WG security WGWFCB 58 KHz Electronic Article Surveillance System User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	2577514
Application ID	8kHfYJQp0BV+4KIKZJ95Ew==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	79.59kB (994932 bits)
Date Submitted	2015-04-07 00:00:00
Date Available	2015-04-07 00:00:00
Creation Date	2015-03-26 06:10:44
Producing Software	Microsoft® Word 2010
Document Lastmod	2015-03-26 06:10:44
Document Title	Manual
Document Creator	Microsoft® Word 2010
Document Author:	WG Security Products Inc.

TM
58KHz
WiFi Floor Guard & Door Guard
EAS Systems
(EAS5.0 ver1.6 AM board)
Installation Manual
March 2015
Manual Ver. 03261501
WARRANTY DISCLAIMER
WG Security Products Inc. makes no representation or warranty with respect to the
contents hereof and specifically disclaims any implied warranties of merchantability or
fitness for any particular purpose. Further, WG Security Products Inc. reserves the right
to revise this publication and make changes from time to time in the content hereof
without obligation of WG Security Products Inc. to notify any person of such revision or
changes.
CRITICAL NOTES
As specified by FCC Regulations 15.21, any changes or modifications not expressly approved by
the party responsible for compliance of this equipment, will void the user’s permission and
authority to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used
in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
WG SECURITY PRODUCTS INC.
2105 S. Bascom Ave., Suite 316, Campbell, CA 95008 (USA)
http://www.wgspi.com
Technical Support Contact Information
North America
South America
Tel: 408-241-8000
Fax: 408-559-2073
Email: service@wgspi.com
Rest of World
Tel: +49 8654 7715-0
Fax: +49 8654 7715-29
Email: support@wgglobal.eu
TABLE OF CONTENTS
OVERVIEW ..................................................................................................................... 1
System Overview ......................................................................................................... 1
System Configurations................................................................................................. 2
Product Codes and Descriptions ................................................................................. 3
Specifications .............................................................................................................. 4
CONTROLLER CIRCUIT BOARD .................................................................................. 5
WiFi Main Board Connectors ....................................................................................... 5
System Configuration .................................................................................................. 6
PRE-INSTALLATION INFORMATION ............................................................................ 7
Quick Start for System Connections ............................................................................ 7
SMART POWER SUPPLY (WG SPS-24) ..................................................................... 12
Controls and Connections ......................................................................................... 12
Terminals Description ................................................................................................ 13
Main AC Input and Voltage Setup ............................................................................. 14
External Relay interface ............................................................................................. 15
(THIS PAGE INTENTIONALLY LEFT BLANK)
WiFi Floor Guard & Door Guard EAS Systems
OVERVIEW
System Overview
All WIFI EAS Systems utilize a common controller, differing only in the antennas that are
used. Pedestal controllers (Ad Guard, Ad Guard XL, Premier Guard and Premier Pro) are
imbedded in the pedestal base. Door Guard and Floor Guard controllers are contained in a
separate housing. In either case, the controller is comprised of a main circuit board for
performing all the functions of transmitting, receiving and alarm notification. The power board
facilitates all the antenna transmission. This manual applies to the WiFi Floor Guard and
WiFi Door Guard.
Door Guard and Floor Guard Antennas
These modules contain only the antennas whose operation and power are derived from the
separate Control and Adaptor boxes.
WiFi Control and Adaptor Boxes
The Controller Box contains the WiFi Controller and PSU (WG SPS-24) for controlling the
antenna and processing tag data. Between the Control Box and Antenna is the Adaptor Box
which ensures signal stability between the WiFi Controller and the antennas. The Control Box
includes WiFi capability so that the systems can be synchronized and tuned remotely over the
Internet.
WiFi Floor Guard
WiFi Door Guard
WiFi Controller
WG SPS-24
WiFi Control Box
WiFi Adapter Box
WiFi Floor Guard & Door Guard EAS Systems
System Configurations
Each WiFi system is powered by its own dedicated SPS. The SPS not only provides 24vac
power to the transceiver pedestal, but it includes some very important features.
 Accepts a wide range of AC input voltage
 Controls transmitter bursts for troubleshooting
 Adjusts pedestal alarm volume
 Provides alarm visual & audio indication and relay output
 Provides Jammer Detection alarm and relay output
24vac power and data/control is carried by a single TX cable from the SPS to the controller.
The WiFi Control Box can only be connected to only one adaptor and from that to only one
antenna.
Caution! One WiFi Control Box can only be connected
with one antenna and Adapter Box.
WiFi Floor Guard & Door Guard EAS Systems
Product Codes and Descriptions
Systems
Product Code
Description
Comment
WG WFFG
Floor Guard WiFi Transceiver, 6-foot
Includes antennas, WiFi Control
Box and Adaptor Box.
WG WFDG
Door Guard WiFi Transceiver, Gray
Includes antenna, WiFi Control
Box and Adaptor Box.
WG WFDG-B
Door Guard WiFi Transceiver, Black
Includes antenna, WiFi Control
Box and Adaptor Box.
WG WFDG-W
Door Guard WiFi Transceiver, White
Includes antenna, WiFi Control
Box and Adaptor Box.
WG SPS-24
Smart Power Supply (24vac)
Ordered separately but mounted
inside the Control Box
Accessories, Spares and Options
Product Code
Description
Comment
WG WFCB
WiFi Control Box (with WG SPS-24)
Included with WG WFFG and
WG WFDG
(N/A)
Adaptor Box
Included with WG WFFG and
WG WFDG
WiFi Floor Guard & Door Guard EAS Systems
Specifications
Smart Power Supply (WG SPS-24) Electrical
100vac 10 %
Primary Input
(Stepdown Transformer)
110vac 10 %
120vac 10 %
220vac 10 %
240vac 10 %
Secondary Output
26Vac 5 %
Rated Output Current
1.8A
Maximum Secondary
Output Current
1.9 A
Built-in Fuse (self-resettable)
500mA
Smart Power Supply (WG SPS-24) Mechanical
Height
80mm ( 3.15” )
Width
110mm ( 4.33” )
Thickness
140mm ( 5.5” )
Weight
3 Kg ( 6.6 lbs)
Environmental (Antenna, Control Box, Adaptor Box and Power Supply)
Operating Temperature
45 C (113F)
Relative Humidity
0 to 85% non-condensing
Mechanical (Antenna, Control Box and Adaptor Box)
Floor Guard Antenna
59.25”L x 15.75”W (150.5cm x 40cm)
Thickness 1.13” (2.9cm)
Weight 33 lb. (15kg)
Door Guard Antenna
59”H x 9.5”W x 1.75”D (150 x 24 x 4.4cm)
Weight TBD
Control Box
Dimensions TBD
Weight TBD
Adaptor Box
7.75” x 7.5” x 3.5” (197 x 190 x 90cm)
Weight TBD
WiFi Floor Guard & Door Guard EAS Systems
CONTROLLER CIRCUIT BOARD
WiFi Main Board Connectors
WiFi Module
TX
Connector
RX
Connector
Alarm Connector
WiFi Floor Guard & Door Guard EAS Systems
System Configuration
Transmit and receive antennas are connected to the WiFi Control Box through the Adapter
Box. The following diagram illustrates the connections.
WiFi Floor antenna
Connections Legend
TX Loop Driving Cable
RX Signal
Receiver Antennas
(Green)
Transmitter Antenna
(Blue)
WiFi Adapter Box
--OR--
WiFi Control Box
WiFi Door Guard
WiFi Floor Guard & Door Guard EAS Systems
PRE-INSTALLATION INFORMATION
Quick Start for System Connections
A Floor Guard system consists of a smart power supply (WG SPS-24), WiFi Control Unit,
Floor Antenna and Adapter box. A Door Guard system consists of a smart power supply (WG
SPS-24), WiFi Control Unit, Door Guard and Adaptor Box. Connection between the various
modules is identical.
The smart power supply has a 6-pin output connector for the 24vac output to power the WiFi
Controller and also communicate with the control unit for tuning control and remote alarm
display features.
The WiFi Control Box is powered and controlled by the WG SPS-24 power supply unit. Also
the control unit has two 4-conductor connectors for cables that will connect to the WIFI
Control Unit AM board. One of the connectors is 4-pin connector for TX transmitting signals
from the Control Unit to drive a loop antenna coil. The other connector is a 4-pins connector
for RX signals from the Control Unit to receive signals from Floor Guard RX antennas.
Note: Both the TX and RX cables are color coded and it is critical not to transpose the
order.
WiFi Floor Guard & Door Guard EAS Systems
WIFI Control Unit and Adapter box and antenna Connection
J1
J3
J2
J2
J6
J6-1
J5
J5-1
J7
J7-1
J4
J4-1
J3
J5
P1
P2
P3
White
P1
Red
P4
White
P2
Green
P3
Red
P4
Green
J1
J5-1
P1
Red
P2
Brown
P3
P1
White
P4
P2
Green
P3
Blue
P4
Orange
WiFi Floor Guard & Door Guard EAS Systems
SW5
 J3 port of Adapter Box connects to the Transmit antenna (2 white wires).
 J1 port of the Adaptor Box connects to the figure “O” antenna.
 J2 port of the Adaptor Box connects to the figure “8” antenna. At this time there is no
connection required for figure “8”; only figure “O”.
 J5 port of the Adaptor Box connects the RX antenna to Adapter PCB (2pcs 2-core wires).
 J5-1 port of the Adaptor Box is the output port for RX antenna.
 SW5 is antenna phasing adjustment switch. Use this switch to adjust if the site is too noisy.
P1
Brown
P2
Red
P3
P4
P1
P2
P3
P4
P5
White
P6
Green
P7
Blue
P8
Orange
WiFi Floor Guard & Door Guard EAS Systems
TX ampere debug
TX “8” debug jumper
TX “O” debug jumper
Connect transmit detector to J1, turn on the power supply of CB and transmit detector, adjust
TX “O” debug jumper, from the bottom the up. System will be under optimum working status
when the transmit detector shows a value from 17 to 22.
10
WiFi Floor Guard & Door Guard EAS Systems
Antenna Installation Instructions:
The antenna is designed to be buried in the flooring, in a rectangular of sufficient size to
conveniently fit the antenna size. Coverage may be standard flooring (concrete or wood
material).
There is a cable extending out of the antenna case. Ensure the connector end is extended far
enough for service access. Distance from the Antenna Box to the antenna should be no more
than 25 feet. Distance between the Antenna Box and Controller should be no longer than the
included interconnect cable.
11
WiFi Floor Guard & Door Guard EAS Systems
SMART POWER SUPPLY (WG SPS-24)
Controls and Connections
SPS Front View
SPS Power
On/Off Switch
Fuse Replacement:
Internal AC fuse rating
(T3.15AL, 250V)
Caution! Remove power
before service.
SPS Top View
Input Voltage
Select Switch A
Main AC Power In
TX Antenna
On/Off Switch
Pedestal Alarm
Volume Adjust
24vac
Power & Data
Output
SPS Rear View
Input Voltage
Select Switch B
12
WiFi Floor Guard & Door Guard EAS Systems
Terminals Description
SPS Main AC Input Terminal Layout
Main AC Cable (3 wires)
Pin Function Color
Neutral
Blue
Ground
Green w/Yellow Stripe
Live
Red(Brown)
N - GND - L
Pin:
Main AC
Input
Terminal
LED Status
Pin:
LED
On
Off
TX Off
TX is Off
TX is On
System
Alarm
Alarm
Enabled
Alarm
Disabled
Jammer
Detection
Detection
Enabled
Detection
Disabled
Alarm
Volume
Dim Means
Weaker
Bright Means
Louder
10
SPS Output Terminal Layout (10 pins)
SPS to Pedestal Cable (6 wires)
Alarm
Relay
Jammer
Relay
Pin #
Function
GND
24VAC
TX OFF
Alarm
AntiJammer
Alarm
Volume
Electrical
Common
GND
26
VAC
>4.0vdc
<2.5vdc
<2.5vdc
5-15vdc
1A
Contact
1A
Contact
I/O
Output
Output
Output
Input
Input
Output
Output
Output
13
10
WiFi Floor Guard & Door Guard EAS Systems
Main AC Input and Voltage Setup
The Smart Power Supply (WG SPS-24) accepts 5 input voltages: 100vac 110vac and 120vac
in North America and Japan, 220vac and 240vac in Europe and Australia.
Caution: Set the two Voltage Switches (A and B) on the power supply at the specified
combination based on the local incoming voltage value (see picture below).
AC Power In
Voltage Switch A
Voltage Switch B
HIGH MID LOW
(Three Positions)
100vac
Voltage Switch A - 115
220vac
Voltage Switch A - 230
Voltage Switch B - LOW
Voltage Switch B - MIDDLE
110vac
Voltage Switch A - 115
240vac
Voltage Switch A - 230
Voltage Switch B - MIDDLE
Voltage Switch B - HIGH
120vac
Voltage Switch A - 115
Voltage Switch B - HIGH
14
WiFi Floor Guard & Door Guard EAS Systems
External Relay interface
The external relay interface is located at Output side of the SPS.
Suggested Relay Ratings
1A@ 24 VDC
Last 4 pins on this end.
Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 Pin 6 Pin 7 Pin 8 Pin 9 Pin 10
Power Supply Output Terminal Layout (10 pins)
Alarm
Relay
SPS to Pedestal Cable (6 wires)
Pin #
Function
GND
24VAC
TX OFF
Alarm
AntiJammer
Alarm
Volume
Jammer
Relay
1A
Contact Rating
Electrical
Notes:
1. Wire length to the dry contact circuit is limited to 20 feet.
2. To prevent high voltage noise from being introduced into
the transceiver and degrading the system’s performance,
it is highly recommended that you use a 24vdc output
relay.
***
15
10
1A
Contact Rating

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 19
Language                        : en-US
Tagged PDF                      : Yes
Author                          : WG Security Products Inc.
Creator                         : Microsoft® Word 2010
Create Date                     : 2015:03:26 06:10:44-07:00
Modify Date                     : 2015:03:26 06:10:44-07:00
Producer                        : Microsoft® Word 2010

EXIF Metadata provided by EXIF.tools