Wacom Co DTZ2000W LCD Tablet User Manual users manual

Wacom Co Ltd LCD Tablet users manual

users manual

Introduction and overview Page 1 INTRODUCTION AND OVERVIEW The Wacom ® Cintiq ® DTZ-2000 pen display combines the benefits of an LCD monitor with the control, comfort, and productivity of Wacom’s cordless, battery-free pen technology. This gives you a direct pen-on-screen interface that can be used with a Personal Computer (PC) or Macintosh ® computer.Cintiq’s basic components include a Wacom pen tablet internally mounted behind a 20.1" wide format TFT color LCD monitor, and Wacom’s Grip Pen.Cintiq comes with a modular display stand, which allows you to easily rotate the pen display to any orientation, and to adjust the incline of the working surface to any angle between 10 and 65 degrees. Refer to Unpacking your Cintiq on page 7 before setting up the Cintiq stand or unpacking the Cintiq pen display. Please follow all instructions carefully. This manual describes how to install the Cintiq hardware and software. It also describes how to use Cintiq, the Grip Pen, and the modular display stand. The information is common to Windows and Macintosh computers, and Windows screen captures are shown unless otherwise noted. Note that the computer treats the Cintiq pen display as two separate devices (the LCD monitor and the pen tablet). Therefore, the installation process is completed in two stages:• First install the Cintiq as a display.• Then install the Cintiq as a pen tablet.Both stages require hardware and software installations and adjustments. Please follow all instructions carefully. IMPORTANT: You MUST install the Wacom pen tablet driver software for full pen and tablet functionality, otherwise the Cintiq pen will only function as a mouse device and the extended pen and tablet features will not be available.The following kinds of information are not included with this product: information about your specific computer hardware or operating system, or information about your application software. Your best source for this information is the set of manuals and disks that came with your hardware, operating system, or application.For information on using the Wacom Tablet control panel to customize your pen display tablet and pen settings, refer to Customizing on page 32 and to the electronic Software User’s Manual. See also Learning more about Cintiq on page 35.To use the pressure-sensitivity of the Grip Pen with your favorite drawing application, refer to instructions in that application’s manuals. DTZ-2000_Manual.fm Page 1 Wednesday, December 27, 2006 9:37 AM
Precautions on use and handlingPage 2 PRECAUTIONS ON USE AND HANDLING Be sure to follow all instructions, cautions, and warnings found within this manual. Failure to do so could cause the loss of data or damage to your computer. Failure to do so could also void your warranty, in which case Wacom shall have no responsibility to repair or replace the product. Physical locationEnvironmentUsage W ARNING Do not use the Cintiq pen display in a facility control system that requires extremely high reliability; it may cause other electronic devices to malfunction, or other devices may cause the pen display tablet to malfunction. Where use is prohibited, power off Cintiq to prevent the possibility of it causing other electronic devices to malfunction. Wacom does not accept any liability for direct or consequential damages. For details, please refer to your Warranty located at the end of this manual. Temperature and Humidity • Operating temperature and humidity: 5˚ to 35˚C, 20 to 80% RH• Storage temperature and humidity: -10˚ to 60˚C, 20 to 90% RH C AUTION Do not use or store Cintiq where: • Temperature changes are severe or exceed specifications (e.g., outdoors or inside a vehicle).• The pen display, the Grip Pen, and the Cintiq stand are exposed to direct sunlight or heat from an appliance, or are exposed to water or any other kind of liquid. C AUTION Do not use Cintiq in a dusty environment; this may damage the unit. W ARNING Only use the power adapter that came with Cintiq. If a different type of power adapter is used, Cintiq will not work properly or may be damaged. Using a different type of power adapter also has the potential to result in fire. Use of a different power adapter will void your warranty. C AUTION Be sure to use a grounded power source when applying power to Cintiq.C AUTION Do not connect or disconnect the video or power cables while Cintiq or your computer are turned on; this may damage the LCD monitor or computer video card. In this case, Wacom shall have no responsibility to repair or replace the product. C AUTION This product is for use with a DVI or VGA video card; using an inappropriate video card may damage Cintiq. C AUTION Do not block the rear panel ventilation holes; this may overheat and damage the unit. When not using Cintiq for long periods of time, unplug the power adapter from the AC outlet. DTZ-2000_Manual.fm Page 2 Wednesday, December 27, 2006 9:37 AM
Precautions on use and handling Page 3 Handling W ARNING High Voltage. Do not open or disassemble the Cintiq pen display. There is a risk of electrical shock when the casing is open. This will also void your warranty and Wacom shall have no responsibility to repair or replace the product. W ARNING Do not operate the display stand incline adjustment levers when Cintiq is not mounted on the stand, and do not lift the stand by the adjustment levers; the stand is spring-loaded and may cause injury or damage if released without the weight of Cintiq on the stand. Improper operation may lead to physical injury or damage to the stand. W ARNING When moving Cintiq to a different location, either remove the display unit from the stand (see page 12 for details) and then move both items separately, use the lock screws to fix Cintiq to the stand (see page 56 for details), or hold onto both Cintiq and the stand to make sure that the stand does not separate from the display unit when moving them together. Before moving Cintiq, first adjust the stand to its full upright position; this will reduce the spring tension so that the stand will not accidentally release and snap shut. If the display unit is in landscape orientation, use one hand to grasp the bottom of the display and with your other hand grasp the back of the stand. Be sure to lift on both the display and the stand so that the stand will not separate from the display when moving Cintiq.If Cintiq is in portrait orientation or has been locked to the stand with the rotation lock screws (see page 56), the stand will not separate from the display unit and Cintiq can be safely lifted by grasping the display unit with both hands.Always follow the instructions on page 12 to remove the display unit from the stand. W ARNING If the LCD screen has been damaged, DO NOT touch any liquid that may be leaking from it; this liquid is an irritant. In case of contact with skin, eyes, or mouth, rinse immediately with running water for at least 15 minutes or more. If contact is made with the eyes or mouth, also consult a physician. W ARNING – LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. The Cintiq pen display has a backlight which contains mercury (Hg). Be sure to dispose of properly, and to manage any disposal of this unit in accordance with your local ordinances and laws. W ARNING Do not disassemble the Cintiq stand. Improper disassembly could result in physical injury or damage to the stand. In this case, Wacom shall have no responsibility to repair or replace the product. W ARNING Prevent children from swallowing the pen tip or side switch. The pen tip or side switch may accidentally be pulled out if children are biting on them. C AUTION Do not disassemble the Grip Pen. This may cause the device to malfunction. In this case, Wacom shall have no responsibility to repair or replace the product. C AUTION Do not scratch the display screen. Avoid placing sharp objects on the display screen surface. C AUTION Avoid intensive shock or vibration to Cintiq, the Cintiq stand, or the Grip Pen. Hitting or dropping Cintiq may damage the display screen or other components.Hg DTZ-2000_Manual.fm Page 3 Wednesday, December 27, 2006 9:37 AM
Precautions on use and handlingPage 4 C AUTION Do not put heavy articles on the pen display or push against it with a strong force; this may damage the display screen or break the Cintiq stand locking mechanism. C AUTION Do not place heavy articles on the Cintiq cabling, repeatedly bend the cables sharply, or apply heavy stress to the cable connectors; this may damage the unit or cabling. C AUTION Do not store the pen display tablet on a surface that would excessively bend or crimp the cable.C AUTION If the pen tip becomes sharp or angular, it may damage the coating on the display screen. Please replace the pen tip if necessary. C AUTION Do not use any organic solvent (e.g., alcohol) or even mild detergent to clean the display screen. Use of these cleaners can damage the coating on the screen. Please note that damage of this kind is not covered by the manufacturer's warranty. • To clean the display screen, use an anti-static cloth or a slightly damp cloth. When cleaning, apply only a light amount of pressure to the display screen and do not make the surface wet.• To clean the Cintiq casing, Cintiq stand, or Grip Pen, use a soft cloth with mild detergent (such as dish washing liquid) diluted with water. C AUTION Do not expose Cintiq to high voltage electrostatic discharges or to a build-up of an electrostatic charge on the LCD screen. This may result in a temporary discoloration and blotching of the LCD monitor. If discolorations occur, leave Cintiq’s display on and the discolorations should disappear within a few hours. Reuse, recycling, and recovery. You are urged to recycle this product when replacing it with a newer product or when it has outlived its useful life by bringing it to an appropriate collection point for recyclable materials in your community or region. By doing this, you can help improve the environment of your community as well as minimize the potential negative effects created should any hazardous substance that may possibly be present within waste material reach the environment during the disposal process.Within the European Union, users are required not to dispose of Waste Electrical and Electronic Equipment (WEEE) as unsorted municipal waste, according to the Directive 2002/96/EC of the European Parliament and of the Council of 27 January 2003, or the corresponding local laws of the Member States. Products for which this is applicable will be marked with the WEEE symbol shown at the beginning of this note unless this is not feasible because of the size or the function of the product. Wacom products are subject to the Directive 2002/96/EC and therefore you should always collect them separately and bring them to the appropriate collection point in your community or region.Wacom pen display products (Cintiq series) comply with the European Union RoHS Directive 2002/95/EC (RoHS Directive). DTZ-2000_Manual.fm Page 4 Wednesday, December 27, 2006 9:37 AM
Contents Page 5 CONTENTS Introduction and overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Precautions on use and handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Physical location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Unpacking your Cintiq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Setting up the Cintiq stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Unpacking and mounting the Cintiq pen display . . . . . . . . . . . . . . . . 9Cintiq pen display components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Step 1: LCD monitor installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Step 2: Pen tablet installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Working with your Cintiq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Using the pen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Working with the tablet controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Setting up your work area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Customizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Opening the control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Customization basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Adjusting the LCD monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Testing Cintiq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41Testing your input tools and pen display controls . . . . . . . . . . . . . . 43Display troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Pen tablet troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47Technical support options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Obtaining driver downloads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 DTZ-2000_Manual.fm Page 5 Wednesday, December 27, 2006 9:37 AM
ContentsPage 6 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Caring for Cintiq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Optional display configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Using an alternate mount or stand . . . . . . . . . . . . . . . . . . . . . . . . . 57Pen and digital ink capabilities in Windows Vista . . . . . . . . . . . . . . 60Uninstalling Cintiq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61Product specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62Purchasing parts and accessories . . . . . . . . . . . . . . . . . . . . . . . . . 65Radio and television interference . . . . . . . . . . . . . . . . . . . . . . . . . . 66Warranty(Worldwide, Except for Europe, Africa and Middle East) . . . . . . . . 67 DTZ-2000_Manual.fm Page 6 Wednesday, December 27, 2006 9:37 AM
Unpacking your Cintiq Page 7 UNPACKING YOUR CINTIQ Package contents You will find parts and accessories packed together in the accessories box. To avoid damaging your product, please review the instructions on the following pages before setting up or using Cintiq or the Cintiq stand. Your product came with the following items: Notes: Images are not shown to scale. Some package configurations may include additional CDs or DVDs containing application software. To install these applications, review the instructions that came with those CDs or DVDs. Retain the package box for use when storing or shipping Cintiq. Next step: Set up the Cintiq stand. See page 8.Cintiq DTZ-2000 pen display, main unit with attached cablePower supply(POW-A100)andpower cableRotation lock screws (qty 2)(MNE-A067)Grip Pen with replacement nibs, pen stand, and nib removal set(ZP-501E, PST-A034, and FUZ-A131)Installation Guide & Hardware Manual (this manual)Wacom Pen Tablet Driver CD (contains the driver software)Cintiq stand (MST-A103) *PatentedParts and accessoriesVGA to DVI-I adapter (STJ-A252)DVI-D to DVI-I adapter (STJ-A253)Bearing hub recess cover plate and screws(PPL-A155 and NEM-A068) DTZ-2000_Manual.fm Page 7 Wednesday, December 27, 2006 9:37 AM
Unpacking your CintiqPage 8 Setting up the Cintiq stand Place the stand on your desktop or work surface, making sure the stand is stable and will not tip or fall when the pen display is mounted on it. Then familiarize yourself with the stand components. Next step: Unpack the pen display and mount it on the Cintiq stand. See page 9.Rear feetThe rear feet are on rollers, allowing the feet to move when adjusting incline.Bearing recessIncline adjustment leversWhen Cintiq is mounted on the stand, use these levers to adjust the display incline, as described in Adjusting the display incline on page 10.Front feetThe front feet have rubber pads to reduce stand slippage on the desktop when adjusting incline.WARNING Do not operate the incline adjustment levers when Cintiq is not mounted on the stand, and do not lift the stand by the adjustment levers; the stand is spring-loaded and may cause injury or damage if released without the weight of Cintiq on the stand. Improper operation may lead to physical injury or damage to the stand. Be careful to avoid catching your finger in the gap of the movable portion of the stand. DTZ-2000_Manual.fm Page 8 Wednesday, December 27, 2006 9:37 AM
Unpacking your Cintiq Page 9 Unpacking and mounting the Cintiq pen display Remove any packing materials from the back of the display unit and cabling.To mount Cintiq on the stand:• Make sure the stand is stable on your desktop or other work surface and will not tip or fall when Cintiq is mounted on it.• Securely grasp Cintiq with both hands so that the display faces toward you, with the power switch and LEDs located at the top.• Align Cintiq parallel to the front of the stand so that the bearing hub is located between the V-shaped upper edges of the stand’s bearing recess. See – A – (The V-shaped edges of the stand will serve as a guide for positioning the bearing hub.)• With the back of Cintiq resting against the stand, lower Cintiq until the bearing hub rests securely in the bearing recess of the stand. See – B – on the next page. The display unit will be held in place by gravity; there will be no audible ‘snap’ that indicates a mechanical lock. Note: If you do not need to rotate the Cintiq pen display, you may want to secure it to the stand with the rotation lock screws. For information on this, see Optional display configurations on page 56. To learn about other mounting options, see Using an alternate mount or stand on page 57.Bearing hubBearing recess– A – DTZ-2000_Manual.fm Page 9 Wednesday, December 27, 2006 9:37 AM
Unpacking your CintiqPage 10 Adjusting the display incline To adjust the display incline, face the front of the Cintiq pen display and grasp it on the left and right side at approximately the same height as the Cintiq stand adjustment levers. Use your fingertips to gently pull the incline adjustment levers toward the display unit; this will release the stand’s clutch mechanism. Tilt the display to adjust the incline setting.• To lower Cintiq, pull the left incline adjustment lever toward Cintiq and gently lower Cintiq to the desired incline angle. Release the lever to lock the stand in place.• To raise Cintiq, pull the right incline adjustment lever toward Cintiq and gently raise Cintiq to the desired incline angle. Release the lever to lock the stand in place. Note: The stand adjustment levers exhibit some natural play before the clutch mechanism engages. When adjusting the stand incline, set it slightly higher than you plan to work with, then lower the display to the desired position.– B –WARNING When operating the incline adjustment levers, Cintiq must be mounted on the stand with the stand feet resting on a stable, flat surface. The stand is spring-loaded and can snap back quickly, causing injury or damage if not operated properly.After the display unit has been mounted on the stand, remove the foam blocks that lock the adjustment levers in place. Save these blocks with the other packaging materials; you will need them if in the future you want to ship Cintiq.WARNING Before moving Cintiq, first adjust the stand to its full upright position; this will reduce the spring tension so that the stand will not accidentally release and snap shut. If the display unit is in landscape orientation, use one hand to grasp the bottom of the display and with your other hand grasp the back of the stand. Be sure to lift on both the display and the stand so that the stand will not separate from the display when moving Cintiq. If Cintiq is in portrait orientation or has been locked to the stand with the rotation lock screws (see page 56), the stand will not separate from the display unit and Cintiq can be safely lifted by grasping the display unit with both hands. DTZ-2000_Manual.fm Page 10 Wednesday, December 27, 2006 9:37 AM
Unpacking your Cintiq Page 11 Adjusting rotation The pen display can be rotated on the display stand when the incline is less than or equal to 25 degrees.To adjust rotation, grasp Cintiq by the main body and rotate the unit to the desired position; it will move on the bearing hub. You can only rotate the display unit 180 degrees in either direction. If you do not plan to rotate the Cintiq, use the rotation lock screws to fasten the display to the stand in a horizontal position. See Optional display configurations on page 56 for more information. Using the pen holder The integrated pen holder is located at the back of the pen display tablet. Note: The pen holder is not available for use when routing the cable to exit through the top cable opening.Next step: Go to page 13 and familiarize yourself with the pen display.DTZ-2000_Manual.fm Page 11 Wednesday, December 27, 2006 9:37 AM
Unpacking your CintiqPage 12Removing Cintiq from the display standTo remove Cintiq from the display stand:• If the rotation lock screws are attached, remove them from the back of Cintiq.• Position the pen display to landscape orientation before removing it from the display stand. The stand will not release unless Cintiq is in landscape orientation.• Next, raise the stand incline to the highest position. See Adjusting the display incline on page 10 for instructions.• Firmly grasp the pen display on both the left and right sides of the body, and lift the unit out of the display stand.Important: When removing Cintiq from the display stand, always lift Cintiq in a direction parallel to the front of the stand. You may also need to rotate Cintiq slightly so the stand will release.Note: When packing Cintiq for transport, first adjust the stand to its lowest position and place the foam packing blocks under the incline adjustment levers before removing Cintiq from the stand. The foam blocks will keep the stand from snapping shut while in its packaging. Always pack Cintiq and its stand in their original containers and protective cushions. Never pack Cintiq while it is mounted on the stand; this may damage the unit or stand during transportation.DTZ-2000_Manual.fm Page 12 Wednesday, December 27, 2006 9:37 AM
Cintiq pen display components Page 13CINTIQ PEN DISPLAY COMPONENTSAfter the Cintiq pen display is safely mounted on the Cintiq stand, take some time to familiarize yourself with its features and components.The LCD monitor and tablet sensor function as an integrated input and output device. The LCD monitor supports resolutions up to 1680 x 1050 pixels at 16.77 million colors. The tablet sensor reports pen coordinates, pressure, tilt, switch, eraser, and other information.Front viewPower LEDLights blue when power has been supplied to Cintiq and a video signal is present.Glows orange when no video signal is detected by Cintiq. (e.g., Your computer is turned off, starting up, or has entered a power management mode in which video signals are not sent.)Power switchTurns power to the unit on or off.Status LEDLights blue when the pen is in the active area of the pen display tablet and the pen tip, eraser, or side switch are pressed. Note that the USB cable connector must be plugged into an active USB port and a video signal must be present before the LED will light.Integrated LCD monitor and tabletExpressKeysAll ExpressKeys can be customized to simulate modifier keys, keystrokes, and other frequently used functions. A display toggle function is also available, enabling you to toggle the screen cursor between the Cintiq pen display and your other displays. See Working with the tablet controls on page 25.ExpressKeysBy default, the upper ExpressKeys on each side of the pen display support a TOUCH STRIP MODIFIER function not available to the lower ExpressKeys.DTZ-2000_Manual.fm Page 13 Wednesday, December 27, 2006 9:37 AM
Cintiq pen display componentsPage 14Rear viewNext step: Installation. See page 15.Integrated pen holder and alternate cable exitThe pen can be stored here. If you are not using the Cintiq stand supplied with the unit, you can route the cable to exit from this location. See Using an alternate mount or stand on page 57.Digital/Analog (DVI/VGA) switchSet this switch for the video connection you will be using.Cabling and connectorsThe connectors on the integrated cable are for DVI-I video, USB data, and power.Bearing hubFits into the bearing recess on the Cintiq stand. Allows rotation of Cintiq, and easy mounting and removal from the stand.On Screen Display (OSD) controlsThese controls enable you to adjust a variety of display settings. See Adjusting the LCD monitor on page 36 for more information.Important: Always store the pen display on the Cintiq display stand or in its original packing carton when not in use. Do not store the display unit on a surface that would excessively bend or crimp the cable.Touch StripTouch StripSlide your finger over the Touch Strips to zoom, scroll, or perform custom keystroke actions. See Working with the tablet controls on page 25.Kensington security slotAllows easy attachment of a security cable.Pen tether attachment pointIf you will be using a pen tether, connect it to the attachment point located on either side of the unit.DTZ-2000_Manual.fm Page 14 Wednesday, December 27, 2006 9:37 AM
Installation Page 15INSTALLATION System requirementsBefore installing Cintiq, make sure your computer meets the following minimum system requirements:•PC. Windows Vista™, Vista x64, XP, XP x64, or 2000. DVI or VGA video connector, available USB port, and CD-ROM drive.•Macintosh. OS X, v10.3.9 or greater. DVI or VGA video connector, available USB port, and CD-ROM drive. ADC connectors require an ADC to DVI-I adapter, not included. (ADC to DVI-I adapters can be purchased at various retail outlets.)Cintiq supports both digital (DVI) and analog (VGA) video signals. If you are updating your video card, complete the video card hardware and software installation before connecting Cintiq. If you have another display that is compatible with your video card, you can connect that display to the card in order to verify the video card is operating correctly.Note: Cintiq can be used alone or with another display, such as a CRT monitor or LCD projector. To use Cintiq with another display, you will need two video cards or a video card with dual output. Depending on the capabilities of your video card and operating system, you may be able to set up Cintiq as a mirrored, extended, or independent display. Refer to your video card documentation for more information on its capabilities.When you are working with more than one monitor, Cintiq will map to the monitors based upon how your system is configured. By default, if you are in mirror mode, the pen tablet will map to the entire space on each display or monitor. Please refer to your hardware and operating system documentation for details on configuring your computer and operating system for use with multiple monitors.A display toggle function is available for use with multiple monitor systems. This enables you to toggle the screen cursor between the Cintiq pen display and your other displays. See Using the ExpressKeys on page 26 for more information.By using the VGA to DVI-I adapter, you can connect Cintiq to a VGA video card. However, connecting Cintiq to a DVI video card generally results in optimum performance because a digital video signal will display a better image and sharper text.There are two primary steps to the installation process:• Step 1: LCD monitor installation• Step 2: Pen tablet installationBe sure to follow ALL installation instructions carefully.DTZ-2000_Manual.fm Page 15 Wednesday, December 27, 2006 9:37 AM
InstallationPage 16Step 1: LCD monitor installationIn the first stage of the installation process, Cintiq is installed as a monitor on your system. As you work through the first stage of the installation process, please refer to the LCD monitor cabling diagram on page 18 when making cable connections.Important: Do not connect the USB data cable until instructed to do so.• Turn off your computer.Caution: Never connect or disconnect the video or power cables while your computer or Cintiq are powered on – this can damage the LCD monitor or video card.• If your computer has only one video connector, you will need to unplug your previous monitor. Determine if your computer has a digital (DVI-I or DVI-D) or analog (VGA) connector, and set the DIGITAL/ANALOG (DVI/VGA) switch located on the back of Cintiq for the video connection you are using. Move the switch toward the tablet edge for Digital (DVI-I or DVI-D), and move it toward the OSD buttons for ANALOG (VGA). See – A – in the connection diagram on page 18.• Follow the instructions below for your video connector. See – B – in the diagram on page 18.If you are connecting to a DVI-I connector, plug the Cintiq video cable into the DVI-I connector of your video card.If you are connecting to a DVI-D connector, plug the Cintiq video cable into the DVI-D to DVI-I adapter supplied with Cintiq, and then plug the adapter into the DVI-D connector on your video card.If you are connecting to a VGA connector, plug the Cintiq video cable into the VGA to DVI-I adapter supplied with Cintiq, and then plug the adapter into the VGA connector on your video card.DVI-I connectorDVI-D connectorVGA connectorDTZ-2000_Manual.fm Page 16 Wednesday, December 27, 2006 9:37 AM
Installation Page 17• Be sure to tighten the thumbscrews on the connectors.• Connect the power adapter to Cintiq. See – C – on the next page. Then connect the adapter’s power cable and plug the adapter into an AC outlet. See – D – If you are connecting to an Apple computer with one of the following video ports, you will need to use an adapter:If you are connecting to an ADC connector, you will need to obtain an ADC to DVI-I adapter. Plug the Cintiq video cable into the ADC to DVI-I adapter. Then plug the ADC adapter end into the ADC connector on your video card.If you are connecting to an Apple mini-VGA connector, you will need to obtain a mini-VGA to VGA adapter. Plug the Cintiq video cable into the VGA to DVI-I adapter (supplied with Cintiq). Plug the mini-VGA adapter into the computer’s mini-VGA port. Then plug the male and female VGA connectors together.These adapters can be purchased at various retail outlets.Apple ADC connectorMini-VGA portDTZ-2000_Manual.fm Page 17 Wednesday, December 27, 2006 9:37 AM
InstallationPage 18LCD monitor cabling diagramCintiq, rear view – B – Video cardDVI or VGARear panel of your computerDo not attach the USB data cable until instructed to do so.Power adapter– C – DC INputTo AC outletDVI-I connectorTo connect to a DVI-D connector, use the DVI-D to DVI-I adapter cable.To connect to a VGA connector, use the VGA to DVI-I adapter cable. – D – CAUTION Make sure your video card has a DVI or VGA connector, and that you correctly set the Cintiq Digital/Analog (DVI/VGA) switch for the video connector you are using.CAUTION Use only the power adapter that came with Cintiq; use of an improper power adapter may damage the unit.Do not connect or disconnect the video or power cables while Cintiq or your computer are turned on – this can damage the LCD monitor or computer video card.Make sure that the display refresh rate does not exceed 75 Hz (60 Hz for WSXGA).DIGITAL/ANALOG (DVI/VGA) switch– A – DTZ-2000_Manual.fm Page 18 Wednesday, December 27, 2006 9:37 AM
Installation Page 19• Turn on Cintiq. The power LED will light orange.• Next, turn on your computer.For Windows systems, Cintiq will automatically install as a default monitor. If you want Cintiq to be identified as a Cintiq display and if you want to install the color calibration profile for Cintiq, follow the instructions below to update the display driver for Cintiq:For Macintosh systems, a Cintiq color profile will be added to your computer’s color management system during the tablet software driver installation process. To activate this color profile for use with Cintiq, you may need to select the Cintiq DTZ-2000 profile in the system’s ColorSync Utility control panel. For more details, refer to the color management information in your operating system and application documentation.1. From the CONTROL PANEL folder, open the DISPLAY PROPERTIES control panel. • For Windows Vista, select ADJUST SCREEN RESOLUTION.• For other Windows versions, select the SETTINGS tab.Click the IDENTIFY button if you need help in determining which display corresponds to Cintiq. If you have more than one display, select the display for Cintiq then click the ADVANCED button.2. Select the MONITOR tab and click the PROPERTIES button.3. Select the DRIVER tab and click the UPDATE DRIVER button. The HARDWARE UPDATE WIZARD will display.4. Insert the Wacom Pen Tablet Driver CD. If the Wacom Tablet installation menu displays, close it.Windows Vista:• Select the option BROWSE MY COMPUTER FOR DRIVER SOFTWARE.• Enter the drive letter for the Wacom Pen Tablet Driver CD and click NEXT.• After the installation is complete, close the DISPLAY PROPERTIES control panel.Windows XP:• If the driver was not found, click the BACK button, then select the option INSTALL FROM A LIST OR SPECIFIC LOCATION (ADVANCED), and click NEXT.• Select the option DON’T SEARCH. I WILL CHOOSE THE DRIVER TO INSTALL and click NEXT.• Click the HAVE DISK button, enter the letter of your CD-ROM drive (e.g., E:\), and click OK.• If the HARDWARE INSTALLATION dialog box displays, click CONTINUE ANYWAY to accept the driver. After the installation is complete, click the FINISH button to close the Wizard and then close the DISPLAY PROPERTIES control panel.Windows 2000:• Follow the prompts selecting the default options.• If a signing warning dialog box displays, click YES to accept the driver. After the installation is complete click the FINISH button to close the Wizard and then close the DISPLAY PROPERTIES control panel.DTZ-2000_Manual.fm Page 19 Wednesday, December 27, 2006 9:37 AM
InstallationPage 20• As necessary, configure the display control panel settings for the proper size and color resolution. The maximum (native) resolution of the Cintiq DTZ-2000 is 1680 x 1050 pixels with 24 bit color. The display size and color resolution may be constrained by the capabilities of your video card. See the video card manufacturer’s documentation for details.• If you are using analog (VGA) mode, you may want to fine-tune the display. Please refer to Adjusting pitch and phase (VGA only) on page 39, and to Adjusting the LCD monitor beginning on page 36 for more information.For Windows: If you are using Cintiq as a secondary display, you may first need to enable Cintiq in your Display Properties control panel.• After the LCD monitor portion of Cintiq is working to your satisfaction, move on to Step 2: Pen tablet installation to install the pen tablet portion of Cintiq.For troubleshooting tips, please refer to page 41.Notes: Each Cintiq LCD panel is produced under very stringent quality standards. Production techniques cannot guarantee an absolutely perfect TFT display, and some panels may exhibit a certain number of pixels that show an incorrect color. Refer to the specifications on page 62 for more information.If an image has fine striping (such as screen stripes), it may appear to flicker or display a moiré pattern.Do not apply excessive pressure on the display surface, it may cause the appearance of a moiré or pooling pattern. If you notice this action, use less pressure on the display screen when working with the pen.When a still image is displayed for a long period of time, an after-image may remain for a short time. To prevent this, Wacom recommends using a screen saver or other power management feature.Important: To extend the life of the backlight, set your computer’s power management to turn off the display when it is not in use for an extended period of time.DTZ-2000_Manual.fm Page 20 Wednesday, December 27, 2006 9:37 AM
Installation Page 21Step 2: Pen tablet installationUSB cable installation Plug the USB connector into an available USB port on your computer or into a USB hub attached to your computer.Next, move on to the pen tablet Software installation on page 22. You must install the Wacom tablet driver software for full tablet functionality.Pen tablet cabling diagramYour computerTo CintiqTo USB portDTZ-2000_Manual.fm Page 21 Wednesday, December 27, 2006 9:37 AM
InstallationPage 22Software installationIMPORTANT: You MUST install the Wacom pen tablet driver software for full pen and tablet functionality, otherwise the Cintiq pen will only function as a mouse device and the extended pen and tablet features will not be available.To install the tablet software:• Save your work and close all open applications before installing the tablet software. Temporarily disable any virus protection programs.• Insert the Wacom Pen Tablet Driver CD into your computer’s CD-ROM drive. If the software installer menu does not automatically display, double-click on the INSTALL icon located on the CD.• Click on the INSTALL TABLET link and follow the prompts to install the driver software.• Reactivate your virus protection program.• After the software installation has been completed, make sure you can use your pen on the Cintiq display to move the screen cursor.When you place the pen tip on the display screen, the screen cursor should immediately jump to a corresponding position approximately beneath the pen tip. Lift the pen tip and place it on the display screen surface in a different location – the screen cursor should again jump to the new position. This is known as absolute positioning, and enables you to position the screen cursor without having to drag your pen across the display screen surface. To fine-tune the cursor-to-pen relationship, see Calibrating Cintiq on page 34.Be sure to check the Read Me file for late-breaking news. If you have trouble installing Cintiq, see the Troubleshooting section beginning on page 41 of this manual.Notes:• For Windows Vista, driver installation automatically activates the new pen input functions available within Windows Vista and Office 2007.• For Windows Vista and XP, user-specific preferences are supported. After logging in, each user can customize their personal settings in the Wacom Tablet control panel. Switching to another user will automatically load the settings for that user.• The Windows Vista log-in screen does not support screen cursor movement with the pen tablet. Use the arrow keys or a standard mouse to select the user name for logging in.Next steps:Be sure to adjust the pen display tablet calibration to precisely align the screen cursor position with the location of the pen tip. See Calibrating Cintiq on page 34.To learn more about using Cintiq, proceed to Working with your Cintiq on page 23.DTZ-2000_Manual.fm Page 22 Wednesday, December 27, 2006 9:37 AM
Working with your Cintiq Page 23WORKING WITH YOUR CINTIQUsing the penAs you work with Cintiq, you can rest your hand lightly on the display screen, just as if it were a drawing board or sheet of paper. The Grip Pen is cordless, battery-free, and sensitive to the tilt and pressure you exert upon it. Hold the Grip Pen as you would a normal pen or pencil. Make sure the DuoSwitch is in a convenient location where you can toggle it with your thumb or forefinger, but not accidentally press it while drawing. You can tilt the pen in any way that feels most comfortable for drawing.Pen componentsThe components of your Cintiq Grip Pen function in the following manner:Pen tip: The pen becomes activated as soon as it is brought within 5 mm (0.2 inch) of the pen display screen. This allows you to position the screen cursor or use the DuoSwitch without touching the pen tip to the display screen. When pressure is applied to the pen tip, the tip switch is turned on and the pen simulates a primary mouse button click. The tip click pressure can be adjusted in the Wacom Tablet control panel. By default, the tip function is set to CLICK.DuoSwitch: The DuoSwitch is programmable, and can be used to perform the same click and double-click functions as the tip switch. Toggle the DuoSwitch in either direction to activate the upper or lower button functions. You can use the DuoSwitch whenever the pen tip is within 5 mm (0.2 inch) of the tablet surface; you do not need to touch the pen tip to the tablet in order to use the switch. By default, the upper switch is set to DOUBLE CLICK and the lower switch is set to RIGHT CLICK.Eraser: When the eraser is brought within 5 mm (0.2 inch) of the display the tablet reports the pen location. Pressure information is reported as you press down on the eraser. By default, the eraser function is set to ERASE.Important: Only use a pen that is compatible with Cintiq, such as the pen that shipped with the unit, or any of the pens from the Intuos3 product line (see Accessories on page 64). Other pens may not function properly. Also, the Cintiq pen tip is specifically designed for use with the Cintiq pen display – the tips on other pens could damage the protective coating on the Cintiq display screen.Refer to Customizing on page 32 and to the electronic Software User’s Manual for information on customizing the pen settings.EraserDuoSwitch(side switch)Tip Switch(replaceable nib)Note: When the Grip Pen is not in use, place it in the pen stand, the pen holder, or lay it flat on your desk.To maintain the sensitivity of your pen, do not store the pen in a container where it will rest on its tip or eraser.DTZ-2000_Manual.fm Page 23 Wednesday, December 27, 2006 9:37 AM
Working with your CintiqPage 24Pen operationsThe basic methods of working with the pen are as follows:Pointing and selecting: Move the Grip Pen above the Cintiq display screen to position the screen cursor. The pen tip needs to be within 5 mm (0.2 inch) of the pen display tablet surface; you do not need to touch the tablet surface to move the screen cursor. The cursor jumps to the location where you place the pen (absolute positioning). Press the pen tip on the display screen to make a selection.Note: You will need to calibrate the pen display tablet to correctly align the screen cursor with the pen tip. (See Calibrating Cintiq on page 34.) If the screen cursor does not jump to a position close to the pen tip when you place the pen on the display screen, then the pen tablet driver may not be installed or is not loading. Install the pen tablet driver software if necessary. Otherwise, refer to Troubleshooting, beginning on page 41.Clicking: Tap the display screen once with the pen tip, or touch the pen to the display screen with enough pressure to register a click.Windows tip: You can make navigating with the pen easier by configuring Windows to select when the pen is over an icon and to launch the icon with a single click. To turn on this feature first open a folder.For Windows Vista, from the ORGANIZE pull-down menu choose FOLDER AND SEARCH OPTIONS.... From the GENERAL tab select SINGLE-CLICK TO OPEN AN ITEM (POINT TO SELECT).For other Windows versions, from the TOOLS pull-down menu choose FOLDER OPTIONS.... From the GENERAL tab select SINGLE-CLICK TO OPEN AN ITEM (POINT TO SELECT).Double-clicking: Press the upper side switch, or quickly tap the display screen twice in the same place with the pen tip. Double-clicking is easier when the pen is perpendicular to the tablet screen. Refer to the electronic Software User’s Manual for information on fine-tuning the double-click area.Dragging: Select an object, then slide the pen tip across the display screen to move the object.Using the side switch: The pen is equipped with a DuoSwitch. This switch has two programmable functions that can be selected by rocking the switch in either direction. You can use the DuoSwitch whenever the pen tip is within 5 mm (0.2 inch) of the tablet surface; you do not need to touch the pen tip to the tablet in order to use the switch. The upper switch is set to DOUBLE CLICK, and the lower switch is set to RIGHT CLICK by default.Drawing with pressure-sensitivity: The pen responds to the nuance and inflection of your hand movements, enabling you to create natural-looking pen and brush strokes within applications that support this feature. To draw with pressure, select a pressure-sensitive tool from your application’s tool palette. As you draw on the screen surface, use various amounts of downward pressure on the tip of the pen. Press lightly for thin lines or softer color. Press harder for thick lines or dense color.Drawing with tilt: As with pressure-sensitivity, the pen display tablet recognizes when you tilt the pen from vertical to incline positions. In supporting applications, tilt can be used to control line shape and thickness.Erasing: In supporting applications, the pen’s eraser works like the eraser on a pencil. In text applications, use the eraser to select text, then lift the eraser from the tablet to delete the text.DTZ-2000_Manual.fm Page 24 Wednesday, December 27, 2006 9:37 AM
Working with your Cintiq Page 25Working with the tablet controlsThe customizable ExpressKeys and Touch Strips enable you to speed up your workflow in graphics or other applications. While using the pen with your dominant hand, you can simultaneously use your other hand to operate the ExpressKeys or Touch Strip. For example, use the ExpressKeys to quickly change your tool properties, or slide your finger over the Touch Strip to quickly zoom in or out.ExpressKeysPress the keys to perform frequently used functions or keystrokes. By default, the ExpressKeys emulate keyboard modifier keys. In Photoshop, this provides quick access to the grabber hand and alternate tools. A display toggle function is also available for use on multiple monitor systems. This feature allows you to use your pen on the Cintiq pen display to navigate the screen cursor to any display on your system.See Using the ExpressKeys on page 26.ExpressKeysBy default, the upper ExpressKeys modify the function of the corresponding Touch Strip located directly behind the keys on the back of the Cintiq pen display.When you press a key that has been assigned to TOUCH STRIP MODIFIER, the Touch Strip function is changed according to the ExpressKeys setting in the Wacom Tablet control panel’s TOUCH STRIP tab. See Using the ExpressKeys on page 26 and Using the Touch Strips on page 28.Note that an ExpressKey set for TOUCH STRIP MODIFIER can only change the function of the Touch Strip located on the corresponding side of your Cintiq pen display.DTZ-2000_Manual.fm Page 25 Wednesday, December 27, 2006 9:37 AM
Working with your CintiqPage 26Using the ExpressKeysPress the ExpressKeys with your secondary hand to toggle between tools or change tool properties while using your primary hand to work with your pen on the display tablet surface.All ExpressKeys can be customized. The default settings were chosen to optimize your workflow in Photoshop and other graphics applications using the following modifier functions:Button 1: CTRL modifier key for Windows. COMMAND (Apple key) for Macintosh.Button 2: SHIFT modifier key.Button 3: ALT modifier key for Windows. OPTION modifier key for Macintosh.Button 4: SPACE key (spacebar).Button 5: DISPLAY TOGGLE. This option is available for use only on multiple monitor systems.Button 6: Left and right outer TOUCH STRIP MODIFIER. Enables you to change Touch Strip functionality.Button 7: Left and right inner TOUCH STRIP MODIFIER. Enables you to change Touch Strip functionality.The ExpressKeys are chordable. For example, pressing keys 1 and 3 together simulates CTRL+ALT in Windows, or COMMAND+OPTION on Macintosh systems.12341234By default, the outer ExpressKeys will modify the Touch Strip to adjust the maximum tool size setting in Photoshop. Application-specific settings can be added to customize the keys for working with other applications.556776DTZ-2000_Manual.fm Page 26 Wednesday, December 27, 2006 9:37 AM
Working with your Cintiq Page 27The ExpressKeys enable you to speed up many common tasks. You can work with the default settings, or choose from any of the other available functions. For example:• Quickly change the functionality of a Touch Strip by first pressing a corresponding ExpressKey that has been customized for the TOUCH STRIP MODIFIER function and then using the Touch Strip.• On multiple monitor systems only, set an ExpressKey or a pen side switch to DISPLAY TOGGLE. You can then press that button to toggle the screen cursor between the Cintiq pen display tablet and your other displays. For example, Cintiq can be used as a pen display where the screen cursor is positioned at the pen tip location, or toggled for use as a standard Wacom tablet where the screen cursor can be moved across the entire desktop or additional displays.• In Photoshop, pressing the spacebar (key 4 on your pen display tablet) switches the currently selected tool to the hand tool and lets you pan (move) the image within the application window.• In Photoshop and many other graphics applications, the ALT, CTRL, and SHIFT modifier keys modify a tool or switch to a complementary tool while the modifier key is pressed.Tips: • Set a pair of keys to commonly used keystrokes, such as [ and ] to decrease and increase your brush size in Photoshop.• Set a key to a commonly used keyboard shortcut in order to open files or start an application.• If you prefer not to (or cannot) use the side switches on your Grip Pen, then set a key to right- or double-click.See the electronic Software User’s Manual for more details on the available key settings.DTZ-2000_Manual.fm Page 27 Wednesday, December 27, 2006 9:37 AM
Working with your CintiqPage 28Using the Touch StripsThe customizable Touch Strips can be operated in several different ways:•Standard operation: Slide your finger up or down to zoom, scroll, or issue the assigned keystroke function.•Continuous operation: Press and hold your finger at either end of the Touch Strip to continuously scroll. This is useful for scrolling through long documents or web pages.•Single step operation: Press and release your finger at either end of the Touch Strip to zoom, scroll, or issue the assigned keystroke function one step at a time.By sliding your finger over the Touch Strip you can quickly zoom in or out, scroll up or down, or perform other functions. You can do this with your secondary hand while using your primary hand to work with the Grip Pen. Each Touch Strip can also be set to issue custom keystrokes. For example, you might set a Touch Strip action to change brush sizes or cycle through layers when working in Photoshop. By default, the Touch Strips enable you to zoom in most graphics applications and to scroll in other applications.Press and hold here for continuous operation, or press and release for single step operation.DTZ-2000_Manual.fm Page 28 Wednesday, December 27, 2006 9:37 AM
Working with your Cintiq Page 29•Touch Strip Modifier operation: The upper pair of ExpressKeys located to the left and right of your pen display enable you to modify the function of the corresponding Touch Strip.Each Touch Strip can be independently customized to meet your needs.Tip: Photoshop users who frequently change brush sizes may want to assign the [ and ] keys to a Touch Strip. Sliding your finger up or down the Touch Strip will then change the brush size without the need to reach for the keyboard or access the Photoshop BRUSHES palette. This is the default setting for the Touch Strip when pressing the outer ExpressKey in each upper pair group.Refer to the electronic Software User’s Manual for detailed information on customizing the way your display tablet Touch Strips work.To modify the Touch Strip function:1. Press and hold the ExpressKey.2. Then slide or press your finger on the Touch Strip.Note: In the Wacom Tablet control panel, the ExpressKey must be set to TOUCH STRIP MODIFIER in the EXPRESSKEYS 2 tab and an alternate function must be defined for that ExpressKey in the TOUCH STRIP tab.DTZ-2000_Manual.fm Page 29 Wednesday, December 27, 2006 9:37 AM
Working with your CintiqPage 30Setting up your work areaThe Cintiq DTZ-2000 pen display and stand were designed to provide you with the widest possible range of flexibility and ergonomic work approach. The design allows you to quickly adjust Cintiq to a different position whenever the need arises. You may want to experiment with different height adjustments to determine which best fits your particular working style and tasks.As you work with Cintiq, you can rest your hand lightly on the display screen, just as if it were a drawing board or sheet of paper.To minimize fatigue, organize your work area so you can work comfortably. Position Cintiq, the Grip Pen, and your keyboard so they are easily accessible without unnecessary reaching. The pen display tablet and any other monitors should be positioned so you can view them comfortably with a minimum of eyestrain.Here are some other points to keep in mind:• Take short breaks between tasks to stretch and relax your muscles.• Use a gentle grip when working with the pen.• Alternate tasks throughout the day.• Minimize awkward postures and repetitive movements that cause discomfort.• Alternate between different modes of use.Note: Wacom makes no representation, promise or guarantee that Wacom products will cure or prevent, in whole or in part, mouse-induced repetitive stress symptoms, injuries or conditions. Individual results may vary. Always obtain competent medical advice to determine the most appropriate treatment for your specific situation.By adjusting the Cintiq stand to its lowest position, the pen display unit can be freely rotated on the display stand without touching the desktop. In this position, Cintiq emulates a traditional animator’s table and gives you the freedom to rotate the display unit to any angle for the greatest comfort and accuracy of stroke while drawing or editing images.Adjusting the Cintiq stand to its highest position is common when your work requires a large amount of keyboard input. This position is also useful when presenting your work to co-workers or clients.DTZ-2000_Manual.fm Page 30 Wednesday, December 27, 2006 9:37 AM
Working with your Cintiq Page 31Hints:• If the rotation lock screws are attached to the back of Cintiq, they must be removed before Cintiq can be rotated.• Before rotating the display unit, be sure the cable is freely rotating behind the unit.• Because the Cintiq drawing surface will be a little higher than your desk, consider adjusting the height of your desk or chair to assure comfortable use of the device.• Maintain a good posture at all times, and change your position if you feel any discomfort due to your work position.• Do not pull the cable out of its computer connections by accidentally moving the pen display tablet too far from the computer.• An optional pen tether can be used to ensure your pen stays with your pen display tablet.Note: Cintiq can also be mounted to articulated arms or other third-party stands meeting the VESA 100 specification for monitor stands. See Using an alternate mount or stand on page 57 for details.Next step: If you have not already done so, learn about the basics of customizing the Grip Pen. See Customizing on page 32.DTZ-2000_Manual.fm Page 31 Wednesday, December 27, 2006 9:37 AM
CustomizingPage 32CUSTOMIZINGAfter you master the basics of using your Grip Pen on the Cintiq pen display, you may want to customize the way the pen or pen display works. The Wacom Tablet control panel makes it easy to customize Cintiq and the pen.Opening the control panelTo open the control panel, use the Cintiq pen on the pen display tablet:Windows. Click on the Windows START button and choose ALL PROGRAMS. (For Windows 2000, choose the PROGRAMS group.) Then select WACOM TABLET and choose the WACOM TABLET PROPERTIES option.Macintosh. Open SYSTEM PREFERENCES from either the Dock, the Apple menu, or from the APPLICATIONS folder. Then click on the WACOM TABLET icon.After opening the control panel, see Customization basics on page 33.DTZ-2000_Manual.fm Page 32 Wednesday, December 27, 2006 9:37 AM
Customizing Page 33Customization basicsThis manual only covers the basics of customizing Cintiq. For detailed information see the Cintiq Software User’s Manual. If you installed the Wacom tablet software, just open the Wacom Tablet control panel and click on the HELP button to display the manual. You can also access the manual from the Installation menu on the Wacom Pen Tablet Driver CD.Open the Wacom Tablet control panel to customize your product. When you open the control panel, an icon for the Grip Pen is displayed in the TOOL list and the appropriate tabs are displayed. To customize the pen, make your changes to the tab controls. Experiment with different settings to find what works best for you. Any changes you make will take effect immediately, but you can always click DEFAULT to return to the factory settings.Tool Tips are available for most control panel items. Simply position the screen cursor over an item and let it rest there; in a few moments the Tool Tip will pop up. Additionally, your keyboard tab and arrow keys can be used to navigate the control panel.Note: Application-specific settings are for advanced users. This topic is covered in the Cintiq Software User’s Manual.Displays the electronic Software User’s Manual.Closes the control panel.Displays a dialog box containing information about the tablet and tablet software, including an option to access the DIAGNOSTICS dialog box.Choose FUNCTIONS to customize your ExpressKeys, Touch Strips, and Pop-up Menu settings.Choose GRIP PEN to customize your Grip Pen settings.The upper portion of the control panel displays icons representing your TABLET, TOOLs, and the APPLICATIONs with customized tool settings.Tabs display customizable settings for the selected tool.Displays advanced options.The DEFAULT button resets the selected tab to its default settings.DTZ-2000_Manual.fm Page 33 Wednesday, December 27, 2006 9:37 AM
CustomizingPage 34Calibrating CintiqYou will need to calibrate the pen display tablet in order to align the screen cursor position with the position of the pen on the display screen. This is required to adjust for parallax caused by the display screen cover glass and coating. Set Cintiq in its working position, then follow the procedure below. Important: When using a VGA connection with Cintiq, make sure the LCD monitor is properly adjusted before calibrating the tablet. See Adjusting pitch and phase (VGA only) on page 39, and Adjusting the LCD monitor beginning on page 36.• In the Wacom Tablet control panel, select the Grip Pen from the TOOL list and then select the CALIBRATE tab.• If you are working with multiple monitors, select the MONITOR option corresponding to the Cintiq display. (Only monitors that are set to one of the resolutions supported by Cintiq will appear in the list.)• Click on the CALIBRATE... button to activate the calibration screen.• Hold the pen and position your head as you normally do when working with the tablet. Use the pen tip to click on the center of the crosshairs in the upper-left corner.• Then click on the center of the crosshairs that are displayed in the lower-right corner.• Test the alignment by positioning the pen at a few different points on the display. Click OK to accept the calibration. Click TRY AGAIN to recalibrate.Be sure to read the directions in the calibration screen for detailed instructions and additional options. The calibration setting applies to all applications.Note: If more than one pen display tablet is installed on your system, be sure to select the Cintiq unit you are working with from the control panel’s TABLET list.CrosshairsAdjustment pattern for pitch and phase. See Adjusting pitch and phase (VGA only) on page 39 for details.Tip: If you prefer to see the screen cursor slightly offset from the actual position of the pen tip, calibrate by clicking on a spot showing that offset from the crosshairs. For example, to have the screen cursor appear 1/10th of an inch above and to the left of the pen tip, calibrate by clicking on a spot 1/10th of an inch below and to the right of the crosshairs.DTZ-2000_Manual.fm Page 34 Wednesday, December 27, 2006 9:37 AM
Customizing Page 35Learning more about CintiqRefer to the electronic Software User’s Manual for detailed information on customizing Cintiq.To view the manual, open the Wacom Tablet Control Panel and click on the HELP button.To read the Software User’s Manual before installing Cintiq, first insert the Wacom Pen Tablet Driver CD into your computer’s CD-ROM drive. When the software menu appears, select the USER’S MANUAL option.You will need Adobe Reader or another .pdf viewer to view the Software User’s Manual.DTZ-2000_Manual.fm Page 35 Wednesday, December 27, 2006 9:37 AM
CustomizingPage 36Adjusting the LCD monitorFactory presets, auto-sync, and user settingsFactory presets: For optimal display quality, set your video card to Cintiq’s native resolution of 1680 x 1050 pixels (WSXGA). See page 62 for signal specifications.Auto-sync: When connected as a VGA display, Cintiq attempts to automatically synchronize to the incoming signal. At the native resolution of 1680 x 1050, the vertical refresh frequency must be set to 60 Hz. For other resolutions, auto-sync will function when the horizontal frequency is between 30 to 82 kHz and the vertical frequency is between 50 to 75 Hz. If a specific resolution and vertical refresh frequency are not supported, you will see an “out of scan range” message. In this case choose a different resolution or refresh frequency. The auto-sync function automatically sets the horizontal and vertical screen position, as well as pitch and phase.If Cintiq does not automatically synchronize with the incoming signal, you can open the OSD menu, go to the RESET menu, and select the AUTO ADJUST option to initiate display synchronization. Additional screen display adjustments can be manually made using the OSD controls.User settings: When you manually adjust the display using the OSD function, the settings are stored within Cintiq for use the next time the unit receives a similar signal. This is applicable to all display modes.Working with on screen display settingsCintiq is equipped with an On Screen Display (OSD) function. The OSD function enables you to adjust and optimize a variety of display settings at the touch of a button. The OSD controls are located on the back of the unit. Simply reach over the top of the display unit to locate the buttons with your fingers.Note: Braille-style dots above the buttons help you to identify each one by touch.MENU buttonUse this button to open or close the OSD menu.Selection buttonsUse these buttons to select an option that can then be activated when you press the ENTER button.After activating a selected option, press the up button to increase a selected item value, and press the down button to decrease it.Digital/Analog (DVI/VGA) switch(up) (down)ENTER buttonActivates or deactivates the selected OSD menu option.DTZ-2000_Manual.fm Page 36 Wednesday, December 27, 2006 9:37 AM
Customizing Page 37The basic process for working with the OSD is as follows:• Press the MENU button to open the OSD main menu.• Use the up or down buttons to select an option. When the option you want to adjust is highlighted, press the ENTER button. The current settings and adjustment sub-menu for that option will appear.• Use the up or down buttons to adjust the option settings.• When you have made your changes, press the ENTER button to save. To exit, press the MENU button.Note: All settings are automatically saved when the OSD menu closes. If you make changes to the display appearance and cannot return to the original settings, use the RESET RECALL option to return Cintiq to its original factory defaults.When you open the On Screen Display (OSD), the following menu options are displayed as icons: CONTRAST. Select to increase or decrease image contrast.BRIGHTNESS. Select to increase or decrease image brightness.PHASE. (VGA only) Select to reduce or eliminate horizontal distortion lines. To automatically adjust, use the RESET option.PITCH. (VGA only) Select to reduce or eliminate vertical distortion lines. To automatically adjust, use the RESET option.HORIZONTAL CENTER. (VGA only) Select to move the screen image left or right. To automatically adjust, use the RESET option.VERTICAL CENTER. (VGA only) Select to move the screen image up or down. To automatically adjust, use the RESET option.MENU POSITION. Select to move the OSD menu around the display screen.LANGUAGE. Select to choose a language option for the OSD.DTZ-2000_Manual.fm Page 37 Wednesday, December 27, 2006 9:37 AM
CustomizingPage 38RESET. Provides two options.• Use AUTO ADJUST to reset only the image parameters.• Use RECALL to reset all screen options to the factory default.Selecting the exit icon exits the RESET window without resetting anything.SETUP. Select to adjust the display screen backlighting and OSD menu display options.BACKLIGHT. Increases or decreases the backlight brightness level.TRANSPARENCY. Adjusts the transparency of the OSD menu.TIME OUT. Sets the display time of the OSD menu, in seconds. COLOR. Provides settings for 9300˚, 6500˚, and 5000˚ Kelvin.DIRECT displays the colors directly from the video card without any adjustment. When selected, the BRIGHTNESS and CONTRAST settings are also set to DIRECT and cannot be adjusted manually.Also provides a CUSTOM option that enables you to adjust Red, Green, and Blue independently.Choose a setting to work with and press ENTER to activate your selection. Change the CUSTOM setting by selecting the enter icon.In the custom COLOR window, change Red, Green, or Blue to calibrate color. To exit, select the exit icon.Note: Manual changes to the color settings will invalidate the Cintiq color profile.SCALE. Enables you to choose how the image is displayed when working at resolutions below 1680 x 1050.FULL resizes the image to fill the whole screen. 1:1 displays the image at the actual resolution.ASPECT resizes the image to fill as much of the screen as possible while maintaining the correct aspect ratio.DTZ-2000_Manual.fm Page 38 Wednesday, December 27, 2006 9:37 AM
Customizing Page 39Adjusting pitch and phase (VGA only)Some computers and video cards may not allow the auto-sync function to fully work when Cintiq is first connected. If some portion of text appears blurred, open the OSD menu, go to the RESET menu, and select the AUTO ADJUST option. If the image is still blurred, adjust the pitch and phase manually by following the procedure below. For optimal display quality, set your video card to Cintiq’s native resolution of 1680 x 1050 pixels.• In the Wacom Tablet control panel, select the CALIBRATE tab.• If you are working with multiple displays, be sure the display corresponding to Cintiq is selected in the MONITOR menu.• Click on the CALIBRATE... button to activate the calibration screen.• Using the OSD controls, open the OSD menu and select the Pitch icon. Then adjust the pitch level so that the pattern of fine vertical stripes displays evenly. (For details on changing the OSD settings, see Working with on screen display settings on page 36.)• Next, in the OSD menu select the Phase icon and adjust the phase level so that the adjustment pattern shows clearly.• After completing these adjustments, press the ENTER and MENU buttons to exit the OSD menu.• Click on the CANCEL button or press ESC to exit the calibration screen.Adjustment pattern for pitch and phase.DTZ-2000_Manual.fm Page 39 Wednesday, December 27, 2006 9:37 AM
CustomizingPage 40Power savingCintiq conforms to VESA and ENERGY STAR® power saving guidelines.When using Cintiq with a Display Power Management Signaling (DPMS) compliant computer or video card, the display will automatically comply with the below power saving parameters.Computer mode H-sync V-sync Video Power consumption Power lampPower ON Yes Yes Active 50 W, max. BlueStandby mode No Yes Blanked 2 W, max. Orange/BlueSuspend mode Yes No Blanked 2 W, max. Orange/BlueOFF Mode No No Blanked 1 W, max. OrangeDTZ-2000_Manual.fm Page 40 Wednesday, December 27, 2006 9:37 AM
Troubleshooting Page 41TROUBLESHOOTINGMost of the time your pen display tablet will work flawlessly. But if you are having trouble, Wacom recommends you do the following:1. If Cintiq does not function properly, refer to the troubleshooting section below. See also Display troubleshooting on page 45, or look in the Pen tablet troubleshooting on page 47. Your problem may be described there and you can try the solution offered.2. Open the Wacom pen display Read Me file for late-breaking information.3. If you are having a compatibility conflict between Cintiq and a new hardware or software product, check if a newer pen tablet software driver is available. See Obtaining driver downloads on page 53 for information on downloading an updated software driver. Wacom periodically updates the software driver to maintain compatibility with new products.4. Check the FAQs (Frequently Asked Questions) on the Wacom web site for your region.5. If you have tried the suggestions in this manual and still cannot resolve the problem, then contact Wacom for Technical Support. See the Read Me file for information on where to obtain support for your region.Testing Cintiq1. If the Cintiq power LED does not light, check the following:• First verify that the green light on the power adapter is on. If the light is not on, check that the power cable is properly connected to the power adapter and to an active AC outlet.• Check that the power adapter cable is securely connected to the Cintiq power cable and that the Cintiq power switch is turned on. The Cintiq power LED will glow orange or blue whenever Cintiq is on.Important: Use only the AC adapter that came with your pen display. Other adapters may cause damage to your product.2. If there is no display:• Make sure that your computer is turned on. The power LED will light blue when the proper video signal is received, and orange if there is no video signal or if the computer is in a power saving mode.• Verify that Cintiq is connected to an active DVI-I, DVI-D, or VGA connector and that the DVI/VGA switch on the back of Cintiq is set to the correct video setting.• Check that your video card has been properly installed and is functional. If you have another display that is compatible with your video card, you can connect that display to the card in order to verify that the video card is operating correctly.DTZ-2000_Manual.fm Page 41 Wednesday, December 27, 2006 9:37 AM
TroubleshootingPage 423. Verify that the tablet and Grip Pen are working:• Press the Grip Pen tip against the display and verify that the status LED lights blue.• If the LED does not light, verify that Cintiq’s USB cable is plugged into an active USB port. If Cintiq is plugged into a USB hub, try plugging Cintiq directly into the USB port on your computer.• Be sure that the USB port to which you are connecting Cintiq has not been disabled. It may be necessary to check your system BIOS setting to verify that you have connected Cintiq to an active USB port.• The status LED will light blue when Cintiq is registered as a USB device and the pen tip is pressed against the display.4. Check the pen. If you cannot make a selection on the display screen with the pen:• Test the pen by pressing the pen tip or the eraser against the surface of the pen display tablet. The status LED should light blue.• Now, without applying pressure to the pen tip but keeping the pen within 5 mm (0.2 inch) of the pen display tablet surface, press the side switch. The status LED should again light blue.• If the status LED does not light blue for these tests, be sure you are using the correct pen that came with Cintiq.• See Testing your input tools and pen display controls on page 43 and Testing a pen on page 44 for more information.If you are still having problems, you may have a defective pen or pen display tablet.DTZ-2000_Manual.fm Page 42 Wednesday, December 27, 2006 9:37 AM
Troubleshooting Page 43Testing your input tools and pen display controlsIf the Grip Pen, or the Cintiq ExpressKeys or Touch Strips do not work as you expect, it is a good idea to first check the assigned functions or reset them to their default conditions. A quick way to reset a pen to its default settings is to remove it from the TOOL list by clicking on the list’s [ – ] button. After the pen has been removed, place it back onto the display screen surface and the pen will be re-added to the TOOL list with its default settings.Open the Wacom Tablet control panel and click on the ABOUT button. In the dialog box that appears, click on the DIAGNOSE... button to open the DIAGNOSTICS dialog box. The DIAGNOSTICS dialog box displays dynamic information about the Cintiq pen display tablet and pen. This information is used when testing Cintiq and your input tool(s).If more than one Cintiq unit is connected to your system, be sure to select the unit for which you are testing in the TABLET INFO column.Note: When testing your tool buttons, if a button is set to POP-UP MENU or OPEN/RUN..., that function will occur when the button is pressed. In this case you may want to change that button’s function before testing.Testing the ExpressKeys1. With the DIAGNOSTICS dialog box open, observe the TABLET INFO column as you test the ExpressKeys. If you have more than one Cintiq unit connected to your system, be sure to select the unit you are testing from the TABLET INFO column.2. Test the ExpressKeys by pressing them one at a time. Each time you press a key, its number will be displayed next to either the LEFT KEYS or RIGHT KEYS category, depending on which keys group you are testing.When you are done, click the CLOSE button to exit the dialog box.Testing the Touch Strips1. With the DIAGNOSTICS dialog box open, observe the TABLET INFO column as you test each Touch Strip. If you have more than one Cintiq unit connected to your system, be sure to select the unit you are testing from the TABLET INFO column.2. Slide your finger up or down along the entire length of the Touch Strip you want to test. As you touch and move your finger along the Touch Strip, a number will indicate the current finger position for the respective Touch Strip next to LEFT TOUCH STRIP or RIGHT TOUCH STRIP.When you are done, click the CLOSE button to exit the dialog box.DTZ-2000_Manual.fm Page 43 Wednesday, December 27, 2006 9:37 AM
TroubleshootingPage 44Testing a pen1. While observing the POINTING DEVICE INFO column, bring your pen within 5 mm (0.2 inch) of the display screen. A value for PROXIMITY, the DEVICE NAME, DEVICE TYPE, and a DEVICE S/N (serial number) should be displayed. If you have more than one Cintiq unit connected to your system, be sure to select the unit for which you are testing a pen in the TABLET INFO column.2. Move your tool along the tablet surface. The X and Y DATA values should change to reflect the tool position.3. Test your pen switches. The Cintiq status LED should light blue each time you click with the tool tip, press the side switch, or press the tool’s eraser to the display screen.• Press on the display screen surface with the tool tip – the SWITCHES state and PRESSURE value should change. (PRESSURE should change from approximately 0% with no pressure applied to approximately 100% when full pressure is applied.)• Next, press the side switch without pressing the tip to the tablet – the SWITCHES state should change. (For the Grip Pen, do this for both positions of the DuoSwitch.)• Press the tool’s eraser to the display screen – the SWITCHES state and PRESSURE value should change. (PRESSURE should change from approximately 0% with no pressure applied to approximately 100% when full pressure is applied.)• For the optional Airbrush, move the fingerwheel forward – the WHEEL value should decrease to a value of approximately 0 when the fingerwheel is all the way forward. Move the fingerwheel backward – the WHEEL value should increase to approximately 1000 when the fingerwheel is all the way back.4. Test tilt for the x-axis by moving the pen from a vertical position toward the right; the X TILT value should change from approximately 0 to +60. Now move the tool to the left of vertical; the X TILT value should change from approximately 0 to -60.5. Test the tilt for the y-axis by moving the pen from a vertical position toward the bottom of the tablet; the Y TILT value should change from approximately 0 to +60. Now move the tool toward the top of the tablet; the Y TILT value should change from approximately 0 to +60.6. For the optional 6D Art Pen, test the rotation feature by placing the pen tip on the display screen surface and slowing rotating the pen on its axis. The ROTATION value should change as you rotate the pen.7. When you are done, click on the CLOSE button to exit the dialog box.Pen Tip = 1, DuoSwitch (lower position) = 2, DuoSwitch (upper position) = 3, Eraser = 1Airbrush Tip = 1, Side Switch = 2, Eraser = 1DTZ-2000_Manual.fm Page 44 Wednesday, December 27, 2006 9:37 AM
Troubleshooting Page 45Display troubleshootingIf you encounter problems with the Cintiq display, refer to the following tables; your problem may be described here and you can try the solution offered. For additional information about color issues, refer to the documentation that came with your operating system or applications.General display problemsNo display. The power LED is off.• Verify that the light on the AC power adapter is on and the power cable is securely plugged into Cintiq’s power receptacle. Check that Cintiq’s power switch is turned on.No display. The power LED is lit blue.• Check the contrast, brightness, and backlight controls. Adjust as necessary, or open the OSD menu, go to the RESET menu and select the RECALL option.The power LED is lit orange.No display or a “no input signal” message briefly appears on your display screen.• Your computer may be in a power management mode. Touch the pen tip to the Cintiq display screen, move the mouse, or depress any key on your keyboard.• Turn off both your computer and the Cintiq pen display, and check the video cable for bent or broken connector pins. Then properly reconnect the video cable and turn on Cintiq and your computer.• Verify that the DIGITAL/ANALOG (DVI/VGA) switch is properly set. Restart your computer after changing the position of the switch.• Verify that the video card is properly installed.No display or a “cable disconnect” message briefly appears on your display screen.• Check that your computer is turned on.• Verify that the video cable is properly connected.• Turn off both your computer and the Cintiq pen display, and check the video cable for bent or broken connector pins. Then properly reconnect the video cable and turn on Cintiq and your computer.An “out of range” message briefly appears on your display screen.• The input signal frequency is incorrectly set or not compatible with Cintiq. Set the refresh rate (vertical frequency) to 60 Hz (or between 50 and 75 Hz if you are using a resolution of less than 1680 x 1050 pixels). If your video card driver supports adjustment of the horizontal frequency, make sure it is set to some value between 30 and 82 kHz. On a single monitor system you will need to connect a different display to change the refresh rate.• The resolution is set too high (1680 x 1050, maximum).• Set the display properties to detect plug and play monitors.The image appears multiple times on the display.• Do not extend the video cable. Do not use an input selector switch box.DTZ-2000_Manual.fm Page 45 Wednesday, December 27, 2006 9:37 AM
TroubleshootingPage 46VGA problemsWhen a still image is displayed for a long period of time without refreshing the screen, an after-image remains for a short period of time.• Use a screen saver or other power management feature.Color quality is inaccurate. • Open the OSD menu, go to the RESET menu and select the RECALL option.• Be sure the Cintiq color profile has been installed and is selected as the profile for use with your operating system and applications.• Any changes to the contrast setting should be made in small increments as changes in contrast may affect color accuracy.The color white does not display as white.• Be sure the Cintiq color profile has been installed and is selected as the profile for use with your operating system and applications.• Verify also that the display is operating at the factory default settings. If that is not sufficient, then adjust color as necessary. For details on color management, refer to your operating system and application documentation.• Verify that the video cable and connector are fully connected.The display ripples or flickers. • Open the OSD menu, go to the RESET menu, and select the AUTO ADJUST option. If necessary, manually adjust the pitch and phase settings.• Verify that the display adapter or video card matches the specifications for Cintiq.• Adjust the refresh rate in the Display Properties control panel.The display is not clear. Text or other portions of the screen appear blurred.• Set the display resolution of your video card to 1680 x 1050.• Turn off the Cintiq, then turn it back on.• Open the OSD menu, go to the RESET menu, and select the AUTO ADJUST option. If necessary, manually adjust the brightness, pitch and phase settings.The display and LCD panel are not lined up. The display size is not correct.• Open the OSD menu, go to the RESET menu, and select the AUTO ADJUST option. If necessary, manually adjust the pitch and phase settings.The display ripples or shows a moiré pattern. The display color is not even.• Open the OSD menu, go to the RESET menu, and select the AUTO ADJUST option. If this does not solve the problem, go to the RESET menu and select the RECALL option to set the display back to the factory default settings.• Open the OSD menu, and as necessary adjust pitch and phase.DTZ-2000_Manual.fm Page 46 Wednesday, December 27, 2006 9:37 AM
Troubleshooting Page 47Pen tablet troubleshootingIf you encounter problems with the Cintiq pen display tablet, refer to the following tables. Your problem may be described here, and you can try the solution offered. Be sure you refer to the Cintiq Read Me file for the latest information.For additional information, visit Wacom’s web site at http://www.wacom.com/productsupport and follow the links to the FAQs.General problemsThe computer does not have an available USB port.Check if there is an available USB port on a USB hub. If not available, you will need to add a USB hub or USB card.The pen display power LED is off.Make sure the pen display power switch is turned on.Check that the AC power adapter is plugged into both the pen display and an active power outlet and that the green light on the power adapter is on.Use only the power adapter that came with the pen display; other adapters may cause damage to your product.The pen works only in mouse mode, and does not draw with pressure-sensitivity.The tablet driver software was not installed or did not load properly. Make sure the tablet driver software is installed and functioning. Install the pen tablet driver software in accordance with the instructions found in the Installation section of this manual.The pen does not draw with pressure-sensitivity.Some applications require that you turn on the pressure capabilities within the application or selected tool before the pen will respond as a pressure-sensitive tool.Clicking is difficult. Open the Wacom Tablet control panel and go to the PEN tab. Try using a lighter TIP FEEL.The pen selects everything or will not stop drawing.Open the Wacom Tablet control panel and go to the PEN tab. Move the TIP FEEL slider toward FIRM, or select the DETAILS... button and increase the CLICK THRESHOLD setting. If this does not help, see Testing Cintiq on page 41.Double-clicking is difficult. Be sure you are quickly tapping the display screen twice in the same place on the pen display tablet’s active area. Wacom recommends using the side switch to double-click.Open the Wacom Tablet control panel and go to the PEN tab. Try increasing the TIP DOUBLE CLICK DISTANCE or using a lighter TIP FEEL.Windows: Try setting your system to launch programs with a single click. See Pen operations on page 24.DTZ-2000_Manual.fm Page 47 Wednesday, December 27, 2006 9:37 AM
TroubleshootingPage 48The eraser selects everything or will not stop erasing.Open the Wacom Tablet control panel and go to the ERASER tab. Move the ERASER FEEL slider toward FIRM, or select the DETAILS... button and increase the CLICK THRESHOLD setting. If this does not help, see Testing Cintiq on page 41.You notice a delay at the beginning of pen strokes.Open the Wacom Tablet control panel and go to the PEN tab. Try decreasing the TIP DOUBLE CLICK DISTANCE. If that does not work, try dragging the TIP DOUBLE CLICK DISTANCE slider to the OFF position in order to turn off double-click assist.You have to press hard with the pen when clicking or drawing.Open the Wacom Tablet control panel and go to the PEN tab. Move the TIP FEEL slider toward SOFT, or select the DETAILS... button and decrease the SENSITIVITY and CLICK THRESHOLD settings.The pen tip does not function.Be sure you are using the pen that originally came with your pen display tablet, or an Intuos3 pen. Other pens may not function properly on the Cintiq pen display.Make sure the status LED lights blue when the pen tip is pressed. If the LED does not light, verify that the USB cable is plugged into an active USB port on your computer or on a USB hub.If the LED still does not light, you may have defective hardware (see Troubleshooting on page 41).Open the Wacom Tablet control panel. Check the control panel’s PEN tab and verify that the tip is assigned to a CLICK function.Changing the function settings for an input tool has no effect.Make sure that you change the settings for the tool and application that you are using. See the electronic Software User’s Manual for details on working with multiple tools and with application-specific settings.The side switch does not work.Be sure you are using the pen that originally came with your pen display tablet, or an Intuos3 pen. Other pens may not function properly on the Cintiq pen display.Be sure you press the side switch when the pen tip is within 5 mm (0.2 inch) of the pen display tablet’s active area – do this without pressing down on the pen tip.From the Wacom Tablet control panel, verify that the side switch is set to the proper function you are expecting to occur for the application (and input tool) you are using. Check also which SIDE SWITCH MODE option is selected. (These options are accessed by clicking on the control panel OPTIONS... button.)Make sure the status LED lights blue when you press the side switch. If the LED does not light, verify that the USB cable is plugged into an active USB port on your computer or on a USB hub.If the LED still does not light, you may have defective hardware (see Troubleshooting on page 41).DTZ-2000_Manual.fm Page 48 Wednesday, December 27, 2006 9:37 AM
Troubleshooting Page 49The pen tip and screen cursor do not properly line up.Open the Wacom Tablet control panel and select the CALIBRATE tab. Continue with Calibrating Cintiq on page 34.The screen cursor moves but it does not jump to the pen tip location when the pen is placed on the display screen, and it does not follow the pen tip when the pen is moved across the display.Make sure the Wacom tablet driver has loaded properly by opening the Wacom Tablet control panel. If the driver did not load you will see an error message. If an error message appears, reboot your computer. If the problem persists, refer to the Installation instructions and reinstall the Wacom tablet software. (For Macintosh, you must restart your computer after installing the Wacom tablet driver for proper tablet operation.)If you have customized the side switch on your pen to toggle between PEN mode and MOUSE mode, make sure that your pen display tablet is operating in PEN mode.When using Cintiq on a multiple monitor system, you cannot use the pen to control the other monitor(s).To toggle the screen cursor between Cintiq and the other monitors connected to your system, press one of the ExpressKeys that has been set for the DISPLAY TOGGLE function. See the electronic Software User’s Manual for details on working with DISPLAY TOGGLE.You can also use your pen to control the other monitors in MOUSE mode. To use MOUSE mode, first set the pen’s DuoSwitch to MODE TOGGLE.... Then use the switch to toggle between PEN mode and MOUSE mode.The line you are drawing does not line up with the location of the screen cursor in paint applications.To function properly, some applications require that the pen is set to PEN mode. Make sure the pen has not been toggled to MOUSE mode.If the pen is set to PEN mode and the problem still exists, then you may have a corrupted preferences file. Follow the instructions in the next tip to create a new preferences file.DTZ-2000_Manual.fm Page 49 Wednesday, December 27, 2006 9:37 AM
TroubleshootingPage 50You suspect the pen tablet preferences may be corrupted, or want to make certain that all settings are at their factory defaults.Delete the pen tablet preferences as follows:Windows: Click the START icon and select ALL PROGRAMS. Then select WACOM TABLET and TABLET PREFERENCE FILE UTILITY. In the dialog box that appears, click on the REMOVE MY PREFERENCE FILE button to delete the preferences for the current user. To delete preferences for multiple users on Windows Vista or XP systems, click on the REMOVE ALL PREFERENCE FILES button. Note that administrator rights are required to delete preferences for all users. Relaunch any currently open tablet-aware applications that you may be running.Macintosh: For a single user, delete the tablet preferences by first choosing your HOME folder from the GO menu. Then open your home LIBRARY folder. Within your home LIBRARY folder, open the PREFERENCES folder and delete the COM.WACOM.TABLETPREFERENCES file. Log out, then log back in. When the tablet driver loads, it will create a new preferences file with the factory defaults.For multiple users, delete all tablet preferences by first opening the main APPLICATIONS folder. Then open the TABLET folder and run the REMOVETABLET utility. When the utility starts, click on the REMOVE ALL PREFERENCE FILES button. Log out, then log back in. When the tablet driver loads, it will create new preferences files with the factory defaults.Recalibrate the tablet.Note: Do not manually remove the WACOM TABLET.PREFPANE file from the main LIBRARY PREFERENCEPANES folder. This file is only to be removed when uninstalling the tablet software driver, and then only when using the REMOVETABLET utilityThe screen cursor moves erratically or jumps around on the display screen when another tablet is connected to your computer.The tablet portion of Cintiq emits electromagnetic waves at a certain frequency. If another tablet is too closely placed to Cintiq it may interfere with screen cursor positioning. If this occurs, move the tablet further away from Cintiq.Cintiq has stopped working. The pen no longer turns the status LED blue, or the status LED is always blue.The tablet portion of Cintiq may need to be recalibrated to regain normal function. Do not uninstall the driver or delete the tablet preferences. Contact the Wacom support staff for the area where your product was purchased. See the Wacom tablet Read Me file, located on your computer or on the Wacom Pen Tablet Driver CD, for contact information.DTZ-2000_Manual.fm Page 50 Wednesday, December 27, 2006 9:37 AM
Troubleshooting Page 51Windows-specific problemsMacintosh-specific problemsAfter changing right- and left-handed settings in the computer’s mouse control panel, the pen tip no longer functions properly.Restart Windows for your Wacom tool settings to be correctly recognized.At startup, a dialog box appears telling you that either the driver failed to load or the tablet preferences have not yet been created.The pen display tablet was not detected at startup. Check that the USB interface cable is securely connected to an active USB port on your computer. Make sure also that Cintiq’s power light is on and is glowing blue. If your pen display tablet is plugged into a USB hub, make sure the hub is connected and active. If this does not correct the problem, see Troubleshooting on page 41.From the GO menu, select the UTILITIES folder and launch the SYSTEM PROFILER. Select USB from the HARDWARE section of the CONTENTS list. A Wacom USB pen display tablet model should be listed. If a pen display tablet model is not listed, check the pen display’s USB cable connection or try plugging the pen display into a different USB port.If this does not help, contact Wacom for Technical Support. See Technical support options on page 52.Inkwell does not work correctly with Cintiq.There may be a problem with the Inkwell preferences. Remove the damaged preference files as follows. They will be recreated when you enable handwriting recognition.1. From the Apple menu, choose SYSTEM PREFERENCES. From the System Preferences menu, choose SHOW ALL and select INK. Then turn off handwriting recognition.2. From the GO menu, choose your HOME. Open the LIBRARY and PREFERENCES folders. Then remove the following preferences:• com.apple.ink.framework.plist• com.apple.ink.inkpad.plist• com.apple.ink.inkpad.sketch3. Go back to SYSTEM PREFERENCES and INK, and then enable handwriting recognition.4. Test the Inkwell function using your Wacom pen display tablet and pen.5. If this procedure does not resolve your problem with Inkwell, contact Apple Support for further assistance. Wacom is not the software manufacturer for Inkwell and we are limited in our abilities to support a third-party software application.DTZ-2000_Manual.fm Page 51 Wednesday, December 27, 2006 9:37 AM
TroubleshootingPage 52Technical support optionsIf you have a problem with your Cintiq pen display, first check the Installation section in this guide to make sure the unit is installed correctly. Then review the Troubleshooting procedures within this guide; your problem may be described there and you can try the solution(s) offered.If you cannot find the answer in this guide, you may find updated information about your problem in the appropriate Read Me file for your platform (located on the Wacom Pen Tablet Driver CD). You can also check the product FAQs (Frequently Asked Questions) on the Wacom web site for your region.If you have an Internet connection you can download the latest software drivers from the Wacom web site for your region. See Obtaining driver downloads on page 53.If you cannot solve the problem and you think your Wacom product is not working properly, contact the Wacom support staff for the area where your product was purchased. See the Wacom tablet Read Me file, located on the Wacom Pen Tablet Driver CD, for contact information.When you call, you should be at your computer with the following information available:• This manual.• Pen display tablet serial number. (Look at the label on the back of the unit. You may have to rotate the unit in order to see the serial number label.)• Driver version number. (See the Wacom Pen Tablet Driver CD or click on the Wacom Tablet control panel ABOUT button.)• The make and model of your computer, and operating system version number.• The make, model, and connection type of your video card.• A list of peripheral devices attached to your computer.• The software application and version you were using when the problem occurred.• The exact wording of any error message that appeared on your screen.• What happened and what you were doing when the problem occurred.• How you tried to solve the problem.DTZ-2000_Manual.fm Page 52 Wednesday, December 27, 2006 9:37 AM
Troubleshooting Page 53Obtaining driver downloadsWacom periodically updates the pen tablet software driver to maintain compatibility with new products. If you are having a compatibility problem between your Cintiq pen display and a new hardware or software product, it may be helpful to download a new Wacom tablet software driver (when available) from the Internet.USA, Canada, Central and South AmericaEurope, Middle East and AfricaJapanAsia Pacific (English)ChinaKoreaTaiwanWorldwide Web: http://www.wacom.com/productsupport Driver downloads.Worldwide Web: http://www.wacom.eu Software updates.Anonymous FTP Site: ftp://ftp.wacom.eu/pub/ Software updates. Worldwide Web: http://tablet.wacom.co.jp Software updates. (Japanese)Worldwide Web: http://www.wacom-asia.com Software updates. (English)Worldwide Web: http://www.wacom.com.cn Software updates. (Simplified Chinese)Worldwide Web: http://www.wacomdigital.co.kr Software updates. (Korean)Worldwide Web: http://www.wacom.com.tw Software updates. (Traditional Chinese)DTZ-2000_Manual.fm Page 53 Wednesday, December 27, 2006 9:37 AM
AppendixPage 54APPENDIXCaring for CintiqKeep the Grip Pen and your Cintiq LCD screen surface clean. Dust and dirt particles can stick to the pen and cause wear to the display screen surface. Regular cleaning will help to prolong the life of your LCD screen surface and pen. Keep Cintiq, the Cintiq stand, and the Grip Pen in a clean, dry place and avoid extremes in temperature. Room temperature is best. Cintiq, the Cintiq stand, and the Grip Pen are not made to come apart. Taking apart the product will void your warranty.Important: Take care to never spill liquids onto the pen display tablet or pen. Be especially careful of getting the display, tablet ExpressKeys, Touch Strips, or pen buttons, tip, and eraser wet – they contain sensitive electronic parts that will fail if liquids enter them.CleaningTo clean the Cintiq casing, the Cintiq display stand, or the Grip Pen, use a soft, damp cloth; you can also dampen the cloth using a very mild soap diluted with water. Do not use paint thinner, benzine, alcohol, or other solvents to clean the unit casing or pen.To clean the display screen, use an anti-static cloth or a slightly damp cloth. When cleaning, apply only a light amount of pressure to the display screen and do not make the surface wet. Do not use detergent to clean the display screen; this may damage the coating on the screen. Please note that damage of this kind is not covered by the manufacturer’s warranty.DTZ-2000_Manual.fm Page 54 Wednesday, December 27, 2006 9:37 AM
Appendix Page 55Replacing the pen tipThe pen tip (nib) will wear with normal use. Excessive pressure will cause the nib to wear sooner. When the nib gets too short or develops a sharp edge, replace it with one of the extra nibs that came with the pen.If the pen nib wears and becomes angular, it may damage the coating on the Cintiq display screen. To avoid this, periodic nib replacement is recommended.Important: When the pen is not in use, place it in the pen stand, the pen holder, or lay it flat on your desk. To maintain the sensitivity of your pen, do not store the tool in a container where it will rest on its tip or eraser.WARNING Prevent children from swallowing the pen tip or side switch. The pen tip (nib) or side switch may accidentally be pulled out if children are biting on them.To remove the old nib:Clasp it with a Wacom nib extractor, pair of tweezers, needle-nosed plier, or similar instrument and pull the old nib straight out of the pen.To insert a new nib:Slide it straight into the barrel of the pen. Firmly push the nib until it stops. The new nib will slide into the correct position.DTZ-2000_Manual.fm Page 55 Wednesday, December 27, 2006 9:37 AM
AppendixPage 56Optional display configurationsAfter mounting the pen display unit on the Cintiq stand, you can rotate the pen display tablet to a variety of positions. If you do not plan to rotate the Cintiq and want to fasten it more securely to the stand, you can install the rotation lock screws as shown below.To lock Cintiq to the display stand:• Rotate the pen display to the standard landscape position (with the power switch located at the top of the unit).• Line up the two holes in the stand with two screw holes on the Cintiq unit.• Insert the lock screws and hand-tighten them.CAUTION Avoid placing excess physical pressure on the Cintiq stand; doing so can damage the stand.Lock screwsDTZ-2000_Manual.fm Page 56 Wednesday, December 27, 2006 9:37 AM
Appendix Page 57Using an alternate mount or standCintiq can be attached to any mount arm or stand conforming to the VESA 100 standard.Mounting screws that are 4 mm wide with a 0.7 mm pitch (M4 Regular), with a screw clearance depth from 13 – 18 mm are required.To attach Cintiq to a VESA 100 mounting platform:1. Turn off your computer and power off Cintiq. Then disconnect all cables from between the unit and your computer.2. Remove Cintiq from its stand and place it face down on a flat, soft surface (such as a cloth spread across a desktop).3. Remove the bearing hub by unscrewing the four bearing hub attachment screws. Then carefully separate the bearing halves and remove the bearing stopper to free up the cabling. Take care not to lose the small bearing stopper found within the inner groove of one of the hub sections.Bearing hub sections (removed)Attachment screwsCable cover plate (removed)Attachment screwsCable channelBearing stopperDTZ-2000_Manual.fm Page 57 Wednesday, December 27, 2006 9:37 AM
AppendixPage 584. Next remove the four attachment screws from the cable cover plate and lift the plate away from the pen display unit.5. Place the cable into the cable exit channel. Then reattach the cable cover plate making sure to use the correct screws for reattachment. (The cable cover plate screws are shorter than the bearing hub attachment screws.)6. Using the screws that came with the bearing hub recess cover plate (included with your product), install the plate in place of the bearing hub to protect the interior of the unit from dust particles.7. Now, using the appropriate VESA mounting screws, firmly attach Cintiq to the alternate mounting platform.8. Refer to the Installation instructions beginning on page 15 and reattach the cabling to your computer.To remove Cintiq from an alternate mounting platform:1. Turn off your computer and power off Cintiq. Then disconnect all cables from between the unit and your computer.2. Remove Cintiq from the alternate mounting platform.3. Place the pen display unit face down on a flat, soft surface (such as a cloth spread across a desktop). Remove the bearing cover plate.4. Remove the cable cover plate and lift the cable out of the cable channel. After freeing up the cable, replace the cable cover plate.5. Lay out and study the bearing hub components – you should have two bearing hub sections, a bearing stopper, and four screws. Locate the bearing stopper within one of the bearing hub sections. (Either hub section can be used, as they are identical parts.) When correctly placed, the bearing stopper will shift smoothly from side to side within the stopper groove. The stopper will also sit flush with the rear hub surface.CAUTION When attaching Cintiq onto an alternate mounting platform, be sure to follow all instructions in the documentation supplied by the platform manufacturer. If improperly installed, the unit could fall, resulting in damage to the unit or physical injury.Illustrates correct location of bearing stopper within bearing hub section.DTZ-2000_Manual.fm Page 58 Wednesday, December 27, 2006 9:37 AM
Appendix Page 596. Taking care not to dislodge the bearing stopper from the hub section, position the two halves of the bearing hub together around the pen display tablet cable and over their attachment points.7. Attach the bearing hub sections to the unit making sure to use the correct screws for reattachment. (The bearing hub screws are longer than the cable cover plate screws.)Proper positioning shows the hub sections aligned along the horizontal axis of the pen display tablet.The section containing the bearing stopper should be positioned toward the top of the pen display tablet.DTZ-2000_Manual.fm Page 59 Wednesday, December 27, 2006 9:37 AM
AppendixPage 60Pen and digital ink capabilities in Windows VistaMicrosoft Windows Vista provides extensive support for pen and touch input. When using Cintiq with a computer running Windows Vista, your experience is enhanced by powerful note taking, handwriting recognition, fast navigation, and other digital inking options designed to give you quick, intuitive results with the Wacom pen.•Note taking. Use your Wacom pen to jot notes and capture quick sketches in Microsoft Journal. Journal simulates a physical notebook, but with the advantages of digital note taking – you can choose from a variety of pen, marker, and highlighter tools, plus an eraser that is easily activated by the eraser end of your Wacom pen. Journal also includes a powerful search engine that can even locate your handwritten content.•Handwriting recognition. Because Windows Vista includes powerful handwriting recognition capabilities, you can use your Wacom pen to quickly enter handwritten information anywhere the computer accepts typed input. You can convert your handwritten content to typed text at any time.•Gestures. Use your Wacom pen to make simple gestural movements on the tablet to trigger customizable actions for navigation, editing, and other functions. To customize your gestures, select the FLICKS tab in the PEN AND INPUT DEVICES control panel.•Digital Ink in Microsoft Office 2007. Use your Wacom pen to full advantage with the enhanced digital mark-up and inking tools available in Microsoft Office 2007 applications running on Windows Vista. Found on the REVIEW tab within applicable applications, these tools provide a consistent set of inking options. For quick access, you can add specific inking tools to the Quick Access Toolbar located at the top of each application.About the Windows Vista Tablet PC Input PanelThe Windows Vista Tablet PC Input Panel enables you to use handwriting or an on-screen keyboard to directly enter text with your Wacom pen. There are a number of ways to launch the Input Panel:• Click on the Input Panel icon which appears when you move the screen cursor into a text entry area.• Click on the Input Panel tab, located by default on the left edge of the display screen.• Click on the Tablet PC Input Panel icon located on the Windows taskbar. If the icon is not visible, right-click on the taskbar, select TOOLBARS, and TABLET PC INPUT PANEL.To customize the Input Panel:1. First open the Input Panel and then click on TOOLS in the menu bar.2. Select OPTIONS to open the Input Panel Options dialog box.3. Customize the Input Panel settings for the way you like to work.To learn more about using your Wacom pen in Microsoft Windows Vista and Office 2007, be sure to study the documentation that came with your system and Microsoft Office applications. Be sure to take advantage of the Windows Vista training tools, including the Tablet PC tutorial, available from Microsoft.You can visit also the Wacom web site at www.wacom.com/vista for additional information on working with your Wacom pen in Windows Vista.DTZ-2000_Manual.fm Page 60 Wednesday, December 27, 2006 9:37 AM
Appendix Page 61Uninstalling CintiqFollow the appropriate procedure below to remove the Wacom tablet software and Cintiq pen display from your system.Important: When you remove the Wacom tablet driver software from your system, any other Wacom tablet connected to your computer will no longer operate with full Wacom tablet functionality.Windows:1. Click on the Windows START button and open the CONTROL PANEL.2. In the CONTROL PANEL window for• Windows Vista: click on PROGRAMS AND FEATURES. In the dialog box that appears, choose the TABLET option and click on the UNINSTALL button.• Windows XP or XP x64: select ADD OR REMOVE PROGRAMS. In the ADD OR REMOVE PROGRAMS window, choose TABLET and click on the REMOVE button.• Windows 2000: double-click on the ADD/REMOVE PROGRAMS icon. In the dialog box that appears, choose the TABLET option and click on the ADD/REMOVE... button.3. Follow the prompts to remove the tablet driver. (If prompted, enter your administrator login name and password.)4. When the driver has been removed, shut down your system, power off your computer, and turn off Cintiq. When your computer and Cintiq are off, disconnect Cintiq from your computer.Macintosh: 1. From the GO menu, choose APPLICATIONS and open the TABLET folder.2. Double-click on the REMOVE TABLET icon and select the REMOVE TABLET SOFTWARE button. Enter your administrator login name and password.3. After the removal is completed, click OK.4. Shut down your computer and turn off Cintiq. When your computer and Cintiq are off, disconnect Cintiq from your computer.DTZ-2000_Manual.fm Page 61 Wednesday, December 27, 2006 9:37 AM
AppendixPage 62Product specificationsGeneral specificationsLCD monitorPhysical dimensions (W x D x H) 547 x 367 x 46 mm (21.55 x 14.46 x 1.81 in), excluding standWeight 7.4 kg (16.3 lb), excluding stand9.1 kg (20.0 lb), including standInput voltage 12 VDCPower consumption 50 W or less (12 VDC) in normal operation mode2 W or less (12 VDC) in suspend or standby modes1 W or less in off modeOperating temperature and humidity 5° to 35° C, 20 to 80% RH (non-condensing)Storage temperature and humidity -10° to 60° C, 20 to 90% RH (non-condensing)(maximum storage humidity is 38% at a temperature of 60° C, and maximum storage temperature is 42° C at a humidity of 90%)Certification and compliance FCC part 15 class B, CE, VCCI Class B, EDID 1.3, C-tick, MIC, BSMI, CCC, RoHS, GOST-RDisplay a-Si TFT active matrix LCDScreen size 20.1 in diagonal, 433.4 x 270.9 mm (17.1 x 10.7 in)Aspect ratio 16 : 10Resolution 1680 x 1050 (WSXGA), 1280 x 1024 pixels (SXGA), 1024 x 768 pixels (XGA), 800 x 600 pixels (SGA), 640 x 480 pixels (VGA), othersSynchronization range 60 Hz vertical (for WSXGA)50 to 75 Hz vertical, 30 to 82 kHz horizontal (for resolutions less than WSXGA)Pixel pitch 0.258 x 0.258 mm (0.10 x 0.10 in)Color depth 16.77 million colors (24 bit)Pixels 1,764,000Response time (refresh rate) 16 ms (rise and fall)Brightness 250 / 300 cd/m2 (typical)Contrast ratio 600:1Plug and Play DDC2B and other DVI standardsLCD quality Each Cintiq LCD panel is produced under very stringent quality standards. Production techniques cannot guarantee an absolutely perfect TFT display. Wacom does not allow any pixel to be always white or always black. The Cintiq DTZ-2000 display contains 5.29 million sub-pixels (red, green, or blue dots). A small number of sub-pixels (5 or less) can be partially on or partially off – this does not mean the display is defective. In a partially on sub-pixel, 50% or more of the sub-pixel is always lit. In a partially off sub-pixel, 50% or more of the sub-pixel is always dark.DTZ-2000_Manual.fm Page 62 Wednesday, December 27, 2006 9:37 AM
Appendix Page 63Pen tabletDisplay standPower adapterGrip pen (model ZP-501E)Reading technology Electromagnetic resonance technologyActive area 433.4 x 270.9 mm (17.0 x 10.7 in)Resolution 0.005 mm/point (5080 lpi)Accuracy ±0.5 mm (±0.02 in), averageTilt range (all pens) ±60 degreesReading height 5 mm (0.2 in)Maximum report rate 136 points/sec.ExpressKeys stroke 1 mm (0.04 in), approximatelyTouch Strips 52 mm (2.0 in) x 12 mm (0.47 in)Pressure levels 1024 levelsCommunication interface USB*Patented Patent no. 6,874,744Physical dimensions (W x D x H) 329 x 299 x 165 mm (13.0 x 11.8 x 6.5 in)Weight 1.7 kg (3.7 lb)Rotation ±180°Incline 10° to 65° from horizontalPrimary orientation Landscape, lockableInput voltage 100 to 240 VAC, 50/60 HzOutput voltage 12 VDC, 5.83 APressure sensitivity 1024 levels (tip and eraser)Eraser tip travel 1.3 mm (0.05 in), approximatelyPhysical size (L x D) 175.0 x 15.0 mm (6.89 x 0.59 in)Weight 18 g (0.63 oz), approximatelyTip refill typesThe Grip Pen comes equipped with three standard nibs (white) for general multi-purpose use, a spring-loaded stroke nib (gray) providing a brush-like feeling to your work, and a felt nib (black) that has a higher friction than the standard nib.Standard nib, polyacetal (part no. PSI-A007, qty 5)Stroke nib (part no. PSI-A042, qty 5)Felt nib (part no. PSI-A043, qty 5)DTZ-2000_Manual.fm Page 63 Wednesday, December 27, 2006 9:37 AM
AppendixPage 64AccessoriesAirbrush. A true digital airbrush incorporating a pressure-sensitive tip and eraser, tilt sensitivity, and a fingerwheel that provides an additional degree of control over the application of digital paint. This tool also includes a programmable side switch. ZP-400E6D Art Pen. This pen provides rotation sensing technology with a unique chisel-shaped nib that emulates brushes, markers, and calligraphic pens. Simply by rotating the pen, a drawn line becomes narrow or broad. When the 6D Art Pen is combined with a software application supporting its feature set, the pen can produce almost any type of brush effect or marker stroke.ZP-600Classic Pen. This pressure-sensitive pen has the same feature set as the Cintiq Grip Pen, but with a slimmer profile that does not include a rubberized grip. ZP-300EReplacement nibsStandard nibs, polyacetal, (white) for Grip Pen (model ZP-501E), Airbrush (model ZP-400E), or Classic Pen (model ZP-300E)PSI-A007, qty 5Stroke nib (gray) for Grip Pen, Airbrush, or Classic Pen. Stroke nibs are spring-loaded, providing additional tactile feedback when you are working with the Grip Pen or Airbrush. They are installed in the same manner as a standard pen nib.PSI-A042, qty 5Felt nib, for Grip Pen (model ZP-501E), Airbrush (model ZP-400E), or Classic Pen (model ZP-300E)PSI-A043, qty 5Standard nib, for Art Pen (model ZP-600) PSI-A052, qty 5Felt nibs, for Art Pen (model ZP-600) PSI-A051, qty 5Pen stand, for Grip Pen and Art Pen PST-A034Pen tether FUZ-A108DTZ-2000_Manual.fm Page 64 Wednesday, December 27, 2006 9:37 AM
Appendix Page 65Display adaptersPurchasing parts and accessoriesTo purchase parts and accessories, refer to the Cintiq Read Me file and see who to call for your region.You can also do the following:•To purchase parts and accessories in the USA or Canada, call 1.888.884.1870 (toll-free) or visit Wacom’s web site at http://www.wacomdirect.com (USA only).•To purchase parts and accessories in Europe, call +49 (0)180.500.03.75 or send an email to spareparts@wacom.eu. Or, visit the Wacom web site at www.wacom.eu/solutionstore. You can also contact your local dealer, distributor, or Technical Support using the appropriate number for your region.•To purchase parts and accessories in other countries, please contact your local dealer or distributor.Please note that not all parts and accessories may be available in all regions.VGA to DVI-I adapter Part number STJ-A252Video card connection: VGA (RGB analog, male)Display connection: DVI-I, femaleDVI-D to DVI-I adapter Part number STJ-A253Video card connection: DVI-D, maleDisplay connection: DVI-I, femaleDTZ-2000_Manual.fm Page 65 Wednesday, December 27, 2006 9:37 AM
AppendixPage 66Radio and television interferenceThe equipment described in this manual generates, uses, and can radiate radio-frequency energy. If it is not installed and used properly – that is, in strict accordance with Wacom instructions – it may cause interference with radio and television reception.Federal Communications Commission (FCC) noticeThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.You can determine whether the equipment is causing interference by powering it off. If the interference stops, it was probably caused by the equipment.If the equipment does cause interference to radio or television reception, you may be able to correct the interference by using one or more of the following measures:• Rotate the television or radio antenna until the interference stops.• Move the equipment farther away from the television or radio.• Plug the equipment and computer into an outlet that is on a different circuit from the television or radio.If necessary, consult your Wacom dealer or an experienced radio/television technician for help.Changes or modifications to this product not authorized by Wacom could void the FCC Certification and negate your authority to operate the product.CE declarationThe Cintiq DTZ-2000 pen display has been tested and found to comply with the following harmonized European Norms:• EN 55024: 1998+A1:2001+A2:2003 (electromagnetic immunity)• EN 55022: 1998+A1:2000+A2:2003, Class B (electromagnetic emissions)• EN 61000-3-2: 2000, Class D (electromagnetic emissions)• EN 61000-3-3: 1995+A1:2001 (electromagnetic emissions)The Wacom power adapters have been tested by their manufacturers and found to comply with the following harmonized European Norms:• EN 55024: 1998+A1:2001 (electromagnetic immunity)• EN 55022: 1998+A1:2000, Class B (electromagnetic emissions)• EN 61000-3-2: 2000, Class D (electromagnetic emissions)• EN 61000-3-3: 1995+A1: 2001 (electromagnetic emissions)• EN 60950: 2000 (safety)Based on the results of these tests, Wacom declares that the above mentioned device conforms to the European Council Directive 89/336/EEC, and their amendment Directive 93/68/EEC and indicates this conformity by the CE-sign on each device.The device must be installed and operated always in strict accordance with the instructions given in this manual. Any changes or modifications to this product that were not specifically authorized by Wacom will invalidate this declaration.DTZ-2000_Manual.fm Page 66 Wednesday, December 27, 2006 9:37 AM
Appendix Page 67Warranty(Worldwide, Except for Europe, Africa and Middle East)Limited WarrantyWacom warrants the product, to the original consumer purchaser, except for the Software and consumable items such as the pen nibs, to be free from defects in materials and workmanship under normal use and service for a period of two (2) years, from the date of original retail purchase, as evidenced by a copy of the receipt and registration with Wacom by mail or online within 30 days of purchase.The Software is licensed “as is.” Wacom makes no warranty with respect to its quality or performance. Wacom cannot guarantee you uninterrupted service or the correction of any errors.Upon discovery of a defect in the product, except in the Software, within the Warranty Period, you should contact Wacom Technical Support via telephone, email, or fax to obtain an RMA (Return Merchandise Authorization) number and instructions for shipping the product to a service location designated by Wacom. You should send the product, shipping charges prepaid, to the designated service location, accompanied by the return authorization number, your name, address and telephone number, proof of purchase date, and a description of the defect. Wacom will pay for return shipping by United Parcel Service or by an equivalent service as chosen by Wacom.Wacom’s sole obligation and entire liability under this warranty shall be, at Wacom’s option, either the repair or replacement of the defective product or parts thereof of which Wacom is notified during the Warranty Period; provided, however, that you are responsible for (i) the cost of transportation of the product to the designated service location and (ii) any loss or damage to the product resulting from such transportation.Wacom shall have no responsibility to repair or replace the product if the failure of the product has resulted from accident, abuse, misuse, negligence, or unauthorized modification or repair, or if it has been handled or stored other than in accordance with Wacom’s storage instructions.Any descriptions, drawings, specifications, samples, models, bulletins, or similar material, used in connection with the sale of the product, shall not be construed as an express warranty that the product will conform or comply with your requirements.EXCEPT FOR THE LIMITED WARRANTY DESCRIBED ABOVE, THERE ARE NO OTHER WARRANTIES MADE BY WACOM ON THIS PRODUCT. NO ORAL OR WRITTEN INFORMATION OR ADVICE GIVEN BY WACOM, ITS DEALERS, DISTRIBUTORS, AGENTS, OR EMPLOYEES SHALL CREATE A WARRANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY, AND YOU MAY NOT RELY ON ANY SUCH INFORMATION OR ADVICE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.WACOM LIMITS THE DURATION OF ANY LEGALLY IMPLIED WARRANTIES INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, TO THE DURATION OF WACOM’S EXPRESS WARRANTY. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.NEITHER WACOM NOR ANYONE ELSE WHO HAS BEEN INVOLVED IN THE CREATION, PRODUCTION, OR DELIVERY OF THIS PRODUCT SHALL BE LIABLE FOR ANY DIRECT, CONSEQUENTIAL, OR INCIDENTAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION AND THE LIKE) ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH PRODUCT, EVEN IF WACOM HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.In the event that any of the above limitations are held unenforceable, Wacom’s liability for any damages to you or any party shall not exceed the purchase price you paid, regardless of the form of any claim. This Limited Warranty is governed by the laws of the United States of America and the state of Washington.This Limited Warranty is valid for and only applies to products purchased and used inside the United States (and its territories or possessions) and Canada.DTZ-2000_Manual.fm Page 67 Wednesday, December 27, 2006 9:37 AM
AppendixPage 68Warranty Service in the U.S.A. and CanadaTo obtain Warranty service within the U.S. or Canada contact:Wacom Technical SupportPhone: 1.360.896.9833Fax: 1.360.896.9724Inquiry Form: http://www.wacom.com/productsupport/email.cfmE-mail: support@wacom.comWarranty Service Outside of the U.S.A. and CanadaFor products purchased or used outside of the United States and Canada, the warranty period is one (1) year from the date of original retail purchase. Upon discovery of a defect in the product, except in the Software, within the Warranty Period you should contact your local dealer or distributor. If an authorized Wacom repair center is not available in your local country you will be responsible for all transportation costs including duties and taxes to and from the Wacom repair center. In all other respects the terms of the warranty as set forth above apply to such sales.Should you have any questions about this Agreement, or if you desire to contact Wacom for any reason, please contact in writing:<<<TBD - Do we add contact info for Japan, Asia Pacific, and Mainland China (as we do for Graphire?&&&>>>In North and South America contact:Wacom Technology Corporation1311 SE Cardinal CourtVancouver, Washington 98683U.S.A.DTZ-2000_Manual.fm Page 68 Wednesday, December 27, 2006 9:37 AM
Wacom Technology Corporation Wacom Europe GmbH1311 SE Cardinal Court Europark Fichtenhain A9Vancouver, WA 98683 47807 KrefeldU.S.A. GermanyTelephone TelephoneGeneral: +1.360.896.9833 General: +49.(0)2151.3614.0Fax: +1.360.896.9724 Fax: +49.(0)2151.3614.111Wacom Co., Ltd. Wacom Co., Ltd.2-510-1 Toyonodai Asia Pacific OfficeOtone-Machi, Kitasaitama-Gun Harmony Tower 18F, 1-32-2 Hon-Cho,Saitama, 349-1148 Nakano-Ku, Tokyo 164-0012Japan JapanInternet: http://tablet.wacom.co.jp TelephoneGeneral: +81.3.5309.1513Fax: +81.3.5309.1514Wacom China Corporation Wacom Digital Solutions Co., Ltd.1108 Block One, Kuntai International Bldg, Gangnam Telepia B/D 9th Fl, 662-1812 Chao Wai Street, Chao Yang District Yeoksam-dong, Gangnam-gu, Seoul, 135-080Beijing, China 100020 KoreaTelephone TelephoneGeneral: +86.10.5879.0880 General: +82.2.557.3894Fax: +86.10.5879.0102 Fax: +82.2.557.3895Wacom Australia Pty. Ltd. Wacom Singapore Pte. Ltd. (Singapore)Level 5, 18 Orion Rd, 3 Bishan Place,Lane Cove West NSW 2066, Australia CPF Bishan Building #06-08Singapore 579838Telephone TelephoneGeneral: +61.2.9422.6700 General: +65.6258.8640Fax: +61.2.9420.2272 Fax: +65.6258.8697DTZ-2000_Manual.fm Page 69 Wednesday, December 27, 2006 9:37 AM
Installation Guide & Hardware ManualWacom Co., Ltd. UE-0364DTZ-2000_Manual.fm Page 70 Wednesday, December 27, 2006 9:37 AM
This device complies with Part 15 of the FCC rules, operation is subject to the following two conditions. （1）This device may not cause harmful interference and, （2）This device must accept any interference received, including interference that may cause undesired operation . NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT

Navigation menu