Manual
Operating Instructions
2.4G digital wireless receiver/transmitter
Pleasee read this manual thoroughly before operating the unit,
and keep it for future reference.
V1.4
Contents
1. Precautions....................................................................................1
2. Transmitter Features......................................................................2
3. Transmitter Technical Specications..............................................2
4. Receiver Features.........................................................................2
5. Receiver Technical Specications..................................................2
6. Parts Identication.........................................................................3
7. Application.....................................................................................4
8. Operation Instructions....................................................................4
- 1-
1. Precautions
Storage and Keeping
1. Do not expose the device to excessive heat or cold.The storage temperature of this device is
-30~+80OC,and the operating temperature is -20~+70OC.The humidity is Rh90﹪.
2. Avoid dropping or striking this device.
3. Avoid using this device in enclosed spaces,areas with excessive vibration or subject to
severe impacts.
4. Do not place cables where they may be pinched or stepped on.
5. The device is designed to be water-resistant,but not for underwater application.
Operating Precautions
1. The device may be powered by a 12 or 24 volt automotive battery or vehicle electrical system.
2. Make sure all cables are connected properly.Observe polarity.Improper cable connections may
damage the device.Remove the power cable connections when you do not intend to use the unit.
Warning
High voltage is present within the device.The opening of the case should be by professionals.
Special Notice
Never try to repair this device by yourself.In case of any problems,please turn off the device at once
and notify our company or authorized dealer.
Maintenance
Remove all cable connections from the device before cleaning the unit.
2
1. Remove all the cable connections from the monitor before cleaning the unit.
2. Use a mild household detergent and clean the unit with a slightly damp,soft cloth.
Never use strong solvents such as thinner or benzine, as they might damage the finish
of the device.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of sufficient magnitude to
constitute risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
You are cautioned that any changes or modifications not expressly approved in this manual could
void your warrantee and neccessitate expensive repairs.
CAUTION
This symbol is intended to alert the user not to waste electrical and electronic
equipment.
Declaration of conformity
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
interference that may cause undesired operation.
Maintenance
11
When auto dim is turned on in dark environment, OSD turns into dim mode for
dim setting ; When auto dim is turned on / off in bright environment, OSD display
normal mode.
PICTURE
DIM BRIGHT
DIM CONTRAST
DIM COLOR
VOLUME
AUTO DIM
SCALE ADJUST
40
45
40
50
ON
OFF
Press to select SCALE ADJUST.
PICTURE
BRIGHT
CONTRAST
COLOR
VOLUME
AUTO DIM
SCALE ADJUST
Press +/- to select or for scale adjustment↑↓. ↑↓
Exit menu and again press to display the grid line.
If ↑↓ is selected, press +/- to adjust the scale up/down; I f
Dim mode
PICTURE
AUTO DIM
SCALE ADJUST
BRIGHT
CONTRAST
COLOR
VOLUME
50
50
50
ON
OFF
Normal mode
50
50
50
50
50
OFF
OFF
is selected,
press+/-to adjust the scale left/right.
↓
↓↓
↓
↓↓
↓
↓↓
↓
↓↓
↓
↓↓
↓
↓↓
- 2-
2. Transmitter Product Features
1. 2.4G digital wireless transmitter
2. Power supply: 12v-32v
3. Supply 12v voltage for camera
4. Metal housing,solid,suitable for outdoor use
5. Waterproof protection level equals to IP67
6. Indication:
Power: power on the transmitter, and the light is on red
Code-match: press “PAIR” button, and the blue light is twinkling
Correct code-match: the blue light is on and does not twinkle.
3. Transmitter Technical Specications
1. Power supply: DC 12-32V
2. TV System: PAL: 25f/s NTSC: 30f/s
3. Operation frequency: 2400 -2483.5MHz
4. Line of Slight Range: 120M
5. Video Codec: MPEG4
6. Out Power:18dBm
7. RF Bit Rate: 6Mbps
8. Spread spectrum:FHSS
9. Hopping Rate: 1200/S
10. Latency: 200mS
11. Operating Temperature: -20 ~ +70OC RH90﹪
12. Storing Temperature: -30 ~ +80OC RH90﹪
4. Receiver Product Features
1. 2.4G digital wireless receiver
2. Power supply: 12v-32v
3. Metal housing,solid,suitable for outdoor use
4. Waterproof protection level equals to IP69K
5. Indication:
Power: power on the receiver connecting with selected monitor 4-pin male, and the light is on red
Code-match: press “PAIR” button, and the blue light twinkles
Correct code-match: the blue light is on and does not twinkle.
5. Receiver Technical Specications
1. Power supply: DC 12-32V
2. TV System: PAL: 25f/s NTSC: 30f/s
3. Operation frequency: 2400 -2483.5MHz
4. Line of Slight Range: 120M
5. Video Codec: MPEG4
6. Receiving Sensitivity: -86dBm
7. RF Bit Rate: 6Mbps
8. Spread spectrum:FHSS
9. Hopping Rate: 1200/S
10. Latency: 200mS
11. Operating Temperature: -20 ~ +70OC RH90﹪
12. Storing Temperature: -30 ~ +80OC RH90﹪
- 3-
6. Parts Identication
Transmitter
Receiver
“PAIR"Button
“PAIR"Button
Antenna
Antenna
Power
4PIN Male
4PIN Female
- 4-
7. Application:
8. Operation Instructions:
Please refer to operation diagram:
Connect transmitter with camera, red light of transmitter will flash. Connect receiver with monitor,
switch monitor’s channel to that of receiver’s. Red light of receiver will ash. Then “Wait Tx Signal…”
shows on screen.
Long press button “PAIR” of receiver for 3s-5s until blue light ashes. “PAIRING START xx” (xx is for
one minute countdown time) shows on screen. Then long press “PAIR” of transmitter for 3s-5s until
blue light ashes. When two blue lights ash at the same time, pairing is on and will complete within
1s~10s, then “SAVE DATA” shows on screen, and switch to camera’s image automatically.
When pairing completes, blue light and red light of both receiver & transmitter are on long light. Image
shows on monitor.
Blue
Brown
White
Black 4 pin male
Black
Red
Black 13 pin female
Black 13 pin male
Monitor
Camera
Battery
Battery
Camera
Receiver WR-096
Transmitter WT-434
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
This device complies with part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Note: Modifications to this product will void the user’s authority to operate this equipment.