WG security WGWFCB 58 KHz Electronic Article Surveillance System User Manual Manual

WG Security Products, Inc 58 KHz Electronic Article Surveillance System Manual

Manual

58KHz WiFi Floor Guard & Door Guard EAS Systems (EAS5.0 ver1.6 AM board) Installation Manual March 2015 Manual Ver. 03261501 TM
WG SECURITY PRODUCTS INC. 2105 S. Bascom Ave., Suite 316, Campbell, CA 95008 (USA) http://www.wgspi.com Technical Support Contact Information North America South America Tel: 408-241-8000 Fax: 408-559-2073 Email: service@wgspi.com Rest of World Tel: +49 8654 7715-0 Fax: +49 8654 7715-29 Email: support@wgglobal.eu WARRANTY DISCLAIMER WG Security Products Inc. makes no representation or warranty with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Further, WG Security Products Inc. reserves the right to revise this publication and make changes from time to time in the content hereof without obligation of WG Security Products Inc. to notify any person of such revision or changes. CRITICAL NOTES As specified by FCC Regulations 15.21, any changes or modifications not expressly approved by the party responsible for compliance of this equipment, will void the user’s permission and authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
TABLE OF CONTENTS OVERVIEW ..................................................................................................................... 1 System Overview ......................................................................................................... 1 System Configurations ................................................................................................. 2 Product Codes and Descriptions ................................................................................. 3 Specifications .............................................................................................................. 4 CONTROLLER CIRCUIT BOARD .................................................................................. 5 WiFi Main Board Connectors ....................................................................................... 5 System Configuration .................................................................................................. 6 PRE-INSTALLATION INFORMATION ............................................................................ 7 Quick Start for System Connections ............................................................................ 7 SMART POWER SUPPLY (WG SPS-24) ..................................................................... 12 Controls and Connections ......................................................................................... 12 Terminals Description ................................................................................................ 13 Main AC Input and Voltage Setup ............................................................................. 14 External Relay interface ............................................................................................. 15
(THIS PAGE INTENTIONALLY LEFT BLANK)
WiFi Floor Guard & Door Guard EAS Systems 1 OVERVIEW System Overview All WIFI EAS Systems utilize a common controller, differing only in the antennas that are used. Pedestal controllers (Ad Guard, Ad Guard XL, Premier Guard and Premier Pro) are imbedded in the pedestal base. Door Guard and Floor Guard controllers are contained in a separate housing. In either case, the controller is comprised of a main circuit board for performing all the functions of transmitting, receiving and alarm notification. The power board facilitates all the antenna transmission. This manual applies to the WiFi Floor Guard and WiFi Door Guard. Door Guard and Floor Guard Antennas These modules contain only the antennas whose operation and power are derived from the separate Control and Adaptor boxes. WiFi Control and Adaptor Boxes The Controller Box contains the WiFi Controller and PSU (WG SPS-24) for controlling the antenna and processing tag data. Between the Control Box and Antenna is the Adaptor Box which ensures signal stability between the WiFi Controller and the antennas. The Control Box includes WiFi capability so that the systems can be synchronized and tuned remotely over the Internet. WiFi Control Box WiFi Floor Guard WiFi Adapter Box WiFi Door Guard WiFi Controller WG SPS-24
WiFi Floor Guard & Door Guard EAS Systems 2 System Configurations Each WiFi system is powered by its own dedicated SPS. The SPS not only provides 24vac power to the transceiver pedestal, but it includes some very important features.  Accepts a wide range of AC input voltage  Controls transmitter bursts for troubleshooting  Adjusts pedestal alarm volume  Provides alarm visual & audio indication and relay output  Provides Jammer Detection alarm and relay output 24vac power and data/control is carried by a single TX cable from the SPS to the controller. The WiFi Control Box can only be connected to only one adaptor and from that to only one antenna. Caution! One WiFi Control Box can only be connected with one antenna and Adapter Box.
WiFi Floor Guard & Door Guard EAS Systems 3 Product Codes and Descriptions Systems Product Code Description Comment WG WFFG Floor Guard WiFi Transceiver, 6-foot Includes antennas, WiFi Control Box and Adaptor Box. WG WFDG Door Guard WiFi Transceiver, Gray Includes antenna, WiFi Control Box and Adaptor Box. WG WFDG-B Door Guard WiFi Transceiver, Black Includes antenna, WiFi Control Box and Adaptor Box. WG WFDG-W Door Guard WiFi Transceiver, White Includes antenna, WiFi Control Box and Adaptor Box. WG SPS-24 Smart Power Supply (24vac) Ordered separately but mounted inside the Control Box Accessories, Spares and Options Product Code Description Comment WG WFCB WiFi Control Box (with WG SPS-24) Included with WG WFFG and WG WFDG (N/A) Adaptor Box Included with WG WFFG and WG WFDG
WiFi Floor Guard & Door Guard EAS Systems 4 Specifications Smart Power Supply (WG SPS-24) Electrical Primary Input (Stepdown Transformer) 100vac 10 % 110vac 10 % 120vac 10 % 220vac 10 % 240vac 10 % Secondary Output 26Vac 5 % Rated Output Current 1.8A Maximum Secondary Output Current 1.9 A Built-in Fuse (self-resettable) 500mA Smart Power Supply (WG SPS-24) Mechanical Height 80mm ( 3.15” ) Width 110mm ( 4.33” ) Thickness 140mm ( 5.5” ) Weight 3 Kg ( 6.6 lbs) Environmental (Antenna, Control Box, Adaptor Box and Power Supply) Operating Temperature 45 C (113F) Relative Humidity 0 to 85% non-condensing Mechanical (Antenna, Control Box and Adaptor Box) Floor Guard Antenna 59.25”L x 15.75”W (150.5cm x 40cm) Thickness 1.13” (2.9cm) Weight 33 lb. (15kg) Door Guard Antenna 59”H x 9.5”W x 1.75”D (150 x 24 x 4.4cm) Weight TBD Control Box Dimensions TBD Weight TBD Adaptor Box 7.75” x 7.5” x 3.5” (197 x 190 x 90cm) Weight TBD
WiFi Floor Guard & Door Guard EAS Systems 5 CONTROLLER CIRCUIT BOARD WiFi Main Board Connectors WiFi Module Alarm Connector TX Connector RX Connector
WiFi Floor Guard & Door Guard EAS Systems 6 WiFi Adapter Box System Configuration Transmit and receive antennas are connected to the WiFi Control Box through the Adapter Box. The following diagram illustrates the connections. WiFi Floor antenna WiFi Control Box Connections Legend TX Loop Driving Cable RX Signal Receiver Antennas (Green) Transmitter Antenna (Blue) WiFi Door Guard --OR--
WiFi Floor Guard & Door Guard EAS Systems 7 PRE-INSTALLATION INFORMATION Quick Start for System Connections A Floor Guard system consists of a smart power supply (WG SPS-24), WiFi Control Unit, Floor Antenna and Adapter box. A Door Guard system consists of a smart power supply (WG SPS-24), WiFi Control Unit, Door Guard and Adaptor Box. Connection between the various modules is identical. The smart power supply has a 6-pin output connector for the 24vac output to power the WiFi Controller and also communicate with the control unit for tuning control and remote alarm display features. The WiFi Control Box is powered and controlled by the WG SPS-24 power supply unit. Also the control unit has two 4-conductor connectors for cables that will connect to the WIFI Control Unit AM board. One of the connectors is 4-pin connector for TX transmitting signals from the Control Unit to drive a loop antenna coil. The other connector is a 4-pins connector for RX signals from the Control Unit to receive signals from Floor Guard RX antennas. Note: Both the TX and RX cables are color coded and it is critical not to transpose the order.
WiFi Floor Guard & Door Guard EAS Systems 8 WIFI Control Unit and Adapter box and antenna Connection P1 P2 P3 P4 White White P1 P2 P3 P4 Red Green Red Green P1 P2 P3 P4 Red Brown P1 P2 P3 P4 White Green Blue Orange J2 J1 J2 J3 J5 J5-1 J4 J4-1 J7 J7-1 J6 J6-1 J3 J5 J1 J5-1
WiFi Floor Guard & Door Guard EAS Systems 9  J3 port of Adapter Box connects to the Transmit antenna (2 white wires).  J1 port of the Adaptor Box connects to the figure “O” antenna.  J2 port of the Adaptor Box connects to the figure “8” antenna. At this time there is no connection required for figure “8”; only figure “O”.  J5 port of the Adaptor Box connects the RX antenna to Adapter PCB (2pcs 2-core wires).  J5-1 port of the Adaptor Box is the output port for RX antenna.  SW5 is antenna phasing adjustment switch. Use this switch to adjust if the site is too noisy. P1 P2 P3 P4 P5 P6 P7 P8 White Green Blue Orange P1 P2 P3 P4 Brown Red SW5
WiFi Floor Guard & Door Guard EAS Systems 10 TX ampere debug Connect transmit detector to J1, turn on the power supply of CB and transmit detector, adjust TX “O” debug jumper, from the bottom the up. System will be under optimum working status when the transmit detector shows a value from 17 to 22. TX “O” debug jumper TX “8” debug jumper
WiFi Floor Guard & Door Guard EAS Systems 11 Antenna Installation Instructions: The antenna is designed to be buried in the flooring, in a rectangular of sufficient size to conveniently fit the antenna size. Coverage may be standard flooring (concrete or wood material). There is a cable extending out of the antenna case. Ensure the connector end is extended far enough for service access. Distance from the Antenna Box to the antenna should be no more than 25 feet. Distance between the Antenna Box and Controller should be no longer than the included interconnect cable.
WiFi Floor Guard & Door Guard EAS Systems 12 SMART POWER SUPPLY (WG SPS-24) Controls and Connections Fuse Replacement: Internal AC fuse rating (T3.15AL, 250V) SPS Power On/Off Switch Main AC Power In 24vac Power & Data Output Input Voltage Select Switch A Input Voltage Select Switch B SPS Front View SPS Top View SPS Rear View Pedestal Alarm Volume Adjust TX Antenna On/Off Switch Caution! Remove power before service.
WiFi Floor Guard & Door Guard EAS Systems 13 Terminals Description SPS Output Terminal Layout (10 pins) SPS to Pedestal Cable (6 wires) Alarm Relay Jammer Relay Pin # 1 2 3 4 5 6 7 8 9 10 Function GND 24VAC TX OFF Alarm Anti- Jammer Alarm Volume Electrical Common GND 26 VAC >4.0vdc <2.5vdc <2.5vdc 5-15vdc 1A Contact 1A Contact I/O Output Output Output Input Input Output Output Output SPS Main AC Input Terminal Layout Main AC Cable (3 wires) Pin Function Color 1 Neutral Blue 2 Ground Green w/Yellow Stripe 3 Live Red(Brown) 1 2 3 N - GND - L Main AC Input Terminal 1 2 3 4 5 6 7 8 9 10 LED Status LED On Off TX Off TX is Off TX is On System Alarm Alarm Enabled Alarm Disabled Jammer Detection Detection Enabled Detection Disabled Alarm Volume Dim Means Weaker Bright Means Louder Pin: Pin:
WiFi Floor Guard & Door Guard EAS Systems 14 Main AC Input and Voltage Setup The Smart Power Supply (WG SPS-24) accepts 5 input voltages: 100vac 110vac and 120vac in North America and Japan, 220vac and 240vac in Europe and Australia. Caution: Set the two Voltage Switches (A and B) on the power supply at the specified combination based on the local incoming voltage value (see picture below). Voltage Switch B HIGH MID LOW (Three Positions) AC Power In 100vac Voltage Switch A - 115 Voltage Switch B - LOW 110vac Voltage Switch A - 115 Voltage Switch B - MIDDLE 120vac Voltage Switch A - 115 Voltage Switch B - HIGH 220vac Voltage Switch A - 230 Voltage Switch B - MIDDLE 240vac Voltage Switch A - 230 Voltage Switch B - HIGH Voltage Switch A
WiFi Floor Guard & Door Guard EAS Systems 15 External Relay interface The external relay interface is located at Output side of the SPS. *** Suggested Relay Ratings 1A@ 24 VDC Notes: 1. Wire length to the dry contact circuit is limited to 20 feet. 2. To prevent high voltage noise from being introduced into the transceiver and degrading the system’s performance, it is highly recommended that you use a 24vdc output relay. Last 4 pins on this end. Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10 Power Supply Output Terminal Layout (10 pins) SPS to Pedestal Cable (6 wires) Alarm Relay Jammer Relay Pin # 1 2 3 4 5 6 7 8 9 10 Function GND 24VAC TX OFF Alarm Anti- Jammer Alarm Volume Electrical 1A Contact Rating 1A Contact Rating

Navigation menu