bluetooth A2DP profile, such as Bluetooth stereo headset, Bluetooth speaker, etc...   3. Overview         Getting Started 1 Multi-function button 2 Charging port 3 LED indicator 4  3.5mm audio-in plug
 21. Charging Your Device   It is recommended to charge this transmitter5 fully before first using. When the led on the transmitter is flashing RED during usage, it indicates that the battery power is low. You will need to recharge the transmitter.  To recharge your bluetooth transmitter: Step1: Connect charger or charging cable to standard power outlet; Step2: Connect the end of charger or charging cable to charging port of the transmitter. When the red LED is on, it is now charging. When the red LED is off, it has been fully charged. It takes about 2hrs to fully charge the transmitter. Remark:   1、You can recharge the transmitter to reset the device when needed. 2、Please don’t attempt to remove the battery from the transmitter.    Attention: 1、The battery is recyclable. 2、Do not dispose of the battery in fire.  2.    Turning ON/OFF the transmitter Function Operation LED indicator Turning on the transmitter  Press multi-function button for 3-5 seconds The blue LED will be ON Turning off the transmitter  Press multi-function button for 3-5 seconds The red LED will be ON for 1
 3sec. and then off 3. Pairing with Bluetooth devices Before pairing, please make sure your Bluetooth receiving devices support Bluetooth A2DP profile. Please follow the following steps: 1) Keep your transmitter and the Bluetooth stereo receiving device within 1 meter distance. 2) Switch on your Bluetooth receiving device and make it entering into pairing mode. 3) Switch on the Bluetooth transmitter. The LED will flash red and blue. It will start searching, pairing and connecting to the receiving device automatically. 4) When the connection is successful, transmitter LED will turn blue and then flashing twice every 3 seconds. 5) Connect the transmitter to your music player through 3.5mm audio jack and enjoy your music.   Remark: z The transmitter can pair with stereo Bluetooth receiving devices with PIN code: ”0000”, ”1234”, ”1111” or ”8888”. z When the transmitter is switched on every time, it will connect with the latest pairing device automatically. If you need to pair it with other devices, please switch off the old paired receiving device, and then pair the transmitter with new device.
 4z The transmitter will switch off automatically if pairing time is more than 5 minutes or disconnect with Bluetooth devices for 5 minutes.  4. LED indicator LED indicator  The status of transmitter Red and blue LEDs flash alternately  Pairing mode   Blue LED flashes twice every 3 seconds  Ready mode Red LED flashes  The battery is low     Care and maintenance Before using this transmitter, please read the following recommendations, it will help you to enjoy the product for years. z Keep the transmitter away from heat and humid. z Don’t put the product under the direct sunlight or hot areas. High temperature will shorten the life of electronic device and battery. z Don’t expose it to extreme temperature, it may damage the internal circuit board. z Don’t try to take apart the product, it may damage the product. z Don’t let it fall down to the floor or knock on hard substance, it may damage interior circuit. z Don’t use chemical or detergent to clean the product. z Don’t scrap the surface with sharp things.   Trouble Shooting: 1 Q: Why it can’t be switched on?
 5A : Please recharge it.  2 Q Why it can’t pair and connect with Bluetooth receiving devices?  A: 1) Make sure Bluetooth receiving device supports A2DP; 2) Make sure Bluetooth receiving device is placed within 1 meter; 3) Make sure Bluetooth receiving device is in pairing mode.  3 Q: Why I can’t listen to music from Bluetooth receiving devices?       A : 1)    Make sure the transmitter connect well with player;       2)  Make sure player is playing music.  Specification  Bluetooth version  Bluetooth V2.1 Bluetooth profile  A2DP Frequency response  2.4GHZ-2.4835GHZ Receiving sensitivity  -74±4dB Effective range  Up to 10m; Charging input voltage DC 5V Lithium battery  230mAH Working time  Up to 10hours Charging time  About 2hours Dimension  45*32*8mm Weight  14g
 6Federal Communications Commission (FCC) Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.   Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:     ●Reorient or relocate the receiving antenna. ●Increase the separation between the equipment and receiver.      ●Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.             ●Consult the dealer or an experienced radio/TV technician for help.
 7Warning:  Changes or modifications made to this device not expressly approved by SHENZHEN WEIKING TECHNOLOGY CO.,LTD may void the FCC authorization to operate this device.     Note:  The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

Navigation menu