WINIA Electronics 7NFCMC526X 15-inch Color Monitor User Manual 526X EN
Dongbu Daewoo Electronics Corporation 15-inch Color Monitor 526X EN
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 88204 |
| Application ID | f2A0INapumGDD+LElWqllw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 28.3kB (353756 bits) |
| Date Submitted | 2000-02-25 00:00:00 |
| Date Available | 2000-03-08 00:00:00 |
| Creation Date | 1999-12-06 11:34:23 |
| Producing Software | Acrobat Distiller 3.01 for Power Macintosh |
| Document Lastmod | 2000-01-04 09:34:21 |
| Document Title | 526X EN |
| Document Creator | QuarkXPress3.3K: LaserWriter 8 8.3fc2 |
| Document Author: | 7300 |
USER’S GUIDE COLOR MONITOR Model No : 526X IMPORTANT SAFEGUARDS 1. Read all of these instructions. 2. Save these instructions for later use. 3. Unplug this monitor from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use attachments not recommended by the monitor manufacturer as they may cause hazards. 5. Do not use this monitor near water, e.g., near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, etc. 6. Do not place this monitor on an unstable cart, stand, or table. The monitor may fall, causing serious injury to a child or adult, and serious damage to the appliance. 7. Slots and openings in the cabinet and the back or bottom are provided for ventilation, to ensure reliable operation of the monitor, and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the monitor on a bed, sofa, rug, or other similar surface. This monitor should never be placed near or over a radiator or heat register. This monitor should not be placed in a built-in installation such as a bookcase unless proper ventilation is provided. 8. This monitor should be operated only from the type of power source indicated on the marking label. If you are not sure of the power supplied to your home, consult your monitor dealer or local power company. 9. This monitor is equipped with a 3-wire grounding-type plug, That is, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounding-type plug. 10. Do not allow anything to rest on the power cord. Do not locate this monitor where the cord will be abused by people walking on it. 11. Follow all warnings and instructions marked on the monitor. 12. For added protection for this monitor during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage to the monitor and/or the computer due to lightning and power line surges. 13. Do not overload wall outlets and extension cords as this can result in fire or electric shock. 14. Never push objects of any kind into this monitor through cabinet slots, as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the monitor. 15. Do not attempt to service this monitor yourself, as opening or removing covers may expose you to dangerous voltages or other hazards. Refer all servicing to qualified service personnel. 16. Unplug this monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions: FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cuase harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures : - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio or TV technician for help. a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the monitor. c. If the monitor has been exposed to rain or water. d. If the monitor does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore normal operation. e. If the monitor has been dropped or the cabinet has been damaged. f. When the monitor exhibits a distinct change in performance, this indicates a need for service. 17. When replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 18. Upon completion of any service or repairs to this monitor, ask the service technician to perform routine safety checks to determine that the monitor is safe to operate. CAUTION : Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. CANADIAN NOTICE This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. AVIS CANADIEN Cet appareil numérique de la Class B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. WICHTIGE INFORMATIONEN Bitte lesen Sie alle diese Informationen, bevor Sie das Gerät in Betrieb nehmen! Lesen Sie sich außerdem die Bedienungsanleitung komplett und sorgfältig durch, da nur in diesem Fall eine problemlose Inbetriebnahme erwartet werden kann. • Achten Sie darauf, daß das Gerät nur in eine 230V SchukoSteckdose eingesteckt wird. • Die Steckdose sollte jederzeit frei zugänglich sein um bei einem evtl. auftretenden Notfall das Gerät schnell vom Netz zu trennen. • Achten Sie desweiteren darauf, daß die Netzanschlußleitung nicht mechanisch beansprucht oder sonstwie beschädigt wird. • Offnen Sie das Gerät niemals! Im Inneren befinden sich Teile mit gefährlicher Spannung. • Bevor Sie das Gerät reinigen, ziehen Sie bitte den Netzstecker aus der Steckdose. Säubern Sie dann das Gerät mit einem feuchten (keinesfalls tropfnassen) Lappen. • Die in diesem Gerät entstehende Röntgenstrahlung ist ausreichend abgeschirmt (Ortsdosisleistung in 0.1m Abstand weniger als 1.0µ Sv/h). Beschleunigungsspannung maximal 25kV. • Stellen Sie das Gerät an einem ergonomisch günstigen Ort auf und sorgen Sie dafür, daß der Monitor mit nach GS-VW-SG7 geprüfter Peripherie betrieben wird, da nur unter diesen Umständen ein optimaler ergonomischer Betrieb des Gerätes sichergestellt ist. Falls Sie dennoch Fragen haben, auf die die Bedienungsanleitung keine hinreichende Antwort geben kann, so kontaktieren Sie bitte den nächsten Fachhändler. Maschinenlärminformationsverordnung 3. GSGV, 18.01 1991: Der arbeitsplatzbezogene Schalldruckpegel beträgt 70 dB (A) oder wenigergemäß ISO 7779. DECLARATION OF CONFORMITY We, Manufacturer / Importer DAEWOO ELECTRONICS CO., Ltd 541, 5-Ga, Namdaemoon-Ro, Jung-Gu Seoul, Korea declare under our sole responsibility that the product, Color Display monitor 526X to which this declaration relates is in conformity with the following standard(s) or other normative document(s) Safety : EN60950/1992/A1:1993/A2:1993 A3:1995/A4:1997 EMC : EN 55022/8.1994, EN 50082-1/1992 EN 60555 Part 2, 3/1987 following the provisions of 89/336 EEC-EMC Directive and the provisions of 73/23 EEC-Low Voltage Directive. Handed over by : S.Lee, Managing Director. Display Business Division Oct., 1999 Seoul Signature: S.Lee, Managing Director. Display Business Division. DAEWOO ELECTRONICS Co., Ltd Emission Characteristics Tested by SEMKO A sample of this type has been tested and has shown compliance with the guidelines in the swedish document MPR II (Optional). This product is also designed for IT power system with phase to phase voltage of 230V. The power cord is used as a main disconnect device. Disconnect the power cord before servicing. The outlet must be installed near the monitor and must be easily accessible. As an ENERGY STAR Partner, Daewoo Electronics Co., Ltd. has determined that this product meets the Energy Star guidelines for energy efficiency. The appliance is not intended for use by young children or infirm persons without supervision ; Young children should be supervised to ensure that they do not play with the appliance. CONTENTS Introduction ............................................................................. 1 Product Features ................................................................. 2 Setup ......................................................................................... 3 Installing the Tilt/Swivel Stand .......................................... 3 Connecting the Signal Cable and Power Cord..................... 4 Power Management System ............................................... 5 DDC for Plug & Play ......................................................... 5 Operation & Adjustment ...................................................... 6 Specifications ......................................................................... 12 Factory Preset Timings ......................................................... 12 Troubleshooting ..................................................................... 13 Appendix INTRODUCTION This manual explains how to correctly install, operate, and get the best performance from your monitor. Please read this user’s guide carefully before installing your monitor, then keep it near your monitor for quick reference. First, please check that the contents of the box corresponds with the following checklist : • • • • • Color monitor Power cord User’s Guide Tilt/swivel stand Warranty Card (Optional) If any item is missing or damaged, please contact your dealer. Please keep the box and packing materials so that you may properly store or transport your monitor. Description for D-sub Connector English-1 PRODUCT FEATURES • The convenient and user-friendly on-screen display allows for easy and accurate adjustments of horizontal and vertical screen size and position, geometry, and screen color. SETUP INSTALLING THE TILT/SWIVEL STAND 1. Ensure that the power is off to the monitor. • The monitor supports a safe working environment in strict compliance with the MPR II standard for low emissions (Optional). 2. Set the monitor face down with the underside facing you. Please be careful not to scratch the monitor screen. • The monitor complies with the VESA Display Data Channel (DDC) specification for Plug and Play compatibility. Advanced microcircuitry makes setup and configuration fast and effortless. 3. Align the four hooks on the stand with the guide holes on the bottom chassis of the monitor. • The monitor features Advanced Color Controls for fine-tuning to meet your own personal tastes or application requirements. Use the on-screen controls to adjust the color temperature, RGB gain value for the best possible screen color and intensity. 4. Insert the hooks into the guide holes. • Press the menu button and activate the Self-Diagnosis menu to determine whether your monitor is functioning normally, not receiving a signal or is receiving a signal that is out of scanning range. 6. Turn the monitor and the stand upright. • Activate the higher refresh rates of the monitor to stabilize the screen and eliminate the annoying flicker that contributes to eye-strain and headaches. • 5. Slide the tilt/swivel stand toward the front of the monitor until the latch locks in position. Latch The “borderless” full-screen display capability works under all graphic modes and provides a larger viewing area than conventional monitors, giving you a better picture with more workspace. If you want to remove the tilt/swivel stand on the monitor, press the latch and pull the tilt/swivel stand toward the back of the monitor. Lift the stand to separate. English - 2 English-3 CONNECTING THE SIGNAL CABLE AND POWER CORD 1. Turn off the computer and monitor. 2. Connect the 15 pin D-sub connector to the output port of the video card in your computer. 3. Tighten the screws of the connector. 4. Plug the power cord into the AC receptacle located on the back of the monitor. 5. Plug the other end of the power cord into the AC outlet. POWER MANAGEMENT SYSTEM If you use the monitor with a computer that complies with the power-saving program, you can set the monitor to go blank when the system has remained unused for a period of time. To specify the period or to disable this feature, set the system timeout field of the computer’s system setup program or use special software for power-saving. See the computer user’s manual for the details of using the system setup. While the monitor is in power-saving mode (blank screen), it consumes less power than when it is in its normal state. The color of the power LED will indicate the state. To restore the screen image, press any key of your keyboard or move your mouse. If the signal cable is connected loosely or disconnected, the power-saving feature will not operate. DISPLAY DATA CHANNEL FOR PLUG AND PLAY If you use the monitor with a computer that complies with DDC1/2B/CI of VESA, the host video card automatically configures itself without your intervention in a way that best fits the attached monitor. The Display Data Channel(DDC) allows the monitor to inform the host system about configuration information for optimum use of the monitor. Use of the video card utility is not required to match the resolutions and refresh rates of the monitor and video card. Signal Cable Power Cord If your power cord is PC-to-Monitor type, plug the other end of the power cord into the AC receptacle in the computer. English - 4 English-5 OPERATION & ADJUSTMENT Key Process Control Panel MENU SELECT MENU • Launch OSD(On-Screen Display) MENU window. SELECT • Select a sub Menu & function. • • • Move a sub Menu & function. • • • Move a sub Menu & function. Increase the value of any selected function. Adjust the contrast directly when there is no OSD. MENU Decrease the value of any selected function. Start Adjust the brightness directly when there is no OSD. • English - 6 When you choose the icon exit the OSD screen. English-7 on the OSD window, you can OSD Functions ICON CONTROL FUNCTIONS ICON CONTROL FUNCTIONS Adjust the side pin corner balance top Adjust the position of the display horizontally (left or right). T. PIN BALANCE when the top sides of the screen are V. POSITION Adjust the position of the display vertically (up or down). B. PIN BALANCE when the bottom sides of the screen are H.SIZE Adjust the display width (horizontal size). H. POSITION bowed towards left or right. Adjust the side pin corner balance bottom bowed towards left or right. V.SIZE Adjust the display height (vertical size). V. LINEARITY Adjust the vertical linearity. PINCUSHION Adjust the left and right margins for more convex or more concave margins. Adjust the trapezoid of the screen by moving the lines inward or outward. TRAPEZOID PIN BALANCE Adjust the side balance when the sides of the screen are bowed towards left or right. Adjust the parallelogram when the screen PARALLELOGRAM is leaning left or right. T. PIN CORNER Adjust the pin corner top when the top sides of the screen are bowed. COLOR TEMP Choose different preset color temperatures or set your own customized color parameters. RED GAIN Adjust the red gain. GREEN GAIN Adjust the green gain. BLUE GAIN Adjust the blue gain. RED BIAS Adjust the red bias. GREEN BIAS Adjust the green bias. BLUE BIAS Adjust the blue bias. LANGUAGE Select language for OSD (5 languages). B. PIN CORNER Adjust the pin corner bottom when the bottom sides of the screen are bowed. English - 8 English-9 Self Diagnosis ICON CONTROL FUNCTIONS DEGAUSS Degaussing keeps the monitor free from unwanted magnetism that can result in color impurity. STATUS Display horizontal & vertical frequency and polarity. H. MOIRE Adjust the horizontal picture moire cancellation. V. MOIRE Adjust the vertical picture moire cancellation. RECALL Reset the screen to the Factory Preset Display Settings. ROTATION Adjust the rotation when the screen is tilted left or right(Optional). English - 10 When the monitor doesn’t display, if you press any key, Self Diagnosis screen is displayed. Self Diagnosis function checks if the status of the monitor is No Signal or Out of range. No Signal screen is displayed when the D-Sub signal connector is not connected or the status of the monitor is on DPMS mode. Out of Range screen is displayed when the applied frequency is under or over normal range. Normal range H : 30 - 54 KHz V : 50 - 160 Hz English-11 SPECIFICATIONS TROUBLESHOOTING CDT Size Diagonal visible image area Dot Pitch Synchronization Horizontal Vertical Plug and Play Power Saving Power Source Power Consumption Dimension-W x H x D (set with stand) Weight-unpacked(lbs/Kg) Operating Temperature 15-inch 14-inch 0.28 mm 30 - 54 KHz 50 - 160 Hz DDC1/2B/CI EPA, VESA DPMS, Nutek Compliant 100-240 Vac, 50/60Hz (Free Voltage) 70 W 360 x 379 x 389mm Resolution (dots X lines) H.Freq (KHz) V.Freq(Hz) 640 X 480 31.5 60 Non-interlaced VESA VGA 75 640 X 480 37.5 75 Non-interlaced VGA 720 X 400 31.5 70 Non-interlaced VESA 46K 800 X 600 46.9 75 Non-interlaced VESA SVGA 85 800 X 600 53.7 85 Non-interlaced 1024 X 768 48.3 60 Non-interlaced VGA VESA 48K No picture. Check Check if power switch and computer power switch are in the on position. Check if the signal cable is correctly connected to the video card. Check if the pins of D subconnector are not bent. Check if the computer is in the power- saving mode. POWER LED is not Check if power switch is in the on position. lit. Check if the power cord is correctly connected. 26.2/11.9 10 ~ 40°C /50 ~ 104°F FACTORY PRESET TIMINGS Mode Symptom Remark Image is unstable. Check if the signal cable is suitable to the video card. Image is not centered, too small or too large. Adjust H &V Size or H&V Position to get the proper image. Picture bounces or a Keep the devices that may cause electrical wave pattern is interference away from the monitor. present in the picture. See the FCC information at the front cover of the manual. Color looks blotchy. Operate Degauss once. Picture is blurred. Adjust Contrast and Brightness. Operate Degauss once. Edges of available area on the screen are not straight. English - 12 Adjust Pincushion/Trapezoid/Pin Balance/ Parallelogram/Pin Corner Top/Pin Corner Bottom/ Pin Balance Top/Pin Balance Bottom. English-13 APPENDIX DESCRIPTION FOR D-SUB CONNECTOR Pin Signal 10 11 12 13 14 15 Red Green Blue GND GND GND-Red GND-Green GND-Blue +5Vdc GND-H.Sync GND-V.Sync Bi-directional Data(SDA) Horizontal Sync Vertical Sync(VCLK) Data Clock(SCL) 10 15 * GND=Ground S/N : 9978628100
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Create Date : 1999:12:06 11:34:23 Producer : Acrobat Distiller 3.01 for Power Macintosh Author : 7300 Creator : QuarkXPress3.3K: LaserWriter 8 8.3fc2 Title : 526X EN Modify Date : 2000:01:04 09:34:21 Page Count : 12EXIF Metadata provided by EXIF.tools