WHIRLPOOL Built In Oven, Electric With Microwave Manual L0409230

GMC275PDB6 GMC275PDB6 WHIRLPOOL BUILT-IN OVEN, ELECTRIC WITH MICROWAVE - Manuals and Guides L0409230 View the owners manual for your WHIRLPOOL BUILT-IN OVEN, ELECTRIC WITH MICROWAVE #GMC275PDB6. Home:Kitchen Appliance Parts:Whirlpool Parts:Whirlpool BUILT-IN OVEN, ELECTRIC WITH MICROWAVE Manual

User Manual: WHIRLPOOL WHIRLPOOL Built In Oven, Electric with Microwave Manual WHIRLPOOL Built In Oven, Electric with Microwave Owner's Manual, WHIRLPOOL Built In Oven, Electric with Microwave installation guides

Open the PDF directly: View PDF PDF.
Page Count: 5

Quick Reference
Table of Contents:
Pages
[_ Product dimensions
[_ Cutout dimensions
[_ Before you start
[_ EUectricaUrequirements
[_ _ Installation steps
If you need assistance:
Check your Use and Care Guide for a toll-free number to call or call
the dealer from whom you purchased this appUiance.The dealer is
listed in the Yellow Pages of your phone directory under
"AppUiances-- Household -- Major -- Service and Repair."
Call when you:
Have questions about built-in oven installation or operation.
[_ Need to obtain the name and number of an authorized service
company.
When you call, you will need:
The built-in oven model number.
[_ The built-in oven serial number.
Both numbers are listed on the modellserial rating pJate, Jocated on
the microwave oven frame.
27" oven
25-3/8
recessed
width __
23"" raax.
recessed
depth
41"
recessed
height
42=7/I6"
overall
height
41=1/4"
cutout
height
4
1=I/2"
rain.
botteraef
cutoutto
top of
cabinet
door
27" rain,
cabinet width
25-1/2"
cutout ---_-
width
27" oven
?'top ofcutout
to bottoraof
uppercabinet
door
19=1/4"
bottom of
cutout to
floor
cabinet _
23=li4"rain.
cutout depth
23"recessed
oven depth
J
recessed
oven
oven
_-'-_ front
Cabinet side view
Page 1
30" OVeR
28-3/8"
recessed
width ___._,
2a"raa×.
recessed
depth
41"
recessed
height
29=3/4"
width
42=7/16"
overall
height
41=I/4"
cutout
height
=3=
1=1!2" rain,
bottom of
cutout to
top of
cabinet
door
30" pain,
cabinet
E
28=1/2"
-_--- cutout ---_
width
I" top
of cutout
to bottom
of upper
cabinet door
f
19=1/4"
bottom
ofcutout
to floor
30" Over
Cabinet filler kits are available from your dealer.
Use a matching color kit if oven is smaller than your
27" oven filler height is 7o13/16"
Black -- 4378950
White -- 4378951
Almond- 4378952
30" oven filler height is 4o13/16"
Black -- 4378944
White -- 4378945
Almond- 4378946
Tool needed:
Phillips screwdriver
Parts supplied:
__ 4 screws
Your safety and the safety of others are
very important.
We have provided many important safety
messagesin this manual and on your appiiance=
Always readand obey ali safety messages=
This is the safetyalert symbol=
Thissymbol alertsyou to potentiai hazards
that can kiii or hurt you and others=
Ati safety messageswiii foliow the safety alert
symbol and either the word "DANGER"or
"WARNING"=Thesewords mean:
You canhe killed or seriousmyinjuredif you
don't fellow instructions.
All safety messageswill tell you what the potential
hazard is, tell you howto reduce the chanceof
injury, and teii you what can happenif the
instructions are not foliowed=
important: Observe all governing codes
and ordinances.
Proper installation is your responsibility.
Have a qualified technician install this oven.
Oven location should be away from strong draft
areas, such as windows, doors and strong
heating vents.
Cabinet opening dimensions that are shown
must be used. Given dimensions provide
minimum clearance.
Recessed installation area must provide
complete enclosure around the recessed portion
of the oven.
Electrical ground is required. See "Electrical
requirements."
Etectrica_supply junction box shouN be located
3 inches maximum below the support surface
when oven is installed in a wall cabinet. Cutout
for wiring should be in the right rear or left rear
corner. For undercounter installation, it is
recommended that the junction box be located
in the adjacent right or left cabinet. If installing
junction box on rear wall behind oven, junction
box must be recessed and located in the upper
or lower right or left corner of cabinet.
Oven support surface MUST be solid, level and
flush with bottom of cabinet cutout.
Excessive Microwave Energy Exposure
Do Not attempt to operate the microwave
oven with the door open.
Do Not tamper with or defeat the safety
interlocks.
Do Not place objects between the microwave
oven front face and door.
Do Not allow soil or cleaner residue to
accumulate on searing surface of the
microwave oven door.
Do Not operate the microwave oven if
damaged.
Do Not operate the microwave oven if:
m door is bent.
hinges and latches are broken or loose.
door seals, sealing surfaces or glass are
broken.
The microwave oven door must close
properly to provide safe operation.
Have a qualified repair person adjust, repair
and check microwave oven for microwave
leakage after a repair is made.
Do Not use microwave for commercial
purposes. The microwave oven in this unit is
designed for household use only.
Failure to follow these instructions toured
result in exposure to excessive microwave
energy.
It is the customer's responsibility:
To contact a qualified electrical installer.
To assure that the electrical installation is
adequate and inconformance with National
Electrical Code, AN81/NFPA 70 E latest edition*,
and all local codes and ordinances.
Copies of the standards listed may be obtained ftora:
* National Fire Protection Association
Batteryraarah Park
Quincy, Massachusetts 02269
If codes permit and a separate grounding wire is
used, it is recommended that a qualified electrician
determine that the grounding path and wire gauge
are in accordance with toca_ codes.
Do Not ground to a gas pipe.
Check with aqualified electrician if you are not
sure oven is properly grounded.
Do Not have afuse in the neutral or grounding
circuit.
This oven must be connected to agrounding metal,
permanent wiring system.
Oven must be connected to the proper electrical
voffage and frequency as specified on the
modeU/sedd rating plate. (The model/serial rating
plate is located on the oven door or on the oven
frame.)
[_ Models rated from 7.3 to 9.6 kW at 240 volts
(5.5 to 7.2 kW at 208 volts) require a separate
40°ampere circuit. Models rated at 7.2 kW and
below at 240 volts (5.4 kW and below at 208
volts) require a separate 30°ampere circuit.
[_ A time-delay fuse or circuit breaker is
recommended.
[_ Connect directly to the fused disconnect (or
circuit breaker box) through flexible, armored
or non-metallic sheathed, copper cable (with
grounding wire).
[_ Flexible armored cable from appliance should
be connected directly to junction box.
[_ Fuse both sides of the line.
[_ A U.L.-iisted conduit connector must be
provided at the junction box.
[_ Do Not cut the conduit.
Wire sizes and connections must conform with the
rating of the appliance and to the requirements of
the National Electrical Code, ANSI/NFPA 70 -- latest
edition (% See Page 1) and all local codes and
ordinances.
if the house has aluminum wiring, follow the
procedure below.
a.) Connect the aluminum wiring to the copper
wire using special connectors designed and
Underwriters Laboratories-listed for joining
copper to aluminum. Follow the electrical
connector manufacturer's recommended
procedure.
b.) Aluminum/copper connection must conform
with local codes and industry-accepted wiring
practice.
Preparation
Excessive Weight Hazard
Use two or more people to move and
install oven.
Faiture to fol!ow this instruction can
result in back or other injury.
Important: Use both hands to remove oven
doors.
Do Not use handle or any portion of the front
frame or trim for lifting.
Before moving oven across floor, checkthat oven
is on shipping base or slide oven onto cardboard
or hardboard.
Do Not remove shipping feet at the front tower
corners of oven.
Do Not
remove
shipping feet.
_ Remove
side trim
pieces.
_power
supply cable
_ shipping
foot
Grasp oven frame
to lift oven.
Check oven and
microwave oven operation.
Use screws to attach
oven to cabinet.
Reattash side
trim pieces,
Remove
trim screws.
Remove
oven door.
[] Turn power supply off. Move oven
close to final position.
, Remove and discard shipping materials,
tape and protective film from the oven. Do
Not remove shipping base or shipping feet
at the front lower corners of oven. The
shipping feet will protect the lower oven
trim untiJ oven is inserted into cabinet.
• Remove and set aside racks and other parts
from inside oven.
latch on the hinge
in locked position =
door free to open
and close
latch on the hinge
unlocked
position = door
ready for removal
Pull top of trim
down,
[] Completely open oven door. In both back
corners of the door you will see door latches in the
locked position. Rotate both latches forward to the
unlocked position.
Grasp outside edges of door with both hands.
, Begin closing door, atthe moment the door
stops dosing, lift and pull door toward you.
, Set door aside on a protective surface.
[] Remove trim screws attaching right and
left side trim to oven. Grasp the bottom end of
trim and pull away from oven. Slide top end of
trim downward to remove trim from oven. Take
care not to scratch other surfaces with ends of
trim. Set trim and screws aside on protected
surface.
Page 2
Electrical connection
If your house has aluminum wiring, see
"Ebctrical requirements", Page 2.
Electrbal 8hock Hazard
Turn power supply off before connecting wires.
Use 8 gauge solid copper wire.
Ebctrically ground range.
Failure to follow these instructions can result
in death, fire, or electrical shock.
This oven is manufactured with white (neutral)
power supply wire and a cabinet=connected bare
grounding wire twisted together.
Feed oven cabb through opening in
the cabinet. Make ebctrical connection
following the steps needed for your installation.
1. Disconnect the power supply.
2. Remove the junction box cover.
3. Connect oven cable to junction box through the
U.L.-listed conduit connector.
4. Connect the two black wires together with
twist-on connectors.
5. Connect the two red wires together with
twist-on connectors.
6. Complete electrical connection according to
local codes and ordinances.
cable from
junction power supped/
box _
white _ -_
w,re _ _>_/¢"
grounding oven
cable wires --
factory crimped
Figure 1 cable from
oven
conduit
connector
if local codes PERMIT
connecting cabinet-grounding
conductor to neutral white
wire in junction box:
7. Connect the factory-crimped bare
and white oven cable wires to
the neutral (white) wire in
junction box. See Figure 1.
8. Replace junction box cover.
cabb from
junction power supply
Figure 2 cabte from connector
oven
ff bcal codes DO NOT PERMIT
connecting cabinet-grounding
conductor to neutral white
wire in junction box:
7. Separate the factory-crimped
bare and white oven cable wires.
& Connect white oven cable wire to
neutral (white) wire in junction
box. See Figure 2.
9. Connect the bare grounding
oven cable wire to a grounded
wire in the junction box. See
Figure 2.
lg. Replace junction box cover.
ff connecting to a
four-wire electrical system:
7. Separate bare and white
oven cable wires.
8. Connect white oven cable wire to
neutral (white) wire in junction
box, See Figure 2,
9. Connect the bare grounding oven
cable wire to the green grounding
wire in junction box. Do Not
connect bare grounding wire to
neutral (white} wire in junction
box. See Figure 2.
10. Replace junction box cover.
Attachment
Carefully push against seal area of oven front
frame when pushing oven into cabinet.
Do Not push against outside edges.
5_ Lift oven into cabinet cutout using the
oven opening as an area to grip.
shipping
foot
Push against seal area of front frame to push
oven into cabinet until shipping feet almost
contact cabinet. Use a Phillips screwdriver to
remove screws attaching shipping feet. Remove
and discard shipping feet.
Push oven completely into cabinet and center
oven in cabinet cutout.
t 4 SCrews
6_ important: Securely fasten oven to cabinet
using the screws provided (two screws for a single
oven or four screws for a double oven). Insert the
screws through hobs in mounting rails. Do Not
overtighten screws.
j_ Slide top
oftrim up.
7m Slide top end of each trim upward onto oven
side rails. Push each trim into place at bottom of
trim. Use screws to attach each trim to oven. Take
care not to scratch other surfaces with ends of trim,
8u Replace oven racks.
9m Reinstall the oven door by inserting
ends of hinges into hinge slots in the oven
frame. Push hinges in as far as they will go.
Open the door (you will feel the door drop
into place) and rotate both hinge latches back
to the locked position.
Close and open the door to check that the
door closes and opens completely. If door
does not close or open completely, repeat
the door removal step and reinstall door as
described above.
Check operation
Turn on power supply. The display
panel wiii light up briefly. "PF" should appear in
the temperature display.
Make sure the oven door is closed and the "ON"
light is shown in the display area. After 2 minutes,
partially open oven door. You should feel heat from
the oven. Press the "CANCEL" pad.
mfyour oven does not heat or an"F" appears in
the display, contact your dealer or cheek the "if
you need service..." section ef this installation
instructions,
Check the operation of your bwer
oven. Press the "BROIL" pad. "BROIL" wiii
appear in the display. Press the "START" pad.
2_ Check the operation of the
microwave oven,
, Fill a microwave-safe container with one cup of
water and place container inside microwave oven.
Close door firmly.
, Set microwave oven cool<time to "2:00"
minutes.
, Pressthe "START/ENTER" pad. The interior
microwave oven light should be on and the
remaining cooking time should be displayed.
Page 3
, When display reads "1:00," open microwave
oven door. The microwave should stop cooking.
, Close door firmly. The interior microwave oven
light should turn off.
, Pressthe "START/ENTER" pad. Microwave oven
should begin cooking and the microwave oven
interior light should be on.
, Let microwave oven complete cooking time. A
tone will sound four times at end of cooking time
and microwave oven will shut off.
, Open microwave oven door and carefully remove
container. Water in container should be hot.
To get the most efficient use
from your new oven, read your
Use and Care Guide. Keep installation
instructions
and Guide cbse to oven
for easy reference.
if oven does not operate:
[_ Check that circuit breaker is not tripped or
house fuse Mown.
[_ See Use and Care Guide for trouMeshooting Uist.
if you need assistance:
ff you have questions about operating, c_eaning or
maintaining your oven:
[_ Refer to Use and Care Guide.
[_ Call the Consumer Assistance Center: Check
your Use and Care Guide for a toll-free
number to call or call the dealer from whom you
purchased this appUiance.The dealer is Uistedin
the Yellow Pages of your phone directory under
"AppUiances -- HousehoH -- Major -- Service
and Repair."
if you need service:
Maintain the quality built into your built-in oven by
calling an authorized service company.
To obtain the name and number of an authorized
service company:
[_ Contact the dealer from whom you purchased
your built-in oven; or
[_ Look in the Yellow Pages of your telephone
directory under "Appliances -- Household --
Major -- Service and Repair" for an authorized
service company; or
[_ Call the Consumer Assistance Center. The toll-
free number is listed in your Use and Care Guide.
When you call, you will need:
[_ The built-in oven model number.
[_ The built-in oven serial number.
Both numbers are listed on the model/serial rating
plate, located on the microwave oven frame.
Part No. 8300653
© 2001 Printed in U.S.A.

Navigation menu