WENZHOU MTLC ELECTRIC APPLIANCES ZW15RM Appliance Control User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3785972
Application ID	gvE3m1EoxtgfM+xkTwdW6A==
Document Description	user manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	190.64kB (2383006 bits)
Date Submitted	2018-03-19 00:00:00
Date Available	2018-03-19 00:00:00
Creation Date	2001-08-30 12:37:41
Producing Software	Acrobat Distiller 7.0 for Macintosh
Document Lastmod	2016-08-04 09:55:09
Document Title	user manual
Document Creator	Adobe PageMaker 6.52
Document Author:	YB

INSTALLATION INSTRUCTIONS
ZW15RM
WARNINGS AND CAUTIONS
Wireless Home Automation Control Device
Interchangeable Face Cover
In-wall Smart Meter TR
Duplex Receptacle
To be installed and/or used in accordance with appropriate electrical codes
and regulations. Exercise extreme caution when using Z-Wave devices to
control appliances. Operation of the Z-Wave device may be in a different
room than the controlled appliance, also an unintentional activation may
occur if the wrong button on the remote is pressed. Z-Wave devices may
automatically be powered on due to timed event programming.Depending
upon the appliance, these unattended or unintentional operation could
possibly result in a hazardous condition.
PLUS
Smar
er
Met
Z-Wave enabled devices should never be used to supply power to, or control
the On/Off status of medical and/or life support equipment.
SPECIFICATIONS
Voltage.............................................................................................. 120VAC, 60Hz
Incandescent..................................................................................................1000W
Electronic Ballast...................................................................................................5A
Standard Ballast............................................................................................1200VA
Resistive................................................................................................1800W(15A)
Motor.............................................................................................................. 1/2 HP
Z-Wave Frequency.............................................................................. 908.42 MHz
Operating Temperature........................................................................... 32-104° F
Range..............................................................Up to 131 feet line of sight between
the Wireless Controller and the closest Z-Wave receiver module.
FEATURES
DESCRIPTION
The ZW15RM TR Duplex Receptacle is a perfect wireless manual and remote on
/off control replacement of regular receptacles, controlling table and floor lamps,
small appliances, etc. It provides two different type outlets. One outlet with Z-Wave
mark has programmable functions such as scenes, association, schedule event,
etc. It is fully interoperable with other Z-Wave certified device from other manufacturers
and/or other applications. It can report wattage energy usage or kWh energy energy
usage to a Z-Wave gateway. It has a Blue LED on the face cover indicates the status
of the controlled outlet and/or act as a night light. The other outlet with TamperResistant feature provides constant power, helps you and your families prevent
electrical injuries.
OPERATIONS
Always-on Receptacle
Blue LED Indicator
Program Button
Smart
Meter
Smart
Meter
Z-Wave Controlled Receptacle
To replace the face
cover, just use a
flat screwdriver to
pry-off the
interchangeable plate.
If you are unsure or uncomfortable about performing the installation, please
consult a qualified electrician.
Manual Control
The program button on the ZW15RM duplex receptacle allows the user to:
INSTALLATION
1, Manually turn ON the Module: press and release the program button. The Blue
This receptacle may be used in new installations or to replace an existing wall receptacle.
WARNING : TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF THE
POWER AT THE CIRCUIT BREAKER BEFORE YOU INSTALL THIS
RECEPTACLE.
LED indicator will turn OFF,and the appliance or device plugged into Z-Wave
controlled outlet will turn ON.(Default)
2. Manually turn OFF the Module: press and release the program button. The Blue
LED indicator will turn ON, and the appliance or device plugged into Z-Wave
Perfect replacement for regular receptacles, 120VAC, 15 Amp
Wireless Z-Wave technology creates a mesh network for command and control
interoperability with other Z-Wave compliant controller and devices
Manual and Remote ON/OFF control of any connected lighting and other electrical
load for Z-Wave controlled outlet
Tamper-Resistant (TR) Receptacles keep you and your family safe
Reduce energy consumption and enjoy Wireless Home Automation
Enhance the value and technology of your condominiums and homes
Measures energy usage of any connected appliance/device
MEASURE THE ENERGY USAGE
The ZW15RM TR Duplex Receptacle enables you to measure the energy usage
of your appliance. When added to a Z-Wave network, the ZW15RM reports real
time data to your gateway or controller. It can also display actual consumption(in W)
and the accumulated power used (in kWh) in the user interface of the gateway/
remote. Please use the gateway installation manual for specific instructions on
measuring the power.
-01-
Wiring Diagram
controlled outlet will turn OFF.(Default)
Neutral
Hot
Black
White
3. When the controller is in add mode and the blue LED is blinking on the ZW15RM,
press and hold the program button of ZW15RM for 3 second, and then the controller
will verify the add.
4. When the controller is in remove mode, press and hold the program button of
ZW15RM for 3 second, and then the controller will remove it from the current ZWave network, and the LED will blink on the receptacle,when power on.
Ground
Green
Smart
Meter
5. Once program button is pressed and hold for 10 second, the device will send a
device reset locally notification to controller. Then clear all of information for the
network, and restore factory defaults, and reset the module. Use this procedure only
in the event that the network primary controller is missing or otherwise inoperable.
1. For retrofit applications, remove wall plate.
2. Warning!: Verify power is OFF before continuing.
3. Remove the existing receptacle from the box.
4. Disconnect the wiring from the existing receptacle.
5. Connect the Z-Wave receptacle as shown in the wiring diagram: Black lead to
hot wire, white lead to neutral wire, green lead to ground wire.
6. Check connections to be sure they are tight and no bare conductors are exposed.
7. Insert the ZW15RM receptacle into the outlet box carefully.
8. Make sure the ZW15RM receptacle to the box using the supplied screws
9. Attach the wall plate.
10. Restore power at the circuit breaker and test the system.
Remote Control
Z-Wave remotes provide control of an Individual device,Groups of devices and
Scenes. Please refer to your remote control’s instructions for details on its
capabilities and instructions for adding and controlling devices.
Please Note: After a power failure, the ZW15RM ’s Z-Wave controlled receptacle
returns to OFF state.
Advanced Operation
The following Advanced Operation parameters require that you have an advanced
controller. However, basic remotes do not have this capability.
-02-
-03-
INSTALLATION INSTRUCTIONS
All-ON and All-OFF
Brick, tile or concrete walls block more of the RF signal than walls made of
wooden studs and plasterboard (drywall).
Depending upon your primary controller, the ZW15RM receptacle can be set to
respond to ALL-ON and ALL-OFF commands in up to four differnet ways. Some
controllers may not be able to change the response from its default setting. Please
refer to your controller’s instructions for information on wether or not it supports the
the configuration function and if so, how to change this setting.
The four possible responses are:
- It will respond to ALL-ON and the ALL-OFF command (default).
- It will not respond to ALL-ON or ALL-OFF commands.
- It will respond to the ALL-OFF command but will not respond to the ALL-ON
command.
- It will respond to the ALL-ON command but will not respond to the ALL-OFF
command.
Wall mounted Z-Wave devices installed in metal junction boxes will suffer a
significant loss of range (approximately 20%) since the metal box blocks a
large part of the RF signal.
Effects of Home Construction on Wireless Range Between
Z-Wave Enabled Devices.
Configuration
Parameter
NO.
Size
1 Byte
Description
synchronization of outlet
power and LED indicator
Valid Value
0: Power on, LED off
1: Power on, LED on
Default
Value
Number of
Walls or
Obstacles
Default=0
Association
Grouping ID Max number of nodes
0**
Brick, Tile or
Concrete
Plastic
J-Boxes*
Plastic
Metal
J-Boxes* J-Boxes
131’
90’
66’
45’
105’
76’
52’
35’
131’
80’
48’
28’
100’
65’
40’
20’
Description
Lifeline: Send device reset locally notification
StatusReport: Send basic report
PowerReport: Send meter power report
All network settings and configuration parameters can all be restored to their
factory default settings by using your master controller or manual reset control to
reset the device.
Over-Current Protection
Over-current protection is provided by the routine which will turn off the relay when
WIRELESS RANGE
the power is more than the rate power.
This device complies with the Z-Wave standard of open-air, line of sight transmission
distances of 131 feet. Actual performance in a home depends on the numbers of
walls between the remote controller and the destination device, the type of construction
and the number of Z-Wave enabled devices installed in the control network.
Z-Wave Network
EveryNETWORAV Z-Wave enabled device acts as a signal repeater and multiple devices result
Z-WAVENTORK
in more possible transmission routes which helps
eliminate " RF dead-spots."
Things to consider regarding RF range:
Each wall or obstacle (i.e.:refrigerator, big screen TV, etc.)between the remote
or a Z-Wave device and the destination device will reduce the maxium range
of 131 feet by approximately 25-30%.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user authority to operate the equipment.
TROUBLESHOOTING
Cannot carry out add, remove or association
1. Confirm that the receptacle is powered.
2. Check if the wireless distance is too far.
The LED indicator does not turn ON
Restoring Factory Defaults
- Consult the dealer or an experienced radio/TV technician for help.
cause undesired operation .
Wood Frame with
Drywall
Metal
J-Boxes
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
(1) This device may not cause harmful interference, and (2) This device
must accept any interference received, including interference that may
From the Remote (or repeating Z-Wave module) to
destination device:
Type of
Construction
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
FCC COMPLIANCE STATEMENT
The equipment has been tested and found to comply with the limits for a class B
Digital Device, pursuant to part 15 of the FCC Rules. These limites are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment uses,generates and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction, may cause harmful
interference to radio communication. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment dose cause harmful
interference to radio or television reception, which reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the more of the following measures:
-04-05-
1. Check the wiring connection, especially the neutral wire.
2. Manually with the program button on the receptacle.
WARRANTY INFORMATION
Our company warranties its products to be free of defects in materials and workmanship for a period of two(2) years. There are no obligations or liabilities on the
part of our company for consequential damages arising out of or in connection
with the use or performance of this product or other indirect damages with respect
to loss of property, revenue, or profit, or cost of removal, installation or reinstallation.
Nov, 2017
20171113-00037

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Author                          : YB
Create Date                     : 2001:08:30 12:37:41+08:00
Modify Date                     : 2016:08:04 09:55:09+08:00
Subject                         : 
Has XFA                         : No
Page Count                      : 2
XMP Toolkit                     : XMP Core 5.1.2
Creator Tool                    : Adobe PageMaker 6.52
Metadata Date                   : 2011:07:30 09:18:21+08:00
Format                          : application/pdf
Description                     : 
Creator                         : YB
Title                           : 
Keywords                        : 
Producer                        : Acrobat Distiller 7.0 for Macintosh
Document ID                     : uuid:d05d9166-9d00-11d5-813a-000a9578dc4c
Instance ID                     : uuid:c33b40fa-95f4-4f7a-9b79-8cf79c974ea4

EXIF Metadata provided by EXIF.tools