Wasp Bar Code Duraline Wls 8400 Er Users Manual NGIS
WLS 8400 ER to the manual ec7eea4b-6d98-4347-8ade-6748fdab9070
2015-02-02
: Wasp-Bar-Code Wasp-Bar-Code-Wasp-Duraline-Wls-8400-Er-Users-Manual-454193 wasp-bar-code-wasp-duraline-wls-8400-er-users-manual-454193 wasp-bar-code pdf
Open the PDF directly: View PDF .
Page Count: 394
Download | |
Open PDF In Browser | View PDF |
WLS 8400 Product Reference Guide February 2005 © 2005 by Wasp Technologies. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Wasp Technologies. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a licensed basis. Wasp Technologies grants to the user a non-transferable and nonexclusive license to use each software or firmware program delivered hereunder (licensed program). Except as noted below, such license may not be assigned, sublicensed, or otherwise transferred by the user without prior written consent of Wasp Technologies. No right to copy a licensed program in whole or in part is granted, except as permitted under copyright law. The user shall not modify, merge, or incorporate any form or portion of a licensed program with other program material, create a derivative work from a licensed program, or use a licensed program in a network without written permission from Wasp Technologies. The user agrees to maintain Wasp Technologies’s copyright notice on the licensed programs delivered hereunder and to include the same on any authorized copies it makes, in whole or in part. The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed program delivered to the user or any portion thereof. Wasp Technologies reserves the right to make changes to any software or product to improve reliability, function, or design. Wasp Technologies does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any Wasp Technologies, intellectual property rights. An implied license only exists for equipment, circuits, and subsystems contained in Wasp Technologies products. Wasp Technologies is a registered trademark of Wasp Technologies. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. Wasp Technologies 1400 10th St. Plano TX 75074 http://www.waspbarcode.com 2 Contents About This Guide Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv Chapter Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv Notational Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xvi Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xvi Service Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xvi Wasp Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xvii Chapter 1. Getting Started Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unpacking the Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting Up the Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing the Interface Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting Power (if required) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing the Interface Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring the Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 1-4 1-5 1-5 1-6 1-7 1-7 iv WLS 8400 Product Reference Guide Chapter 2. Scanning Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Beeper Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 LED Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Scanning in Hand-Held Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Aiming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 Scanning in Hands-Free Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 Decode Zone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 Chapter 3. Maintenance and Technical Specifications Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 Scanner Signal Descriptions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 Chapter 4. User Preferences Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Scanning Sequence Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Errors While Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 User Preferences Default Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 User Preferences. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Set Default Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Beeper Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Beeper Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Power Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Laser On Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Beep After Good Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Trigger Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Aim Duration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Contents v Chapter 5. Keyboard Wedge Interface Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Connecting a Keyboard Wedge Interface . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 Keyboard Wedge Default Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Keyboard Wedge Host Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 Keyboard Wedge Host Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 Keyboard Wedge Country Types (Country Codes) . . . . . . . . . . . . . . 5-8 Ignore Unknown Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10 Keystroke Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10 Intra-Keystroke Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11 Alternate Numeric Keypad Emulation . . . . . . . . . . . . . . . . . . . . . . . 5-12 Caps Lock On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12 Caps Lock Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13 Convert Wedge Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14 Function Key Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14 FN1 Substitution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15 Send Make and Break. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15 Keyboard Maps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-16 ASCII Character Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19 Chapter 6. RS-232 Interface Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Connecting an RS-232 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 RS-232 Default Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5 RS-232 Host Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6 RS-232 Host Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9 Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10 Parity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12 Check Receive Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13 Stop Bit Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14 Data Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14 Hardware Handshaking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15 Software Handshaking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-18 Host Serial Response Time-out . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20 vi WLS 8400 Product Reference Guide RTS Line State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-21 Beep on. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22 Intercharacter Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-23 Nixdorf Mode A/B and OPOS/JPOS Beep/LED Options . . . . . . . . 6-24 Ignore Unknown Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25 ASCII / Character Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-26 Chapter 7. USB Interface Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Connecting a USB Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 USB Default Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6 USB Host Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7 USB Device Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7 USB Country Keyboard Types (Country Codes) . . . . . . . . . . . . . . . . 7-8 USB Keystroke Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10 USB CAPS Lock Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11 USB Ignore Unknown Characters. . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12 Emulate Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13 USB Keyboard FN 1 Substitution. . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14 Function Key Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14 Simulated Caps Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15 Convert Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15 ASCII Character Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-16 Chapter 8. Symbologies Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Scanning Sequence Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Errors While Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Symbology Default Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6 UPC/EAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Enable/Disable UPC-A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Enable/Disable UPC-E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Enable/Disable UPC-E1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11 Enable/Disable EAN-13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11 Contents vii Enable/Disable EAN-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12 Enable/Disable Bookland EAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-12 Decode UPC/EAN/JAN Supplementals . . . . . . . . . . . . . . . . . . . . . . 8-13 UPC/EAN/JAN Supplemental Redundancy. . . . . . . . . . . . . . . . . . . 8-15 Transmit UPC-A/UPC-E/UPC-E1 Check Digit . . . . . . . . . . . . . . . . 8-15 UPC-A Preamble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-17 UPC-E Preamble. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18 UPC-E1 Preamble. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19 Convert UPC-E to UPC-A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20 Convert UPC-E1 to UPC-A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21 EAN-8/JAN-8 Extend. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-22 Code 128 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-22 Enable/Disable Code 128 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-22 Enable/Disable UCC/EAN-128 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23 Enable/Disable ISBT 128 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23 Code 39 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-24 Enable/Disable Code 39 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-24 Enable/Disable Trioptic Code 39 . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-24 Convert Code 39 to Code 32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-25 Code 32 Prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-26 Set Lengths for Code 39 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-27 Code 39 Check Digit Verification . . . . . . . . . . . . . . . . . . . . . . . . . . 8-29 Transmit Code 39 Check Digit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-30 Code 39 Full ASCII Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-31 Code 93 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-32 Enable/Disable Code 93 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-32 Set Lengths for Code 93 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-32 Code 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-34 Code 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-34 Set Lengths for Code 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-34 Code 11 Check Digit Verification . . . . . . . . . . . . . . . . . . . . . . . . . . 8-36 Transmit Code 11 Check Digits . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-37 Interleaved 2 of 5 (I 2 of 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-38 Enable/Disable Interleaved 2 of 5. . . . . . . . . . . . . . . . . . . . . . . . . . . 8-38 Set Lengths for Interleaved 2 of 5 . . . . . . . . . . . . . . . . . . . . . . . . . . 8-38 I 2 of 5 Check Digit Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-41 viii WLS 8400 Product Reference Guide Transmit I 2 of 5 Check Digit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-42 Convert I 2 of 5 to EAN-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-42 Discrete 2 of 5 (D 2 of 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-44 Enable/Disable Discrete 2 of 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-44 Set Lengths for Discrete 2 of 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-44 Codabar (NW - 7). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-46 Enable/Disable Codabar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-46 Set Lengths for Codabar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-47 CLSI Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-49 NOTIS Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-49 MSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-50 Enable/Disable MSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-50 Set Lengths for MSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-50 MSI Check Digits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-52 Transmit MSI Check Digit(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-53 MSI Check Digit Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-53 RSS (Reduced Space Symbology) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-54 RSS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-54 RSS Limited . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-54 Convert RSS to UPC/EAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-55 Redundancy Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-56 Redundancy Level 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-56 Redundancy Level 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-56 Redundancy Level 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-57 Redundancy Level 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-57 Security Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-58 Security Level 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-58 Security Level 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-58 Security Level 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-59 Security Level 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-59 Bi-Directional Redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-60 Chapter 9. Miscellaneous Scanner Options Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 Scanning Sequence Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4 Errors While Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4 Contents ix Miscellaneous Default Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4 Miscellaneous Scanner Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5 Transmit Code ID Character. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5 Scan Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6 Prefix/Suffix Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6 Scan Data Transmission Format. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7 FN1 Substitution Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9 Transmit “No Read” Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9 Chapter 10. Advanced Data Formatting Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 Rules: Criteria Linked to Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 Using ADF Bar Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 ADF Bar Code Menu Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4 Rule 1: The Code 128 Scanning Rule . . . . . . . . . . . . . . . . . . . . . . . 10-5 Rule 2: The UPC Scanning Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5 Alternate Rule Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5 Rules Hierarchy (in Bar Codes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7 Default Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-8 Special Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9 Pause Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9 Begin New Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9 Save Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9 Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10 Quit Entering Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10 Disable Rule Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11 Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12 Code Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12 Code Lengths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-17 Message Containing A Specific Data String . . . . . . . . . . . . . . . . . 10-23 Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-28 Send Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-28 Setup Field(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-32 Modify Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-39 Pad Data with Spaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-41 x WLS 8400 Product Reference Guide Pad Data with Zeros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-47 Beeps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-53 Send Keystroke (Control Characters and Keyboard Characters) . . 10-54 Send Right Control Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-97 Send Graphic User Interface (GUI) Characters . . . . . . . . . . . . . . . 10-97 Turn On/Off Rule Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-105 Alphanumeric Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-107 Appendix A. Standard Default Parameters Appendix B. Programming Reference Symbol Code Identifiers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 AIM Code Identifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4 Appendix C. Sample Bar Codes UPC-A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UPC-E. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . UPC-E1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EAN-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EAN-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Code 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Trioptic Code 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Code 93. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Code 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Codabar. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interleaved 2 of 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3 C-3 C-3 C-4 C-4 C-4 C-5 C-5 C-5 C-6 C-6 C-6 Contents xi Appendix D. Numeric Bar Codes 0, 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-3 2, 3, 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D-4 5, 6, 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D-5 8, 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D-6 Cancel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .D-7 Glossary Index xii WLS 8400 Product Reference Guide About This Guide Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv Chapter Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv Notational Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi Service Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii WASP Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii xiv WLS 8400 Product Reference Guide xv Introduction The WLS 8400 Product Reference Guide provides general instructions for setting up, operating, maintaining, and troubleshooting the scanner. The WLS 8400 includes the following variations of the scanner: • • WLS8400FZ: 1-D scanning WLS8400ER: extended range 1-D scanning. Chapter Descriptions • • • • • • • • • • • • • Chapter 1, Getting Started provides a product overview and unpacking instructions. Chapter 2, Scanning describes parts of the scanner, beeper and LED definitions, and how to use the scanner in hand-held and hands-free modes. Chapter 3, Maintenance and Technical Specifications provides information on how to care for the scanner, troubleshooting, and technical specifications. Chapter 4, User Preferences provides the programming bar codes necessary for selecting user preference features for the scanner. Chapter 5, Keyboard Wedge Interface provides information for setting up the scanner for Keyboard Wedge operation. Chapter 6, RS-232 Interface provides information for setting up the scanner for RS-232 operation. Chapter 7, USB Interface provides information for setting up the scanner for USB operation. Chapter 8, Symbologies describes all symbology features and provides the programming bar codes necessary for selecting these features for the scanner. Chapter 9, Miscellaneous Scanner Options includes commonly used bar codes to customize how the data is transmitted to the host device. Chapter 10, Advanced Data Formatting (ADF) describes how to customize scanned data before transmitting to the host. Appendix A, Standard Default Parameters provides a table of all host devices and miscellaneous scanner defaults. Appendix B, Programming Reference provides a table of AIM code identifiers, ASCII character conversions, and keyboard maps. Appendix C, Sample Bar Codes includes sample bar codes. xvi WLS 8400 Product Reference Guide • Appendix D, Numeric Bar Codes includes the numeric bar codes to scan for parameters requiring specific numeric values. Notational Conventions The following conventions are used in this document: • • • Bullets (•) indicate: • action items • lists of alternatives • lists of required steps that are not necessarily sequential. Sequential lists (e.g., those that describe step-by-step procedures) appear as numbered lists. Throughout the programming bar code menus, asterisks (*) are used to denote default parameter settings. * Indicates Default *Baud Rate 9600 Feature/Option Related Publications The WLS 8400 Quick Start Guide provides general information to help the user get started with the scanner. It includes basic set-up and operation instructions. For the latest versions of the WLS 8400 Quick Start Guide and the WLS 8400 Product Reference Guide go to: http://www.waspbarcode.com. Service Information If there is a problem with the equipment, contact the local Wasp Support. See page xvii for contact information. Before calling, have the model number, serial number, and several of the bar code symbols at hand. Call Wasp Support from a phone near the scanning equipment so that the service person can try to talk through the problem. If the equipment is found to be working properly and the problem is symbol readability, Wasp Support will request samples of the bar codes for analysis at our plant. xvii If the problem cannot be solved over the phone, the equipment may need to be returned for servicing. If that is necessary, specific directions will be given. Wasp Technologies is not responsible for any damages incurred during shipment if the approved shipping container is not used. Shipping the units improperly can possibly void the warranty. If the original shipping container was not kept, contact Wasp Technologies to request another container. Wasp Support For service information, warranty information or technical assistance contact or call Wasp Support at: 1400 10th Street Plano, TX 75074 214-547-4100 xviii WLS 8400 Product Reference Guide 1 Getting Started Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Unpacking the Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Setting Up the Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Installing the Interface Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Connecting Power (if required) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 Removing the Interface Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 Configuring the Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7 1-2 WLS 8400 Product Reference Guide Getting Started Introduction The scanner combines excellent scanning performance and advanced ergonomics to provide the best value in a lightweight laser scanner. Whether used as a hand-held scanner or in hands-free mode in a stand, the scanner ensures comfort and ease of use for extended periods of time. Figure 1-1. WLS 8400 Scanner This scanner supports: • • Standard RS-232 connection to a host. Keyboard Wedge connection to a host, where scanned data is interpreted keystrokes. The following international keyboards are supported (for WindowsTM environment): North America, German, French, French Canadian, Spanish, Italian, Swedish, UK English, Japanese, and Brazilian-Portuguese. 1-3 1-4 WLS 8400 Product Reference Guide • USB connection to a host. The scanner autodetects a USB host and defaults to the HID keyboard interface type. Other USB interface types may be selected by scanning programming bar codes. The following international keyboards are supported (for Windows™ environment): North America, German, French, French Canadian, Spanish, Italian, Swedish, UK English, Japanese, and BrazilianPortuguese. Unpacking the Scanner Remove the scanner from its packing and inspect it for damage. If the scanner was damaged in transit, call Wasp Support at one of the telephone numbers listed on page xvii. KEEP THE PACKING. It is the approved shipping container and should be used if the equipment ever needs to be returned for servicing. Getting Started Setting Up the Scanner Installing the Interface Cable 1. Loosen the two screws on the cable clamp at the bottom of the scanner and gently pull the clamp away from the bottom of the scanner. 2. Open the clamp and plug the interface cable modular connector into the cable interface port on the bottom of the scanner handle. 3. Gently tug the cable to ensure the connector is properly secured. 1-5 1-6 WLS 8400 Product Reference Guide 4. Close the clamp, push it back into place and tighten the screws on the clamp to secure the cable into the bottom of the scanner. 5. Connect the other end of the interface cable to the host (see the specific host chapter for information on host connections). Different cables are required for different hosts. The connectors illustrated in each host chapter are examples only. The connectors may be different than those illustrated, but the steps to connect the scanner remain the same. Connecting Power (if required) If the host does not provide power to the scanner, an external power connection is required to power the scanner. To connect power: 1. Connect the interface cable to the bottom of the scanner, as described in Installing the Interface Cable on page 1-5. 2. Connect the other end of the interface cable to the host (refer to the host manual to locate the correct port). 3. Plug the power supply into the power jack on the interface cable. Plug the other end of the power supply into an AC outlet. Getting Started Removing the Interface Cable 1. Loosen the two screws on the cable clamp at the bottom of the scanner and gently pull the clamp away from the bottom of the scanner. 2. Open the clamp and unplug the interface cable modular connector from the cable interface port on the bottom of the scanner handle. Carefully slide out the cable. 3. Follow the steps for Installing the Interface Cable on page 1-5 to connect a new cable. Configuring the Scanner Use the bar codes included in this manual to configure the scanner. See Chapter 4, User Preferences and each host chapter for information about programming the scanner using bar code menus. 1-7 1-8 WLS 8400 Product Reference Guide 2 Scanning Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Beeper Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 LED Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Scanning in Hand-Held Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6 Aiming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 Scanning in Hands-Free Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 Decode Zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 2-2 WLS 8400 Product Reference Guide Scanning Introduction This chapter provides beeper and LED definitions, techniques involved in scanning bar codes, general instructions and tips about scanning, and decode zone diagrams. Scan Tether Plate LED Indicators Scan Trigger Figure 2-1. Parts 2-3 2-4 WLS 8400 Product Reference Guide Beeper Definitions The scanner emits different beeper sequences and patterns to indicate its status. Table 2-1 defines beep sequences that occur during both normal scanning and while programming the scanner. Table 2-1. Standard Beeper Definitions Beeper Sequence Indication Standard Use Short low/short medium/short high beep sequence Power up. 1 short high beep A bar code symbol was decoded (if decode beeper is enabled). 4 long low beeps A transmission error was detected in a scanned symbol. The data is ignored. 5 long low beeps Conversion or format error. Short high/short high/short high/long low beep sequence RS-232 receive error. Parameter Menu Scanning Long low/long high beep sequence Incorrect programming sequence or ‘Cancel’ bar code scanned. Scanner remains in program mode. Short high/short low beep sequence Keyboard parameter selected. Enter value using bar code keypad. Short high/short low/short high/short low beep sequence Successful program exit with change in the parameter setting. Short low/short high/short low/short high beep sequence Out of host parameter storage space. Scan Set Default Parameter on page 4-5. USB only 4 short high beeps Scanner has not completed initialization. Wait several seconds and scan again. Short low/short medium/short high beep sequence after scanning a USB Device Type. Communication with the bus must be established before the scanner can operate at the highest power level. Short low/short medium/short high The USB bus may put the scanner in a state where power to the beep sequence occurs more than once. scanner is cycled on and off more than once. This is normal and usually happens when the PC cold boots. Scanning Table 2-1. Standard Beeper Definitions (Continued) Beeper Sequence Indication RS-232 only 1 short high beep A character is received and Beep on is enabled. LED Definitions In addition to beeper sequences, the scanner uses the two-color LED to indicate its status. Table 2-2 defines LED colors that display during scanning. Table 2-2. Standard LED Definitions LED Indication Off The scanner is on and ready to scan, or no power is applied to the scanner. Green A bar code was successfully decoded. Red A data transmission error occurred. 2-5 2-6 WLS 8400 Product Reference Guide Scanning in Hand-Held Mode Install and program the scanner (see Setting Up the Scanner on page 1-5). For assistance, contact the local supplier or Wasp Support. 1. Ensure the scanner is properly connected to the host (see the appropriate host chapter). 2. Aim the scanner at the bar code. 3. Press the scan trigger. Figure 2-2. Scanning in Hand-Held Mode 4. Ensure the scan line crosses every bar and space of the symbol. RIGHT WRONG 012345 012345 5. Upon successful decode, the scanner beeps, and the LED turns green. For more information on beeper and LED definitions, see Table 2-1 and Table 2-2. Scanning Aiming Do not hold the scanner directly over the bar code. Laser light reflecting directly back into the scanner from the bar code is known as specular reflection. This specular reflection can make decoding difficult. The scanner can be tilted up to 65° forward or back and achieve a successful decode (Figure 2-3). Simple practice quickly shows what tolerances to work within. 65° 65° Figure 2-3. Optimum Scan Angles 2-7 2-8 WLS 8400 Product Reference Guide Scanning in Hands-Free Mode The optional IntelliStand adds greater flexibility to the scanning operation. When the scanner is seated in the stand’s “cup,” the scanner’s built-in sensor places the scanner in hands-free mode. When the scanner is removed from the stand it operates in its normal hand-held mode. Adjust angle of scanner “cup” Scanner “Cup” Adjust height of IntelliStand Figure 2-4. Inserting the Scanner in the IntelliStand To operate the scanner in the IntelliStand: 1. Ensure the scanner is properly connected to the host (see the appropriate host chapter for information on host connections). 2. Insert the scanner into the IntelliStand by placing the front of the scanner into the stand’s “cup” (see Figure 2-4). 3. To scan a bar code, present the bar code and ensure the scan line crosses every bar and space of the symbol. 4. Upon successful decode, the scanner beeps and the LED turns green. For more information on beeper and LED definitions, see Table 2-1 and Table 2-2. Scanning Decode Zone in. cm 30 76.2 20 50.8 Note: Typical performance at 68˚F (20˚C) on high quality Code 39 and UPC symbols. 10 25.4 LS 3408 FZ 0 0 2.5" 5 mil 7.25" 2.0" 7.5 mil 1.0" 10 25.4 15.75" 13 mil 100% UPC 24" 20 mil (80%MRD) 0"* 20 mil (31%MRD) 20 50.8 39.5" 26.5" 2.0"* 40 mil 67.0" 30 76.2 55 mil 4.0"* in. 0 cm 0 84.0" 10 25.4 20 50.8 30 76.2 40 101.6 50 127.0 60 152.4 70 177.8 Depth of Field *Minimum distance determined by symbol length and scan angle Figure 2-5. WLS 8400FZ Decode Zone 80 203.2 90 228.6 W i d t h o f F i e l d 2-9 2-10 WLS 8400 Product Reference Guide in. cm 12 30.5 Note: Typical performance at 73.4˚F (23˚C) on high quality Code 39 symbols. LS 3408 ER 7.5 mil 0.25" 2" in. 0 cm 0 15 mil 3" 20 mil 20.3 4 10.2 0 0 4 10.2 8 20.3 W i d t h o f 20" 10 mil 3" 8 32" 12 30.5 69" F i e l d 94" 10 25.4 20 50.8 30 76.2 40 101.6 50 127.0 60 152.4 70 177.8 80 203.2 90 228.6 100 254.0 Depth of Field in. cm 72 182.9 Note: Typical performance at 73.4˚F (23˚C) on high quality Code 39 symbols. 48 121.9 24 61.0 LS 3408 ER 0 0 W i d t h o f 24 61.0 48 121.9 55 mil 15" 180" 72 182.9 70 mil reflective * 365" 100 mil reflective in. 0 cm 0 60 152.4 120 304.8 540" 180 457.2 240 609.6 300 762.0 360 914.4 420 1066.8 480 1219.2 Depth of Field *Near range determined by degree of reflectivity and width of bar code. Figure 2-6. WLS 8400ER Decode Zone 540 1371.6 600 1524.0 F i e l d 3 Maintenance and Technical Specifications Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 Scanner Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9 3-2 WLS 8400 Product Reference Guide Maintenance and Technical Specifications Introduction This chapter provides suggested scanner maintenance, troubleshooting, technical specifications, and signal descriptions (pinouts). Maintenance Cleaning the scan window is the only maintenance required. A dirty window may affect scanning accuracy. • • • • Do not allow any abrasive material to touch the window. Remove any dirt particles with a damp cloth. Wipe the window using a tissue moistened with ammonia/water. Do not spray water or other cleaning liquids directly onto the window. 3-3 3-4 WLS 8400 Product Reference Guide Troubleshooting Table 3-1. Troubleshooting Problem Possible Causes Possible Solutions Scanner emits short low/short Scanner is powering up. medium/short high beep sequence. Normal when scanner is plugged in. Nothing happens when scan trigger No power to the scanner. is pressed. Check the system power. Ensure the power supply is connected if the configuration requires a power supply. Power supply is not plugged in. Incorrect host interface cable is used. Ensure that correct host interface cable is used. Interface/power cables are loose. Ensure all cable connections are secure. Scanner is disabled. For Simple Serial Interface (SSI), enable the scanner via the host interface. Otherwise, see the technical person in charge of scanning. If using RS-232 Nixdorf B mode, CTS is not asserted. Assert CTS line. Scanner emits short low/short medium/short high beep sequence more than once. The USB bus may put the scanner in a state where power to the scanner is cycled on and off more than once. Normal during host reset. Laser comes on, but scanner does not decode the bar code. Scanner is not programmed for the Ensure the scanner is programmed correct bar code type. to read the type of bar code being scanned. Bar code symbol is unreadable. Check the symbol to ensure it is not defaced. Try scanning test bar codes of the same bar code type. See Appendix C, Sample Bar Codes for test bar codes. Bar code is out of range from the scanner. Move scanner closer to or further from bar code. Maintenance and Technical Specifications Table 3-1. Troubleshooting (Continued) Problem Scanner emits 4 short high beeps while attempting to scan. Possible Causes Scanner has not completed USB initialization. Possible Solutions Wait several seconds and scan again. Bar code is decoded, but data is not Scanner is not programmed for the Scan the appropriate host transmitted to the host. correct host type. parameter bar codes. Scanned data is incorrectly displayed on the host. Interface cable is loose. Ensure all cable connections are secure. If 4 long low beeps are heard, a transmission error was detected. Ensure the scanner's communication parameters match the host's setting. If 5 long low beeps are heard, a conversion or format error was detected. Ensure the scanner's conversion parameters are properly configured. Scanner is not programmed to work with the host. Ensure proper host is selected. For RS-232, ensure the scanner's communication parameters match the host's settings. For a Keyboard Wedge configuration, ensure the system is programmed for the correct keyboard type, and the CAPS LOCK key is off. Ensure editing options (e.g., UPCE to UPC-A conversion) are properly programmed. Scanner emits short high/short high/short high/long low beep sequence when it is not in use. RS-232 receive error. Normal during host reset. Otherwise, ensure the scanner's RS-232 parity setting matches the host setting. Scanner emits long low/long high beep sequence while it is being programming. Input error or ’Cancel’ bar code is scanned. Ensure the correct numeric bar codes, that are within range for the parameter that is being programmed, are being scanned. Scanner emits short low/short high/ Out of ADF parameter storage short low/short high beep sequence space. while it is being programming. Erase all rules and re-program with shorter rules. 3-5 3-6 WLS 8400 Product Reference Guide Table 3-1. Troubleshooting (Continued) Problem Possible Causes Possible Solutions Scanner emits a short low/short medium/short high beep sequence after changing USB host type. The USB bus re-establishes power Normal when the USB host type is to the scanner. changed. Scanner emits 1 short high beep when it is not in use. In RS-232 mode, a character is received and Beep on option is enabled. Normal when Beep on is enabled and the scanner is in RS232 mode. If after performing these checks the symbol still does not decode, contact the distributor or call Wasp Support. See page xvii for the telephone number. Maintenance and Technical Specifications Technical Specifications Table 3-2. Technical Specifications Description Item WLS 8400FZ WLS 8400ER Power Requirements 4.5 - 14VDC Stand-By Current 50mA (max) Power Source Depending on host: • host powered • external power supply Decode Capability UPC/EAN, Bookland EAN, UPC/EAN with supplementals, Code 128, UCC/ EAN 128, ISBT 128, Code 39, Trioptic Code 39, Code 93, Code 11, Interleaved 2 of 5, Discrete 2 of 5, Codabar (NW-7), MSI, RSS. Beeper Operation User-selectable: Enable, Disable Beeper Volume User-selectable: Three levels Beeper Tone User-selectable: Three tones Scan Repetition Rate 36 scans/second Yaw Tolerance ± 50° from nominal ± 60° from nominal Pitch Tolerance ± 65° from nominal ± 65° from nominal Roll Tolerance ± 20° from nominal ± 10° from nominal Print Contrast Minimum 25% minimum reflectance differential, measured at 650 nm. Ambient Light Immunity Indoor: 450 Ft Candles (4,842 Lux) 8,000 Ft Candles (86,080 Lux) Outdoor: Durability 6.5 ft (2.0 m) drops to concrete Operating Temperature -22° to 122° F (-30° to 50° C) Storage Temperature -40° to 158° F (-40° to 70° C) Humidity 5% to 95% (non-condensing) Weight (without cable) 12.35 oz. (350 g) 450 Ft Candles (4,842 Lux) 4,000 Ft Candles (43,040 Lux) 12.56 oz. (356 g) 3-7 3-8 WLS 8400 Product Reference Guide Table 3-2. Technical Specifications (Continued) Description Item Dimensions: Height Width Depth WLS 8400FZ WLS 8400ER 7.34 in. (18.65 cm) 4.82 in. (12.25 cm) 2.93 in. (7.43 cm) Laser 650nm laser diode Laser Classifications IEC 825-1 Class 2 ESD 20 kV area discharge 8 kV contact discharge Minimum Element Width 5 mil (0.127 mm) 7.5 mil (0.191 mm) Interfaces Supported Keyboard Wedge, RS-232, USB Electrical Safety Certified Pending to UL1950, CSA C22.2 No.950. EN60950/IC950 Input Transient Protection IEC 1000-4-(2,3,4,5,6,11) EMI FCC Part 15 Class B, ICES-003 Class B European Union EMC Directive, Australian SMA, Taiwan EMC, Japan VCCI/MITI/Dentori Maintenance and Technical Specifications Scanner Signal Descriptions Bottom of Cable interface port PIN 10 PIN 1 Interface cable modular Figure 3-1. Scanner Cable Pinouts 3-9 3-10 WLS 8400 Product Reference Guide The signal descriptions in Table 3-3 apply to the connector on the scanner and are for reference only. Table 3-3. Scanner Signal Pin-outs Pin RS-232 Keyboard Wedge USB 1 Reserved Reserved Jump to Pin 6 2 Power Power Power 3 Ground Ground Ground 4 TxD KeyClock Reserved 5 RxD TermData D+ 6 RTS KeyData Jump to Pin 1 7 CTS TermClock D- 8 Reserved Reserved Reserved 9 Reserved Reserved Reserved 10 Reserved Reserved Reserved 4 User Preferences Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Scanning Sequence Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Errors While Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 User Preferences Default Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 User Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Set Default Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Beeper Tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Beeper Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Power Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Laser On Time- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Beep After Good Decode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Trigger Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8 Aim Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 4-2 WLS 8400 Product Reference Guide User Preferences Introduction The scanner can be programed to perform various functions, or activate different features. This chapter describes each user preference feature and provides the programming bar codes necessary for selecting these features for the scanner. The scanner ships with the settings shown in the User Preferences Default Table on page 4-4 (also see Chapter A, Standard Default Parameters for all host device and miscellaneous scanner defaults). If the default values suit the requirements, programming may not be necessary. Feature values are set by scanning single bar codes or short bar code sequences. The settings are stored in non-volatile memory and are preserved even when the scanner is powered down. If the USB cable is not being used, select a host type (see each host chapter for specific host information). After hearing the power-up beeps, select a host type. This only needs to be done once, upon the first power-up when connected to a new host. To return all features to their default values, scan the Set All Defaults bar code on page 45. Throughout the programming bar code menus, default values are indicated with asterisks (*). * Indicates Default *High Frequency Feature/Option Scanning Sequence Examples In most cases, only one bar code needs to be scanned to set a specific parameter value. For example, to set the beeper tone to high, simply scan the High Frequency (beeper tone) bar code listed under Beeper Tone on page 4-5. The scanner issues a fast warble beep and the LED turns green, signifying a successful parameter entry. Other parameters, such as specifying Laser On Time or setting Data Transmission Formats, require that several bar codes be scanned. See Laser On Time on page 4-7 and Scan Data Transmission Format on page 9-7 for descriptions of this procedure. Errors While Scanning Unless otherwise specified, if an error is made during a scanning sequence, just re-scan the correct parameter. 4-3 4-4 WLS 8400 Product Reference Guide User Preferences Default Parameters Table 4-1 lists the defaults for user preferences parameters. To change any option, scan the appropriate bar code(s) provided in the User Preferences section beginning on page 4-5. See Chapter A, Standard Default Parameters for all user preferences, hosts, symbologies, and miscellaneous default parameters. Table 4-1. User Preferences Default Table Parameter Default Page Number User Preferences Set Default Parameter All Defaults 4-5 Beeper Tone High 4-5 Beeper Volume High 4-6 Power Mode Continuous On 4-7 Laser On Time 3.0 sec 4-7 Beep After Good Decode Enable 4-8 Trigger Mode Level 4-8 Aim Duration 0.0 sec 4-10 User Preferences User Preferences Set Default Parameter Scanning this bar code returns all parameters to the default values listed in Table A-1 on page A-3. Set All Defaults Beeper Tone To select a decode beep frequency (tone), scan the Low Frequency, Medium Frequency, or High Frequency bar code. Low Frequency Medium Frequency *High Frequency 4-5 4-6 WLS 8400 Product Reference Guide Beeper Volume To select a beeper volume, scan the Low Volume, Medium Volume, or High Volume bar code. Low Volume Medium Volume *High Volume User Preferences Power Mode This parameter determines whether or not the scanner enters reduced power mode after a decode attempt. When in reduced power mode, the scanner draws less current from its power source. *Continuous On Reduced Power Mode Laser On Time This parameter sets the maximum time that decode processing continues during a scan attempt. It is programmable in 0.1 second increments from 0.5 to 9.9 seconds. The default Laser On Time is 3.0 seconds. To set a Laser On Time, scan the bar code below. Next, scan two numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes that correspond to the desired on time. Single digit numbers must have a leading zero. For example, to set a Laser On Time of 0.5 seconds, scan the bar code below, then scan the “0” and “5” bar codes. In case of an error, or to change the selection, scan Cancel on page D-7. Laser On Time 4-7 4-8 WLS 8400 Product Reference Guide Beep After Good Decode Scan a bar code below to select whether or not the scanner beeps after a good decode. If Do Not Beep After Good Decode is selected, the beeper still operates during parameter menu scanning and indicates error conditions. *Beep After Good Decode (Enable) Do Not Beep After Good Decode (Disable) Trigger Mode The scanner has three trigger modes that can be used to scan bar codes. The desired trigger mode can be set by using the bar codes below. Level Trigger When the trigger is pulled, an aiming dot appears for a programmable duration of time. After this time, the aiming dot automatically turns into a standard laser scanning beam for a full decode session. The laser scanning beam stays on until the laser-on timeout occurs, a decode occurs, or the trigger is released. If the trigger is released before the aiming duration expires, the laser shuts off and no decode occurs. *Level User Preferences Trigger Mode (continued) Two Stage - Option 1 When the trigger is pulled, an aiming dot appears. This aiming dot remains while the trigger is pulled. When the trigger is released, the aiming dot automatically turns into a standard laser scanning beam for a full decode session. The laser scanning beam stays on until the laser-on timeout occurs or a decode occurs. If the trigger is pulled again while in a decode session, the scanner beam returns to an aiming dot. Two Stage - Option 1 Two Stage - Option 2 When the trigger is pulled, an aiming dot appears. When the trigger is released, the aiming dot turns off. Pulling the trigger twice in rapid succession turns on the standard laser scanning beam for a full decode session. The laser scanning beam, stays on until the laseron timeout occurs, a decode occurs, or the trigger is released. Two Stage - Option 2 4-9 4-10 WLS 8400 Product Reference Guide Aim Duration When the scanner is in Level trigger mode (default mode), Aim Duration sets the amount of time the aiming dot is seen before turning into a scanning beam. This parameter has no affect when the scanner is in either of the Two Stage trigger modes. See Trigger Mode on page 4-8 for a description of each of the trigger modes. The aim duration is programmable in 0.1 second increments, from 0.0 to 9.9 seconds. The default Aim Duration is 0.0 seconds. When set to 0.0 seconds, no aiming pattern appears before a decode session. To set an aim duration, scan the bar code below. Then scan two numeric bar codes, available in Appendix D, Numeric Bar Codes, that correspond to the desired aim duration. Durations less than 1.0 seconds must have a leading zero. For example, to set an aim duration of 0.5 seconds, scan the bar code below, followed by the ‘0’ and the ‘5’ bar codes. In case of an error, or to change the selection, scan the ‘Cancel’ bar code on page D-7. Aim Duration 5 Keyboard Wedge Interface Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Connecting a Keyboard Wedge Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 Keyboard Wedge Default Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Keyboard Wedge Host Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6 Keyboard Wedge Host Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6 Keyboard Wedge Country Types (Country Codes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7 Ignore Unknown Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9 Keystroke Delay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9 Intra-Keystroke Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10 Alternate Numeric Keypad Emulation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11 Caps Lock On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11 Caps Lock Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12 Convert Wedge Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13 Function Key Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13 FN1 Substitution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14 Send Make and Break . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14 5-2 WLS 8400 Product Reference Guide Keyboard Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-15 ASCII Character Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-18 Keyboard Wedge Interface Introduction This chapter provides Keyboard Wedge interface information for setting up the scanner. This interface type is used to attach the scanner between the keyboard and host computer. The scanner translates the bar code data into keystrokes. The host computer accepts the keystrokes as if they originate from the keyboard. This mode of operation allows adding bar code reading functionality to a system designed for manual keyboard input. In this mode, the keyboard keystrokes are simply passed through. Throughout the programming bar code menus, default values are indicated with asterisks (*). * Indicates Default *North American Feature/Option 5-3 5-4 WLS 8400 Product Reference Guide Connecting a Keyboard Wedge Interface Male DIN Host Y-cable Keyboard Female DIN Keyboard Figure 5-1. Keyboard Wedge Interface Connection with Y-cable To connect the keyboard wedge interface Y-cable: Interface cables vary depending on configuration. The connectors illustrated in Figure 5-1 are examples only. The connectors may be different than those illustrated, but the steps to connect the scanner remain the same. 1. Turn off the host and unplug the keyboard connector. 2. Attach the modular connector of the Y-cable to the cable interface port on the scanner. (See Installing the Interface Cable on page 1-5.) 3. Connect the round male DIN host connector of the Y-cable to the keyboard port on the host. 4. Connect the round female DIN keyboard connector of the Y-cable to the keyboard connector. 5. If required, attach the optional power supply to the connector in the middle of the Y-cable. 6. Ensure that all connections are secure. Keyboard Wedge Interface 7. Turn on the host system. 8. Select the Keyboard Wedge host type by scanning the appropriate bar code from the Keyboard Wedge Host Types section on page 5-7. 9. To modify any other parameter options, scan the appropriate bar codes in this chapter. Keyboard Wedge Default Parameters Table 5-1 lists the defaults for Keyboard Wedge host parameters. To change any option, scan the appropriate bar code(s) provided in the Keyboard Wedge Host Parameters section beginning on page 5-7. See Chapter A, Standard Default Parameters for all user preferences, hosts, symbologies, and miscellaneous default parameters. Table 5-1. Keyboard Wedge Host Default Table Parameter Default Page Number Keyboard Wedge Host Parameters Keyboard Wedge Host Type IBM PC/AT& IBM PC Compatibles 5-7 Keyboard Wedge Country Types (Country Codes) North American 5-8 Ignore Unknown Characters Enable 5-10 Keystroke Delay 0 msec (No Delay) 5-10 Intra-Keystroke Delay Disable 5-11 Alternate Numeric Keypad Emulation Disable 5-12 Caps Lock On Disable 5-12 Caps Lock Override Disable 5-13 Convert Wedge Data Do Not Convert Wedge Data 5-14 Function Key Mapping Disable 5-15 5-5 5-6 WLS 8400 Product Reference Guide Table 5-1. Keyboard Wedge Host Default Table (Continued) Parameter Default Page Number FN1 Substitution Disable 5-15 Send Make and Break Send Make and Break Scan Codes 5-15 Keyboard Wedge Interface Keyboard Wedge Host Types Keyboard Wedge Host Types Select the keyboard wedge host by scanning one of the bar codes below. *IBM PC/AT & IBM PC Compatibles IBM PS/2 (Model 30) IBM AT NOTEBOOK IBM XT NCR 7052 5-7 5-8 WLS 8400 Product Reference Guide Keyboard Wedge Country Types (Country Codes) Scan the bar code corresponding to the keyboard type. If the particular keyboard type is not listed, see Alternate Numeric Keypad Emulation on page 5-12. *North American German Windows French Windows French Canadian Windows 95/98 French Canadian Windows XP/2000 Keyboard Wedge Interface Keyboard Wedge Country Types (Country Codes) (continued) Spanish Windows Italian Windows Swedish Windows UK English Windows Japanese Windows Brazilian-Portuguese Windows 5-9 5-10 WLS 8400 Product Reference Guide Ignore Unknown Characters Unknown characters are characters the host does not recognize. When Send Bar Codes With Unknown Characters is selected, all bar code data is sent except for unknown characters, and no error beeps sound on the scanner. When Do Not Send Bar Codes With Unknown Characters is selected, bar code data is sent up to the first unknown character and then an error beep sounds on the scanner. *Send Bar Codes with Unknown Characters (Enable) Do Not Send Bar Codes with Unknown Characters (Disable) Keystroke Delay This is the delay in milliseconds between emulated keystrokes. Scan a bar code below to increase the delay when hosts require a slower transmission of data. *0 msec (No Delay) 20 msec (Medium Delay) Keyboard Wedge Interface Keystroke Delay (continued) 40 msec (Long Delay) Intra-Keystroke Delay When enabled, an additional delay is inserted between each emulated key depression and release. This sets the Keystroke Delay parameter to a minimum of 5 msec, as well. Enable Intra-Keystroke Delay *Disable Intra-Keystroke Delay 5-11 5-12 WLS 8400 Product Reference Guide Alternate Numeric Keypad Emulation This allows emulation of most other country keyboard types not listed in Keyboard Wedge Country Types (Country Codes) on page 5-8 in a Microsoft® operating system environment. Enable Alternate Numeric Keypad *Disable Alternate Numeric Keypad Caps Lock On When enabled, the scanner emulates keystrokes as if the Caps Lock key is always pressed. Enable Caps Lock On *Disable Caps Lock On Keyboard Wedge Interface Caps Lock Override When enabled, on AT or AT Notebook hosts, the keyboard ignores the state of the Caps Lock key. Therefore, an ‘A’ in the bar code is sent as an ‘A’ no matter what the state of the keyboard’s Caps Lock key. Enable Caps Lock Override *Disable Caps Lock Override If both Caps Lock On and Caps Lock Override are enabled, Caps Lock Override takes precedence. 5-13 5-14 WLS 8400 Product Reference Guide Convert Wedge Data When enabled, the scanner converts all bar code data to the selected case. Convert Wedge Data to Upper Case Convert Wedge Data to Lower Case *Do Not Convert Wedge Data Function Key Mapping ASCII values under 32 are normally sent as control key sequences (see Table 5-2 on page 5-19). When this parameter is enabled, the keys in bold are sent in place of the standard key mapping. Table entries that do not have a bold entry remain the same whether or not this parameter is enabled. Enable Function Key Mapping *Disable Function Key Mapping Keyboard Wedge Interface FN1 Substitution When enabled, this parameter allows replacement of any FN1 characters in an EAN128 bar code with a keystroke chosen by the user. (see FN1 Substitution Values on page 9-9). Enable FN1 Substitution *Disable FN1 Substitution Send Make and Break When enabled, the scan codes for releasing a key are not sent. *Send Make and Break Scan Codes Send Make Scan Code Only 5-15 5-16 WLS 8400 Product Reference Guide Keyboard Maps The following keyboard maps are provided for prefix/suffix keystroke parameters. To program the prefix/suffix values, see the bar codes on page 9-6. 7014 5001 5002 5003 5004 5005 5006 5007 5008 5009 5010 5011 5012 7008 7009 7010 7007 7006 7001 7011 7012 7003 7002 7004 7005 7013 7015 7017 7016 7018 Figure 5-2. IBM PS2 Type Keyboard 5001 5002 5003 5004 7008 7014 7009 7012 7003 7004 7006 7013 5005 5006 5007 5008 5009 5010 7011 Figure 5-3. IBM PC/XT 7002 Keyboard Wedge Interface 5001 5002 5003 5004 7008 7009 7014 7012 7003 7013 5005 5006 5007 5008 5009 5010 7004 7011 Figure 5-4. IBM PC/AT 5001 5002 1045 5013 5003 5004 5014 5015 5005 5006 1043 5016 5007 5008 5017 5018 5009 5010 7013 5019 5011 1048 5012 (1048 if double key) 1046 (7013 if double key) Figure 5-5. NCR 7052 32-KEY 7002 5-17 5-18 WLS 8400 Product Reference Guide 1065 1066 1067 1068 1072 1073 1074 1079 1080 1081 5001 5002 5011 5003 1069 1070 1071 1075 1076 1077 1078 1082 1083 1084 1085 1045 5013 1086 5004 5014 5015 1087 5005 5006 1043 5016 1088 5007 5008 5017 5018 1089 5009 5010 7013 5019 1090 1048 5012 (1048 if double key) 1046 (1043 if double key) Figure 5-6. NCR 7052 58-KEY Keyboard Wedge Interface ASCII Character Set Code 39 Full ASCII interprets the bar code special character ($ + % /) preceding a Code 39 character and assigns an ASCII character value to the pair. For example, when Code 39 Full ASCII is enabled and a +B is scanned, it is interpreted as b, %J as ?, and %V as @. Scanning ABC%I outputs the keystroke equivalent of ABC >. Table 5-2. Keyboard Wedge ASCII Character Set Full ASCII Code 39 Encode Character ASCII Value Keystroke 1001 $A CTRL A 1002 $B CTRL B 1003 $C CTRL C 1004 $D CTRL D 1005 $E CTRL E 1006 $F CTRL F 1007 $G CTRL G 1008 $H CTRL H/ BACKSPACE1 1009 $I CTRL I/ HORIZONTAL TAB1 1010 $J CTRL J 1011 $K CTRL K 1012 $L CTRL L 1013 $M CTRL M/ENTER1 1014 $N CTRL N 1015 $O CTRL O 1016 $P CTRL P 1017 $Q CTRL Q 1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the unbolded keystroke is sent. 5-19 5-20 WLS 8400 Product Reference Guide Table 5-2. Keyboard Wedge ASCII Character Set (Continued) Full ASCII Code 39 Encode Character ASCII Value Keystroke 1018 $R CTRL R 1019 $S CTRL S 1020 $T CTRL T 1021 $U CTRL U 1022 $V CTRL V 1023 $W CTRL W 1024 $X CTRL X 1025 $Y CTRL Y 1026 $Z CTRL Z 1027 %A CTRL [ /ESC1 1028 %B CTRL \ 1029 %C CTRL ] 1030 %D CTRL 6 1031 %E CTRL - 1032 Space Space 1033 /A ! 1034 /B “ 1035 /C # 1036 /D $ 1037 /E % 1038 /F & 1039 /G ‘ 1040 /H ( 1041 /I ) 1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the unbolded keystroke is sent. Keyboard Wedge Interface Table 5-2. Keyboard Wedge ASCII Character Set (Continued) Full ASCII Code 39 Encode Character ASCII Value Keystroke 1042 /J * 1043 /K + 1044 /L , 1045 - - 1046 . . 1047 /O / 1048 0 0 1049 1 1 1050 2 2 1051 3 3 1052 4 4 1053 5 5 1054 6 6 1055 7 7 1056 8 8 1057 9 9 1058 /Z : 1059 %F ; 1060 %G < 1061 %H = 1062 %I > 1063 %J ? 1064 %V @ 1065 A A 1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the unbolded keystroke is sent. 5-21 5-22 WLS 8400 Product Reference Guide Table 5-2. Keyboard Wedge ASCII Character Set (Continued) Full ASCII Code 39 Encode Character ASCII Value Keystroke 1066 B B 1067 C C 1068 D D 1069 E E 1070 F F 1071 G G 1072 H H 1073 I I 1074 J J 1075 K K 1076 L L 1077 M M 1078 N N 1079 O O 1080 P P 1081 Q Q 1082 R R 1083 S S 1084 T T 1085 U U 1086 V V 1087 W W 1088 X X 1089 Y Y 1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the unbolded keystroke is sent. Keyboard Wedge Interface Table 5-2. Keyboard Wedge ASCII Character Set (Continued) Full ASCII Code 39 Encode Character ASCII Value Keystroke 1090 Z Z 1091 %K [ 1092 %L \ 1093 %M ] 1094 %N ^ 1095 %O _ 1096 %W ‘ 1097 +A a 1098 +B b 1099 +C c 1100 +D d 1101 +E e 1102 +F f 1103 +G g 1104 +H h 1105 +I i 1106 +J j 1107 +K k 1108 +L l 1109 +M m 1110 +N n 1111 +O o 1112 +P p 1113 +Q q 1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the unbolded keystroke is sent. 5-23 5-24 WLS 8400 Product Reference Guide Table 5-2. Keyboard Wedge ASCII Character Set (Continued) ASCII Value Full ASCII Code 39 Encode Character Keystroke 1114 +R r 1115 +S s 1116 +T t 1117 +U u 1118 +V v 1119 +W w 1120 +X x 1121 +Y y 1122 +Z z 1123 %P { 1124 %Q | 1125 %R } 1126 %S ~ 1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the unbolded keystroke is sent. Keyboard Wedge Interface Table 5-3. Keyboard Wedge ALT Key Character Set ALT Keys Keystroke 2065 ALT A 2066 ALT B 2067 ALT C 2068 ALT D 2069 ALT E 2070 ALT F 2071 ALT G 2072 ALT H 2073 ALT I 2074 ALT J 2075 ALT K 2076 ALT L 2077 ALT M 2078 ALT N 2079 ALT O 2080 ALT P 2081 ALT Q 2082 ALT R 2083 ALT S 2084 ALT T 2085 ALT U 2086 ALT V 2087 ALT W 2088 ALT X 2089 ALT Y 2090 ALT Z 5-25 5-26 WLS 8400 Product Reference Guide Table 5-4. Keyboard Wedge GUI Key Character Set GUI Keys Keystrokes 3000 Right Control Key 3048 GUI 0 3049 GUI 1 3050 GUI 2 3051 GUI 3 3052 GUI 4 3053 GUI 5 3054 GUI 6 3055 GUI 7 3056 GUI 8 3057 GUI 9 3065 GUI A 3066 GUI B 3067 GUI C 3068 GUI D 3069 GUI E 3070 GUI F 3071 GUI G 3072 GUI H 3073 GUI I 3074 GUI J 3075 GUI K 3076 GUI L 3077 GUI M 3078 GUI N 3079 GUI O 3080 GUI P Keyboard Wedge Interface Table 5-4. Keyboard Wedge GUI Key Character Set (Continued) GUI Keys Keystrokes 3081 GUI Q 3082 GUI R 3083 GUI S 3084 GUI T 3085 GUI U 3086 GUI V 3087 GUI W 3088 GUI X 3089 GUI Y 3090 GUI Z Table 5-5. Keyboard Wedge F Key Character Set F Keys Keystroke 5001 F1 5002 F2 5003 F3 5004 F4 5005 F5 5006 F6 5007 F7 5008 F8 5009 F9 5010 F10 5011 F11 5012 F12 5-27 5-28 WLS 8400 Product Reference Guide Table 5-5. Keyboard Wedge F Key Character Set (Continued) F Keys Keystroke 5013 F13 5014 F14 5015 F15 5016 F16 5017 F17 5018 F18 5019 F19 5020 F20 5021 F21 5022 F22 5023 F23 5024 F24 Table 5-6. Keyboard Wedge Numeric Keypad Character Set Numeric Keypad Keystroke 6042 * 6043 + 6044 undefined 6045 - 6046 . 6047 / 6048 0 6049 1 6050 2 6051 3 Keyboard Wedge Interface Table 5-6. Keyboard Wedge Numeric Keypad Character Set (Continued) Numeric Keypad Keystroke 6052 4 6053 5 6054 6 6055 7 6056 8 6057 9 6058 Enter 6059 Num Lock Table 5-7. Keyboard Wedge Extended Keypad Character Set Extended Keypad Keystroke 7001 Break 7002 Delete 7003 Pg Up 7004 End 7005 Pg Dn 7006 Pause 7007 Scroll Lock 7008 Backspace 7009 Tab 7010 Print Screen 7011 Insert 7012 Home 7013 Enter 7014 Escape 5-29 5-30 WLS 8400 Product Reference Guide Table 5-7. Keyboard Wedge Extended Keypad Character Set (Continued) Extended Keypad Keystroke 7015 Up Arrow 7016 Dn Arrow 7017 Left Arrow 7018 Right Arrow 6 RS-232 Interface Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Connecting an RS-232 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 RS-232 Default Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5 RS-232 Host Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6 RS-232 Host Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8 Baud Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9 Parity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11 Check Receive Errors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12 Stop Bit Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13 Data Bits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13 Hardware Handshaking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-14 Software Handshaking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-17 Host Serial Response Time-out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-19 RTS Line State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-20 Beep on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-21 Intercharacter Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-22 6-2 WLS 8400 Product Reference Guide Nixdorf Mode A/B and OPOS/JPOS Beep/LED Options . . . . . . . . . . . . . . . . . . . . . . 6-23 Ignore Unknown Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-24 ASCII / Character Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-25 RS-232 Interface Introduction This chapter provides RS-232 host information for setting up the scanner. The RS-232 interface is used to attach the scanner to point-of-sale devices, host computers, or other devices with an available RS-232 port (i.e., com port). If the particular host is not listed in Table 6-2, set the communication parameters to match the host device. To set communication parameters for hosts not listed, refer to the documentation for the host device. This scanner utilizes TTL RS-232 signal levels, which interfaces with most system architectures. Please contact Wasp Support for more information. Throughout the programming bar code menus, default values are indicated with asterisks (*). * Indicates Default *Baud Rate 9600 Feature/Option 6-3 6-4 WLS 8400 Product Reference Guide Connecting an RS-232 Interface This connection is made directly from the scanner to the host computer. Serial Port Connector to Interface Power supply Figure 6-1. RS-232 Direct Connection Interface cables vary depending on configuration. The connectors illustrated in Figure 6-1 are examples only. The connectors may be different than those illustrated, but the steps to connect the scanner remain the same. 1. Attach the modular connector of the RS-232 interface cable to the cable interface port on the scanner. (See Installing the Interface Cable on page 1-5.) 2. Connect the other end of the RS-232 interface cable to the serial port on the host. 3. Connect the power supply to the serial connector end of the RS-232 interface cable. Plug the power supply to an appropriate outlet. 4. Ensure that all connections are secure. 5. Select the RS-232 host type by scanning the appropriate bar code from the RS-232 Host Types section on page 6-9. 6. To modify any other parameter options, scan the appropriate bar codes in this chapter. RS-232 Interface RS-232 Default Parameters Table 6-1 lists the defaults for RS-232 host parameters. To change any option, scan the appropriate bar code(s) provided in the Parameter Descriptions section beginning on page 6-6. See Chapter A, Standard Default Parameters for all user preferences, hosts, symbologies, and miscellaneous default parameters. Table 6-1. RS-232 Host Default Table Parameter Default Page Number RS-232 Host Parameters RS-232 Host Types Standard RS-232 6-9 Baud Rate 9600 6-11 Parity None 6-13 Check Receive Errors Enable 6-13 Stop Bit Select 1 Stop Bit 6-14 Data Bits 8-Bit 6-14 Hardware Handshaking None 6-16 Software Handshaking None 6-18 Host Serial Response Time-out Minimum: 2 sec 6-20 RTS Line State Host: Low RTS 6-21 Beep on Disable 6-22 Intercharacter Delay Minimum: 0 msec 6-23 Nixdorf Beep/LED Options Normal Operation 6-24 Ignore Unknown Characters Send Bar Code 6-25 6-5 6-6 WLS 8400 Product Reference Guide RS-232 Host Parameters Various RS-232 host types are set up with their own parameter default settings. Selecting the host type sets the parameter defaults as listed in Table 6-2. Table 6-2. Terminal Specific RS-232 Parameter Transmit Code ID Standard RS-232 (Default) No Data as is Data Transmission Format ICL WincorNixdorf Mode A WincorNixdorf Mode B Olivetti Omron OPOS/ JPOS Fujitsu Yes Yes Yes Yes Yes Yes Yes Data/ Suffix Data/ Suffix Data/ Suffix Prefix/ Data/ Suffix Data/ Suffix Data/ Suffix Data/ Suffix CR/LF (7013) CR (1013) CR (1013) CR (1013) ETX (1002) CR (1013) CR (1013) CR (1013) Suffix Baud Rate 9600 9600 9600 9600 9600 9600 9600 9600 Parity None Even Odd Odd Even None Odd None Hardware Handshaking None RTS/CTS Option 3 RTS/CTS Option 3 RTS/CTS Option 3 None None RTS/CTS Option 3 None Software Handshaking None None None None Ack/Nak None None None Serial Response Time-out 2 Sec. 9.9 Sec. 30.0 Sec. 30.0 Sec. 9.9 Sec. 9.9 Sec. 30.0 Sec. 2 Sec. Stop Bit Select One One One One One One One One ASCII Format 8-Bit 8-Bit 8-Bit 8-Bit 7-Bit 8-Bit 8-Bit 8-Bit Beep On Disable Disable Disable Disable Disable Disable Disable Disable Low High Low Low = No Low data to send High Low = No Low data to send None None None None None None RTS Line State Prefix STX (1003) None RS-232 Interface Table 6-2. Terminal Specific RS-232 Parameter Standard RS-232 (Default) ICL WincorNixdorf Mode A WincorNixdorf Mode B Olivetti Omron OPOS/ JPOS Fujitsu *In the Nixdorf Mode B or OPOS/JPOS, if CTS is Low, scanning is disabled. When CTS is High, the user can scan bar codes. **If Nixdorf Mode B or OPOS/JPOS is scanned without the scanner connected to the proper host, it may appear unable to scan. If this happens, scan a different RS-232 host type within 5 seconds of cycling power to the scanner. 6-7 6-8 WLS 8400 Product Reference Guide RS-232 Host Parameters (continued) Selecting the ICL, Wincor-Nixdorf Mode A, Wincor-Nixdorf Mode B, Olivetti, Omron, OPOS/JPOS or Fujitsu host type enables the transmission of code ID characters listed in Table 6-3 below. These code ID characters are not programmable and are separate from the Transmit Code ID feature. The Transmit Code ID feature should not be enabled for these terminals. Table 6-3. Terminal Specific Code ID Characters WincorNixdorf Mode A ICL WincorNixdorf Mode B Olivetti OPOS/ JPOS Omron Fujitsu UPC-A A A A A A A A UPC-E E C C C E C E EAN-8/JAN-8 FF B B B FF B FF EAN-13/JAN13 F A A A F A F Code 39 C M M M C M None Codabar N N N N N N None Code 128 L K K K L K None I 2 of 5 I I I I I I None Code 93 None L L L None L None D 2 of 5 H H H H H H None UCC/EAN 128 L P P P L P None MSI None O O O None O None Bookland EAN F A A A F A F Trioptic None None None None None None None Code 11 None None None None None None None IATA H H H None None H None Code 32 None None None None None None None RS-232 Interface RS-232 Host Types To select an RS-232 host type, scan one of the following bar codes. *Standard RS-232 ICL RS-232 Wincor-Nixdorf RS-232 Mode A Wincor-Nixdorf RS-232 Mode B Olivetti ORS4500 Omron 6-9 6-10 WLS 8400 Product Reference Guide RS-232 Host Types (continued) OPOS/JPOS Fujitsu RS-232 Baud Rate Baud rate is the number of bits of data transmitted per second. The scanner's baud rate setting should match the baud rate setting of the host device. If not, data may not reach the host device or may reach it in distorted form. Baud Rate 600 Baud Rate 1200 Baud Rate 2400 RS-232 Interface Baud Rate (continued) Baud Rate 4800 *Baud Rate 9600 Baud Rate 19,200 Baud Rate 38,400 6-11 6-12 WLS 8400 Product Reference Guide Parity A parity check bit is the most significant bit of each ASCII coded character. Select the parity type according to host device requirements. Select Odd parity with the parity bit value set to 0 or 1, based on data, to ensure that an odd number of 1 bits are contained in the coded character. Odd Select Even parity with the parity bit value set to 0 or 1, based on data, to ensure that an even number of 1 bits are contained in the coded character. Even Select Mark parity and the parity bit is always 1. Mark RS-232 Interface Parity (continued) Select Space parity and the parity bit is always 0. Space Select None when no parity bit is required. *None Check Receive Errors Select whether or not the parity, framing, and overrun of received characters are checked. The parity value of received characters is verified against the parity parameter selected above. *Check For Received Errors (Enable) Do Not Check For Received Errors (Disable) 6-13 6-14 WLS 8400 Product Reference Guide Stop Bit Select The stop bit(s) at the end of each transmitted character marks the end of transmission of one character and prepares the receiving device for the next character in the serial data stream. The number of stop bits selected (one or two) depends on the number the receiving terminal is programmed to accommodate. Set the number of stop bits to match host device requirements. *1 Stop Bit 2 Stop Bits Data Bits This parameter allows the scanner to interface with devices requiring a 7-bit or 8-bit ASCII protocol. 7-Bit *8-Bit RS-232 Interface Hardware Handshaking The data interface consists of an RS-232 port designed to operate either with or without the hardware handshaking lines, Request to Send (RTS), and Clear to Send (CTS). If Standard RTS/CTS handshaking is not selected, scan data is transmitted as it becomes available. If Standard RTS/CTS handshaking is selected, scan data is transmitted according to the following sequence: • • • • The scanner reads the CTS line for activity. If CTS is de-asserted, the scanner waits up to the Host Serial Response Time-out for the host to de-assert the CTS line. If, after Host Serial Response Time-out (default), the CTS line is still asserted, the scanner sounds a transmit error, and any scanned data is lost. When the CTS line is de-asserted, the scanner asserts the RTS line and waits up to the Host Serial Response Time-out for the host to assert CTS. When the host asserts CTS, data is transmitted. If, after Host Serial Response Time-out (default), the CTS line is still de-asserted, the scanner sounds a transmit error, and discards the data. When data transmission is complete, the scanner de-asserts RTS 10 msec after sending the last character. The host should respond by de-asserting CTS. The scanner checks for a de-asserted CTS upon the next transmission of data. During the transmission of data, the CTS line should be asserted. If CTS is de-asserted for more than 50 ms between characters, the transmission is aborted, the scanner sounds a transmission error, and the data is discarded. If the above communications sequence fails, the scanner issues an error indication. In this case, the data is lost and must be rescanned. If Hardware Handshaking and Software Handshaking are both enabled, Hardware Handshaking takes precedence. The DTR signal is jumped to the active state. 6-15 6-16 WLS 8400 Product Reference Guide Hardware Handshaking (continued) None Scan the bar code below if no Hardware Handshaking is desired. *None Standard RTS/CTS Scan the bar code below to select Standard RTS/CTS Hardware Handshaking. Standard RTS/CTS RTS/CTS Option 1 When RTS/CTS Option 1 is selected, the scanner asserts RTS before transmitting and ignores the state of CTS. The scanner de-asserts RTS when the transmission is complete. RTS/CTS Option 1 RS-232 Interface Hardware Handshaking (continued) RTS/CTS Option 2 When Option 2 is selected, RTS is always high or low (user-programmed logic level). However, the scanner waits for CTS to be asserted before transmitting data. If CTS is not asserted within Host Serial Response Time-out (default), the scanner issues an error indication and discards the data. RTS/CTS Option 2 RTS/CTS Option 3 When Option 3 is selected, the scanner asserts RTS prior to any data transmission, regardless of the state of CTS. The scanner waits up to Host Serial Response Time-out (default) for CTS to be asserted. If CTS is not asserted during this time, the scanner issues an error indication and discards the data. The scanner de-asserts RTS when transmission is complete. RTS/CTS Option 3 6-17 6-18 WLS 8400 Product Reference Guide Software Handshaking This parameter offers control of the data transmission process in addition to, or instead of, that offered by hardware handshaking. There are five options. If Software Handshaking and Hardware Handshaking are both enabled, Hardware Handshaking takes precedence. None When this option is selected, data is transmitted immediately. No response is expected from host. *None ACK/NAK When this option is selected, after transmitting data, the scanner expects either an ACK or NAK response from the host. When a NAK is received, the scanner transmits the same data again and waits for either an ACK or NAK. After three unsuccessful attempts to send data when NAKs are received, the scanner issues an error indication and discards the data. The scanner waits up to the programmable Host Serial Response Time-out to receive an ACK or NAK. If the scanner does not get a response in this time, it issues an error indication and discards the data. There are no retries when a time-out occurs. ACK/NAK RS-232 Interface Software Handshaking (continued) ENQ When this option is selected, the scanner waits for an ENQ character from the host before transmitting data. If an ENQ is not received within the Host Serial Response Time-out, the scanner issues an error indication and discards the data. The host must transmit an ENQ character at least every Host Serial Response Time-out to prevent transmission errors. ENQ ACK/NAK with ENQ This combines the two previous options. For re-transmissions of data, due to a NAK from the host, an additional ENQ is not required. ACK/NAK with ENQ XON/XOFF An XOFF character turns the scanner transmission off until the scanner receives an XON character. There are two situations for XON/XOFF: • • XOFF is received before the scanner has data to send. When the scanner has data to send, it waits up to Host Serial Response Time-out for an XON character before transmission. If the XON is not received within this time, the scanner issues an error indication and discards the data. XOFF is received during a transmission. Data transmission then stops after sending the current byte. When the scanner receives an XON character, it sends the rest of the data message. The scanner waits up to 30 seconds for the XON. XON/XOFF 6-19 6-20 WLS 8400 Product Reference Guide Host Serial Response Time-out This parameter specifies how long the scanner waits for an ACK, NAK, or CTS before determining that a transmission error has occurred. This only applies when in one of the ACK/NAK Software Handshaking modes, or RTS/CTS Hardware Handshaking option. This parameter does not apply to the Wincor-Nixdorf RS-232 Mode A/B and the OPOS/JPOS host types. *Minimum: 2 sec Low: 2.5 Sec Medium: 5 Sec RS-232 Interface Host Serial Response Time-out (continued) High: 7.5 Sec Maximum: 9.9 Sec RTS Line State This parameter sets the idle state of the Serial Host RTS line. Scan a bar code below to select Low RTS or High RTS line state. *Host: Low RTS Host: High RTS 6-21 6-22 WLS 8400 Product Reference Guide Beep on When this parameter is enabled, the scanner issues a beep when a character is detected on the RS-232 serial line. is issued to gain a user's attention to an illegal entry or other important event. Beep On Character (Enable) *Do Not Beep On Character (Disable) RS-232 Interface Intercharacter Delay This parameter specifies the intercharacter delay inserted between character transmissions. *Minimum: 0 msec Low: 25 msec Medium: 50 msec High: 75 msec Maximum: 99 msec 6-23 6-24 WLS 8400 Product Reference Guide Nixdorf Mode A/B and OPOS/JPOS Beep/LED Options When Nixdorf Mode A, Nixdorf Mode B or OPOS/JPOS is selected, this parameter indicates when the scanner should beep and turn on its LED after a decode. The Beep/LED After CTS Pulse option is not valid when Nixdorf Mode A is selected. *Normal Operation (Beep/LED Immediately After Decode) Beep/LED After Transmission Beep/LED After CTS Pulse RS-232 Interface Ignore Unknown Characters Unknown characters are characters the host does not recognize. When Send Bar Codes with Unknown Characters is selected, all bar code data is send except for unknown characters, and no error beeps sound on the scanner. When Do Not Send Bar Codes With Unknown Characters is selected, bar code data is sent up to the first unknown character and then an error beep sounds on the scanner. *Send Bar Code (with unknown characters) Do Not Send Bar Codes (with unknown characters) 6-25 6-26 WLS 8400 Product Reference Guide ASCII / Character Set The values in Table 6-4 can be assigned as prefixes or suffixes for ASCII character data transmission. Table 6-4. RS-232 Prefix/Suffix Values Prefix/Suffix Value Full ASCII Code 39 Encode Character ASCII Character 1000 %U NUL 1001 $A SOH 1002 $B STX 1003 $C ETX 1004 $D EOT 1005 $E ENQ 1006 $F ACK 1007 $G BELL 1008 $H BCKSPC 1009 $I HORIZ TAB 1010 $J LF/NW LN 1011 $K VT 1012 $L FF 1013 $M CR/ENTER 1014 $N SO 1015 $O SI 1016 $P DLE 1017 $Q DC1/XON 1018 $R DC2 1019 $S DC3/XOFF 1020 $T DC4 1021 $U NAK 1022 $V SYN 1023 $W ETB RS-232 Interface Table 6-4. RS-232 Prefix/Suffix Values (Continued) Prefix/Suffix Value Full ASCII Code 39 Encode Character ASCII Character 1024 $X CAN 1025 $Y EM 1026 $Z SUB 1027 %A ESC 1028 %B FS 1029 %C GS 1030 %D RS 1031 %E US 1032 Space Space 1033 /A ! 1034 /B " 1035 /C # 1036 /D $ 1037 /E % 1038 /F & 1039 /G ‘ 1040 /H ( 1041 /I ) 1042 /J * 1043 /K + 1044 /L , 1045 - - 1046 . . 1047 /O / 1048 0 0 1049 1 1 1050 2 2 6-27 6-28 WLS 8400 Product Reference Guide Table 6-4. RS-232 Prefix/Suffix Values (Continued) Prefix/Suffix Value Full ASCII Code 39 Encode Character ASCII Character 1051 3 3 1052 4 4 1053 5 5 1054 6 6 1057 7 7 1056 8 8 1057 9 9 1058 /Z : 1059 %F ; 1060 %G < 1061 %H = 1062 %I > 1063 %J ? 1064 %V @ 1065 A A 1066 B B 1067 C C 1068 D D 1069 E E 1070 F F 1071 G G 1072 H H 1073 I I 1074 J J 1075 K K 1076 L L 1077 M M RS-232 Interface Table 6-4. RS-232 Prefix/Suffix Values (Continued) Prefix/Suffix Value Full ASCII Code 39 Encode Character ASCII Character 1078 N N 1079 O O 1080 P P 1081 Q Q 1082 R R 1083 S S 1084 T T 1085 U U 1086 V V 1087 W W 1088 X X 1089 Y Y 1090 Z Z 1091 %K [ 1092 %L \ 1093 %M ] 1094 %N ^ 1095 %O _ 1096 %W ` 1097 +A a 1098 +B b 1099 +C c 1100 +D d 1101 +E e 1102 +F f 1103 +G g 1104 +H h 6-29 6-30 WLS 8400 Product Reference Guide Table 6-4. RS-232 Prefix/Suffix Values (Continued) Prefix/Suffix Value Full ASCII Code 39 Encode Character ASCII Character 1105 +I i 1106 +J j 1107 +K k 1108 +L l 1109 +M m 1110 +N n 1111 +O o 1112 +P p 1113 +Q q 1114 +R r 1115 +S s 1116 +T t 1117 +U u 1118 +V v 1119 +W w 1120 +X x 1121 +Y y 1122 +Z z 1123 %P { 1124 %Q | 1125 %R } 1126 %S ~ 1127 Undefined 7013 ENTER 7 USB Interface Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 Connecting a USB Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-4 USB Default Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6 USB Host Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7 USB Device Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7 USB Country Keyboard Types (Country Codes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8 USB Keystroke Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10 USB CAPS Lock Override . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11 USB Ignore Unknown Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12 Emulate Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12 USB Keyboard FN 1 Substitution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13 Function Key Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13 Simulated Caps Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14 Convert Case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14 ASCII Character Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15 7-2 WLS 8400 Product Reference Guide USB Interface Introduction This chapter provides the connection and setup of the scanner to a USB host. The scanner attaches directly to a USB host, or a powered USB hub, and is powered by it. No additional power supply is required. Throughout the programming bar code menus, default values are indicated with asterisks (*). * Indicates Default *North American Standard USB Keyboard Feature/Option 7-3 7-4 WLS 8400 Product Reference Guide Connecting a USB Interface USB Series A Interface Figure 7-1. USB Connection The scanner connects with USB capable hosts including: • • • • Desktop PCs and notebooks Apple™ iMacs, Power Mac G4s and G5s, iBooks (North America only), PowerBooks IBM SurePOS terminals Sun, IBM, and other network computers that support more than one keyboard. The following operating systems support the scanner through USB: • • • Windows® 98, 2000, ME, XP Mac OS 8.5 and above IBM 4690 OS. The scanner also interfaces with other USB hosts which support USB Human Interface Devices (HID). USB Interface To set up the scanner: Interface cables vary depending on configuration. The connectors illustrated in Figure 7-1 are examples only. The connectors may be different than those illustrated, but the steps to connect the scanner remain the same. 1. Attach the modular connector of the USB interface cable to the cable interface port on the scanner. (See Installing the Interface Cable on page 1-5.) 2. Plug the series A connector in the USB host or hub, or plug the Plus Power connector in an available port of the IBM SurePOS terminal. 3. Ensure that all connections are secure. 4. Select the USB device type by scanning the appropriate bar code from the USB Device Type section on page 7-7. 5. On first installation when using Windows, the software displays a prompt to select or install the "Human Interface Device" driver. To install the "Human Interface Device" driver provided by Windows click "Next" through all the choices and click "Finished" on the last choice. The scanner powers up during this installation. 6. To modify any other parameter options, scan the appropriate bar codes in this chapter. If there are any problems with the system, see Troubleshooting on page 3-4. 7-5 7-6 WLS 8400 Product Reference Guide USB Default Parameters Table 7-1 lists the defaults for USB host parameters. To change any option, scan the appropriate bar code(s) provided in the Parameter Descriptions section beginning on page 7-7. See Chapter A, Standard Default Parameters for all user preferences, hosts, symbologies, and miscellaneous default parameters. Table 7-1. USB Host Default Table Parameter Default Page Number USB Host Parameters USB Device Type HID Keyboard Emulation 7-7 USB Country Keyboard Types (Country Codes) North American 7-8 USB Keystroke Delay No Delay (0 msec) 7-10 USB CAPS Lock Override Disable 7-11 USB Ignore Unknown Characters Enable 7-12 Emulate Keypad Disable 7-13 USB Keyboard FN1 Substitution Disable 7-14 Function Key Mapping Disable 7-14 Simulated Caps Lock Disable 7-15 Convert Case No Case Conversion 7-15 USB Interface USB Host Parameters USB Device Type Select the desired USB device type. When changing USB Device Types, the scanner automatically resets. The scanner issues the standard startup beep sequences. *HID Keyboard Emulation IBM Table Top USB IBM Hand-Held USB 7-7 7-8 WLS 8400 Product Reference Guide USB Country Keyboard Types (Country Codes) Scan the bar code corresponding to the keyboard type. This setting applies only to the USB HID Keyboard Emulation device. When changing USB Country Keyboard Types, the scanner automatically resets. The scanner issues the standard startup beep sequences. *North American Standard USB Keyboard German Windows French Windows French Canadian Windows 95/98 USB Interface USB Country Keyboard Types (Country Codes) (continued) French Canadian Windows 2000/XP Spanish Windows Italian Windows Swedish Windows UK English Windows 7-9 7-10 WLS 8400 Product Reference Guide USB Country Keyboard Types (Country Codes) (continued) Japanese Windows (ASCII) Brazilian-Portuguese Windows USB Keystroke Delay This parameter sets the delay, in milliseconds, between emulated keystrokes. Scan a bar code below to increase the delay when hosts require a slower transmission of data. *No Delay (0 msec) Medium Delay (20 msec) Long Delay (40 msec) USB Interface USB CAPS Lock Override This option applies only to the HID Keyboard Emulation device. When enabled, the case of the data is preserved regardless of the state of the caps lock key. This setting is always enabled for the “Japanese, Windows (ASCII)” keyboard type and can not be disabled. Override Caps Lock Key (Enable) *Do Not Override Caps Lock Key (Disable) 7-11 7-12 WLS 8400 Product Reference Guide USB Ignore Unknown Characters This option applies only to the HID Keyboard Emulation device and IBM device. Unknown characters are characters the host does not recognize. When “Send Bar Codes With Unknown Characters” is selected, all bar code data is sent except for unknown characters, and no error beeps sound. When “Do Not Send Bar Codes With Unknown Characters” is selected, bar codes containing at least one unknown character are not sent to the host, and an error beep sounds. *Send Bar Codes with Unknown Characters (Enable) Do Not Send Bar Codes with Unknown Characters (Disable) USB Interface Emulate Keypad When enabled, all characters are sent as ASCII sequences over the numeric keypad. For example ASCII A would be sent as “ALT make” 0 6 5 “ALT Break”. *Disable Keypad Emulation Enable Keypad Emulation 7-13 7-14 WLS 8400 Product Reference Guide USB Keyboard FN 1 Substitution This option applies only to the USB HID Keyboard Emulation device. When enabled, this allows replacement of any FN 1 characters in an EAN 128 bar code with a Key Category and value chosen by the user. See FN1 Substitution Values on page 9-9 to set the Key Category and Key Value. Enable USB Keyboard FN 1 Substitution *Disable USB Keyboard FN 1 Substitution Function Key Mapping ASCII values under 32 are normally sent as a control-key sequences (see Table 7-2 on page 7-16). When this parameter is enabled, the keys in bold are sent in place of the standard key mapping. Table entries that do not have a bold entry remain the same whether or not this parameter is enabled. *Disable Function Key Mapping Enable Function Key Mapping USB Interface Simulated Caps Lock When enabled, the scanner inverts upper and lower case characters on the scanner bar code as if the Caps Lock state is enabled on the keyboard. This inversion is done regardless of the current state of the keyboard’s Caps Lock state. *Disable Simulated Caps Lock Enable Simulated Caps Lock Convert Case When enabled, the scanner converts all bar code data to the selected case. *No Case Conversion Convert All to Upper Case Convert All to Lower Case 7-15 7-16 WLS 8400 Product Reference Guide ASCII Character Set Table 7-2. USB Prefix/Suffix Values Full ASCII Code 39 Encode Char.acter Prefix/ Suffix Value Keystroke 1000 %U CTRL 2 1001 $A CTRL A 1002 $B CTRL B 1003 $C CTRL C 1004 $D CTRL D 1005 $E CTRL E 1006 $F CTRL F 1007 $G CTRL G 1008 $H CTRL H/ BACKSPACE1 1009 $I CTRL I/ HORIZONTAL TAB1 1010 $J CTRL J 1011 $K CTRL K 1012 $L CTRL L 1013 $M CTRL M/ENTER1 1014 $N CTRL N 1015 $O CTRL O 1016 $P CTRL P 1017 $Q CTRL Q 1018 $R CTRL R 1019 $S CTRL S 1020 $T CTRL T 1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the unbolded keystroke is sent. USB Interface Table 7-2. USB Prefix/Suffix Values (Continued) Full ASCII Code 39 Encode Char.acter Prefix/ Suffix Value Keystroke 1021 $U CTRL U 1022 $V CTRL V 1023 $W CTRL W 1024 $X CTRL X 1025 $Y CTRL Y 1026 $Z CTRL Z 1027 %A CTRL [/ESC1 1028 %B CTRL \ 1029 %C CTRL ] 1030 %D CTRL 6 1031 %E CTRL - 1032 Space Space 1033 /A ! 1034 /B “ 1035 /C # 1036 /D $ 1037 /E % 1038 /F & 1039 /G ‘ 1040 /H ( 1041 /I ) 1042 /J * 1043 /K + 1044 /L , 1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the unbolded keystroke is sent. 7-17 7-18 WLS 8400 Product Reference Guide Table 7-2. USB Prefix/Suffix Values (Continued) Full ASCII Code 39 Encode Char.acter Prefix/ Suffix Value Keystroke 1045 - - 1046 . . 1047 /O / 1048 0 0 1049 1 1 1050 2 2 1051 3 3 1052 4 4 1053 5 5 1054 6 6 1055 7 7 1056 8 8 1057 9 9 1058 /Z : 1059 %F ; 1060 %G < 1061 %H = 1062 %I > 1063 %J ? 1064 %V @ 1065 A A 1066 B B 1067 C C 1068 D D 1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the unbolded keystroke is sent. USB Interface Table 7-2. USB Prefix/Suffix Values (Continued) Full ASCII Code 39 Encode Char.acter Prefix/ Suffix Value Keystroke 1069 E E 1070 F F 1071 G G 1072 H H 1073 I I 1074 J J 1075 K K 1076 L L 1077 M M 1078 N N 1079 O O 1080 P P 1081 Q Q 1082 R R 1083 S S 1084 T T 1085 U U 1086 V V 1087 W W 1088 X X 1089 Y Y 1090 Z Z 1091 %K [ 1092 %L \ 1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the unbolded keystroke is sent. 7-19 7-20 WLS 8400 Product Reference Guide Table 7-2. USB Prefix/Suffix Values (Continued) Full ASCII Code 39 Encode Char.acter Prefix/ Suffix Value Keystroke 1093 %M ] 1094 %N ^ 1095 %O _ 1096 %W ` 1097 +A a 1098 +B b 1099 +C c 1100 +D d 1101 +E e 1102 +F f 1103 +G g 1104 +H h 1105 +I i 1106 +J j 1107 +K k 1108 +L l 1109 +M m 1110 +N n 1111 +O o 1112 +P p 1113 +Q q 1114 +R r 1115 +S s 1116 +T t 1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the unbolded keystroke is sent. USB Interface Table 7-2. USB Prefix/Suffix Values (Continued) Prefix/ Suffix Value Full ASCII Code 39 Encode Char.acter Keystroke 1117 +U u 1118 +V v 1119 +W w 1120 +X x 1121 +Y y 1122 +Z z 1123 %P { 1124 %Q | 1125 %R } 1126 %S ~ 1The keystroke in bold is sent only if the “Function Key Mapping” is enabled. Otherwise, the unbolded keystroke is sent. Table 7-3. USB ALT Key Character Set ALT Keys Keystroke 2064 ALT 2 2065 ALT A 2066 ALT B 2067 ALT C 2068 ALT D 2069 ALT E 2070 ALT F 2071 ALT G 2072 ALT H 7-21 7-22 WLS 8400 Product Reference Guide Table 7-3. USB ALT Key Character Set (Continued) ALT Keys Keystroke 2073 ALT I 2074 ALT J 2075 ALT K 2076 ALT L 2077 ALT M 2078 ALT N 2079 ALT O 2080 ALT P 2081 ALT Q 2082 ALT R 2083 ALT S 2084 ALT T 2085 ALT U 2086 ALT V 2087 ALT W 2088 ALT X 2089 ALT Y 2090 ALT Z Table 7-4. USB GUI Key Character Set GUI Key Keystroke 3000 Right Control Key 3048 GUI 0 Note: GUI Shift Keys - The Apple™ iMac keyboard has an apple key on either side of the space bar. Windows-based systems have a GUI key to the left of the left ALT key, and to the right of the right ALT key. USB Interface Table 7-4. USB GUI Key Character Set (Continued) GUI Key Keystroke 3049 GUI 1 3050 GUI 2 3051 GUI 3 3052 GUI 4 3053 GUI 5 3054 GUI 6 3055 GUI 7 3056 GUI 8 3057 GUI 9 3065 GUI A 3066 GUI B 3067 GUI C 3068 GUI D 3069 GUI E 3070 GUI F 3071 GUI G 3072 GUI H 3073 GUI I 3074 GUI J 3075 GUI K 3076 GUI L 3077 GUI M 3078 GUI N 3079 GUI O Note: GUI Shift Keys - The Apple™ iMac keyboard has an apple key on either side of the space bar. Windows-based systems have a GUI key to the left of the left ALT key, and to the right of the right ALT key. 7-23 7-24 WLS 8400 Product Reference Guide Table 7-4. USB GUI Key Character Set (Continued) GUI Key Keystroke 3080 GUI P 3081 GUI Q 3082 GUI R 3083 GUI S 3084 GUI T 3085 GUI U 3086 GUI V 3087 GUI W 3088 GUI X 3089 GUI Y 3090 GUI Z Note: GUI Shift Keys - The Apple™ iMac keyboard has an apple key on either side of the space bar. Windows-based systems have a GUI key to the left of the left ALT key, and to the right of the right ALT key. Table 7-5. USB F Key Character Set F Keys Keystroke 5001 F1 5002 F2 5003 F3 5004 F4 5005 F5 5006 F6 5007 F7 5008 F8 5009 F9 USB Interface Table 7-5. USB F Key Character Set (Continued) F Keys Keystroke 5010 F10 5011 F11 5012 F 12 5013 F 13 5014 F 14 5015 F 15 5016 F16 5017 F 17 5018 F 18 5019 F 19 5020 F 20 5021 F 21 5022 F 22 5023 F 23 5024 F 24 Table 7-6. USB Numeric Keypad Character Set Numeric Keypad Keystroke 6042 * 6043 + 6044 undefined 6045 - 6046 . 6047 / 6048 0 7-25 7-26 WLS 8400 Product Reference Guide Table 7-6. USB Numeric Keypad Character Set (Continued) Numeric Keypad Keystroke 6049 1 6050 2 6051 3 6052 4 6053 5 6054 6 6055 7 6056 8 6057 9 6058 Enter 6059 Num Lock Table 7-7. USB Extended Keypad Character Set Extended Keypad Keystroke 7001 Break 7002 Delete 7003 PgUp 7004 End 7005 Pg Dn 7006 Pause 7007 Scroll Lock 7008 Backspace 7009 Tab 7010 Print Screen 7011 Insert USB Interface Table 7-7. USB Extended Keypad Character Set (Continued) Extended Keypad Keystroke 7012 Home 7013 Enter 7014 Escape 7015 Up Arrow 7016 Down Arrow 7017 Left Arrow 7018 Right Arrow 7-27 7-28 WLS 8400 Product Reference Guide 8 Symbologies Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5 Scanning Sequence Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5 Errors While Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5 Symbology Default Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6 UPC/EAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-10 Enable/Disable UPC-A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-10 Enable/Disable UPC-E. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-10 Enable/Disable UPC-E1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-11 Enable/Disable EAN-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-11 Enable/Disable EAN-8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-12 Enable/Disable Bookland EAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-12 Decode UPC/EAN/JAN Supplementals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13 UPC/EAN/JAN Supplemental Redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-15 Transmit UPC-A/UPC-E/UPC-E1 Check Digit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-15 UPC-A Preamble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-17 UPC-E Preamble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-18 8-2 WLS 8400 Product Reference Guide UPC-E1 Preamble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Convert UPC-E to UPC-A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Convert UPC-E1 to UPC-A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EAN-8/JAN-8 Extend . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Code 128. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enable/Disable Code 128 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enable/Disable UCC/EAN-128. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enable/Disable ISBT 128 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Code 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enable/Disable Code 39 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enable/Disable Trioptic Code 39 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Convert Code 39 to Code 32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Code 32 Prefix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set Lengths for Code 39 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Code 39 Check Digit Verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transmit Code 39 Check Digit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Code 39 Full ASCII Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Code 93. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enable/Disable Code 93 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set Lengths for Code 93 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Code 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Code 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set Lengths for Code 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Code 11 Check Digit Verification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transmit Code 11 Check Digits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Interleaved 2 of 5 (I 2 of 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enable/Disable Interleaved 2 of 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set Lengths for Interleaved 2 of 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I 2 of 5 Check Digit Verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transmit I 2 of 5 Check Digit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Convert I 2 of 5 to EAN-13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Discrete 2 of 5 (D 2 of 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enable/Disable Discrete 2 of 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Set Lengths for Discrete 2 of 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Codabar (NW - 7). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Enable/Disable Codabar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-19 12-20 12-21 12-22 12-22 12-22 12-23 12-23 12-24 12-24 12-24 12-25 12-26 12-27 12-29 12-30 12-31 12-32 12-32 12-32 12-34 12-34 12-34 12-36 12-37 12-38 12-38 12-38 12-41 12-42 12-42 12-43 12-43 12-43 12-45 12-45 Symbologies Set Lengths for Codabar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-46 CLSI Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-48 NOTIS Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-48 MSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-49 Enable/Disable MSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-49 Set Lengths for MSI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-49 MSI Check Digits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-51 Transmit MSI Check Digit(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-52 MSI Check Digit Algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-52 RSS (Reduced Space Symbology) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-53 RSS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-53 RSS Limited . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-53 Convert RSS to UPC/EAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-54 Redundancy Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-55 Redundancy Level 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-55 Redundancy Level 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-55 Redundancy Level 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-56 Redundancy Level 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-56 Security Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-57 Security Level 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-57 Security Level 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-57 Security Level 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-58 Security Level 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-58 Bi-directional Redundancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-59 8-3 8-4 WLS 8400 Product Reference Guide Symbologies Introduction This chapter describes all symbology features and provides the programming bar codes necessary for selecting these features for the scanner. Before programming, follow the instructions in Chapter 1, Getting Started. The scanner is shipped with the settings shown in the Symbology Default Table on page 86 (also see Chapter A, Standard Default Parameters for all host device and miscellaneous scanner defaults). If the default values suit the requirements, programming may not be necessary. Features values are set by scanning single bar codes or short bar code sequences. To return all features to their default values, scan the Set All Defaults bar code on page 4-5. If the USB cable is not being used, a host type must be selected. See each host chapter for specific host information. Scanning Sequence Examples In most cases, only one bar code needs to be scanned to set a specific parameter value. For example, to transmit bar code data without the UPC-A check digit, scan the Do Not Transmit UPC-A Check Digit bar code listed under Transmit UPC-A/UPC-E/UPC-E1 Check Digit on page 8-15. The scanner issues a fast warble beep and the LED turns green, signifying a successful parameter entry. Other parameters, such as Set Length(s) for D 2 of 5 require that several bar codes be scanned in the proper sequence. See the individual parameter, like Set Length(s) for D 2 of 5, for this procedure. Errors While Scanning Unless otherwise specified, if an error is made during a scanning sequence, just re-scan the correct parameter. 8-5 8-6 WLS 8400 Product Reference Guide Symbology Default Parameters Table 8-1 lists the defaults for all symbologies parameters. To change any option, scan the appropriate bar code(s) provided in the Symbologies Parameters section beginning on 8-10. See Chapter A, Standard Default Parameters for all user preferences, hosts, symbologies, and miscellaneous default parameters. Table 8-1. Symbology Default Table Parameter Default Page Number UPC/EAN UPC-A Enable 8-10 UPC-E Enable 8-10 UPC-E1 Disable 8-11 EAN-13/JAN 13 Enable 8-11 EAN-8/JAN 8 Enable 8-12 Bookland EAN Disable 8-12 Decode UPC/EAN/JAN Supplementals (2 and 5 digits) Ignore Supplementals 8-14 UPC/EAN/JAN Supplemental Redundancy 14 8-15 Transmit UPC-A Check Digit Enable 8-15 Transmit UPC-E Check Digit Enable 8-16 Transmit UPC-E1 Check Digit Enable 8-16 UPC-A Preamble System Character 8-17 UPC-E Preamble System Character 8-18 UPC-E1 Preamble System Character 8-19 Convert UPC-E to A Disable 8-20 Symbologies Table 8-1. Symbology Default Table (Continued) Parameter Default Page Number Convert UPC-E1 to A Disable 8-21 EAN-8/JAN-8 Extend Disable 8-22 Code 128 Enable 8-22 UCC/EAN-128 Enable 8-23 ISBT 128 Enable 8-23 Code 39 Enable 8-24 Trioptic Code 39 Disable 8-24 Convert Code 39 to Code 32 Disable 8-25 Code 32 Prefix Disable 8-26 Set Length(s) for Code 39 2 to 55 8-27 Code 39 Check Digit Verification Disable 8-29 Transmit Code 39 Check Digit Disable 8-30 Code 39 Full ASCII Conversion Disable 8-31 Code 93 Disable 8-32 Set Lengths for Code 93 4 to 55 8-32 Code 11 Disable 8-34 Set Lengths for Code 11 4 to 41 8-34 Code 128 Code 39 Code 93 Code 11 8-7 8-8 WLS 8400 Product Reference Guide Table 8-1. Symbology Default Table (Continued) Parameter Default Page Number Code 11 Check Digit Verification One Check Digit 8-36 Transmit Code 11 Check Digits Disable 8-37 Interleaved 2 of 5 (I 2 of 5) Enable 8-38 Set Lengths for Interleaved 2 of 5 14 8-38 I 2 of 5 Check Digit Verification Disable 8-41 Transmit I 2 of 5 Check Digit Disable 8-42 Convert I 2 of 5 to EAN-13 Disable 8-43 Discrete 2 of 5 Disable 8-44 Set Lengths for D 2 of 5 12 8-44 Codabar Disable 8-46 Set Lengths for Codabar 5 to 55 8-47 CLSI Editing Disable 8-49 NOTIS Editing Disable 8-49 MSI Disable 8-50 Set Lengths for MSI 6 to 55 8-50 MSI Check Digits One 8-52 Transmit MSI Check Digit(s) Disable 8-53 Interleaved 2 of 5 (I 2 of 5) Discrete 2 of 5 (D 2 of 5) Codabar (NW - 7) MSI Symbologies Table 8-1. Symbology Default Table (Continued) Parameter MSI Check Digit Algorithm Default Page Number Mod 10/Mod 10 8-53 RSS 14 Disable 8-54 RSS Limited Disable 8-54 RSS Expanded Disable 8-55 Convert RSS to UPC/EAN Disable 8-55 Redundancy Level 1 8-56 Security Levels 0 8-58 Bi-directional Redundancy Disable 8-60 RSS (Reduced Space Symbology) Symbology - Specific Security Levels 8-9 8-10 WLS 8400 Product Reference Guide UPC/EAN Enable/Disable UPC-A To enable or disable UPC-A, scan the appropriate bar code below. *Enable UPC-A Disable UPC-A Enable/Disable UPC-E To enable or disable UPC-E, scan the appropriate bar code below. *Enable UPC-E Disable UPC-E Symbologies Enable/Disable UPC-E1 UPC-E1 is disabled by default. To enable or disable UPC-E1, scan the appropriate bar code below. UPC-E1 is not a UCC (Uniform Code Council) approved symbology. Enable UPC-E1 *Disable UPC-E1 Enable/Disable EAN-13 To enable or disable EAN-13, scan the appropriate bar code below. *Enable EAN-13/JAN-13 Disable EAN-13/JAN-13 8-11 8-12 WLS 8400 Product Reference Guide Enable/Disable EAN-8 To enable or disable EAN-8, scan the appropriate bar code below. *Enable EAN-8/JAN-8 Disable EAN-8/JAN-8 Enable/Disable Bookland EAN To enable or disable Bookland EAN, scan the appropriate bar code below. Enable Bookland EAN *Disable Bookland EAN Symbologies Decode UPC/EAN/JAN Supplementals Supplementals are bar codes appended according to specific format conventions (e.g., UPC A+2, UPC E+2, EAN 13+2). Six options are available. • • • • • • If Decode UPC/EAN Only With Supplementals is selected, UPC/EAN symbols without supplementals are not decoded. If Ignore Supplementals is selected, and the scanner is presented with a UPC/EAN with a supplemental, the UPC/EAN is decoded and the supplemental bar code is ignored. An Autodiscriminate Option is also available. If this option is selected, choose an appropriate UPC/EAN/JAN Supplemental Redundancy value from the next page. A value of 14 or more is recommended. Enable 378/379 Supplemental Mode to enable only EAN13 bar codes starting with a ‘378’ or ‘379’ prefix to be delayed by the supplemental search process. All other UPC/EAN bar codes are exempted from the search and are reported instantly upon their decode. Select Enable 978 Supplemental Mode to enable only EAN13 bar codes starting with a ‘978’ prefix to be delayed by the supplemental search process. All other UPC/EAN bar codes are exempted from the search and are reported instantly upon their decode. Select Enable Smart Supplemental Mode to enable only EAN13 bar codes starting with a ‘378’, ‘379’, or ‘978’ prefix to be delayed by the supplemental search process. All other UPC/EAN bar codes are exempted from the search and are reported instantly upon their decode. In order to minimize the risk of invalid data transmission, it is recommended to select either to decode or ignore supplemental characters. Decode UPC/EAN/JAN Only With Supplementals 8-13 8-14 WLS 8400 Product Reference Guide Decode UPC/EAN/JAN Supplementals (continued) *Ignore Supplementals Autodiscriminate UPC/EAN/JAN Supplementals Enable 378/379 Supplemental Mode Enable 978 Supplemental Mode Enable Smart Supplemental Mode Symbologies UPC/EAN/JAN Supplemental Redundancy With Autodiscriminate UPC/EAN/JAN Supplementals selected, this option adjusts the number of times a symbol without supplementals is decoded before transmission. The range is from two to thirty times. 14 or above is recommended when decoding a mix of UPC/EAN symbols with and without supplementals, and the autodiscriminate option is selected. The default is set at 14. Scan the bar code below to set a decode redundancy value. Next, scan two numeric bar codes beginning on page D-3 in Chapter D, Numeric Bar Codes. Single digit numbers must have a leading zero. In case of an error, or to change the selection, scan Cancel on page D-7. UPC/EAN/JAN Supplemental Redundancy Transmit UPC-A/UPC-E/UPC-E1 Check Digit The check digit is the last character of the symbol used to verify the integrity of the data. Scan the appropriate bar code below to transmit the bar code data with or without the UPCA, UPC-E or UPC-E1 check digit. It is always verified to guarantee the integrity of the data. UPC-A Check Digit *Transmit UPC-A Check Digit Do Not Transmit UPC-A Check Digit 8-15 8-16 WLS 8400 Product Reference Guide UPC-E Check Digit *Transmit UPC-E Check Digit Do Not Transmit UPC-E Check Digit UPC-E1 Check Digit *Transmit UPC-E1 Check Digit Do Not Transmit UPC-E1 Check Digit Symbologies UPC-A Preamble Preamble characters are part of the UPC symbol consisting of Country Code and System Character. Three options are given for transmitting UPC-A preamble to the host device: transmit System Character only, transmit System Character and Country Code (“0” for USA), and no preamble transmitted. Select the appropriate option to match the host system. No Preamble () *System Character ( ) System Character & Country Code (< COUNTRY CODE> ) 8-17 8-18 WLS 8400 Product Reference Guide UPC-E Preamble Preamble characters are part of the UPC symbol consisting of Country Code and System Character. Three options are given for transmitting UPC-E preamble to the host device: transmit System Character only, transmit System Character and Country Code (“0” for USA), and no preamble transmitted. Select the appropriate option to match the host system. No Preamble () *System Character ( ) System Character & Country Code (< COUNTRY CODE> ) Symbologies UPC-E1 Preamble Preamble characters are part of the UPC symbol consisting of Country Code and System Character. Three options are given for transmitting UPC-E1 preamble to the host device: transmit System Character only, transmit System Character and Country Code (“0” for USA), and no preamble transmitted. Select the appropriate option to match the host system. No Preamble () *System Character ( ) System Character & Country Code (< COUNTRY CODE> ) 8-19 8-20 WLS 8400 Product Reference Guide Convert UPC-E to UPC-A When enabled, UPC-E (zero suppressed) decoded data is converted to UPC-A format before transmission. After conversion, the data follows UPC-A format and is affected by UPC-A programming selections (e.g., Preamble, Check Digit). When disabled, UPC-E decoded data is transmitted as UPC-E data, without conversion. Convert UPC-E to UPC-A (Enable) *Do Not Convert UPC-E to UPC-A (Disable) Symbologies Convert UPC-E1 to UPC-A When enabled, UPC-E1 decoded data is converted to UPC-A format before transmission. After conversion, the data follows UPC-A format and is affected by UPC-A programming selections (e.g., Preamble, Check Digit). When disabled, UPC-E1 decoded data is transmitted as UPC-E1 data, without conversion. Convert UPC-E1 to UPC-A (Enable) *Do Not Convert UPC-E1 to UPC-A (Disable) 8-21 8-22 WLS 8400 Product Reference Guide EAN-8/JAN-8 Extend When enabled, this parameter adds five leading zeros to decoded EAN-8 symbols to make them compatible in format to EAN-13 symbols. When disabled, EAN-8 symbols are transmitted as is. Enable EAN/JAN Zero Extend *Disable EAN/JAN Zero Extend Code 128 Enable/Disable Code 128 To enable or disable Code 128, scan the appropriate bar code below. *Enable Code 128 Disable Code 128 Symbologies Enable/Disable UCC/EAN-128 To enable or disable UCC/EAN-128, scan the appropriate bar code below. *Enable UCC/EAN-128 Disable UCC/EAN-128 Enable/Disable ISBT 128 To enable or disable ISBT 128, scan the appropriate bar code below. *Enable ISBT 128 Disable ISBT 128 8-23 8-24 WLS 8400 Product Reference Guide Code 39 Enable/Disable Code 39 To enable or disable Code 39, scan the appropriate bar code below. *Enable Code 39 Disable Code 39 Enable/Disable Trioptic Code 39 Trioptic Code 39 is a variant of Code 39 used in the marking of computer tape cartridges. Trioptic Code 39 symbols always contain six characters. To enable or disable Trioptic Code 39, scan the appropriate bar code below. Enable Trioptic Code 39 *Disable Trioptic Code 39 Trioptic Code 39 and Code 39 Full ASCII cannot be enabled simultaneously. Symbologies Convert Code 39 to Code 32 Code 32 is a variant of Code 39 used by the Italian pharmaceutical industry. Scan the appropriate bar code below to enable or disable converting Code 39 to Code 32. Code 39 must be enabled in order for this parameter to function. Convert Code 39 to Code 32 (Enable) *Do Not Convert Code 39 to Code 32 (Disable) 8-25 8-26 WLS 8400 Product Reference Guide Code 32 Prefix Scan the appropriate bar code below to enable or disable adding the prefix character “A” to all Code 32 bar codes. Convert Code 39 to Code 32 must be enabled for this parameter to function. Enable Code 32 Prefix *Disable Code 32 Prefix Symbologies Set Lengths for Code 39 The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for Code 39 may be set for any length, one or two discrete lengths, or lengths within a specific range. If Code 39 Full ASCII is enabled, Length Within a Range or Any Length are the preferred options. When setting lengths for different bar code types by scanning single digit numbers, single digit numbers must always be preceded by a leading zero. One Discrete Length - This option allows the scanner to decode only those Code 39 symbols containing a selected length. Lengths are selected from the numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode only Code 39 symbols with 14 characters, scan Code 39 - One Discrete Length, then scan 1 followed by 4. In case of an error, or to change the selection, scan Cancel on page D-7. Code 39 - One Discrete Length Two Discrete Lengths - This option allows the scanner to decode only those Code 39 symbols containing either of two selected lengths. Lengths are selected from the numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode only those Code 39 symbols containing either 2 or 14 characters, select Code 39 Two Discrete Lengths, then scan 0, 2, 1, and then 4. In case of an error, or to change the selection, scan Cancel on page D-7. Code 39 - Two Discrete Lengths 8-27 8-28 WLS 8400 Product Reference Guide Length Within Range - This option allows the scanner to decode a Code 39 symbol with a specific length range. The length range is selected from numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode Code 39 symbols containing between 4 and 12 characters, first scan Code 39 - Length Within Range. Then scan 0, 4, 1, and 2 (single digit numbers must always be preceded by a leading zero). In case of an error, or to change the selection, scan Cancel on page D-7. Code 39 - Length Within Range Any Length - This option allows the scanner to decode Code 39 symbols containing any number of characters within the scanner capability. Code 39 - Any Length Symbologies Code 39 Check Digit Verification When this feature is enabled, the scanner checks the integrity of all Code 39 symbols to verify that the data complies with specified check digit algorithm. Only those Code 39 symbols which include a modulo 43 check digit are decoded when this feature is enabled. This feature should only be enabled if the code 39 symbols contain a Modulo 43 check digit. Enable Code 39 Check Digit *Disable Code 39 Check Digit 8-29 8-30 WLS 8400 Product Reference Guide Transmit Code 39 Check Digit Scan a bar code below to transmit Code 39 data with or without the check digit. Transmit Code 39 Check Digit (Enable) *Do Not Transmit Code 39 Check Digit (Disable) Code 39 Check Digit Verification must be enabled for this parameter to function. Symbologies Code 39 Full ASCII Conversion Code 39 Full ASCII is a variant of Code 39 which pairs characters to encode the full ASCII character set. To enable or disable Code 39 Full ASCII, scan the appropriate bar code below. See Table 5-2 on page 5-19 and for the mapping of Code 39 characters to ASCII values. Enable Code 39 Full ASCII *Disable Code 39 Full ASCII Trioptic Code 39 and Code 39 Full ASCII cannot be enabled simultaneously. Code 39 Full ASCII to Full ASCII Correlation is host-dependent, and is therefore described in the "ASCII Character Set" Table for the appropriate interface. The Wedge Host conversion table can be found on 5-5, USB Host conversion table can be found on 7-6, and RS-232 Host conversion table can be found on 6-5. 8-31 8-32 WLS 8400 Product Reference Guide Code 93 Enable/Disable Code 93 To enable or disable Code 93, scan the appropriate bar code below. Enable Code 93 *Disable Code 93 Set Lengths for Code 93 The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for Code 93 may be set for any length, one or two discrete lengths, or lengths within a specific range. One Discrete Length - This option allows scanner to decode only those Code 93 symbols containing a selected length. Lengths are selected from the numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode only Code 93 symbols with 14 characters, scan Code 93 - One Discrete Length, then scan 1 followed by 4. In case of an error, or to change the selection, scan Cancel on page D-7. Code 93 - One Discrete Length Symbologies Set Lengths for Code 93 (continued) Two Discrete Lengths - This option allows the scanner to decode only those Code 93 symbols containing either of two selected lengths. Lengths are selected from the numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode only those Code 93 symbols containing either 2 or 14 characters, select Code 93 Two Discrete Lengths, then scan 0, 2, 1, and then 4. In case of an error, or to change the selection, scan Cancel on page D-7. Code 93 - Two Discrete Lengths Length Within Range - This option allows the scanner to decode a Code 93 symbol with a specific length range. The length range is selected from numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode Code 93 symbols containing between 4 and 12 characters, first scan Code 93 - Length Within Range. Then scan 0, 4, 1, and 2 (single digit numbers must always be preceded by a leading zero). In case of an error, or to change the selection, scan Cancel on page D-7. Code 93 - Length Within Range Any Length - This option allows the scanner to decode Code 93 symbols containing any number of characters within the scanner’s capability. Code 93 - Any Length 8-33 8-34 WLS 8400 Product Reference Guide Code 11 Code 11 To enable or disable Code 11, scan the appropriate bar code below. Enable Code 11 *Disable Code 11 Set Lengths for Code 11 The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for Code 11 may be set for any length, one or two discrete lengths, or lengths within a specific range. One Discrete Length - This option allows the scanner to decode only those Code 11 symbols containing a selected length. Lengths are selected from the numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode only Code 11 symbols with 14 characters, scan Code 11 - One Discrete Length, then scan 1 followed by 4. In case of an error, or to change the selection, scan Cancel on page D-7. Code 11 - One Discrete Length Symbologies Set Lengths for Code 11 (continued) Two Discrete Lengths - This option allows the scanner to decode only those Code 11 symbols containing either of two selected lengths. Lengths are selected from the numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode only those Code 11 symbols containing either 2 or 14 characters, select Code 11 Two Discrete Lengths, then scan 0, 2, 1, and then 4. In case of an error, or to change the selection, scan Cancel on page D-7. Code 11 - Two Discrete Lengths Length Within Range - This option allows the scanner to decode a Code 11 symbol with a specific length range. The length range is selected from numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode Code 11 symbols containing between 4 and 12 characters, first scan Code 11 - Length Within Range. Then scan 0, 4, 1, and 2 (single digit numbers must always be preceded by a leading zero). In case of an error, or to change the selection, scan Cancel on page D-7. Code 11 - Length Within Range Any Length - This option allows the scanner to decode Code 11 symbols containing any number of characters within the scanner capability. Code 11 - Any Length 8-35 8-36 WLS 8400 Product Reference Guide Code 11 Check Digit Verification This feature allows the scanner to check the integrity of all Code 11 symbols to verify that the data complies with the specified check digit algorithm. This selects the check digit mechanism for the decoded Code 11 bar code. The options are to check for one check digit, check for two check digits, or disable the feature. To enable this feature, scan the bar code below corresponding to the number of check digits encoded in the Code 11 symbols. Disable *One Check Digit Two Check Digits Symbologies Transmit Code 11 Check Digits This feature selects whether or not to transmit the Code 11 check digit(s). Transmit Code 11 Check Digit(s) (Enable) *Do Not Transmit Code 11 Check Digit(s) (Disable) Code 11 Check Digit Verification must be enabled for this parameter to function. 8-37 8-38 WLS 8400 Product Reference Guide Interleaved 2 of 5 (I 2 of 5) Enable/Disable Interleaved 2 of 5 To enable or disable Interleaved 2 of 5, scan the appropriate bar code below, and select an Interleaved 2 of 5 length from the following pages. *Enable Interleaved 2 of 5 Disable Interleaved 2 of 5 Set Lengths for Interleaved 2 of 5 The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for I 2 of 5 may be set for any length, one or two discrete lengths, or lengths within a specific range. One Discrete Length - This option allows the scanner to decode only those I 2 of 5 symbols containing a selected length. Lengths are selected from the numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode only I 2 of 5 symbols with 14 characters, scan I 2 of 5 - One Discrete Length, then scan 1 followed by 4. In case of an error, or to change the selection, scan Cancel on page D-7. I 2 of 5 - One Discrete Length Symbologies Set Lengths for Interleaved 2 of 5 (continued) Two Discrete Lengths - This option allows the scanner to decode only those I 2 of 5 symbols containing either of two selected lengths. Lengths are selected from the numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode only those I 2 of 5 symbols containing either 2 or 14 characters, select I 2 of 5 Two Discrete Lengths, then scan 0, 2, 1, and then 4. In case of an error, or to change the selection, scan Cancel on page D-7. I 2 of 5 - Two Discrete Lengths Length Within Range - This option allows the scanner to decode an I 2 of 5 symbol with a specific length range. The length range is selected from numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode I 2 of 5 symbols containing between 4 and 12 characters, first scan I 2 of 5 - Length Within Range. Then scan 0, 4, 1, and 2 (single digit numbers must always be preceded by a leading zero). In case of an error, or to change the selection, scan Cancel on page D-7. I 2 of 5 - Length Within Range 8-39 8-40 WLS 8400 Product Reference Guide Set Lengths for Interleaved 2 of 5 (continued) Any Length - This option allows the scanner to decode I 2 of 5 symbols containing any number of characters within the scanner capability. Due to the construction of the I 2 of 5 symbology, it is possible for a scan line covering only a portion of the code to be interpreted as a complete scan, yielding less data than is actually encoded in the bar code. To prevent this from happening, it is recommended that specific lengths (I 2 of 5 - One Discrete Length - Two Discrete Lengths) be selected for I 2 of 5 applications. I 2 of 5 - Any Length Symbologies I 2 of 5 Check Digit Verification When this feature is enabled, the scanner checks the integrity of all I 2 of 5 symbols to verify the data complies with either the specified Uniform Symbology Specification (USS), or the Optical Product Code Council (OPCC) check digit algorithm. *Disable USS Check Digit OPCC Check Digit 8-41 8-42 WLS 8400 Product Reference Guide Transmit I 2 of 5 Check Digit Scan the appropriate bar code below to transmit I 2 of 5 data with or without the check digit. Transmit I 2 of 5 Check Digit (Enable) *Do Not Transmit I 2 of 5 Check Digit (Disable) Convert I 2 of 5 to EAN-13 This parameter converts a 14 character I 2 of 5 code into EAN-13, and transmits to the host as EAN-13. In order to accomplish this, the I 2 of 5 code must be enabled, and the code must have a leading zero and a valid EAN-13 check digit. Scanning a single bar code below, Convert I 2 of 5 to EAN-13 (Enable), accomplishes this function. Convert I 2 of 5 to EAN-13 (Enable) Symbologies *Do Not Convert I 2 of 5 to EAN-13 (Disable) 8-43 8-44 WLS 8400 Product Reference Guide Discrete 2 of 5 (D 2 of 5) Enable/Disable Discrete 2 of 5 To enable or disable Discrete 2 of 5, scan the appropriate bar code below. Enable Discrete 2 of 5 *Disable Discrete 2 of 5 Set Lengths for Discrete 2 of 5 The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for D 2 of 5 may be set for any length, one or two discrete lengths, or lengths within a specific range. One Discrete Length - This option allows the scanner to decode only those D 2 of 5 symbols containing a selected length. Lengths are selected from the numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode only D 2 of 5 symbols with 14 characters, scan D 2 of 5 - One Discrete Length, then scan 1 followed by 4. In case of an error, or to change the selection, scan Cancel on page D-7. D 2 of 5 - One Discrete Length Symbologies Set Lengths for Discrete 2 of 5 (continued) Two Discrete Lengths - This option allows the scanner to decode only those D 2 of 5 symbols containing either of two selected lengths. Lengths are selected from the numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode only those D 2 of 5 symbols containing either 2 or 14 characters, select D 2 of 5 Two Discrete Lengths, then scan 0, 2, 1, and then 4. In case of an error, or to change the selection, scan Cancel on page D-7. D 2 of 5 - Two Discrete Lengths Length Within Range - This option allows the scanner to decode an D 2 of 5 symbol with a specific length range. The length range is selected from numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode D 2 of 5 symbols containing between 4 and 12 characters, first scan D 2 of 5 - Length Within Range. Then scan 0, 4, 1, and 2 (single digit numbers must always be preceded by a leading zero). In case of an error, or to change the selection, scan Cancel on page D-7. D 2 of 5 - Length Within Range 8-45 8-46 WLS 8400 Product Reference Guide Set Lengths for Discrete 2 of 5 (continued) Any Length - This option allows the scanner to decode D 2 of 5 symbols containing any number of characters within the scanner capability. Due to the construction of the D 2 of 5 symbology, it is possible for a scan line covering only a portion of the code to be interpreted as a complete scan, yielding less data than is actually encoded in the bar code. To prevent this from happening, it is recommended that specific lengths (D 2 of 5 - One Discrete Length - Two Discrete Lengths) be selected for D 2 of 5 applications. D 2 of 5 - Any Length Codabar (NW - 7) Enable/Disable Codabar To enable or disable Codabar, scan the appropriate bar code below. Enable Codabar *Disable Codabar Symbologies Set Lengths for Codabar The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for Codabar may be set for any length, one or two discrete lengths, or lengths within a specific range. One Discrete Length - This option allows the scanner to decode only those Codabar symbols containing a selected length. Lengths are selected from the numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode only Codabar symbols with 14 characters, scan Codabar - One Discrete Length, then scan 1 followed by 4. In case of an error, or to change the selection, scan Cancel on page D-7. Codabar - One Discrete Length Two Discrete Lengths - This option allows the scanner to decode only those Codabar symbols containing either of two selected lengths. Lengths are selected from the numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode only those Codabar symbols containing either 2 or 14 characters, select Codabar Two Discrete Lengths, then scan 0, 2, 1, and then 4. In case of an error, or to change the selection, scan Cancel on page D-7. Codabar - Two Discrete Lengths 8-47 8-48 WLS 8400 Product Reference Guide Set Lengths for Codabar (continued) Length Within Range - This option allows the scanner to decode a Codabar symbol with a specific length range. The length range is selected from numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode Codabar symbols containing between 4 and 12 characters, first scan Codabar - Length Within Range. Then scan 0, 4, 1, and 2 (single digit numbers must always be preceded by a leading zero). In case of an error, or to change the selection, scan Cancel on page D-7. Codabar - Length Within Range Any Length - This option allows the scanner to decode Codabar symbols containing any number of characters within the scanner capability. Codabar - Any Length Symbologies CLSI Editing When enabled, this parameter strips the start and stop characters and inserts a space after the first, fifth, and tenth characters of a 14-character Codabar symbol. Enable this feature if the host system requires this data format. Symbol length does not include start and stop characters. Enable CLSI Editing *Disable CLSI Editing NOTIS Editing When enabled, this parameter strips the start and stop characters from a decoded Codabar symbol. Enable this feature if the host system requires this data format. Enable NOTIS Editing *Disable NOTIS Editing 8-49 8-50 WLS 8400 Product Reference Guide MSI Enable/Disable MSI To enable or disable MSI, scan the appropriate bar code below. Enable MSI *Disable MSI Set Lengths for MSI The length of a code refers to the number of characters (i.e., human readable characters), including check digit(s) the code contains. Lengths for MSI may be set for any length, one or two discrete lengths, or lengths within a specific range. One Discrete Length - This option allows the scanner to decode only those MSI symbols containing a selected length. Lengths are selected from the numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode only MSI symbols with 14 characters, scan MSI - One Discrete Length, then scan 1 followed by 4. In case of an error, or to change the selection, scan Cancel on page D-7. MSI - One Discrete Length Symbologies Set Lengths for MSI (continued) Two Discrete Lengths - This option allows the scanner to decode only those MSI symbols containing either of two selected lengths. Lengths are selected from the numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode only those MSI symbols containing either 2 or 14 characters, select MSI - Two Discrete Lengths, then scan 0, 2, 1, and then 4. In case of an error, or to change the selection, scan Cancel on page D-7. MSI - Two Discrete Lengths Length Within Range - This option allows the scanner to decode an MSI symbol with a specific length range. The length range is selected from numeric bar codes beginning on page D-1 in Chapter D, Numeric Bar Codes. For example, to decode MSI symbols containing between 4 and 12 characters, first scan MSI - Length Within Range. Then scan 0, 4, 1, and 2 (single digit numbers must always be preceded by a leading zero). In case of an error, or to change the selection, scan Cancel on page D-7. MSI - Length Within Range 8-51 8-52 WLS 8400 Product Reference Guide Set Lengths for MSI (continued) Any Length - This option allows the scanner to decode MSI symbols containing any number of characters within the scanner capability. Due to the construction of the MSI symbology, it is possible for a scan line covering only a portion of the code to be interpreted as a complete scan, yielding less data than is actually encoded in the bar code. To prevent this from happening, it is recommended that specific lengths (MSI - One Discrete Length - Two Discrete Lengths) be selected for MSI applications. MSI - Any Length MSI Check Digits With MSI symbols, one check digit is mandatory and always verified by the reader. The second check digit is optional. If the MSI codes include two check digits, enable the verification of the second check digit by scanning the bar code below. See MSI Check Digit Algorithm on page 8-53 for the selection of second digit algorithms. *One MSI Check Digit Two MSI Check Digits Symbologies Transmit MSI Check Digit(s) Scan a bar code below to transmit MSI data with or without the check digit. Transmit MSI Check Digit(s) (Enable) *Do Not Transmit MSI Check Digit(s) (Disable) MSI Check Digit Algorithm Two algorithms are possible for the verification of the second MSI check digit. Select the bar code below corresponding to the algorithm used to encode the check digit. MOD 10/MOD 11 *MOD 10/MOD 10 8-53 8-54 WLS 8400 Product Reference Guide RSS (Reduced Space Symbology) RSS The variants of RSS are RSS 14, RSS Expanded, and RSS Limited. The limited and expanded versions have stacked variants. Scan the appropriate bar code below to enable or disable each variant of RSS. RSS 14 Enable RSS 14 *Disable RSS 14 RSS Limited Enable RSS Limited *Disable RSS Limited Symbologies RSS Expanded Enable RSS Expanded *Disable RSS Expanded Convert RSS to UPC/EAN This parameter only applies to RSS-14 and RSS Limited symbols not decoded as part of a Composite symbol. When this conversion is enabled, RSS-14 and RSS Limited symbols encoding a single zero as the first digit have the leading '010' stripped and the bar code reported as EAN-13. Bar codes beginning with two or more zeros but not six zeros have the leading '0100' stripped and the bar code reported as UPC-A. The UPC-A Preamble parameter to transmit the system character and country code applies to converted bar codes. Note that neither the system character nor the check digit can be stripped. Enable Convert RSS to UPC/EAN *Disable Convert RSS to UPC/EAN 8-55 8-56 WLS 8400 Product Reference Guide Redundancy Level The scanner offers four levels of decode redundancy. Higher redundancy levels are selected for decreasing levels of bar code quality. As redundancy levels increase, the scanner’s aggressiveness decreases. Select the redundancy level appropriate for the bar code quality. Redundancy Level 1 The following code types must be successfully read twice before being decoded: Code Type Code Length Codabar 8 characters or less MSI 4 characters or less D 2 of 5 8 characters or less I 2 of 5 8 characters or less *Redundancy Level 1 Redundancy Level 2 The following code types must be successfully read twice before being decoded: Code Type All Code Length All Redundancy Level 2 Symbologies Redundancy Level 3 Code types other than the following must be successfully read twice before being decoded. The following codes must be read three times: Code Type Code Length MSI Plessey 4 characters or less D 2 of 5 8 characters or less I 2 of 5 8 characters or less Codabar 8 characters or less Redundancy Level 3 Redundancy Level 4 The following code types must be successfully read three times before being decoded: Code Type All Code Length All Redundancy Level 4 8-57 8-58 WLS 8400 Product Reference Guide Security Level The scanner offers four levels of decode security for UPC/EAN bar codes. Increasing levels of security are provided for decreasing levels of bar code quality. There is an inverse relationship between security and scanner decode speed, so be sure to choose only that level of security necessary for any given application. Security Level 0 This is the default setting which allows the scanner to operate fastest, while providing sufficient security in decoding “in-spec” UPC/EAN bar codes. *Security Level 0 Security Level 1 As bar code quality levels diminish, certain characters become prone to misdecodes before others (i.e., 1, 2, 7, 8). If the scanner is misdecoding poorly printed bar codes, and the misdecodes are limited to these characters, select this security level. Security Level 1 Symbologies Security Level 2 If the scanner is misdecoding poorly printed bar codes, and the misdecodes are not limited to characters 1, 2, 7, and 8, select this security level. Security Level 2 Security Level 3 If Security Level 2 has been tried, and the scanner is still misdecoding, select this security level. Be advised, selecting this option is an extreme measure against misdecoding severely out of spec bar codes. Selection of this level of security may significantly impair the decoding ability of the scanner. If this level of security is necessary, try to improve the quality of the bar codes. Security Level 3 8-59 8-60 WLS 8400 Product Reference Guide Bi-Directional Redundancy Bi-directional redundancy is used for added security to linear code type security levels. When enabled, a bar code must be successfully scanned in both directions (forward and reverse) before reporting a good decode. Enable Bi-Directional Redundancy *Disable Bi-Directional Redundancy 9 Miscellaneous Scanner Options Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 Scanning Sequence Examples. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4 Errors While Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4 Miscellaneous Default Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-4 Miscellaneous Scanner Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5 Transmit Code ID Character . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5 Scan Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6 Prefix/Suffix Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6 Scan Data Transmission Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7 FN1 Substitution Values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9 Transmit “No Read” Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9 9-2 WLS 8400 Product Reference Guide Miscellaneous Scanner Options Introduction This chapter includes commonly used bar codes to customize how the data is transmitted to the host device. In addition to these bar codes for data formatting, see each host chapter for the appropriate host connections and host device features for the scanner. See Chapter 8, Symbologies and Chapter 10, Advanced Data Formatting for customizing data for transmission to the host device. Before programming, follow the instructions in Chapter 1, Getting Started. The scanner is shipped with the settings shown in the Miscellaneous Scanner Options Default Table on page 9-4 (also see Chapter A, Standard Default Parameters for all host device and miscellaneous scanner defaults). If the default values suit the requirements, programming may not be necessary. Features values are set by scanning single bar codes or short bar code sequences. 9-3 9-4 WLS 8400 Product Reference Guide Scanning Sequence Examples In most cases, only one bar code needs to be scanned to set a specific parameter value. Parameters, such as Prefix Value, require that several bar codes be scanned in the proper sequence. See each individual parameter for descriptions of this procedure. Errors While Scanning Unless otherwise specified, if an error is made during a scanning sequence, re-scan the correct parameter. Miscellaneous Default Parameters Table 9-1 lists the defaults for miscellaneous scanner options parameters. To change any option, scan the appropriate bar code(s) provided in the Miscellaneous Scanner Parameters section beginning on page 9-5. See Chapter A, Standard Default Parameters for all user preferences, hosts, symbologies, and miscellaneous default parameters. Table 9-1. Miscellaneous Scanner Options Default Table Parameter Default Page Number Miscellaneous Scanner Options Transmit Code ID Character None 9-5 Scan Angle Normal Angle 9-6 Prefix Value 7013 9-6 Suffix Value 7013 9-6 Scan Data Transmission Format Data As Is 9-7 FN1 Substitution Values Set FN1 Substitution Value 9-9 Transmit “No Read” Message Disable No Read 9-9 Miscellaneous Scanner Options Miscellaneous Scanner Parameters Transmit Code ID Character A Code ID character identifies the code type of a scanned bar code. This may be useful when the scanner is decoding more than one code type. In addition to any single character prefix already selected, the Code ID character is inserted between the prefix and the decoded symbol. The user may select no Code ID character, a Symbol Code ID character, or an AIM Code ID character. For Code ID Characters, see Symbol Code Identifiers on page B-3 and AIM Code Identifiers on page B-4. Symbol Code ID Character AIM Code ID Character *None 9-5 9-6 WLS 8400 Product Reference Guide Scan Angle The scanner supports two scan angles. This parameter provides two options for the length of the laser scanning beam. Use the bar codes below to change scan angles. *Normal Angle Alternate Angle Prefix/Suffix Values A prefix/suffix may be appended to scan data for use in data editing. These values are set by scanning a four-digit number (i.e., four bar codes) that corresponds to key codes for various terminals. For conversion information, see the ASCII Character Set tables in the appropriate host chapter. Numeric bar codes begin on page D-1 in Chapter D, Numeric Bar Codes. In case of an error, or to change the selection, scan Cancel on page D-7. Scan Prefix Scan Suffix Miscellaneous Scanner Options Scan Data Transmission Format To change the Scan Data Transmission Format, scan the Scan Options bar code below. Then select one of four options: • • • • Data As Is When a selection is made, scan the Enter bar code on page 9-8. In case of a mistake, scan the Data Format Cancel bar code on page 9-8. To program a carriage return/enter after each bar code scanned, scan the following bar codes in order: 1. 2. 3. Enter (on page 9-8) Scan Options *Data As Is 9-7 9-8 WLS 8400 Product Reference Guide Scan Data Transmission Format (continued) Enter Data Format Cancel Miscellaneous Scanner Options FN1 Substitution Values The Wedge and USB HID Keyboard hosts support a FN1 Substitution feature. When enabled any FN1 character (0x1b) in an EAN128 bar code is substituted with a value. This value defaults to 7013 (Enter Key) 1. To select a FN1 Substitution Value, scan the bar code below. Set FN1 Substitution Value 2. Look up the keystroke desired for FN1 Substitution in the ASCII Character Set table for the currently installed host interface. Enter the 4-digit "ASCII Value" by scanning each digit in the Numeric Bar Codes on page D-1. 3. To correct an error or change the selection, scan CANCEL. To enable FN1 Substitution for Wedge, scan the Enable Keyboard Wedge FN1 Substitution bar code on page 5-15. To enable FN1 Substitution for USB HID Keyboard, scan the Enable USB Keyboard FN1 Substitution bar code on page 7-14. Transmit “No Read” Message Scan a bar code below to select whether or not a “No Read” message is transmitted. When enabled, the characters NR are transmitted when a bar code is not decoded. When disabled, if a symbol does not decode, nothing is sent to the host. Enable No Read *Disable No Read 9-9 9-10 WLS 8400 Product Reference Guide 10 Advanced Data Formatting Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 Rules: Criteria Linked to Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 Using ADF Bar Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 ADF Bar Code Menu Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4 Rule 1: The Code 128 Scanning Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5 Rule 2: The UPC Scanning Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5 Alternate Rule Sets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6 Rules Hierarchy (in Bar Codes) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7 Default Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-8 Special Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9 Pause Duration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9 Begin New Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9 Save Rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9 Erase. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10 Quit Entering Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10 Disable Rule Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11 10-2 WLS 8400 Product Reference Guide Criteria . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12 Code Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12 Code Lengths. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-16 Message Containing A Specific Data String. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-22 Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-27 Send Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-27 Setup Field(s) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-31 Modify Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-38 Pad Data with Spaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-40 Pad Data with Zeros . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-46 Beeps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-52 Send Keystroke (Control Characters and Keyboard Characters) . . . . . . . . . . . . . . . . 10-53 Send Right Control Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-96 Send Graphic User Interface (GUI) Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-96 Turn On/Off Rule Sets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-103 Alphanumeric Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-105 Advanced Data Formatting Introduction Advanced Data Formatting (ADF) is a means of customizing data before transmission to the host device. Scan data can be edited to suit the particular requirements. ADF can be implemented through scanning a related series of bar codes, which begin on page 10-9 which allows the scanner to be setup and programmed with Advanced Data Formatting (ADF) Rules. Rules: Criteria Linked to Actions In ADF, data is customized through rules. These rules perform detailed actions when the data meets certain criteria. One rule may consist of single or multiple criteria applied to single or multiple actions. For instance, a data formatting rule could be the following: Criteria:When scan data is Code 39, length 12, and data at the start position is the string “129”, Actions:pad all sends with zeros to length 8, send all data up to X, send a space. If a Code 39 bar code of 1299X1559828 is scanned, the following is transmitted: 00001299 . If a Code 39 bar code of 1299X15598 is scanned, this rule is ignored because the length criteria has not been met. The rule specifies the editing conditions and requirements before data transmission occurs. Using ADF Bar Codes When a rule is programed, make sure the rule is logically correct. Plan ahead before starting to scan. To program each data formatting rule: • • • Start the Rule. Scan the Begin New Rule bar code on page 10-9. Criteria. Scan the bar codes for all pertinent criteria. Criteria can include code type (e.g., Code 128), code length, or data that contains a specific character string (e.g., the digits “129”). These options are described in Criteria on page 10-12. Actions. Scan all actions related to, or affecting, these criteria. The actions of a rule specify how to format the data for transmission. These options are described in ADF Bar Code Menu Example on page 10-4. 10-3 10-4 WLS 8400 Product Reference Guide • Save the Rule. Scan the Save Rule bar code on page 10-9. This places the rule in the “top” position in the rule buffer. • In case of errors made during this process, some special-purpose bar codes may be useful: Erase Criteria and Start Again, Erase Actions and Start Again, Erase Previously Saved Rule, etc. Criteria, actions, and entire rules may be erased by scanning the appropriate bar code (see page 10-10). Use the Beeper Definitions on page 2-4 as a guide for the programming steps. ADF Bar Code Menu Example This section provides an example of how ADF rules are entered and used for scan data. An auto parts distribution center wants to encode manufacturer ID, part number, and destination code into their own Code 128 bar codes. The distribution center also has products that carry UPC bar codes, placed there by the manufacturer. The Code 128 bar codes have the following format: MMMMMPPPPPDD Where: M = Manufacturer ID P = Part Number D = Destination Code The distribution center uses a PC with dedicated control characters for manufacturer ID , part number , and destination code . At this center the UPC data is treated as manufacturer ID code. The following rules need to be entered: When scanning data of code type Code 128, send the next 5 characters, send the manufacturer ID key , send the next 5 characters, send the part number key , send the next 2 characters, send the destination code key . When scanning data of code type UPC/EAN, send all data, send the manufacturer ID key . To enter these rules, follow the steps below: Advanced Data Formatting Rule 1: The Code 128 Scanning Rule Step Bar Code On Page Beep Indication 1 Begin New Rule 10-9 High High 2 Code 128 10-13 High High 3 Send next 5 characters 10-29 High High 4 Send 10-56 High High 5 Send next 5 characters 10-29 High High 6 Send 10-57 High High 7 Send next 2 characters 10-28 High High 8 Send 10-55 High High 9 Save Rule 10-9 High Low High Low On Page Beep Indication Rule 2: The UPC Scanning Rule Step Bar Code 1 Begin New Rule 10-9 High High 2 UPC/EAN 10-15 High High 3 Send all remaining data 10-28 High High 4 Send 10-56 High High 5 Save Rule 10-9 High Low High Low In case of errors while entering this rule, scan the Quit Entering Rules bar code on page 10-10. If the rule is already saved, scan the Erase Previously Saved Rule bar code on page 10-10. Alternate Rule Sets ADF rules may be grouped into one of four alternate sets which can be turned on and off when needed. This is useful to format the same message in different ways. For example, a Code 128 bar code contains the following information: Class (2 digits), Stock Number (8) digits, Price (5 digits) This bar code might look like this: 245671243701500 10-5 10-6 WLS 8400 Product Reference Guide where: Class = 24 Stock Number = 56712437 Price = 01500 Ordinarily, data is sent as follows: 24 (class key) 56712437 (stock key) 01500 (enter key) But, when there is a sale, send only the following: 24 (class key) 56712437 (stock key) and the cashier keys the price manually. To implement this, first enter an ADF rule that applies to the normal situation. This rule may look like this: When scanning a bar code of length 15, send the next 2 characters, send the class key, send the next 8 characters, send the stock key, send the data that remains, send the Enter key. The “sale” rule may look like this: When scanning a bar code of length 15, send the next 2 characters, send the class key, send the next 8 characters, send the stock key. To switch between the two sets of rules, a “switching rule” must be programmed. This rule specifies what type of bar code must be scanned to switch between the rule sets. For example, in the case of the “sale” rule above, the rule programmer wants the cashier to scan the bar code “M” before a sale. To do this, a rule can be entered as follows: When scanning a bar code of length 1 that begins with “M”, select rule set number 1. Another rule could be programmed to switch back. When scanning a bar code of length 1 that begins with “N”, turn off rule set number 1. Advanced Data Formatting The switching back to normal rules can also be done in the “sale” rule. For example, the rule may look like this: When scanning a bar code of length 15, send the next 2 characters, send the class key, send the next 8 characters, send the stock key, turn off rule set 1. It is recommended that the Disable All Rule Sets bar code on page 10-11 be scanned after programming a rule belonging to an alternate rule set. In addition to enabling and disabling rule sets within the rules, it is possible to enable or disable them by scanning the appropriate bar codes on 10-11. Rules Hierarchy (in Bar Codes) The order of programming individual rules is important.The most general rule should be programmed last. All programmed rules are stored in a buffer. As they are programmed, they are stored at the “top” of a rules list. If three rules have been created, the list would be configured as follows: Third Rule Second Rule First Rule When data is scanned, the rules list is checked from top to bottom to determine if the criteria matches (and therefore, if the actions should occur). Input is modified into the data format specified by the first matching set of criteria it finds. Be sure that the most general rule is the last one programmed. For example, if the THIRD rule states: When scanning a bar code of any length, send all data, then send the ENTER key. And the SECOND rule states: When scanning a Code 128 bar code of length 12, send the first four characters, then send the ENTER key, then send all remaining data. If a Code 128 bar code of length 12 were scanned, the THIRD rule would be in effect. The SECOND rule would appear to not function. Note also that ADF rules are actually created when the standard data editing functions are used. Scan options are entered as ADF rules, and the hierarchy mentioned above also applies to them. For the scanner, this applies to prefix/suffix programming in the parameter Scan Data Transmission Format. 10-7 10-8 WLS 8400 Product Reference Guide These rules reside in the same “rule list” as ADF Rules, so the order of their creation is also important. Default Rules Every unit has a default rule to send all scan data. Units with custom software may have one or more default rules burned in. The rules hierarchy checks user programmable rules first, then the default rules. Default rules can be disabled by entering the following general rule in the user programmable buffer: When receiving scan data, send all data. Since this rule always applies, ADF never goes into the default rules. Advanced Data Formatting Special Commands Pause Duration This parameter along with the Send Pause parameter on page 10-33 allows a pause to be inserted in the data transmission. Pauses are set by scanning a two-digit number (i.e., two bar codes), and are measured in 0.1 second intervals. For example, scanning bar codes “0” and “1” inserts a 0.1 second pause; “0” and “5” gives a 0.5 second delay. Numeric bar codes begin on page D-1 in Chapter D, Numeric Bar Codes. In case of an error, or to change the selection, scan Numeric Cancel on page D-6. Pause Duration Begin New Rule Scan this bar code to start entering a new rule . Begin New Rule Save Rule Scan this bar code to save the entered rule. Save Rule 10-9 10-10 WLS 8400 Product Reference Guide Erase Use these bar codes to erase criteria, actions, or rules. Erase Criteria And Start Again Erase Actions And Start Again Erase Previously Saved Rule Erase All Rules Quit Entering Rules Scan this bar code to quit entering rules. Quit Entering Rules Advanced Data Formatting Disable Rule Set Use these bar codes to disable rule sets. Disable Rule Set 1 Disable Rule Set 2 Disable Rule Set 3 Disable Rule Set 4 Disable All Rule Sets 10-11 10-12 WLS 8400 Product Reference Guide Criteria Code Types Select any number of code types to be affected. All selected codes must be scanned in succession, prior to selecting other criteria. If a code type is not selected, all code types are affected. Scan the bar codes for all code types desired before selecting other criteria. Code 39 Codabar RSS 14 RSS Limited Advanced Data Formatting RSS Expanded Code 128 10-13 10-14 WLS 8400 Product Reference Guide Code Types (continued) D 2 OF 5 IATA 2 OF 5 I 2 OF 5 Code 93 UPC-A UPC-E Advanced Data Formatting Code Types (continued) EAN-8 EAN-13 MSI UCC/EAN 128 UPC-E1 Bookland EAN 10-15 10-16 WLS 8400 Product Reference Guide Code Types (continued) Trioptic Code 39 Code 11 EAN 128 Advanced Data Formatting Code Lengths Define the number of characters the selected code type must contain. If a code length is not selected, selected code types of any length are affected. Scan these bar codes to define the number of characters the selected code types must contain. Select one length per rule only. 1 Character 2 Characters 3 Characters 4 Characters 10-17 10-18 WLS 8400 Product Reference Guide Code Lengths (continued) 5 Characters 6 Characters 7 Characters 8 Characters 9 Characters 10 Characters Advanced Data Formatting Code Lengths (continued) 11 Characters 12 Characters 13 Characters 14 Characters 15 Characters 16 Characters 10-19 10-20 WLS 8400 Product Reference Guide Code Lengths (continued) 17 Characters 18 Characters 19 Characters 20 Characters 21 Characters 22 Characters Advanced Data Formatting Code Lengths (continued) 23 Characters 24 Characters 25 Characters 26 Characters 27 Characters 28 Characters 10-21 10-22 WLS 8400 Product Reference Guide Code Lengths (continued) 29 Characters 30 Characters Advanced Data Formatting Message Containing A Specific Data String Use this feature to select whether the formatting affects data that begins with a specific character or data string, or contains a specific character or data string. There are 4 features: • • • • Specific String at Start Specific String, Any Location Any Message OK Rule Belongs to Set Specific String at Start Scan this bar code, then scan the bar codes representing the desired character or characters (up to a total of 8) in the Alphanumeric Keyboard on page 10-107. After scanning the following bar code: 1. Enter a string using the Alphanumeric Keyboard beginning on page 10-107. 2. Scan End of Message on page 10-118. Specific String At Start 10-23 10-24 WLS 8400 Product Reference Guide Specific String, Any Location Scan this bar code, then, using the Numeric Keypad on page 10-25, scan a two-digit number representing the position (use a leading “zero” if necessary). Then scan the desired character or characters (up to a total of 8) on the Alphanumeric Keyboard on page 10-107, followed by the End of Message bar code on page 10-118. After scanning the following bar code: 1. Enter a location using the “Numeric Keypad” on page 25. 2. Enter a string using the Alphanumeric Keyboard beginning on page 10-107. 3. Scan End of Message on page 10-118. Specific String Any Location Any Message OK By not scanning any bar code, all selected code types are formatted, regardless of information contained. Advanced Data Formatting Numeric Keypad Bar codes on this page should not be confused with those on the alphanumeric keyboard. 0 1 2 3 4 5 10-25 10-26 WLS 8400 Product Reference Guide Numeric Keypad (continued) 6 7 8 9 Cancel Advanced Data Formatting Rule Belongs To Set Select the set a rule belongs to. (There are four possible rule sets.) See Alternate Rule Sets on page 10-5 for more information about rule sets. Scan a bar code below to select which set a rule belongs to. Rule Belongs To Set 1 Rule Belongs To Set 2 Rule Belongs To Set 3 Rule Belongs To Set 4 10-27 10-28 WLS 8400 Product Reference Guide Actions Select how to format the data for transmission. Send Data Send all data that remains, send all data up to a specific character selected from the Alphanumeric Keyboard on page 10-107, or send the next N characters. N = any number from 1 to 254, selected from the Alphanumeric Keyboard. Use these bar codes to send data. Send Data Up To Character Send All Data That Remains Send Next Character Send Next 2 Characters Send Next 3 Characters Advanced Data Formatting Send Data (continued) Send Next 4 Characters Send Next 5 Characters Send Next 6 Characters Send Next 7 Characters Send Next 8 Characters Send Next 9 Characters 10-29 10-30 WLS 8400 Product Reference Guide Send Data (continued) Send Next 10 Characters Send Next 11 Characters Send Next 12 Characters Send Next 13 Characters Send Next 14 Characters Send Next 15 Characters Advanced Data Formatting Send Data (continued) Send Next 16 Characters Send Next 17 Characters Send Next 18 Characters Send Next 19 Characters Send Next 20 Characters 10-31 10-32 WLS 8400 Product Reference Guide Setup Field(s) Table 10-1. Setup Field(s) Definitions Parameter Description Page Move Cursor Move Cursor To a Character Scan the Move Cursor To Character bar code on page 10-33, then any printable ASCII character from the 10-33 Alphanumeric Keyboard. When this is used, the cursor moves to the position after the matching character. If the character is not there, the rule fails and ADF tries the next rule. Move Cursor to Start of Data Scan this bar code to move cursor to the beginning of the data. 10-33 Move Cursor Past a Character This parameter moves the cursor past all sequential 10-33 occurrences of a selected character. For example, if the selected character is ‘A’, then the cursor moves past ‘A’, ‘AA’, ‘AAA’, etc. Scan the Move Cursor Past Character bar code on page 10-33, then select a character from the Alphanumeric Keyboard. If the character is not there, the cursor does not move (i.e., has no effect). Skip Ahead “N” Characters Scan one of these bar codes to select the desired number of 10-34 positions to move the cursor ahead. Skip Back “N” Characters Scan one of these bar codes to select the desired number of 10-36 positions to move the cursor back. Send Preset Value Send prefix and/or suffix value by scanning the appropriate 10-38 bar code. These values must be set using the Scan Prefix and Scan Suffix bar codes on page 9-6. Advanced Data Formatting Move Cursor Scan a bar code below to move the cursor in relation to a specified character. Then enter a character by scanning a bar code from the Alphanumeric Keyboard beginning on page 10107. If there is no match when the rule is interpreted and the rule fails, the next rule is checked. Move Cursor To Character Move Cursor To Start Move Cursor Past Character Send Pause Scan the bar code below to insert a pause in the transmission of data. The length of this pause is controlled by the value of the Pause Duration parameter. Send Pause 10-33 10-34 WLS 8400 Product Reference Guide Skip Ahead Use the following bar codes to skip ahead characters. Skip Ahead 1 Character Skip Ahead 2 Characters Skip Ahead 3 Characters Skip Ahead 4 Characters Skip Ahead 5 Characters Skip Ahead 6 Characters Advanced Data Formatting Skip Ahead (continued) Skip Ahead 7 Characters Skip Ahead 8 Characters Skip Ahead 9 Characters Skip Ahead 10 Characters 10-35 10-36 WLS 8400 Product Reference Guide Skip Back Use the following bar codes to skip back characters. Skip Back 1 Character Skip Back 2 Characters Skip Back 3 Characters Skip Back 4 Characters Skip Back 5 Characters Skip Back 6 Characters Advanced Data Formatting Skip Back (continued) Skip Back 7 Characters Skip Back 8 Characters Skip Back 9 Characters Skip Back 10 Characters 10-37 10-38 WLS 8400 Product Reference Guide Send Preset Value Use these bar codes to send preset values. These values must be set using the Scan Prefix and Scan Suffix bar codes on page 9-6. Send Prefix Send Suffix Advanced Data Formatting Modify Data Modify data in the ways listed. The following actions work for all send commands that follow it within a rule. If pad zeros to length 6, send next 3 characters, stop padding, send next 5 characters is programmed, three zeros are added to the first send, and the next send is unaffected by the padding. These options do not apply to the Send Keystroke or Send Preset Value options. Remove All Spaces To remove all spaces in the send commands that follow, scan this bar code. Remove All Spaces Crunch All Spaces To leave one space between words, scan this bar code. This also removes all leading and trailing spaces. Crunch All Spaces Stop Space Removal Scan this bar code to disable space removal. Stop Space Removal 10-39 10-40 WLS 8400 Product Reference Guide Modify Data (Continued) Remove Leading Zeros Scan this bar code to remove all leading zeros. Remove Leading Zeros Stop Zero Removal Scan this bar code to disable the removal of zeros. Stop Zero Removal Advanced Data Formatting Pad Data with Spaces To pad data to the left, scan the bar code containing the desired number of spaces. This parameter is activated by Send commands. Pad Spaces To Length 1 Pad Spaces To Length 2 Pad Spaces To Length 3 Pad Spaces To Length 4 10-41 10-42 WLS 8400 Product Reference Guide Pad Data with Spaces (continued) Pad Spaces To Length 5 Pad Spaces To Length 6 Pad Spaces To Length 7 Pad Spaces To Length 8 Pad Spaces To Length 9 Pad Spaces To Length 10 Advanced Data Formatting Pad Data with Spaces (continued) Pad Spaces To Length 11 Pad Spaces To Length 12 Pad Spaces To Length 13 Pad Spaces To Length 14 Pad Spaces To Length 15 Pad Spaces To Length 16 10-43 10-44 WLS 8400 Product Reference Guide Pad Data with Spaces (continued) Pad Spaces To Length 17 Pad Spaces To Length 18 Pad Spaces To Length 19 Pad Spaces To Length 20 Pad Spaces To Length 21 Pad Spaces To Length 22 Advanced Data Formatting Pad Data with Spaces (continued) Pad Spaces To Length 23 Pad Spaces To Length 24 Pad Spaces To Length 25 Pad Spaces To Length 26 Pad Spaces To Length 27 Pad Spaces To Length 28 10-45 10-46 WLS 8400 Product Reference Guide Pad Data with Spaces (continued) Pad Spaces To Length 29 Pad Spaces To Length 30 Stop Pad Spaces Advanced Data Formatting Pad Data with Zeros To pad data to the left, scan the bar code containing the desired number of zeros. This parameter is activated by Send commands. Pad Zeros To Length 1 Pad Zeros To Length 2 Pad Zeros To Length 3 Pad Zeros To Length 4 10-47 10-48 WLS 8400 Product Reference Guide Pad Data with Zeros (continued) Pad Zeros To Length 5 Pad Zeros To Length 6 Pad Zeros To Length 7 Pad Zeros To Length 8 Pad Zeros To Length 9 Pad Zeros To Length 10 Advanced Data Formatting Pad Data with Zeros (continued) Pad Zeros To Length 11 Pad Zeros To Length 12 Pad Zeros To Length 13 Pad Zeros To Length 14 Pad Zeros To Length 15 Pad Zeros To Length 16 10-49 10-50 WLS 8400 Product Reference Guide Pad Data with Zeros (continued) Pad Zeros To Length 17 Pad Zeros To Length 18 Pad Zeros To Length 19 Pad Zeros To Length 20 Pad Zeros To Length 21 Pad Zeros To Length 22 Advanced Data Formatting Pad Data with Zeros (continued) Pad Zeros To Length 23 Pad Zeros To Length 24 Pad Zeros To Length 25 Pad Zeros To Length 26 Pad Zeros To Length 27 Pad Zeros To Length 28 10-51 10-52 WLS 8400 Product Reference Guide Pad Data with Zeros (continued) Pad Zeros To Length 29 Pad Zeros To Length 30 Stop Pad Zeros Advanced Data Formatting Beeps Select a beep sequence for each ADF rule. Beep Once Beep Twice Beep Three Times 10-53 10-54 WLS 8400 Product Reference Guide Send Keystroke (Control Characters and Keyboard Characters) Control Characters Scan the “Send __” bar code for the desired keystroke Send Control 2 Send Control A Send Control B Send Control C . Advanced Data Formatting Control Characters (continued) Send Control D Send Control E Send Control F Send Control G Send Control H Send Control I 10-55 10-56 WLS 8400 Product Reference Guide Control Characters (continued) Send Control J Send Control K Send Control L Send Control M Send Control N Send Control O Advanced Data Formatting Control Characters (continued) Send Control P Send Control Q Send Control R Send Control S Send Control T Send Control U 10-57 10-58 WLS 8400 Product Reference Guide Control Characters (continued) Send Control V Send Control W Send Control X Send Control Y Send Control Z Send Control [ Advanced Data Formatting Control Characters (continued) Send Control \ Send Control ] Send Control 6 Send Control - 10-59 10-60 WLS 8400 Product Reference Guide Keyboard Characters Scan the “Send __” bar code for the desired keyboard characters Send Space Send ! Send “ Send # Send $ Send % Advanced Data Formatting Keyboard Characters (continued) Send & Send ‘ Send ( Send ) Send * Send + 10-61 10-62 WLS 8400 Product Reference Guide Keyboard Characters (continued) Send , Send - Send . Send / Send 0 Send 1 Advanced Data Formatting Keyboard Characters (continued) Send 2 Send 3 Send 4 Send 5 Send 6 Send 7 10-63 10-64 WLS 8400 Product Reference Guide Keyboard Characters (continued) Send 8 Send 9 Send : Send ; Send < Send = Advanced Data Formatting Keyboard Characters (continued) Send > Send ? Send @ Send A Send B Send C 10-65 10-66 WLS 8400 Product Reference Guide Keyboard Characters (continued) Send D Send E Send F Send G Send H Send I Advanced Data Formatting Keyboard Characters (continued) Send J Send K Send L Send M Send N Send O 10-67 10-68 WLS 8400 Product Reference Guide Keyboard Characters (continued) Send P Send Q Send R Send S Send T Send U Advanced Data Formatting Keyboard Characters (continued) Send V Send W Send X Send Y Send Z Send [ 10-69 10-70 WLS 8400 Product Reference Guide Keyboard Characters (continued) Send \ Send ] Send ^ Send _ Send ` Send a Advanced Data Formatting Keyboard Characters (continued) Send b Send c Send d Send e Send f Send g 10-71 10-72 WLS 8400 Product Reference Guide Keyboard Characters (continued) Send h Send i Send j Send k Send l Send m Advanced Data Formatting Keyboard Characters (continued) Send n Send o Send p Send q Send r Send s 10-73 10-74 WLS 8400 Product Reference Guide Keyboard Characters (continued) Send t Send u Send v Send w Send x Send y Advanced Data Formatting Keyboard Characters (continued) Send z Send { Send | Send } Send ~ 10-75 10-76 WLS 8400 Product Reference Guide Send ALT Characters Send Alt 2 Send Alt A Send Alt B Send Alt C Send Alt D Send Alt E Advanced Data Formatting Send ALT Characters (continued) Send Alt F Send Alt G Send Alt H Send Alt I Send Alt J Send Alt K 10-77 10-78 WLS 8400 Product Reference Guide Send ALT Characters (continued) Send Alt L Send Alt M Send Alt N Send Alt O Send Alt P Send Alt Q Advanced Data Formatting Send ALT Characters (continued) Send Alt R Send Alt S Send Alt T Send Alt U Send Alt V Send Alt W 10-79 10-80 WLS 8400 Product Reference Guide Send ALT Characters (continued) Send Alt X Send Alt Y Send Alt Z Send Alt [ Send Alt \ Send Alt ] Advanced Data Formatting Send ALT Characters (continued) Send Alt 6 Send Alt - 10-81 10-82 WLS 8400 Product Reference Guide Send Keypad Characters Send Keypad * Send Keypad + Send Keypad - Send Keypad . Send Keypad / Send Keypad 0 Advanced Data Formatting Send Keypad Characters (continued) Send Keypad 1 Send Keypad 2 Send Keypad 3 Send Keypad 4 Send Keypad 5 Send Keypad 6 10-83 10-84 WLS 8400 Product Reference Guide Send Keypad Characters (continued) Send Keypad 7 Send Keypad 8 Send Keypad 9 Send Keypad Enter Send Keypad Numlock NUM LOCK Send Break Key Advanced Data Formatting Send Keypad Characters (continued) Send Delete Key Send Page Up Key Send End Key Send Page Down Key Send Pause Key Send Scroll Lock Key 10-85 10-86 WLS 8400 Product Reference Guide Send Keypad Characters (continued) Send Backspace Key Send Tab Key Send Print Screen Key Send Insert Key Send Home Key Send Enter Key Advanced Data Formatting Send Keypad Characters (continued) Send Escape Key Send Up Arrow Key Send Down Arrow Key Send Left Arrow Key Send Right Arrow Key 10-87 10-88 WLS 8400 Product Reference Guide Send Function Key Send F1 Key Send F2 Key Send F3 Key Send F4 Key Send F5 Key Send F6 Key Advanced Data Formatting Send Function Key (continued) Send F7 Key Send F8 Key Send F9 Key Send F10 Key Send F11 Key Send F12 Key 10-89 10-90 WLS 8400 Product Reference Guide Send Function Key (continued) Send F13 Key Send F14 Key Send F15 Key Send F16 Key Send F17 Key Send F18 Key Advanced Data Formatting Send Function Key (continued) Send F19 Key Send F20 Key Send F21 Key Send F22 Key Send F23 Key Send F24 Key 10-91 10-92 WLS 8400 Product Reference Guide Send Function Key (continued) Send PF1 Key Send PF2 Key Send PF3 Key Send PF4 Key Send PF5 Key Send PF6 Key Advanced Data Formatting Send Function Key (continued) Send PF7 Key Send PF8 Key Send PF9 Key Send PF10 Key Send PF11 Key Send PF12 Key 10-93 10-94 WLS 8400 Product Reference Guide Send Function Key (continued) Send PF13 Key Send PF14 Key Send PF15 Key Send PF16 Key Send PF17 Key Send PF18 Key Advanced Data Formatting Send Function Key (continued) Send PF19 Key Send PF20 Key Send PF21 Key Send PF22 Key Send PF23 Key Send PF24 Key 10-95 10-96 WLS 8400 Product Reference Guide Send Function Key (continued) Send PF25 Key Send PF26 Key Send PF27 Key Send PF28 Key Send PF29 Key Send PF30 Key Advanced Data Formatting Send Right Control Key The “Send Right Control Key” action sends a tap (press and release) of the Right Control Key. Send Right Control Key Send Graphic User Interface (GUI) Characters The “Send Graphic User Interface Character” actions tap the specified key while holding the System Dependent Graphic User Interface (GUI) Key. The definition of the Graphic User Interface key is dependant upon the attached system: Send GUI 0 Send GUI 1 10-97 10-98 WLS 8400 Product Reference Guide Send GUI 2 Send GUI 3 Advanced Data Formatting Send Graphic User Interface (GUI) Characters (continued) Send GUI 4 Send GUI 5 Send GUI 6 Send GUI 7 Send GUI 8 Send GUI 9 10-99 10-100 WLS 8400 Product Reference Guide Send Graphic User Interface (GUI) Characters (continued) Send GUI A Send GUI B Send GUI C Send GUI D Send GUI E Send GUI F Advanced Data Formatting Send Graphic User Interface (GUI) Characters (continued) Send GUI G Send GUI H Send GUI I Send GUI J Send GUI K Send GUI L 10- 10-102 WLS 8400 Product Reference Guide Send Graphic User Interface (GUI) Characters (continued) Send GUI M Send GUI N Send GUI O Send GUI P Send GUI Q Send GUI R Advanced Data Formatting Send Graphic User Interface (GUI) Characters (continued) Send GUI S Send GUI T Send GUI U Send GUI V Send GUI W Send GUI X 10- 10-104 WLS 8400 Product Reference Guide Send Graphic User Interface (GUI) Characters (continued) Send GUI Y Send GUI Z Advanced Data Formatting Turn On/Off Rule Sets Use these bar codes to turn rule sets on and off. Turn On Rule Set 1 Turn On Rule Set 2 Turn On Rule Set 3 Turn On Rule Set 4 10- 10-106 WLS 8400 Product Reference Guide Turn On/Off Rule Sets (continued) Use these bar codes to turn rule sets on and off. Turn Off Rule Set 1 Turn Off Rule Set 2 Turn Off Rule Set 3 Turn Off Rule Set 4 Advanced Data Formatting Alphanumeric Keyboard Space # $ % * + 10- 10-108 WLS 8400 Product Reference Guide Alphanumeric Keyboard (continued) (Dash) . / ! “ & Advanced Data Formatting Alphanumeric Keyboard (continued) “ ( ) : ; < 10- 10-110 WLS 8400 Product Reference Guide Alphanumeric Keyboard (continued) = > ? @ [ \ Advanced Data Formatting Alphanumeric Keyboard (continued) ] ^ _ (Underscore) ` Alphanumeric Keyboard (continued) Bar codes on this page should not be confused with those on the numeric keypad. 10- 10-112 WLS 8400 Product Reference Guide 0 1 2 3 Advanced Data Formatting Alphanumeric Keyboard (continued) 4 5 6 7 8 9 10- 10-114 WLS 8400 Product Reference Guide Alphanumeric Keyboard (continued) A B C D E F Advanced Data Formatting Alphanumeric Keyboard (continued) G H I J K L 10- 10-116 WLS 8400 Product Reference Guide Alphanumeric Keyboard (continued) M N O P Q R Advanced Data Formatting Alphanumeric Keyboard (continued) S T U V W X 10- 10-118 WLS 8400 Product Reference Guide Alphanumeric Keyboard (continued) Y Z Cancel End of Message Advanced Data Formatting Alphanumeric Keyboard (continued) a b c d e f 10- 10-120 WLS 8400 Product Reference Guide Alphanumeric Keyboard (continued) g h i j k l Advanced Data Formatting Alphanumeric Keyboard (continued) m n o p q r 10- 10-122 WLS 8400 Product Reference Guide Alphanumeric Keyboard (continued) s t u v w x Advanced Data Formatting Alphanumeric Keyboard (continued) y z { | } ~ 10- 10-124 WLS 8400 Product Reference Guide A Standard Default Parameters A-2 WLS 8400 Product Reference Guide Standard Default Parameters Table A-1. Standard Default Parameters Table Parameter Default Page Number User Preferences Set Default Parameter All Defaults 4-5 Beeper Tone High 4-5 Beeper Volume High 4-6 Power Mode Continuous On 4-7 Laser On Time 3.0 sec 4-7 Beep After Good Decode Enable 4-8 Trigger Mode Level 4-8 Aim Duration 0.0 sec 4-10 Keyboard Wedge Host Type IBM PC/AT& IBM PC Compatibles1 5-7 Keyboard Wedge Country Types (Country Codes) North American 5-8 Ignore Unknown Characters Enable 5-10 Keystroke Delay 0 msec (No Delay) 5-10 Intra-Keystroke Delay Disable 5-11 Alternate Numeric Keypad Emulation Disable 5-12 Caps Lock On Disable 5-12 Caps Lock Override Disable 5-13 Keyboard Wedge Host Parameters 1User selection is required to configure this interface and this is the most common selection. A-3 A-4 WLS 8400 Product Reference Guide Table A-1. Standard Default Parameters Table (Continued) Parameter Default Page Number Convert Wedge Data Do Not Convert Wedge Data 5-14 Function Key Mapping Disable 5-14 FN1 Substitution Disable 5-15 Send Make and Break Send Make and Break Scan Codes 5-15 RS-232 Host Types Standard RS-2321 6-9 Baud Rate 9600 6-10 Parity None 6-12 Check Receive Errors Enable 6-13 Stop Bit Select 1 Stop Bit 6-14 Data Bits 8-Bit 6-14 Hardware Handshaking None 6-15 Software Handshaking None 6-18 Host Serial Response Time-out Minimum: 2 Sec 6-20 RTS Line State Host: Low RTS 6-21 Beep on Disable 6-22 Intercharacter Delay Minimum: 0 msec 6-23 Nixdorf Mode A/B and OPOS/JPOS Beep/LED Options Normal Operation 6-24 Ignore Unknown Characters Send Bar Code 6-25 RS-232 Host Parameters 1User selection is required to configure this interface and this is the most common selection. Standard Default Parameters Table A-1. Standard Default Parameters Table (Continued) Parameter Default Page Number USB Host Parameters USB Device Type HID Keyboard Emulation 7-7 USB Country Keyboard Types (Country Codes) North American 7-8 USB Keystroke Delay No Delay (0 msec) 7-10 USB CAPS Lock Override Disable 7-11 USB Ignore Unknown Characters Enable 7-12 Emulate Keypad Disable 7-13 USB Keyboard FN1 Substitution Disable 7-14 Function Key Mapping Disable 7-14 Simulated Caps Lock Disable 7-15 Convert Case No Case Conversion 7-15 UPC-A Enable 8-10 UPC-E Enable 8-10 UPC-E1 Disable 8-11 EAN-13/JAN 13 Enable 8-11 EAN-8/JAN 8 Enable 8-12 Bookland EAN Disable 8-12 Decode UPC/EAN/JAN Supplementals (2 and 5 digits) Ignore Supplementals 8-13 UPC/EAN/JAN Supplemental Redundancy 14 8-15 UPC/EAN 1User selection is required to configure this interface and this is the most common selection. A-5 A-6 WLS 8400 Product Reference Guide Table A-1. Standard Default Parameters Table (Continued) Parameter Default Page Number Transmit UPC-A Check Digit Enable 8-15 Transmit UPC-E Check Digit Enable 8-16 Transmit UPC-E1 Check Digit Enable 8-16 UPC-A Preamble System Character 8-17 UPC-E Preamble System Character 8-18 UPC-E1 Preamble System Character 8-19 Convert UPC-E to A Disable 8-20 Convert UPC-E1 to A Disable 8-21 EAN-8/JAN-8 Extend Disable 8-22 Code 128 Enable 8-22 UCC/EAN-128 Enable 8-23 ISBT 128 Enable 8-23 Code 39 Enable 8-24 Trioptic Code 39 Disable 8-24 Convert Code 39 to Code 32 Disable 8-25 Code 32 Prefix Disable 8-26 Set Length(s) for Code 39 2 to 55 8-27 Code 39 Check Digit Verification Disable 8-29 Code 128 Code 39 1User selection is required to configure this interface and this is the most common selection. Standard Default Parameters Table A-1. Standard Default Parameters Table (Continued) Parameter Default Page Number Transmit Code 39 Check Digit Disable 8-30 Code 39 Full ASCII Conversion Disable 8-31 Code 93 Disable 8-32 Set Lengths for Code 93 4 to 55 8-32 Code 11 Disable 8-34 Set Lengths for Code 11 4 to 41 8-34 Code 11 Check Digit Verification One Check Digit 8-36 Transmit Code 11 Check Digits Disable 8-37 Interleaved 2 of 5 (I 2 of 5) Enable 8-38 Set Lengths for Interleaved 2 of 5 14 8-38 I 2 of 5 Check Digit Verification Disable 8-41 Transmit I 2 of 5 Check Digit Disable 8-42 Convert I 2 of 5 to EAN-13 Disable 8-42 Discrete 2 of 5 Disable 8-44 Set Lengths for D 2 of 5 12 8-44 Code 93 Code 11 Interleaved 2 of 5 (I 2 of 5) Discrete 2 of 5 (D 2 of 5) 1User selection is required to configure this interface and this is the most common selection. A-7 A-8 WLS 8400 Product Reference Guide Table A-1. Standard Default Parameters Table (Continued) Parameter Default Page Number Codabar (NW - 7) Codabar Disable 8-46 Set Lengths for Codabar 5 to 55 8-47 CLSI Editing Disable 8-49 NOTIS Editing Disable 8-49 MSI Disable 8-50 Set Lengths for MSI 6 to 55 8-50 MSI Check Digits One 8-52 Transmit MSI Check Digit(s) Disable 8-53 MSI Check Digit Algorithm Mod 10/Mod 10 8-53 RSS 14 Disable 8-54 RSS Limited Disable 8-54 RSS Expanded Disable 8-55 Convert RSS to UPC/EAN Disable 8-55 Redundancy Level 1 8-56 Security Levels 0 8-58 Bi-Directional Redundancy Disable 8-60 MSI RSS (Reduced Space Symbology) Symbology - Specific Security Levels 1User selection is required to configure this interface and this is the most common selection. Standard Default Parameters Table A-1. Standard Default Parameters Table (Continued) Parameter Default Page Number Miscellaneous Scanner Options Transmit Code ID Character None 9-5 Scan Angle Normal Angle 9-6 Prefix Value 7013 9-6 Suffix Value 7013 9-6 Scan Data Transmission Format Data As Is 9-7 FN1 Substitution Values Set FN1 Substitution Value 9-9 Transmit “No Read” Message Disable No Read 9-9 1User selection is required to configure this interface and this is the most common selection. A-9 A-10 WLS 8400 Product Reference Guide B Programming Reference Symbol Code Identifiers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3 AIM Code Identifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4 B-2 WLS 8400 Product Reference Guide Programming Reference Symbol Code Identifiers Table 2-1. Symbol Code Characters Code Character Code Type A UPC-A, UPC-E, UPC-E1, EAN-8, EAN-13 B Code 39, Code 32 C Codabar D Code 128 E Code 93 F Interleaved 2 of 5 G Discrete 2 of 5, or Discrete 2 of 5 IATA H Code 11 J MSI K UCC/EAN-128 L Bookland EAN M Trioptic Code 39 R RSS Family B-3 B-4 WLS 8400 Product Reference Guide AIM Code Identifiers Each AIM Code Identifier contains the three-character string ]cm where: ] = c = m = Flag Character (ASCII 93) Code Character (see Table 2-2) Modifier Character (see Table B-3) Table 2-2. Aim Code Characters Code Character Code Type A Code 39, Code 39 Full ASCII, Code 32 C Code 128 E UPC/EAN e RSS Family F Codabar G Code 93 H Code 11 I Interleaved 2 of 5 M MSI S Discrete 2 of 5, IATA 2 of 5 X Code 39 Trioptic X Bookland EAN Programming Reference The modifier character is the sum of the applicable option values based on Table B-3. Table B-3. Modifier Characters Code Type Code 39 Option Value Option 0 No check character or Full ASCII processing. 1 Reader has checked one check character. 3 Reader has checked and stripped check character. 4 Reader has performed Full ASCII character conversion. 5 Reader has performed Full ASCII character conversion and checked one check character. 7 Reader has performed Full ASCII character conversion and checked and stripped check character. Example: A Full ASCII bar code with check character W, A+I+MI+DW, is transmitted as ]A7AIMID where 7 = (3+4). Trioptic Code 39 0 No option specified at this time. Always transmit 0. Example: A Trioptic bar code 412356 is transmitted as ]X0412356 Code 128 0 Standard data packet, no Function code 1 in first symbol position. 1 Function code 1 in first symbol character position. 2 Function code 1 in second symbol character position. Example: ACode (EAN) 128 bar code with Function 1 characterFNC1 in the first position, AIMID is transmitted as ]C1AIMID I 2 of 5 0 No check digit processing. 1 Reader has validated check digit. 3 Reader has validated and stripped check digit. Example: An I 2 of 5 bar code without check digit, 4123, is transmitted as ]I04123 Codabar 0 No check digit processing. 1 Reader has checked check digit. 3 Reader has stripped check digit before transmission. Example: A Codabar bar code without check digit, 4123, is transmitted as ]F04123 Code 93 0 No options specified at this time. Always transmit 0. Example: A Code 93 bar code 012345678905 is transmitted as ]G0012345678905 B-5 B-6 WLS 8400 Product Reference Guide Table B-3. Modifier Characters (Continued) Code Type MSI Option Value Option 0 Check digits are sent. 1 No check digit is sent. Example: An MSI bar code 4123, with a single check digit checked, is transmitted as ]M14123 D 2 of 5 0 No options specified at this time. Always transmit 0. Example: A D 2 of 5 bar code 4123, is transmitted as ]S04123 UPC/EAN 0 Standard packet in full EAN country code format, which is 13 digits for UPC-A and UPC-E (not including supplemental data). 1 Two-digit supplement data only. 2 Five-digit supplement data only. 4 EAN-8 data packet. Example: A UPC-A bar code 012345678905 is transmitted as ]E00012345678905 Bookland EAN 0 No options specified at this time. Always transmit 0. Example: A Bookland EAN bar code 123456789X is transmitted as ]X0123456789X Code 11 0 Single check digit 1 Two check digits 3 Check characters validated but not transmitted. C Sample Bar Codes UPC-A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3 UPC-E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3 UPC-E1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3 EAN-13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4 EAN-8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4 Code 39 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-4 Trioptic Code 39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5 Code 93 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5 Code 11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-5 Codabar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6 MSI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6 Interleaved 2 of 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-6 C-2 WLS 8400 Product Reference Guide Sample Bar Codes UPC-A 0 12345 67890 UPC-E 0 123456 5 1 123456 2 UPC-E1 5 C-3 C-4 WLS 8400 Product Reference Guide EAN-13 3 456789 012340 EAN-8 1234 5670 Code 39 123ABC Sample Bar Codes Trioptic Code 39 456123 Code 93 12345ABCDE Code 11 Æ1234567890Æ C-5 C-6 WLS 8400 Product Reference Guide Codabar A1234567890A MSI 123456789 Interleaved 2 of 5 12345678912345 D Numeric Bar Codes 0, 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-3 2, 3, 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-4 5, 6, 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-5 8, 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-6 Cancel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-7 D-2 WLS 8400 Product Reference Guide Numeric Bar Codes 0, 1 For parameters requiring specific numeric values, scan the appropriately numbered bar code(s). 0 1 D-3 D-4 WLS 8400 Product Reference Guide 2, 3, 4 For parameters requiring specific numeric values, scan the appropriately numbered bar code(s). 2 3 4 Numeric Bar Codes 5, 6, 7 For parameters requiring specific numeric values, scan the appropriately numbered bar code(s). 5 6 7 D-5 D-6 WLS 8400 Product Reference Guide 8, 9 For parameters requiring specific numeric values, scan the appropriately numbered bar code(s). 8 9 Numeric Bar Codes Cancel In case of an error or to change the selection, scan the bar code below. Cancel D-7 D-8 WLS 8400 Product Reference Guide Glossary AIM Automatic Identification Manufacturers, Inc. is the trade association for manufacturers of automatic identification systems. Alphanumeric A character set that contains letters, numbers and other characters such as special symbols. Aperture The opening in an optical system defined by a lens or baffle that establishes the field of view. GL-2 WLS 8400 Product Reference Guide ASCII American Standard Code for Information Interchange. A 7-bit-plus-parity code representing 128 letters, numerals, punctuation marks, and control characters. It is a standard data transmission code in the U.S. Aspect Ratio The ratio of symbol height to symbol length in a 2dimensional symbol. Autodiscrimination The ability of an interface controller to determine the code type of a scanned bar code. After this determination is made, the information content is decoded. Automatic Identification System The application of various technologies, such as bar code recognition, image recognition, voice recognition and RF/MW transponders, for the purpose of data entry into a data processing system and bypassing the key-entry component of traditional data entry. Background The area surrounding a printed symbol including the spaces and quiet zones. Bar The dark element in a printed bar code symbol. Bar Code An array of parallel rectangular bars and spaces arranged according to the encodation rules of a particular symbol specification in order to represent data in machine-readable form (i.e., Code 39). Bar Code Character A single group of bars and spaces which represent an individual number, letter, punctuation mark or other symbol. Bar Code Density The number of characters represented per unit of measurement (e.g., characters per inch). Bar Code Reader A device used to read or decode a bar code symbol. Bar Code Symbol The combination of symbol characters and features required by a particular symbology, including quiet zones, start and stop characters, data characters, check characters and other auxiliary patterns, that together form a complete scannable entity (see Symbol). Bar Height The dimension of a bar measured perpendicular to the bar width (see Y Dimension). Glossary Bar Width Thickness of a bar measured from the edge closest to the symbol start character to the trailing edge of the same bar (see X Dimension). Baud Rate A measure of the data flow or number of signaling events occurring per second. When one bit is the standard "event," this is a measure of bits per second (bps). For example, a baud rate of 50 means transmission of 50 bits of data per second. Bi-directional Denotes that a machine-readable symbol can be read successfully in two directions – either backwards or forwards. Also identifies a scanner that can operate or a bar code that can be read independent of scanning direction. Binary Denotes a numbering system to base 2 in which numbers are expressed as combinations of the digits 0 and 1 with positional weighting based on powers of 2. In computing, these can be represented electrically by 'off' and 'on' respectively or in machine-readable symbols by narrow and wide elements or by the absence or presence of a bar module. Bit Binary digit. One bit is the basic unit of binary information. Generally, eight consecutive bits compose one byte of data. The pattern of 0 and 1 values within the byte determines its meaning. Byte A sequential series of bits comprising one character and handled as one unit. Usually encoded in the ASCII format, a byte usually consists of eight bits and represents one alphabetic or special character, two decimal digits or eight binary bits. CDRH Center for Devices and Radiological Health. A federal agency responsible for regulating laser product safety. This agency specifies various laser operation classes based on power output during operation. CDRH Class 1 This is the lowest power CDRH laser classification. This class is considered intrinsically safe, even if all laser output were directed into the eye's pupil. There are no special operating procedures for this class. GL-3 GL-4 WLS 8400 Product Reference Guide CDRH Class 2 No additional software mechanisms are needed to conform to this limit. Laser operation in this class poses no danger for unintentional direct human exposure. Character A pattern of bars and spaces which either directly represents data or indicates a control function, such as a number, letter, punctuation mark, or communications control contained in a message. Character Set Those characters available for encoding in a particular bar code symbology. Check Digit A digit used to verify a correct symbol decode. The scanner inserts the decoded data into an arithmetic formula and checks that the resulting number matches the encoded check digit. Check digits are required for UPC but are optional for other symbologies. Using check digits decreases the chance of substitution errors when a symbol is decoded. Codabar A discrete self-checking code with a character set consisting of digits 0 to 9 and six additional characters: ( - $ : / , +). Code A set of unambiguous rules specifying the way in which data may be represented as numbers and letters used to represent information. Code 128 A high density symbology which allows the controller to encode all 128 ASCII characters without adding extra symbol elements. Code 3 of 9 (Code 39) A versatile and widely used alphanumeric bar code symbology with a set of 43 character types, including all uppercase letters, numerals from 0 to 9, and 7 special characters (- . / + % $ and space). The code name is derived from the fact that 3 of 9 elements representing a character are wide, while the remaining 6 are narrow. Code 49 This symbol is a stack of 2 to 8 rows. Each row encodes row count information plus data characters. For more information, go to the AIM web site or the ANSI web site (see Stacked Symbol (2D Symbols)). Glossary Code 93 An industrial symbology compatible with Code 39 but offering a full character ASCII set and a higher coding density than Code 39. Code Length Number of data characters in a bar code between the start and stop characters, not including those characters. Codeword As a symbol character value, this is an intermediate level of coding between source data and the graphical encodation in the symbol. Concatenation The construction of a string of data from two or more strings by appending each string in succession. The linking or chaining together of separate items of data in a bar code symbol or of the data contained in two or more separate bar code symbols (also referred to as message append and structured append). Continuous Code A bar code or symbol in which all spaces within the symbol are parts of characters. There are no intercharacter gaps in a continuous code. The absence of gaps allows for greater information density. Contrast The difference in reflectance between the black and white (or bar and space) areas of a symbol. Data Identifier A specified character or string of characters that defines the intended use of the data element that follows. For the purposes of automatic data capture technologies, data identifier refers to the alphanumeric identifiers as defined in ANSI MH10.8.2, formerly known as ANSI/FACT data identifiers. GL-5 GL-6 WLS 8400 Product Reference Guide Data Matrix This error correcting, 2-dimensional matrix symbology is capable of encoding various character sets including strictly numeric data, alphanumeric data and all ISO 646 (ASCII) characters, as well as special character sets. The symbology has both error detection and error correction features. Each Data Matrix symbol consists of data regions, which contain nominally square modules set out in a regular array. A dark module is a binary 1 and a light module is a binary 0. There is no specified minimum or maximum for the X or Y dimension. The data region is surrounded by a finder pattern, a perimeter to the data region that is 1 module wide, which is surrounded by a quiet zone on all four sides of the symbol. Two adjacent sides are solid dark lines used primarily to define physical size, orientation and symbol distortion. The two opposite sides consist of alternating dark and light modules. These are used primarily to define the cell structure but also assist in determining physical size and distortion. There are 2 types of Data Matrix symbologies: ECC 000 - 140 with several available levels of convolutional error correction, and ECC 200, which uses Reed-Solomon error correction. For ISO/IEC JTC 1/SC 31 purposes, only ECC 200 is recommended. The intellectual property rights associated with Data Matrix have been committed to the public domain. Data Structure The stipulation of the type of information that is included in a bar code, such as its order and format. Dead Zone An area within a scanner's field of view, in which specular reflection may prevent a successful decode. Decode To recognize a bar code symbology (e.g., UPC/EAN) and then analyze the content of the specific bar code scanned. Decode Algorithm A decoding scheme that converts pulse widths into data representation of the letters or numbers encoded within a bar code symbol. Glossary Decoder An electronic package that receives the signals from the scanning function, performs the algorithm to interpret the signals into meaningful data and provides the interface to other devices. Density Describes the relative amount of memory contained in a radio frequency identification tag (see Bar Code Density). Depth of Field The range between minimum and maximum distances at which a scanner can read a symbol with a certain minimum element width. Diffuse Reflection The component of reflected light that emanates in all directions from the reflecting surface. Discrete 2 of 5 A binary bar code symbology representing each character by a group of five bars, two of which are wide. The location of wide bars in the group determines which character is encoded; spaces are insignificant. Only numeric characters (0 to 9) and START/STOP characters may be encoded. Discrete Code A bar code or symbol in which the spaces between characters (intercharacter gaps) are not part of the code. EAN European Article Number. This European/ international version of the UPC provides its own coding format and symbology standards. Element dimensions are specified metrically. EAN is used primarily in retail. EAN/U.P.C. A fixed-length, numeric 13-digit bar code symbol consisting of 30 dark elements and 29 intervening light elements. Each character is represented by 2 bars and 2 spaces over 7 modules. A bar may be comprised of 1, 2, 3 or 4 modules. Each EAN/U.P.C. symbol consists of a leading quiet zone, a start pattern, 7 left-hand data characters, a center bar pattern, 5 right-hand data characters, a Modulo 10 check character, a stop pattern and a trailing quiet zone. U.P.C. is often considered a 12-digit code. The 13th digit of EAN/U.P.C. symbol is a derived character in the left-most position. In the case of U.P.C., this derived left-most character is a 0. Element Generic term for a bar or space. GL-7 GL-8 WLS 8400 Product Reference Guide Encoded Area Total linear dimension occupied by all characters of a code pattern, including start/stop characters and data. Error Correction A reader or decoder's use of mathematical schemes to reconstruct or replace damaged or missing symbol characters to enable the reading of the symbol data. Error Detection This occurs when error-correction characters detect that the presence of errors in the symbol exceeds the error correction capacity, and keeps the symbol from being decoded as erroneous data. Error-Correction Characters Symbol characters used for error correction and detection, calculated automatically from the other symbol characters. Error-Correction Level An indicator of the number of characters used in a symbology for error correction. A higher level of error correction allows for correcting greater potential symbol damage. Error-Detection Characters Symbol characters reserved for error detection that are calculated automatically from the other symbol characters. Fixed Beam Bar Code Reader A scanning device where scanning motion is achieved by moving the object relative to the reader; as opposed to a moving beam reader. Guard Bars Bars located at both ends and the center of a UPC and EAN symbol to provide reference points for scanning. Horizontal Bar Code A bar code or symbol with an overall length dimension that is parallel to the horizon, which resembles a picket fence. Host Computer A computer that serves other terminals in a network, providing such services as computation, database access, supervisory programs, and network control. IEC International Electrotechnical Commission. This international agency regulates laser safety by specifying various laser operation classes based on power output during operation. Glossary IEC (825) Class 1 This is the lowest power IEC laser classification. Conformity is ensured through a software restriction of 120 seconds of laser operation within any 1000 second window and an automatic laser shutdown if the scanner's oscillating mirror fails. Intercharacter Gap The space between two adjacent bar code characters in a discrete code. Interleaved 2 of 5 A binary bar code symbology representing character pairs in groups of five bars and five interleaved spaces. Interleaving provides for greater information density. The location of wide elements (bar/spaces) within each group determines which characters are encoded. This continuous code type uses no intercharacter spaces. Only numeric (0 to 9) and START/STOP characters may be encoded. Interleaved Bar Code A bar code in which characters are paired together, using bars to represent the first character and the intervening spaces to represent the second. LASER - Light Amplification by Stimulated Emission of Radiation The laser is an intense light source. Light from a laser is all the same frequency, unlike the output of an incandescent bulb. Laser light is typically coherent and has a high energy density. Laser Diode A gallium-arsenide semiconductor type of laser connected to a power source to generate a laser beam. This laser type is a compact source of coherent light. Laser Scanner An optical bar code reading device using a coherent laser light beam as its source of illumination. LED Indicator A semiconductor diode (LED - Light Emitting Diode) used as an indicator, often in digital displays. The semiconductor uses applied voltage to produce light of a certain frequency determined by the semiconductor's particular chemical composition. Matrix Symbols A 2-dimensional array of regular polygon shaped cells where the center-to-center distance of adjacent elements is uniform. The arrangement of the cells represents data and/or symbology functions. Matrix symbols may include recognition patterns that do not follow the same rule as the other elements within the symbol (i.e., Data Matrix and MaxiCode). GL-9 GL-10 WLS 8400 Product Reference Guide MIL 1 mil = 1 thousandth of an inch; a unit of measure often used to quantify bar code printing and scanning dimensions. Misread (Misdecode) A condition which occurs when the data output of a reader or interface controller does not agree with the data encoded within a bar code symbol. Module (1) The narrowest nominal width unit of measure in a symbol. In certain symbologies, element widths are specified as multiples of 1 module. Equivalent to X dimension; or (2) a single cell in a matrix symbology used to encode 1 bit of data. In MaxiCode, the module shape is a regular hexagon. In Data Matrix, the module shape is nominally square. In PDF417, the module shape is a regular rectangle. In bar code symbologies, the module shape is a regular rectangle. Module Check Digit or Character A character within the symbol data field calculated using modular arithmetic that is used for error detection. The calculated character is determined by applying a code algorithm to the data field contents (see Check Digit). Moving Beam Bar Code Reader A device where scanning motion is achieved by mechanically moving the optical geometry. MRD Minimum reflectance difference: a formula that is used to determine if there is an adequate difference between absorbed and reflected light. Nanometer Unit of measure used to define the wavelength of light that is equal to 10-9 meter. Nominal The exact (or ideal) intended value for a specified parameter. Tolerances are specified as positive and negative deviations from this value. Nominal Size Standard size for a bar code symbol. Most UPC/EAN codes are used over a range of magnifications (e.g., from 0.80 to 2.00 of nominal). Non-Contact Reader/Scanner Bar code readers requiring no physical contact with the printed symbol. Non-read The absence of data at the scanner output after an attempted scan, which is due to no code, defective code, scanner failure or operator error. Glossary Omnidirectional Bar codes read in any orientation relative to the scanner. Optical Throw The distance from the scanner face to the closest point at which symbol can be read; also, optical throw is the difference between range and depth of field. Orientation The alignment of the symbol's scan path. Two possible orientations are horizontal with vertical bars and spaces (picket fence) and vertical with horizontal bars and spaces (ladder). Overhead The fixed number of characters required for start, stop and checking in a given symbol. For example, a symbol requiring a start, stop and 2 check characters contains 4 characters of overhead. Parameter A variable that can have different values assigned to it. PDF417 An error correcting 2-dimensional multi-row symbol developed in 1992 by Symbol Technologies, PDF417 symbols are constructed from 4 bars and 4 spaces over 17 modules. The symbol size is from 3 to 90 rows. There is no specified minimum or maximum for X or Y dimension. With at least the recommended minimum level of error correction, the recommended Y dimension is 3X. With less than the minimum recommended level of error correction, the recommended Y dimension is 4X. A quiet zone of 2X is specified on each side of a symbol. Because of delta decode techniques, the symbology is immune from uniform bar width growth. PDF417 supports cross-row scanning. The intellectual property rights associated with PDF417 have been committed to the public domain. Percent Decode The average probability that a single scan of a bar code would result in a successful decode. In a welldesigned bar code scanning system, that probability should approach near 100%. Pitch Rotation of a bar code symbol in an axis parallel to the direction of the bars. Plessey Code A pulse-width, modulated bar code commonly used for shelf marking in grocery stores. GL-11 GL-12 WLS 8400 Product Reference Guide Postnet Code Code developed by the U.S. Postal Service to assist in the automatic sorting of mail. Print Contrast Signal (PCS) Measurement of the contrast (brightness difference) between the bars and spaces of a symbol. A minimum PCS value is needed for a bar code symbol to be scannable. PCS = (RL - RD) / RL, where RL is the reflectance factor of the background and RD the reflectance factor of the dark bars. Programming Mode The state in which a scanner is configured for parameter values (see Scanning Mode). Quiet Zone A clear space, containing no dark marks, which precedes the start character of a bar code symbol and follows the stop character. Radio Frequency Non-optical automatic identification devices that use radio waves to transmit data. Radio Frequency Data Communication (RFDC) Handheld or vehicle mounted units that send and receive messages by radio frequency. Information from the units is displayed on a screen for workers and allows real-time, two-way exchange of data between terminals when one terminal is mobile and the other is a host computer at a remote location. Radio Frequency Identification (RFID) The use of small radio transponders that are activated by a reading transmitter. The transponder carries a unique ID code or other information in its memory and can be read at a distance without line of sight. Radio Frequency Tag An electronic tag capable of receiving, storing and/or transmitting digital information. Reflectance Amount of light returned from an illuminated surface. Resolution The narrowest element dimension which is distinguished by a particular reading device or printed with a particular device or method. RSS Reduced Space Symbology: A family of space efficient symbologies developed by UCC.EAN. Scan Area Area intended to contain a symbol. Glossary Scanner An electronic device used to scan bar code symbols and produce a digitized pattern that corresponds to the bars and spaces of the symbol. Its three main components are: 1. Light source (laser or photoelectric cell) illuminates a bar code. 2. Photodetector - registers the difference in reflected light (more light reflected from spaces). 3. Signal conditioning circuit - transforms optical detector output into a digitized bar pattern. Scanning Mode The scanner is energized, programmed, and ready to read a bar code. Scanning Sequence A method of programming or configuring parameters for a bar code reading system by scanning bar code menus. Self-Checking Code A symbology that uses a checking algorithm to detect encoding errors within the characters of a bar code symbol. Skew Rotation of a bar code symbol on an axis parallel to the symbol's length. Space The lighter element of a bar code formed by the background between bars. Space Width The thickness of a space measured from the edge closest to the symbol start character to the trailing edge of the same space. Specular Reflection The mirror-like direct reflection of light from a surface, which can cause difficulty decoding a bar code. Stacked Symbol (2D Symbols) A 2-dimensional (2D) symbol with sequences of linear (width-coded) data that are stacked one upon another (i.e., PDF417). Start/Stop Character A pattern of bars and spaces that provides the scanner with start and stop reading instructions and scanning direction. The start and stop characters are normally to the left and right margins of a horizontal code. Substrate A foundation material on which a substance or image is placed. GL-13 GL-14 WLS 8400 Product Reference Guide Symbol A scannable unit that encodes data within the conventions of a certain symbology, usually including start/stop characters, quiet zones, data characters, and check characters. Symbol Aspect Ratio The ratio of symbol height to symbol width. Symbol Density The number of data characters per unit length; usually expressed as characters per inch (CPI). Symbol Height The distance between the outside edges of the quiet zones of the first row and the last row. Symbol Length Length of symbol measured from the beginning of the quiet zone (margin) adjacent to the start character to the end of the quiet zone (margin) adjacent to a stop character. Symbology The structural rules and conventions for representing data within a particular bar code type (e.g. UPC/ EAN, Code 39). Tilt Rotation of a bar code symbol on an axis perpendicular to the substrate. Tolerance Allowable deviation from the nominal bar or space width. 2-dimensional (2D) symbology A machine-readable symbol which must be examined both vertically and horizontally to read the entire message. A 2D symbol may be one of two types of machine-readable symbols: a Matrix Symbol or a stacked symbol. 2D symbols differ from linear bar codes with the ability for high data content, small size, data efficiency and error correction capability. UCC Uniform Code Council: the organization that administers the U.P.C and other retail standards. UCC.EAN-128 Code 128 with a Function 1 character in the first position that is the symbology used with the UCC.EAN format for a universal product number (UPN). UPC Universal Product Code. A relatively complex numeric symbology. Each character consists of two bars and two spaces, each of which is any of four widths. The standard symbology for retail food packages in the United States. Glossary Variable Length Code A code with a number of encoded characters within a range, as opposed to a code with a fixed number of encoded characters. Vertical Bar Code A bar code pattern presented in such orientation that the symbol from start to stop is perpendicular to the horizon. The individual bars are in an array appearing as rungs of a ladder. Visible Laser Diode (VLD) A solid state device which produces visible laser light. Wedge A device that plugs in between a keyboard and a terminal and allows data to be entered by a keyboard or by various types of scanners. X Dimension The dimension of the narrowest bar and narrowest space in a bar code. Y Dimension The height of the modules in a row of a 2-dimensional symbols. GL-15 GL-16 WLS 8400 Product Reference Guide Index A actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-4 ADF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 actions . . . . . . . . . . . . . . . . . . . . 10-3, 10-28 move cursor . . . . . . . . . . . . . . . . 10-33 send data . . . . . . . . . . . . . . . . . . 10-28 setup fields . . . . . . . . . . . . . . . . . 10-32 alphanumeric keyboard . . . . . . . . . . 10-107 alternate rule sets . . . . . . . . . . . . . . . . . 10-5 bar code menu example . . . . . . . . . . . . 10-4 beep . . . . . . . . . . . . . . . . . . . . . . . . . . 10-53 code lengths . . . . . . . . . . . . . . . . . . . . 10-17 code types . . . . . . . . . . . . . . . . . . . . . 10-12 criteria . . . . . . . . . . . . . . . . . . . . 10-3, 10-12 default rules . . . . . . . . . . . . . . . . . . . . . 10-8 move cursor past a character . . . . . . . 10-32 move cursor to a character . . . . . . . . . 10-32 move cursor to start of data . . . . . . . . 10-32 numeric keypad . . . . . . . . . . . . . . . . . 10-25 pad spaces . . . . . . . . . . . . . . . . . . . . . 10-41 pad zeros . . . . . . . . . . . . . . . . . . . . . . 10-47 rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 rules hierarchy . . . . . . . . . . . . . . . . . . . 10-7 send alt characters . . . . . . . . . . . . . . . 10-76 send control characters . . . . . . . . . . . 10-54 send function key . . . . . . . . . . . . . . . . 10-88 send keyboard characters . . . . . . . . . . 10-60 send keypad characters . . . . . . . . . . . 10-82 send preset value . . . . . . . . . . . . . . . . 10-32 send value . . . . . . . . . . . . . . . . . . . . . 10-38 skip ahead characters . . . . . . . . . . . . . 10-34 skip ahead "n" characters . . . . . . . . . . 10-32 skip back characters . . . . . . . . . . . . . . 10-36 skip back "n" characters . . . . . . . . . . . 10-32 space removal . . . . . . . . . . . . . . . . . . 10-39 special commands . . . . . . . . . . . . . . . . 10-9 specific data string . . . . . . . . . . . . . . . 10-23 specific string Index-1 IN-2 WLS 8400 Product Reference Guide any location . . . . . . . . . . . . . . . . 10-24 any message ok . . . . . . . . . . . . . 10-24 at start . . . . . . . . . . . . . . . . . . . . . 10-23 rule belongs to set . . . . . . . . . . . 10-27 turn off rule sets . . . . . . . . . . . . . . . . 10-105 zero removal . . . . . . . . . . . . . . . . . . . 10-39 advanced data formatting . . . . . . . . . . . . . . . 10-3 actions . . . . . . . . . . . . . . . . . . . . 10-3, 10-28 alphanumeric keyboard . . . . . . . . . . 10-107 alternate rule sets . . . . . . . . . . . . . . . . . 10-5 bar code menu example . . . . . . . . . . . . 10-4 beep . . . . . . . . . . . . . . . . . . . . . . . . . . 10-53 code lengths . . . . . . . . . . . . . . . . . . . . 10-17 code types . . . . . . . . . . . . . . . . . . . . . 10-12 criteria . . . . . . . . . . . . . . . . . . . . 10-3, 10-12 default rules . . . . . . . . . . . . . . . . . . . . . 10-8 numeric keypad . . . . . . . . . . . . . . . . . 10-25 pad spaces . . . . . . . . . . . . . . . . . . . . . 10-41 pad zeros . . . . . . . . . . . . . . . . . . . . . . 10-47 rules . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 rules hierarchy . . . . . . . . . . . . . . . . . . . 10-7 send alt characters . . . . . . . . . . . . . . . 10-76 send control characters . . . . . . . . . . . . 10-54 send function key . . . . . . . . . . . . . . . . 10-88 send keyboard characters . . . . . . . . . . 10-60 send keypad characters . . . . . . . . . . . 10-82 send preset value . . . . . . . . . . . . . . . . 10-38 setup fields . . . . . . . . . . . . . . . . . . . . . 10-32 skip ahead characters . . . . . . . . . . . . . 10-34 skip back characters . . . . . . . . . . . . . . 10-36 space removal . . . . . . . . . . . . . . . . . . 10-39 special commands . . . . . . . . . . . . . . . . 10-9 specific data string . . . . . . . . . . . . . . . 10-23 turn off rule sets . . . . . . . . . . . . . . . . 10-105 zero removal . . . . . . . . . . . . . . . . . . . 10-39 aiming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 ASCII Values . . . . . . . . . . . . . . . . . . . . . . . . 6-26 B bar codes beep after good decode . . . . . . . . . . . . . 4-8 beeper tone . . . . . . . . . . . . . . . . . . . . . . . 4-5 beeper volume . . . . . . . . . . . . . . . . . . . . 4-6 data options pause duration . . . . . . . . . . . . . . . 10-9 prefix/suffix values . . . . . . . . . . . . 9-6 transmit code ID character . . . . . . . 9-5 interleaved 2 of 5 . . . . . . . . . . . . . . . . . 8-38 convert to EAN-13 . . . . . . . . . . . . 8-42 lengths . . . . . . . . . . . . . . . . . . . . . 8-38 keyboard wedge alternate numeric keypad emulation 5-12 caps lock on . . . . . . . . . . . . . . . . . 5-12 capsl ock override . . . . . . . . . . . . 5-13 country keyboard types (country codes) 58 default table . . . . . . . . . . . . . . . . . . 5-5 host types . . . . . . . . . . . . . . . . . . . . 5-7 ignore unknown characters . . . . . 5-10 intra-keystroke delay . . . . . . . . . . 5-11 keystroke delay . . . . . . . . . . . . . . 5-10 laser on time . . . . . . . . . . . . . . . . . . . . . . 4-7 miscellaneous scan data options . . . . . . . . . . . . . . 9-7 transmit no read msg . . . . . . . . . . . 9-9 numeric bar codes . . . . . . . . . . . . . . . . . D-7 RS-232 baud rate . . . . . . . . . . . . . . . . . . . . 6-10 Data Bits . . . . . . . . . . . . . . . . . . . 6-14 default table . . . . . . . . . . . . . . . . . . 6-5 hardware handshaking . . . . . . . . . 6-15 host serial response time-out . . . . 6-20 host types . . . . . . . . . . . . . . . . . . . . 6-9 intercharacter delay . . . . . . . . . . . 6-23 RTS line state . . . . . . . . . . . . . . . . 6-21 stop bit select . . . . . . . . . . . . . . . . 6-22 RS-232 parameters check receive errors . . . . . . . . . . . 6-13 parity . . . . . . . . . . . . . . . . . . . . . . 6-12 software handshaking . . . . . . . . . 6-18 RS-232C beep on bel . . . . . . . . . . . . . . . . . . 6-22 set defaults . . . . . . . . . . . . . . . . . . . . . . . 4-5 symbologies bi-directional redundancy . . . . . . 8-60 bookland EAN . . . . . . . . . . . . . . . 8-12 codabar . . . . . . . . . . . . . . . . . . . . . 8-46 Index codabar CLSI editing . . . . . . . . . . 8-49 codabar lengths . . . . . . . . . . . . . . 8-47 codabar NOTIS editing . . . . . . . . 8-49 code 11 . . . . . . . . . . . . . . . . . . . . . 8-34 code 11 lengths . . . . . . . . . . . . . . 8-34 code 128 . . . . . . . . . . . . . . . . . . . . 8-22 code 39 . . . . . . . . . . . . . . . . . . . . . 8-24 code 39 check digit verification . . 8-29 code 39 full ASCII . . . . . . . . . . . . 8-31 code 39 lengths . . . . . . . . . . . . . . 8-27 code 39 transmit check digit . . . . 8-30 code 93 . . . . . . . . . . . . . . . . . . . . . 8-32 code 93 lengths . . . . . . . . . . . . . . 8-32 convert UPC-E to UPC-A . . . . . . 8-20 convert UPC-E1 to UPC-A . . . . . 8-21 default table . . . . . . . . . . . . . . . . . . 8-6 discrete 2 of 5 . . . . . . . . . . . . . . . . 8-44 discrete 2 of 5 lengths . . . . . . . . . 8-44 EAN zero extend . . . . . . . . . . . . . 8-22 EAN-13 . . . . . . . . . . . . . . . . . . . . 8-11 EAN-8 . . . . . . . . . . . . . . . . . . . . . 8-12 I 2 of 5 check digit verification . . 8-41 I 2 of 5 convert to EAN-13 . . . . . 8-42 I 2 of 5 transmit check digit . . . . . 8-42 ISBT 128 . . . . . . . . . . . . . . . . . . . 8-23 MSI . . . . . . . . . . . . . . . . . . . . . . . 8-50 MSI check digit algorithm . . . . . . 8-53 MSI check digits . . . . . . . . . . . . . 8-52 MSI lengths . . . . . . . . . . . . . . . . . 8-50 MSI transmit check digit . . . . . . . 8-53 supplementals . . . . . . . . . . . . . . . . 8-13 UCC/EAN-128 . . . . . . . . . . . . . . . 8-23 UPC-A . . . . . . . . . . . . . . . . . . . . . 8-10 UPC-A preamble . . . . . . . . . . . . . 8-17 UPC-A/E/E1 check digit . . . . . . . 8-15 UPC-E . . . . . . . . . . . . . . . . . . . . . 8-10 UPC-E preamble . . . . . . . . . . . . . 8-18 UPC-E1 . . . . . . . . . . . . . . . . . . . . 8-11 transmit code ID . . . . . . . . . . . . . . . . . . . 9-5 UPC/EAN supp redundancy . . . . . . . . . . . . . 8-15 UPC/EAN/JAN supplemental redundancy . . . . . . 8-15 USB caps lock override . . . . . . . . . . . . 7-11 country keyboard types . . . . . . . . . 7-8 default table . . . . . . . . . . . . . . . . . . 7-6 device type . . . . . . . . . . . . . . . . . . . 7-7 keystroke delay . . . . . . . . . . . . . . 7-10 unknown characters . . . . . . . . . . . 7-12 C cables installing . . . . . . . . . . . . . . . . . . . . . . . . 1-5 interface . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 removing cables . . . . . . . . . . . . . . . . . . . 1-7 Caption Bar Code Normal Operation . . . . . . . . . . . . . . . . 6-24 Send Bar Code . . . . . . . . . . . . . . . . . . . 6-25 Character Set . . . . . . . . . . . . . . . . . . . . . . . . 6-26 codabar bar codes CLSI editing . . . . . . . . . . . . . . . . . . . . . 8-49 codabar . . . . . . . . . . . . . . . . . . . . . . . . . 8-46 lengths . . . . . . . . . . . . . . . . . . . . . . . . . 8-47 NOTIS editing . . . . . . . . . . . . . . . . . . . 8-49 code 11 bar codes code 11 . . . . . . . . . . . . . . . . . . . . . . . . . 8-34 lengths . . . . . . . . . . . . . . . . . . . . . . . . . 8-34 code 128 bar codes code 128 . . . . . . . . . . . . . . . . . . . . . . . . 8-22 UCC/EAN-128 . . . . . . . . . . . . . . . . . . 8-23 code 39 bar codes check digit verification . . . . . . . . . . . . 8-29 code 39 . . . . . . . . . . . . . . . . . . . . . . . . . 8-24 full ASCII . . . . . . . . . . . . . . . . . . . . . . 8-31 lengths . . . . . . . . . . . . . . . . . . . . . . . . . 8-27 transmit check digit . . . . . . . . . . . . . . . 8-30 code 93 bar codes code 93 . . . . . . . . . . . . . . . . . . . . . . . . . 8-32 lengths . . . . . . . . . . . . . . . . . . . . . . . . . 8-32 code identifiers AIM code IDs . . . . . . . . . . . . . . . . . . . . B-4 code types ADF . . . . . . . . . . . . . . . . . . . . . . . . . . 10-12 connecting power . . . . . . . . . . . . . . . . . . . . . . 1-6 IN-3 IN-4 WLS 8400 Product Reference Guide D decode zone . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9 default parameters . . . . . . . . . . . . . . . . . . . . . 4-4 keyboard wedge . . . . . . . . . . . . . . . . . . . 5-5 miscellaneous scanner options . . . . . . . . 9-4 RS-232 . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5 standard default table . . . . . . . . . . . . . . . A-3 symbologies . . . . . . . . . . . . . . . . . . . . . . 8-6 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6 user preferences . . . . . . . . . . . . . . . . . . . 4-4 discrete 2 of 5 bar codes discrete 2 of 5 . . . . . . . . . . . . . . . . . . . . 8-44 lengths . . . . . . . . . . . . . . . . . . . . . . . . . 8-44 H host types keyboard wedge . . . . . . . . . . . . . . . . . . . 5-7 RS-232 . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9 I information, service . . . . . . . . . . . . . . . . . . . . .xvi interleaved 2 of 5 bar codes check digit verification . . . . . . . . . . . . 8-41 convert to EAN-13 . . . . . . . . . . . . . . . . 8-42 transmit check digit . . . . . . . . . . . . . . . 8-42 ISBT 128 bar codes ISBT 128 . . . . . . . . . . . . . . . . . . . . . . . 8-23 K keyboard wedge connection . . . . . . . . . . . . . . 5-4 keyboard wedge default parameters . . . . . . . 5-5 keyboard wedge parameters . . . . . . . . . . . . . . 5-7 M maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 miscellaneous scanner parameters . . . . . . . . . 9-4 MSI bar codes check digit algorithm . . . . . . . . . . . . . . 8-53 check digits . . . . . . . . . . . . . . . . . . . . . 8-52 lengths . . . . . . . . . . . . . . . . . . . . . . . . . 8-50 MSI . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-50 transmit check digit . . . . . . . . . . . . . . . 8-53 N notational conventions . . . . . . . . . . . . . . . . . . .xvi P parameters keyboard wedge . . . . . . . . . . . . . . . . . . . RS-232 . . . . . . . . . . . . . . . . . . . . . . . . . . USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . pinouts scanner signal descriptions . . . . . . . . . . power supply connecting . . . . . . . . . . . . . . . . . . . . . . . 5-7 6-6 7-7 3-9 1-6 R RS-232 connection . . . . . . . . . . . . . . . . . . . . . 6-4 RS-232 default parameters . . . . . . . . . . . . . . 6-5 RS-232 parameters . . . . . . . . . . . . . . . . . . 6-6, 6-9 RSS Convert RSS to UPC/EAN . . . . . . . . . 8-55 S scanner defaults . . . . . . . . . . . . . . . . . . . . . . . 4-4 scanning aiming . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 errors . . . . . . . . . . . . . . . . . . . . 4-3, 8-5, 9-4 hand-held . . . . . . . . . . . . . . . . . . . . . . . . 2-6 hands-free . . . . . . . . . . . . . . . . . . . . . . . 2-8 sequence example . . . . . . . . . . 4-3, 8-5, 9-4 security level bar codes bi-directional redundancy . . . . . . . . . . 8-60 service information . . . . . . . . . . . . . . . . . . . . .xvi setup connecting a USB interface . . . . . . . . . . 7-4 connecting an RS-232 interface . . . . . . . 6-4 connecting interface cable . . . . . . . . . . . 1-6 connecting keyboard wedge interface . . 5-4 connecting power . . . . . . . . . . . . . . . . . . 1-6 connecting power supply . . . . . . . . . . . . 1-6 installing the cable . . . . . . . . . . . . . . . . . 1-5 unpacking . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Index signal descriptions . . . . . . . . . . . . . . . . . . . . . 3-9 specifications . . . . . . . . . . . . . . . . . . . . . . . . . 3-7 standard default parameters . . . . . . . . . . . . . . A-3 standard defaults . . . . . . . . . . . . . . . . . . . . . . 4-4 symbol support center . . . . . . . . . . . . . . . . . . xvii symbology default parameters . . . . . . . . . . . . 8-6 T technical specifications . . . . . . . . . . . . . . . . . 3-7 U unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 UPC/EAN bar codes bookland EAN . . . . . . . . . . . . . . . . . . . 8-12 check digit . . . . . . . . . . . . . . . . . . . . . . 8-15 convert UPC-E to UPC-A . . . . . . . . . . 8-20 convert UPC-E1 to UPC-A . . . . . . . . . 8-21 EAN zero extend . . . . . . . . . . . . . . . . . 8-22 EAN-13 . . . . . . . . . . . . . . . . . . . . . . . . 8-11 EAN-8 . . . . . . . . . . . . . . . . . . . . . . . . . 8-12 UPC-A . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 UPC-A preamble . . . . . . . . . . . . . . . . . 8-17 UPC-E . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 UPC-E preamble . . . . . . . . . . . . . . . . . 8-18 UPC-E1 . . . . . . . . . . . . . . . . . . . . . . . . 8-11 UPC/EAN/JAN bar codes supplementals . . . . . . . . . . . . . . . . . . . 8-13 USB connection . . . . . . . . . . . . . . . . . . . . . . . 7-4 USB default parameters . . . . . . . . . . . . . . . . . 7-6 USB parameters . . . . . . . . . . . . . . . . . . . . . . . 7-7 user preferences parameters . . . . . . . . . . . . . . 4-4 IN-5 IN-6 WLS 8400 Product Reference Guide 72-67133-01 Revision A — February 2004
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : Yes Page Count : 394 Page Mode : UseOutlines XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:638343ae-ba61-4746-a71c-aa7aa346d340 Producer : Acrobat Distiller 6.0.1 (Windows) Creator Tool : FrameMaker 7.1 Modify Date : 2005:03:07 12:20:20Z Create Date : 2005:03:07 12:20:20Z Document ID : uuid:12e6600e-0909-4014-a987-7bf2432bbf4b Format : application/pdf Title : NGIS.book Creator : WaspTester Author : WaspTesterEXIF Metadata provided by EXIF.tools