WHIRLPOOL Personal Valet Manual L0204148
User Manual: WHIRLPOOL WHIRLPOOL Personal Valet Manual WHIRLPOOL Personal Valet Owner's Manual, WHIRLPOOL Personal Valet installation guides
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
Paff No, 8527279 Tip Over Hazard Do not use clothes vitalizer until completely installed. Install lag bolts securely into wall studs. Use two or more people to move and install clothes vitalizer. Failure to follow these instructions can result in death or serious injury. www.personalvalet.com IMPORTANT: Read and save these instructions. IMPORTANT: Installer: Leave Installation Instructions with the owner. Owner: Keep Installation instructions for future reference. Save: Installation Instructions for local electrical inspector's use. TM Trademark of Whirlpool, U.S.A. Before you start... Electrical requirements Your safety and the safety of others are very important. Ne have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. symbol. This is the safety alert Electrical Shock Hazard This symbol alerts you to potential hazards that can kill or hurt you and others. Plug into a grounded 3-prong outlet. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING". These words mean: Do not use an adapter. Do not use an extension cord. You can be killed or seriously injured if you don't immediately follow instructions. You can be killed or seriously injured If you don't follow instructions. All safety messages will tell you what the potential hazard is, tell you how 1o reduce the chance of injury, and tell you what can happen if the instructions are not followed. It is your .. responsibdRyto: Observe all governing codes and ordinances. Check code requirements: Some codes limit or do not permit installation of this product in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector. Comply with the installation specifications and dimensions. Consider spacing requirements for companion appliances. Make sure you have everything necessary for proper installation. Properly install appliance. Contact a qualified installer to insure that the electrical installation meets all national and local codes and ordinances. Do not remove ground prong. Failure to follow these instructions can result in death, fire, or electrical shock. 4 Important: Observe all governing codes and ordinances. A 120-volt, 60-Hz, AC-only, 15- or 20-ampere fused electrical supply is required. A Time-delay fuse or circuit breaker is recommended, It is recommended that a separate circuit serving only this appliance be provided. If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. 3-prong ground-type outlet must be located within 5 feet of lower right corner of appliance. Recommended ground method The clothes vitalizer, when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes, with National Electrical Code, ANSI/ NFPA 70". GROUNDING INSTRUCTIONS: This clothes vitalizer must be grounded. In the event of malfunction or breakdown, grounding will reduce the dsk of electdc shock by providing a path of least resistance for electric current. The power supply cord plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. WARNING - Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician. 3-prong ground goutlet ^ A plug __ r / / power suppty cord ground prong Tools needed for installation: • stud finder (optional) • drill (electric recommended) • 5/32" drill bit (pilot hole for lag bolt) • tape measure • pencil • carpenter's level • 7/16" wrench (ratchet recommended) for lag bolts if installing on a concrete or concrete block wall • concrete ddll bit for wall anchors (refer to wall anchor for drill bit size) • hammer Parts supplied for installabon: (inside accessory box) • 2, 1/4" x 2" lag bolts (for wood studs) • 2, 1/4-20" nuts • 1 mounting bracket cover (can be painted or covered with wallpaper) • separate metal mounting bracket assembly • 6, 1/8=thick adhesive backed cabinet spacers Copies of the standards listed above may be obtained from: • National Fire Protection AasodalJon One Batterymardn Park Quincy, Massachusetts 02269 PAGE 2 Parts not supplied for installation: Product Dimensions i1. 24 .... 2, 1/4"x1-1/4" lag bolts with wall anchors for concrete or concrete block wall installations. Note: Lag bolt length is based on mounting bracket thickness only. Add thickness of any wall coverings to length of tag bolts/wall anchors used. These can be obtained from local hardware store. Now start... 130-;/4. both doors 3' 90 ° * 12" minimum clearance to side wall on left side of appliance is required for air venting. ** 24" minimum clearance to ceiling or any non-removable object (cabinet, soffit, shelf, etc.) above vitalizer is required for serviceability. 5g" I A Model shown: PVWN600 Tip Over Hazard Do not use clothes vitalizer until completely installed. Install lag bolts securely into wall studs. Use two or more people to move and install clothes vitalizer. 6 ft. power supply cord. 3-prong ground-type out]at must be located within 5 feet of lower right comer. 1" minimum clearance required at bottom of vitalizer for ventilation. 35" overall depth (incl. handle) Failure to follow these instructions can result in death or serious injury. la With clothes vitalizer in carton, lay carton on back. g0_ Open doors and maximum remove contents. Important: Before the clothes vitalizer is installed on wall, do not open doors more than 90 ° to avoid damaging the door hinges. Shut doors and reapply tape or strap• Leave clothes vitalizer in box. models white doors biscuit doors weight 117 Ibs. 117 Ibs. A 15-1/4" 15-1/4" wood panel doors mirrored doors 129 Ibs. 143 Ibs. 15-1/8" 15-1/8" be level) studs 4a • Locate and mark the Wood installation centersstud of each wall stud. Make these marks about 72" from the floor, L_tine , II I I I 114-20 nuts I' I I I with level line a Remove the mounting bracket assembly, nuts and lag bolts (if installing in wall studs) from the accessory box. With washer sides of nuts facing mounting bracket, start nuts onto the bracket's threaded studs. ==Mark a horizontal line at least 24 inches long, 70-3/4" minimum from the floor. Important: The line MUST be level. 4b. |._'+_ +r"_Ini++++ i iI For wood stud installations, each lag bolt MUST be installed in a wood stud as shown. If there are not 2 studs in moun_ng area, DO NOT install vitalizer. DO NOT use toggle bolts through dry wall to support the clothes vitalizer. Align the lower edge of the mounting bracket assembly with the level line. Select and mark a hole location on each side of the bracket that is closest to the center of each stud. C• Set bracket aside and drill 5/32" pilot holes. PAGE 3 Concreteor concreteblock installation If clothes vitalizer does not operate: d • Align the lower edge of the mounting bracket assembly with the level line. Select and mark a hole location on each side of the bracket. • Check that circuit breaker is not tripped or house fuse blown. Model shown: e. • See Owner's Manual for troubleshooting list. Set bracket aside and drill holes. Drive the wall anchors into the holes with hammer. e Fasten the mounting bracket to wall. Check that the bracket is level then securely tighten the lag bolts. bracket nut ' mounting bracket wood stud shown • Space the mounting bracket nuts 1/2" to 3/8" away from mounting bracket. mounting stud m Lift clothes vitalizer up and slide keyhole slots over nuts. Lower vitalizer down onto mounting bracket studs and tighten nuts. • Check that power supply cord is plugged into wall outlet. If you need assistance: needed = Check tops of doors for uniform vertical alignment. Wall irregularities may require shimming the back bottom corners of the cabinet away from wall to align the door tops. If door tops are not aligned: • Carefully pull a bottom cabinet corner away from the wall and observe the alignment shift. • Separate adhesive backed spacers (in accessory box) but do not remove from the adhesive backing. • Insert spacers at either or both bottom comers to obtain door alignment. The spacers may be stacked for additional thickness if needed. • When alignment is obtained, remove the spacers from the adhesive backing and attach to back of cabinet. a Remove mounting bracket cover from accessory box. 0== Peel off adhesive protective strips. Align cover with bracket and press cover down against top of appliance. Note: Mounting bracket cover can be painted or covered with wallpaper. 1 • Plug power supply cord into grounded outlet. 2. If your clothes vitalizer came with a storage drawer, follow the instructions packed with the drawer and install it now. • Refer to Owner's Manual. • Call the Consumer Interaction Center. Check your Owner's Manual for a toll-free number to call or call the dealer from whom you purchased the clothes vitalizer. The dealer is listed in the Yellow Pages of your phone directory under "Appliances -Household - Major -Service and Repair." If you need service: Maintain the quality built into your clothes vitalizer by calling an authorized service company. To obtain the name and number of an authorized service company: • Contact the dealer from whom you purchased your clothes vitalizer, or • Look in the Yellow Pages of your phone directory under "Appliances -Household - Major -- Service and Repair," or • Call the Consumer Interaction Center. The toll-free number is listed in your Owner's Manual. When you call, you will need: • The clothes vitalizer model number. • The clothes vitalizer serial number. Both numbers are listed on the model/serial number plate located on the lower cabinet frame next to the door magnet. Accessories: The following storage drawer kits are available from your dealer: Kit No. 8527309 White Kit No. 8527310 Biscuit Kit No, 8527308 Signet Grey Part No.8527279 O2001 Whirlpool Corporation Benton Harbor, Michigan 49022 Printed in U.S.A.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 4 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Fri Apr 20 12:03:40 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools