WaveIP GA24 Outdoor Transmitter Unit User Manual User Guide
WaveIP Ltd. Outdoor Transmitter Unit User Guide
WaveIP >
Users Manual Revised 031903
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 312319 |
| Application ID | B9rjHAUtDRHJ70nfE6Jvlg== |
| Document Description | Users Manual Revised 031903 |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 108.45kB (1355686 bits) |
| Date Submitted | 2003-03-21 00:00:00 |
| Date Available | 2003-03-17 00:00:00 |
| Creation Date | 2003-03-19 12:43:05 |
| Producing Software | Acrobat PDFWriter 4.05 for Windows NT |
| Document Lastmod | 2003-03-21 20:24:41 |
| Document Title | User Guide.PDF |
| Document Creator | User Guide.doc (Read-Only) - Microsoft Word |
| Document Author: | AmitA |
GigAccessTM - User Guide Installation and Operation Instructions PRELIMINARY February 2003 Rev A February 2003 Rev. A Table of Contents 1. INTRODUCTION ........................................................................................................... 7 1.1. GENERAL............................................................................................................................. 7 1.2. GIGACCESSTM SYSTEM OVERVIEW ...................................................................................... 7 1.3. THE AU/SU OUTDOOR UNIT GENERAL DESCRIPTION ........................................................... 10 2. INSTALLATION .......................................................................................................... 11 2.1. PACKING LIST .................................................................................................................... 11 2.2. ADDITIONAL PART LIST – REQUIRED FOR INSTALLATION ....................................................... 12 2.3. INSTALLATION OVERVIEW ................................................................................................... 12 2.4. AU/SU OUTDOOR INSTALLATION ........................................................................................ 14 2.4.1. Site Selection............................................................................................................. 14 2.4.2. Mounting and Wiring.................................................................................................. 16 2.4.3. Antennas ................................................................................................................... 17 2.4.4. Sealing ...................................................................................................................... 20 2.5. SUBSCRIBER PC SETUP ..................................................................................................... 21 2.6. INDOOR OUTLET INSTALLATION ........................................................................................... 22 2.6.1. Indoor Outlet.............................................................................................................. 22 2.6.2. Cables ....................................................................................................................... 23 2.6.3. Grounding.................................................................................................................. 26 2.6.4. Consecutive Connection ............................................................................................ 27 3. GIGACCESSTM 2.4 TECHNICAL SPECIFICATIONS................................................ 28 3.1. GENERAL SPECIFICATION ................................................................................................... 28 3.2. BASE STATION - ACCESS UNIT (OUTDOOR) .......................................................................... 28 3.3. HIGH PERFORMANCE SUBSCRIBER UNIT (OUTDOOR) ............................................................ 29 3.4. RADIO SPECIFICATIONS ...................................................................................................... 30 3.5. MANAGEMENT NMS ........................................................................................................... 30 4. APPENDIX A – WAVEIP APPROVED ANTENNAS ................................................... 31 5. APPENDIX B: CALCULATION RF LINK BUDGET.................................................... 32 6. APPENDIX C – MAX RF POWER AND DISTANCE VERSUS ANTENNA GAIN .............................................................................................................................. 34 7. APPENDIX D: RF HAZARD DISTANCE CALCULATION .......................................... 36 8. APPENDIX E – RF CHANNEL LIST ........................................................................... 38 9. APPENDIX F – OUTDOOR CABLES SCHEME ......................................................... 39 10. APPENDIX G - USING THE UNIT MANAGER TOOL ............................................. 40 10.1. GENERAL......................................................................................................................... 40 10.2. MENU COMMANDS............................................................................................................ 40 10.2.1. Selecting adapter..................................................................................................... 40 10.3. TOOLBAR COMMANDS ...................................................................................................... 41 10.3.1. Start Session ........................................................................................................... 41 10.3.2. End Session ............................................................................................................ 41 10.3.3. Refresh Unit Parameters ......................................................................................... 41 10.3.4. Auto Reconnect ....................................................................................................... 41 10.3.5. Start Logger............................................................................................................. 41 10.3.6. Stop Logger ............................................................................................................. 42 10.3.7. Clear Log ................................................................................................................. 42 Page 3 of 47 February 2003 Rev. A 10.3.8. Log to File ................................................................................................................42 10.3.9. View Log ..................................................................................................................42 10.3.10. Reset Text .............................................................................................................42 10.4. INSTALLATION W INDOW ....................................................................................................42 10.4.1. Advanced Window ...................................................................................................44 10.5. BOOT W INDOW ................................................................................................................45 10.6. SOFTWARE WINDOW ........................................................................................................46 10.6.1. General....................................................................................................................46 10.6.2. Firmware Window ....................................................................................................46 10.6.3. PLD Window ............................................................................................................47 10.6.4. PHY Window............................................................................................................47 Page 4 of 47 February 2003 Rev. A Table of Figures Figure 1-1: General Description of typical sector in GigAccess™ System ......................................7 Figure 1-2: GigAccess™ Outdoor Unit............................................................................................8 Figure 1-3: Consecutive Sector principle ........................................................................................9 Figure 1-4: Outdoor Unit Block Diagram .......................................................................................10 Figure 2-1: General System View .................................................................................................11 Figure 2-2: GigAccess™ - General Installation Scheme ...............................................................13 Figure 2-3: Wall mount description ...............................................................................................16 Figure 2-4: Indoor Outlet – Metal Model ......................................................................................22 Figure 2-5: Power Supply for Indoor Outlet (This picture is for illustration only! ) .........................................22 Figure 2-6: Cable preparation for Outdoor Unit............................................................................23 Figure 2-7: Cable assembly to Outdoor Unit .................................................................................24 Figure 2-8: Cable insertion to Outdoor Unit. .................................................................................24 Figure 2-9: Cable connection to Outdoor Unit..............................................................................25 Figure 2-10: Cable connection to Indoor Outlet ...........................................................................25 Figure 2-11: Ground Connection to Outdoor Unit .........................................................................26 Figure 5-1: Radio Link – General description................................................................................32 Figure 9-1: Outdoor Cables Scheme ............................................................................................39 Figure 10-1: Adapter Selection Window in Unit Manager Tool......................................................40 Figure 10-2: Discover Window in Unit Manager Tool ....................................................................41 Figure 10-3: Installation Window in Unit Manager Tool.................................................................42 Figure 10-4: Advanced Window in Unit Manager Tool ..................................................................44 Figure 10-5: Boot Window in Unit Manager Tool ..........................................................................45 Figure 10-6: Software Window in Unit Manager Tool....................................................................46 Figure 10-7: Firmware Window in Unit Manager Tool ...................................................................46 Figure 10-8: PLD Window in Unit Manager Tool...........................................................................47 Figure 10-9: PHY Window in Unit Manager Tool ..........................................................................47 Page 5 of 47 February 2003 Rev. A Table of Tables Table 2-1: Regulatory Domain Specification ................................................................................ 14 Table 4-1: Integrated Antennas for GigAccess™ ......................................................................... 31 Table 4-2: Detached Antennas for GigAccess™.......................................................................... 31 Table 6-1: Max RF Power and Distance for FCC in point-to-multi-point ....................................... 34 Table 6-2: Max RF Power and Distance for FCC in point-to-point................................................ 35 Table 6-3: Max RF Power and Distance for ETSI......................................................................... 35 Table 7-1: Hazard Distance versus Antenna Gain for Point to Multi Point.................................... 37 Table 7-2: Hazard Distance versus Antenna Gain for Point to Point ............................................ 37 Table 8-1: RF channel List ........................................................................................................... 38 Page 6 of 47 February 2003 Rev. A 1. Introduction 1.1. General The information contained in this manual provides GigAccessTM system overview and instructions for Planning, Installation, Configuration, and Operation of both the Access Units, the Subscriber Units including antennas and accessories. 1.2. GigAccessTM System Overview GigAccessTM is WaveIP’s wireless point-to-point and point-to-multipoint broadband communication system. The basic subsystem is composed of a single sector, which consists of an AU (Access Unit) and up to 64 SUs (Subscriber Units). Each sector is a stand-alone communication network operating on a star topology with a gateway to the WAN, which allows two-way communication between the SUs and the WAN via the AU. A Sector may be divided into sub sectors, which are consecutive to the SUs within the sector. A sector may include a BC (Base Controller) as an option. The BC is based on a PC and is connecting to the AUs via the Ethernet. The interface to the BC is a 10/100 BASE-T, Ethernet port, which provide an NMS (Network Management System) that can be integrated through an SNMP interface to high level NMS of the service provider . Its main purpose is to configure the AUs and SUs with SLA (Service Level Agreement). Once the AU was configured, the configuration file is burned into an internal FLASH memory and the AU can run autonomic without the need of a BC (stand alone configuration). Figure 1-1 depicts a general description of a typical sector in the GigAccess™ system. WAN SU SU AU Switch/Router Base Controller (Option) SU AU SU Figure 1-1: General Description of typical sector in GigAccess™ System The sector uses a single radio channel frequency that carries up to 11 MBPS of data throughput. The data bandwidth is divided between the traffic from the AU to SUs (downstream) and the traffic from the SUs to AU (upstream). GigAccess™ utilizes Time Domain Duplex (TDD) technique in Page 7 of 47 February 2003 Rev. A order to divide the bandwidth periodically, based on FRAME SIZE. The portion of the frame, which is allocated to the upstream traffic between the SUs, is TDMA (Time Division Multiplex Access) time domain technique. It is controlled dynamically and allows a very efficient way of channel capacity utilization. A small portion of the capacity is allocated for new SU registration. The registration slot is allocated to the SU based on slotted aloha algorithm. Figure 1-2: GigAccess™ Outdoor Unit The GigAccessTM MAC layer is based on IEEE 802.16 MAC standard with additional proprietary attributes, which allow some special features such as Consecutive APTM. GigAccessTM networking enables routing and QoS (Quality of Service) queuing of traffic, based on classification of packets information in layer 2, 3 & 4. In certain instances QoS queuing can be done using packet information (priority defined by the management). Operating in the unlicensed 2.4 GHz frequency band, GigAccessTM 2.4 leverages Direct Sequence Spread Spectrum (DSSS) technology to deliver high data rates, high spectral efficiency in addition to immunity to interference and line of site boundaries via patent pending consecutiveAP™ technology. GigAccessTM 2.4 ensures always-on connectivity to full range of IP-based services, including fast Internet streaming video and VOIP. GigAccessTM 2.4 provides an independent infrastructure, which is easy to deploy with very low operating costs. Page 8 of 47 February 2003 Rev. A In case of NLOS (Non Line of Sight) between the AU and the SU due to obstacles such as tall buildings or mountains, a consecutive sector can be used. In this case the SU Ethernet output feed a consecutive AU, which acts as a repeater to bypass the obstacle as shown in Figure 1-3. Up to 100m Ethernet + Power Cable Consecutive AU Channel 2 Channel 2 Channel 1 Channel 1 SU Ethernet to local Ethernet users to local users AU Building SU Figure 1-3: Consecutive Sector principle Page 9 of 47 February 2003 Rev. A 1.3. The AU/SU Outdoor Unit General Description SDRAM 132Mhz power and data port1 data power and data port2 Ethernet Block 25Mhz Crystal data Digital Block PHY Block 44Mhz Oscilator IF Block Filter 374Mhz RF Block Synthesizer Synthesizer (741 - 755 Mhz) (2035- 2125 Mhz) Operate Fixed : 748Mhz Operating Range : 2038 - 2110 Mhz RF OUTPUT CH00 = 2.412Ghz CH01 = 2.417Ghz CH02 = 2.422Ghz CH03 = 2.427Ghz CH04 = 2.432Ghz CH05 = 2.437Ghz CH06 = 2.442Ghz CH07 = 2.447Ghz CH08 = 2.452Ghz CH09 = 2.457Ghz CH10 = 2.462Ghz CH11 = 2.467Ghz CH12 = 2.472Ghz Frequency Control Figure 1-4: Outdoor Unit Block Diagram The outdoor unit (AU/SU) is composed from the following blocks: • Ethernet interface – 2 RJ 45 connectors for Ethernet interfaces compliant with Ethernet/IEEE 802.3 and the power (48 VDC). This block consists of an Ethernet PHY, Ethernet switch and Ethernet MAC. • Digital Block – consists of the main HW control logic, the CPU and it peripherals like memories (RAM, DDR, Flash), Timers, Interrupt controller, UART etc. • PHY Block – consists of a PHY11B based around INTERSIL Direct Sequence Spread Spectrum Base-band processor. • RF/IF Block - Consists of the Modulator/Demodulator and Synthesizer + RF IF converter and synthesizer based on INTERSIL Prism2 chipset. Page 10 of 47 February 2003 Rev. A 2. Installation 2.1. Packing List When you first open the package, verify that the unit is complete with the following components: • AU or SU Outdoor Unit • • Indoor Outlet. • Indoor Power Supply (AC input). • Pole mounting kit. • Sealing grommet and cap and clamping plates. Outdoor Unit with 13.5 dBi Indoor Outlet Integrated Antenna Pole Mounting Kit Outdoor Unit with 15.5 dBi Integrated Antenna Indoor Power Supply Figure 2-1: General System View Page 11 of 47 February 2003 Rev. A 2.2. Additional Part List – Required for Installation • Outdoor Unit grounding cable • Indoor Outlet grounding cable (for metal Indoor Outlet only!). • Outdoor-to-Indoor CAT5 shielded cable (Up to 90 meters). • Indoor CAT5 cable. • RJ45 - Installation KIT. • RJ45 - Crimping tool. • Adjustable wrench + screwdriver. 2.3. Installation Overview This section provides installation information for GigAccess™ 2.4 system. This device can be expected to comply with Part 15 of the FCC Rules provided it is assembled in accordance with the instructions provided in this document. Note: Outdoor units and antennas should be installed ONLY by experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities. Failure to do so may void the GigAccess™ product warranty and may expose the end user or the service provider to legal and financial liabilities. WaveIP and its resellers or distributors are not liable for injury, damage or violation of regulations associated with the installation of outdoor units or antennas. A typical installation scheme is depicted in Figure 2-2. The installation process should follow the following steps: 1) Select the appropriate location for the Outdoor unit and the indoor Outlet. 2) Mount the Outdoor unit. If you are using detached antenna mount the antenna and connect it to the Outdoor unit. Page 12 of 47 February 2003 Rev. A AU/SU - Outdoor Unit w ith integral Antenna 48VDC + Ethernet (CAT 5) Indoor Outlet 48V DC 100-240V AC AC/DC Power Supply Ethernet Data Cable CAT5 User computer Figure 2-2: GigAccess™ - General Installation Scheme WARNING: It is the responsibility of the installer to insure that when using the outdoor antenna kits in the United States (or where FCC rules apply), only those antennas certified with the product are used. The use of any antenna other than those certified with the product is expressly forbidden in accordance to FCC rules part 15.247 The installer should configure the output power level of antennas, according to country regulations and per antenna type. 3) Connect a ground cable between the Outdoor unit and an appropriate grounding point. 4) Connect the Outdoor-to-Indoor CAT5 shielded cable to the Outdoor unit and route it to the location selected for the Indoor Outlet. Assemble the enclosed connector on the cable. 5) Mount the Indoor Outlet. 6) Connect the Outdoor-to-Indoor cable to the Indoor Outlet Radio port. (This port supplies 48 VDC in addition to the Ethernet data). 7) Connect the CAT5 Ethernet cable from the user’s network/PC to the Indoor Outlet data port. 8) Connect the power supply to the Indoor Outlet power port. 9) Align the antenna and verify connectivity of the Outdoor as follows: • For SU check connectivity to the base controller. • For AU check connectivity to the SU management IP address. The connectivity can be checked by using the ping instruction. Page 13 of 47 February 2003 Rev. A 2.4. AU/SU Outdoor Installation 2.4.1. Site Selection 2.4.1.1. Access Unit (AU) Location of the Access Unit is on the Service Provider sole discretion considering local topology and the desired cover. One (in case of Omni antenna) or several AUs (in case of directional antenna) forms the BS (Base-Station) – the central of a cell. The placement of AUs should be such that cells overlap slightly, to guarantee seamless wireless connectivity everywhere. Neighboring AUs should preferably send and receive on different channels or different polarization for maximum throughput (minimum interference). The radio channels depend on the regulations in your area. Table 2-1 provides the specifications for main regulatory domains: Region Regulatory Domain Relevant Radio Channels USA FCC 0 – 12 Canada DOC 0 – 12 Europe ETSI 0 - 12 Spain SPAIN 10 France FRANCE 10 (Except Spain and France) Table 2-1: Regulatory Domain Specification For channel frequency list see Table 8-1 in Appendix E – RF Channel List This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 2.4.1.2. Subscriber Unit (SU) Location of the Subscriber Unit must take into consideration the following guidelines: • Clear line of site to the AU. • Height above the ground. • Distance between sites. Path of Clearest Propagation A propagation path is the path that signals traverse between the antennas of any two bridges. The “line” between two antenna sites is an imaginary straight line, which may be drawn Page 14 of 47 February 2003 Rev. A between the two antennas. Any obstacles in the path of the “line” degrade the propagation path. The best propagation path is, therefore, a clear line of sight with good clearance between the “line” and any physical obstacle. Physical Obstacles Any physical object in the path between Au and SU can cause signal attenuation. Common obstructions are buildings and trees. Any buildings or other physical structure such as trees, mountains or other natural geographic features higher than the antenna and situated in the path between the two sites can constitute obstructions. Install outdoor antennas high enough to avoid any obstacles, which may block the signal. Minimal Path Loss Path loss is determined mainly by several factors: • Distance between sites – Path loss is lower and system performance better when distances between sites are shorter. • Clearance – Path loss is minimized when there exists a clear line of sight. The number, location, size, and makeup of obstacles determine their contribution to path loss. • Antenna height – Path loss is lower when antennas are positioned higher. Antenna height is the distance from the imaginary line connecting the antennas at the two sites to “ground” level. “Ground” level in an open area is the actual ground. In dense urban areas, “ground” level is the average height of the buildings between the antenna sites. Page 15 of 47 February 2003 Rev. A 2.4.2. Mounting and Wiring Outdoor Unit mounting and installation will be performed only by personal licensed to install rooftop antenna equipment where such license required by the regulation authorities. On any installation case, only professional antenna installers will perform Outdoor Unit mounting and installation. Outdoor Unit can be mount on a pole or on a wall. A general description of wall mount is given in Figure 2-3. Figure 2-3: Wall mount description WARNING! When using the system for point-to-multi-point all outdoor units must be installed with a separation distance of at least 20 cm. For a base station or any installation consisting of more than one outdoor unit (AU or SU) the safety distance for all persons should be at least 2 meters. When using the system for point to point (p2p) applications all outdoor units must be installed with a separation distance of at least 2 meters from all persons during normal operation For detailed calculation see: Appendix D: RF Hazard Distance Calculation on page 36 Page 16 of 47 February 2003 Rev. A 2.4.3. Antennas 2.4.3.1. General Two types of antennas are available for the GigAccess™ system: • Integrated antenna • Detached antenna The necessary antenna gain depends on the required range and performance. IMPORTANT! Antennas must be selected from a list of WaveIP approved antennas. See Appendix A – WaveIP Approved Antennas, page 31 for list. According to FCC part 15.247(b): (1) “The maximum peak output power of intentional radiator shall not exceed 1 Watt” (+30 dBm). (2) “If transmitting antennas of directional gain greater than 6 dBi are used, the peak output power from the intentional radiator shall be reduced below the maximum peak power (of +30 dBm) as appropriate, by the amount in dB that the directional gain of antenna exceeds 6 dBi”. That is to say that the maximum EIRP (Effective Isotropic Radiated Power) shall not exceed +36 dBm. (3) “Systems operating in the 2400-2483.5 Mhz band that are used exclusively for fixed, point-topoint operations may employ transmitting antennas with directional gain greater than 6 dBi provided the maximum peak output power of intentional radiator is reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6 dBi”. WARNING! To comply with the FCC 15.247(b)(4)(iii), the equipment should be professionally installed. The installer is responsible for ensuring that the system is used exclusively for fixed, point-to-point operation! WARNING! It is the installer responsibility that when using approved parabolic dish antennas in point-to-point operations, that they may not be co-located with other intentional radiators transmitting the same information. Page 17 of 47 February 2003 Rev. A According to ETSI: (1) The maximum EIRP shall not exceed +20 dBm (100 mWatt). IMPORTANT! To comply with the FCC/ETSI EIRP limits, the outdoor unit-transmit power need to be adjusting according to the installed antenna gain. Therefore a professional installation of the transmitter is required. The outdoor unit must be configured at the time of installation by qualified personal. Fail to comply with FCC rules may expose the installer to legal liabilities. For open outdoor areas with clear line of sight between the SU and the AU the suggested maximum distance is given in Appendix C – Max RF Power and Distance versus Antenna Gain. 2.4.3.2. Detached Antenna Operating with detached antenna allowed only after outdoor unit power setup is confirmed not to exceed +36 dBm EIRP for USA for point-to-multi-point operation or +20 dBm EIRP for Europe for any antenna used. For point-to-point operation the EIRP can exceeds +36dBm and therefore it must be configured by a professional installer. The configuration is only allowed by password of administrator privilege. The outdoor unit transmit power configuration is done by the Unit Manager Tool. The tool consists of dedicated software running on a PC. This PC communicates with the outdoors unit via the Ethernet and is used to burn the configuration parameters (including the transmit power) into the outdoor unit internal FLASH. The tool limits the max transmit power according to the selected antenna, the selected regulation (FCC/ETSI) and the selected link type (point-to-multi-point/pointto-point). Of course the installer, if needed can select a lower power. For example: if the selected antenna gain is 24 dBi, the regulation is FCC and the link type is point-to-multi-point, the tool will set the maximum transmitted power (before the antenna) to +12 dBm (so that EIRP will not exceeds +36dBm). The Unit Manager Tool supports two levels of privilege password: regular user and administrator user. Since power output levels will affect compliance of the unit with FCC / ETSI rules, precautions are built into the system to keep the end user from adjusting the power output level above the regulation limits. Therefore: • Antenna type (detached or integrated) • Antenna gain • Tx Power • Regulation (FCC or ETSI) • Link Type (point-to-multi-point or point-to-point) Configuration is only allowed by password of administrator privilege. The above configuration is done with the advanced window of the Unit Manager Tool - see paragraph 10.4.1. For detailed description of how to use the Unit Manager tool See Appendix G Using the Unit Manager Tool, on page 40. Page 18 of 47 February 2003 Rev. A The GigAccess™ was designed to work with co-located antennas. That means that two antennas can be connected. The minimum distance between the two antennas should be 20 cm. The two antennas should be of the same type (Directional Flat Panel Antenna, or Base Station Antenna or Parabolic Dish). The main idea is to utilize two polarizations: one antenna in vertical polarization and the other in horizontal polarization. The user will select the antenna in need. Omni antennas are not relevant for co-location. Only the selected antenna is operational. Configuration is done with the advanced window of the Unit Manager Tool (See paragraph 10.4.1). If the “External Antenna Select” check box is selected the detached antenna is selected, otherwise the integrated antenna is selected. Note: The FCC 15.203 requirement prohibits the connection of detached antennas with standard N-type connectors. In order to meet this requirement, the detached antenna connectors provided on GigAccess™ models (with no integral antenna) are non-standard, TNC connector. Only professional technician will perform the installation. 2.4.3.3. Guidelines for Selecting Outdoor Location Select the appropriate locations for the outdoor unit using the following guidelines: • The outdoor unit can be pole or wall mounted. Its location should allow easy access to the unit for installation and testing. • The AU should be installed where it provides coverage of all SUs in the area it is intended to serve. The higher the AU or its detached antenna, the better coverage it can provide. • When using a detached antenna, the AU should be installed as near as possible to its antenna. Note: The distance between any two antennas should be at least 50 cm. Warning! For a base station or any installation consisting of more than one outdoor unit (AU or SU) the safety distance for all persons should be at least 2 meters. Page 19 of 47 February 2003 Rev. A 2.4.3.4. SU Antenna Alignment Antenna alignment can be done with GigAccess™ Unit Manager software tool. The tool runs on PC with Windows operating system. In general, low gain antenna (such as omni antennas) do not required alignment due to their very wide radiation pattern. High gain antennas have a narrow beam width and therefore require alignment procedure in order to optimize the link. Instruction hereunder can be done after completion the connection of the AU and SU outdoor units to their indoor Outlet. Please perform the following steps in order to align the antenna: 1. Attach data cable from the PC to the SU Indoor Outlet data port. It is possible to attach special provided cable marked “data only” to a vacant Outdoor Unit port. WARNING! Do not attach standard CAT 5 cable from the Outdoor Unit directly to the PC. Connecting the PC directly to the Outdoor Unit may cause damaged to the Ethernet NIC in the PC. 2. Start “GigAccess Unit Manager” application. 3. Press on the “Start Session” button (“S” symbol) 4. Select the SU from the popup address window 5. Select “Installation” at the left menu tree 6. Rotate the antenna until you get maximum RSSI with minimal PER shown on the right bars see the installation window in the Unit Manager Tool (Figure 10-3). WARNING! Do not stand in front of transmitting antenna. Rotate the antenna from the rear side. 7. Secure the antenna by fastening the mounting screws. 2.4.3.5. Antenna Polarization The SU antenna polarization must be the same as in the AU antenna. In most applications, the preferred orientation is vertical polarization. Above ground propagation of the signal is better when it is polarized vertically. To verify antenna polarization, refer to the assembly instructions supplied with the antenna set. (The polarization of integrated antenna is marked on the backside). 2.4.4. Sealing The outdoor unit must be sealed against rain with the rubber grommets. Page 20 of 47 February 2003 Rev. A 2.5. Subscriber PC Setup • • In Case of specific IP setup - Configure the PC NIC to the same specific IP address as configured in the Base Controller. For this configuration follow the following steps: Press right click on the Network Neighborhood Icon. Select the Protocol reed and press properties. Choose the Specify an IP address and fill in the required specific IP address. In Case of DHCP setup - Configure the PC NIC obtain an IP address from DHCP server. For this configuration follow the following steps: Press right click on the Network Neighborhood Icon. Select the Protocol reed and press properties. Choose Obtain an IP address from DHCP server. Page 21 of 47 February 2003 Rev. A 2.6. Indoor Outlet Installation 2.6.1. Indoor Outlet Indoor Outlet is wall mounted. In case of multiple Indoor Units needed at the same location it is possible to attach the units to each other to form a stack unit. To Outdoor Unit (AU/SU) To Ethernet To Power Supply Figure 2-4: Indoor Outlet – Metal Model Figure 2-5: Power Supply for Indoor Outlet (This picture is for illustration only!) Page 22 of 47 February 2003 Rev. A 2.6.2. Cables Straight CAT5- Gauge 24-shielded outdoor rated cable, must be installed between Outdoor Unit and Indoor Outlet. It should be UV resistant and flame retardant. The cable should be UL listed and contain at least 4 twisted pairs. The outdoor cables scheme is given in Appendix F – Outdoor Cables Scheme. The Indoor Outlet side and Outdoor Unit side will crimped with RJ45 tool. CAT5 cable must not exceed 300 feet (91 meters). Use a suitable primary protector in accordance with article 800 in the NEC, if the exposed part of the CAT5 cable exceeds 140 feet (42 meters). Requirements of NEC articles 725 and 800 for the appropriate wiring methods during cable installation, shall be satisfied. The Outdoor Unit side will be assembled by the following list (See Figure 2-6): • Insert seal bracket (grommet clamping plate) on the cable. • Insert rubber seal (grommet) on the cable. • Crimp the RJ45 Plug. Figure 2-6: Cable preparation for Outdoor Unit • Insert the RJ45 to the Outdoor Unit. See Figure 2-7 and Figure 2-8. • Insert NC -6 screws with spring washer to the seal bracket. Page 23 of 47 February 2003 Rev. A Figure 2-7: Cable assembly to Outdoor Unit Figure 2-8: Cable insertion to Outdoor Unit. • Fasten the seal bracket. See Figure 2-9. • The unused port should be left sealed. Page 24 of 47 February 2003 Rev. A Figure 2-9: Cable connection to Outdoor Unit The Indoor Outlet side cables assembled as follows: 1. Crimp the RJ45 Plugs on cable ends to form the Outdoor Unit cable. 2. Plug the Outdoor Unit cable to the RJ45 Jack marked “AU/SU”. 3. Plug standard CAT5 cable from the PC to the RJ45 Jack marked “10/100 BT” 4. Plug the DC plug from the AC/DC power supply to the DC jack marked “48VDC” Warning: Do not attach standard CAT 5 cable from the PC to the Indoor Unit RJ45 jack marked “AU-SU”. Connecting the PC directly to the Outdoor Unit may cause damaged to the Ethernet NIC in the PC. Grounding Screw Power Supply Cable (in the back side) Ethernet (to PC) Cable to Outdoor Unit Figure 2-10: Cable connection to Indoor Outlet Page 25 of 47 February 2003 Rev. A 2.6.3. Grounding 2.6.3.1. Grounding the Outdoor Unit (AU /SU) The outdoor unit shall be connected to a protective earth with not less than 10 AWG conductors having green-yellow insulation. Figure 2-11 shows the grounding cable from outdoor unit external screw to adjacent grounding rod. The cable should be long enough to reach from the mounting pole to the grounding rod with 3 to 6 feet extra to allow for strain relief. Figure 2-11: Ground Connection to Outdoor Unit Protection from Lightning US National Electric Department of Energy Handbook 1996 specifies that radio and television lead-in cables must have adequate surge protection at or near the point of entry to the building. The code specifies that any shielded cable from a detached antenna must have the shield directly connected to a 10 AWG wire that connects to the building ground electrode. The ground wire shall be terminated with UL listed Lug with a diameter of 0.2 inch (5.2 mm). Page 26 of 47 February 2003 Rev. A 2.6.3.2. Grounding the Indoor Outlet (Metal Version Only!) The indoor Outlet shall be connected to a protective earth with 18 AWG conductors having greenyellow insulation. The grounding cable shall be connected to the indoor external screw locating at its backside. The cable should be long enough to reach from the mounting pole to the grounding rod with 3 to 6 feet extra to allow for strain relief NOTE! Only metal version of indoor Outlet should be grounded. There is no need to ground Plastic version of Indoor Outlet. FCC Notice, USA This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient the relocate-receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device must accept any interference received including interference that may cause undesired operation. Any unauthorized modification or changes to this device without the express approval of WaveIP may void the user’s authority to operate this device. Furthermore, this device intended to be used only when installed in accordance with the instructions outlined in this manual. Failure to comply with these instructions may also void the user’s authority to operate this device and/or the manufacturer’s warranty 2.6.4. Consecutive Connection The SU Indoor Outlet provides power and data connection to the SU Outdoor unit. The connection is done by plugging data crossover CAT5 cable between SU and consecutive AU. In this case the total length of all wires from Indoor Outlet to the far Outdoor Unit should not exceed 600 feet (182 meters). To achieve DC power redundancy an additional indoor Outlet + power supply can be connected to the AU second port. Page 27 of 47 February 2003 Rev. A 3. GigAccessTM 2.4 Technical Specifications 3.1. General Specification Access technology TDMA (Time division multiple access) Duplexing schemes TDD (Time division duplex) Wireless PHY Interface Proprietary based on IEEE 802.11b Wireless MAC Interface Proprietary based on IEEE 802.16 Forward Error Correction Dynamic convolution FEC Regulatory FCC Part 15, UL 1950 Applications Access, Campus, Consecutive 3.2. Base Station - Access Unit (outdoor) Sectors (degrees) Sectors from 200 to 3600 SUs per sector (AU) 64 Physical Interface 2 x 10/100 Base-T (ODU) Connector Type RJ-45 Protocol Supported IP, ICMP, ARP, TCP, UDP and HTTP Packet classification Wire-speed layer 3 Output Power (at antenna port) -6 dBm up to +18 dBm (1 dB step) Software Update Remote Download via TFTP Operating Temperature -20°C - +55°C Operating Humidity 5% - 95% non condensing (Rainproof) Power (via indoor Outlet) 48 VDC, <10 Watt Mechanical 7” x 7” x 2” (detached antenna) Indoor outlet: • Interface: to AU RJ-45 + Led indication • Interface to WAN RJ-45 • Mechanical 4” x 2” x 1” • AC Input Voltage 100 – 240 VAC, 47 – 63 Hz Outdoor to Indoor Outlet Page 28 of 47 CAT5 shielded cable (Up to 90 meters) February 2003 Rev. A 3.3. High performance Subscriber Unit (outdoor) Physical Interface 2 x 10/100 Base-T (ODU) Connector Type RJ-45 Protocol Supported IP, ICMP, ARP, TCP, UDP, DHCP, and HTTP Packet classification Wire-speed layer 3 Output Power: (at antenna port) -6 dBm up to +18 dBm (1 dB step) Antenna: • Integrated 13.5 dBi or 15.5 dBi • Detached See Table 4-2 Software Update Over the Air Download via TFTP Operating Temperature -20°C - +55°C Operating Humidity 5% - 95% non condensing (Rainproof) Power (via indoor Outlet) 48 VDC, <10 Watt Mechanical 7.5” x 7.5” x 2” (13.5 dBi antenna) 12” X 12” X 2” (15.5 dBi antenna) Indoor outlet: • Interface: to AU RJ-45 + Led indication • Interface to WAN RJ-45 • Mechanical 4” x 2” x 1” • AC Input Voltage 100 – 240 VAC, 47 – 63 Hz Outdoor to Indoor Outlet CAT5 shielded cable (Up to 90 meters). Page 29 of 47 February 2003 Rev. A 3.4. Radio Specifications Operating Frequency 2.400 – 2.483 GHz ISM band RF Waveform Direct Sequence Spread spectrum (DSSS) Modulation DQPSK, 16CCK1, 256 CCK Processing Gain 10.4 dB EIRP USA/FCC: +36 dBm (max) Europe/ETSI: +20 dBm (max) Antenna Polarization Vertical or Horizontal Number of Channels US: 13 Europe: 13 Data Rates 11 Mbps, 5.5 Mbps, 2 Mbps Radio Sensitivity @11 Mbps: -82 dBm, IE-2 PER2 @5.5 Mbps: -87 dBm, IE-2 PER @2 Mbps: -89 dBm, IE-2 PER 3.5. Management NMS Management Architecture - Distributed management located at multiple base controllers with automatic load balancing and fault tolerance. - Self Discovery - Alarms and status Indications - Remote SW downloads to outdoors units. Physical Interface 10/100 Base-T Connector Type RJ-45 Compliant with Ethernet/IEEE 802.3 Protocol Supported GigAccess™ Internal Protocol (GIP), SNMP QoS Services (SLAs) Constant Bit Rate (CBR), Best Effort (BE) QoS Support Criteria Bandwidth, Latency. CCK - Complementary Code Keying (See INTERSIL AN9850.2) PER - Packet Error Rate Page 30 of 47 February 2003 Rev. A 4. Appendix A – WaveIP Approved Antennas Antenna Type DirectionalFlat Panel Model Gain [dBi] MTI-1004/C/A MTI-30081/C/A MARS: MA-WA24-1X 13.5 15.5 15.5 Beam Width Dimension Ideal for: [mm] 33 190x190x30.5 Medium Range, Multipoint links. 20 305x305x25 Medium Range, Multipoint links. 20 305x305x30 Medium Range, Multipoint links. Table 4-1: Integrated Antennas for GigAccess™ Antenna Type DirectionalFlat Panel Omni Directional Model Gain [dBi] Beam Width MTI-345010/C/A 18 17 Hyperlink Tech-HG2409U 360 x15 Hyperlink Tech-HG2410U 10 360 x8 Hyperlink Tech-HG2412U 12 360 x8 NCG GP-24 12 360 x5 NCG GP-24-3 12 360 x5 13 90 – AZ Dimension 450x450x36 Long Range, Multipoint links. 50 cm Short Range, Multipoint links, 360 coverage (AU only) 100 cm Short Range, Multipoint links, 360 coverage (AU only) 120 cm Medium Range, Multipoint links, 360 coverage (AU only) 5 ft + 10 inch Medium Range, Multipoint links, 360 coverage (AU only) 5 ft + 10 inch Medium Range, Multipoint links, 360 coverage (AU only) (3 deg down-tilt) Base Station Antenna MT-363010/HN /NV Ideal for: 510x330x30 mm Multipoint link (AU only) 1000x330x30 mm Multipoint link (AU only) 600x140x30 mm Multipoint link (AU only) 1200x140x30 mm Multipoint link (AU only) 16 - EL MT-364028 /NV 17 90 – AZ 8 - EL MARS: MA-WC24-5X 14 60 – AZ 12 - EL MARS: MA-WC24-6X 17 60 – AZ 6.7 - EL Parabolic Dish Hyperlink Tech-HG2424G 24 Andrew-26T-2400-1 23 7.5 100.3x59.7cm Long Range Multipoint links and Point-to-point link 99.7x60x38cm Long Range Multipoint links and Point-to-point link Table 4-2: Detached Antennas for GigAccess™ Page 31 of 47 February 2003 Rev. A 5. Appendix B: Calculation RF Link Budget Proper RF link planning ensures that the AU/SU receives sufficient signal power to maintain the desired Bit Error Rate (BER). The following section gives a brief description of the basic RF terms and describes the calculation of the maximum safe distance versus the antenna gain. A typical radio system is given hereunder: Gr Gt Ct AU (Transmitter) Pt Cr Pr SU (Receiver) Figure 5-1: Radio Link – General description The following variables are used to calculate the link budget: Pt - Transmitted Power in dBm. Ct – Transmitter Cable Attenuation in dB. Gt - Transmitting antenna Gain in dBi. EIRP – Effective Isotropic Radiated Power in dBm. This is the power radiating from the antenna, taking into account the output power from the transmitter, connector losses, cable losses and antenna gain. PL - Path Loss in dB. This is the signal loss as it travels through the air. Gr - Receiving antenna Gain in dBi. Cr – Receiver Cable Attenuation in dB. Pr – Receiving Power Level at Receiver in dBm. Sr – Receiver Sensitivity in dBm (The minimum RF signal power level required at the input of the receiver for certain performance IE-5 BER) GM – Gain (Fade) Margin in dB. The fade margin is the amount by which the system gain plus total gain exceeds the path loss or in other words this is the number of dB that the received signal strength exceeds the minimum receiver sensitivity. Any wireless system requires some level of fade margin to compensate for RF path fading due to weather conditions or multipath interference. (The transmitted signal arrives at the receiver from different directions, with different path length, attenuation and delays. The summed signal at the receiver may result an attenuated signal). The GigAccess™ recommended fade margin at 2.4 GHz is 10 dB minimum. Page 32 of 47 February 2003 Rev. A Example of Link Parameters: Pt = 18 dBm Ct = Cr = 0 dB Gt = Gr = 13.5 / 15.5 dBm Sr (11 Mbps) = 85 dBm, Sr (5.5 Mbps) = 87 dBm, Sr (2 Mbps) = 88 dBm GM = 10 dB (1) EIRP = Pt − C t + G t (2) Pr = S r = EIRP − PL − GM + Gr − Cr (3) PL = EIRP + G r − C r − S r − GM (4) PL = 32.4 + 20 × log(FMHz ) + 20 × log(RKm ) (5) PL 2 . 4 GHz = 100 + 20 × log( R Km ) (6) R Km = 10 PL −100 20 13.5 dBi Antenna 15.5 dBi Antenna Rate=11 Mbps Rate=11 Mbps Pt 18 18 Ct Gt 13.5 15.5 EIRP 31.5 33.5 Gr 13.5 15.5 Cr Sr -82 -82 Pl 117 121 RKm 11 Detailed results for RF calculation is given in Appendix C – Max RF Power and Distance versus Antenna Gain Page 33 of 47 February 2003 Rev. A 6. Appendix C – Max RF Power and Distance versus Antenna Gain FCC (point-to-multi-point operation) Antenna Antenna Gain Max RF Power [dBi] [dBm] Detached 18.5 26.5 p2mp Sector Detached 10 18.5 28.5 p2mp Sector Detached 12 18.5 30.5 p2mp Sector Detached 13 18.5 31.5 p2mp Sector Integrated 13.5 18.5 32 p2mp Sector Detached 14 18.5 32.5 p2mp Sector Integrated 15.5 18.5 34 11 p2mp Sector Detached 17 18.5 35.5 16 p2mp Sector Detached 18 18 36 20 p2mp Sector Detached 23 11 36 25 p2mp Sector Detached 24 12 36 30 p2mp Sector Type EIRP Distance [dBm] at Highest Rate Sector Type [Km] Table 6-1: Max RF Power and Distance for FCC in point-to-multi-point Note! For point-to-multi-point the output EIRP should never exceed +36dBm for any antenna combination used. p2mp = Point To Multi Point Page 34 of 47 February 2003 Rev. A FCC – (point-to-point operation) Antenna Type Detached Antenna Gain Max RF Power [dBi] [dBm] 24 18.5 EIRP Distance [dBm] at Highest Rate Sector Type [Km] 42.5 p2p 50 Table 6-2: Max RF Power and Distance for FCC in point-to-point Note! When the system is used exclusively for fixed point-to-point operation, the output EIRP can exceed +36dBm for the 24 dBi antenna according to FCC 15.247(b)(4)(i). Therefore this option is only allowed by password of administrator privilege and should be done by a professional installer only! ETSI Antenna Antenna Gain Max RF Power [dBi] [dBm] Detached 12 20 p2mp Sector Detached 10 10 20 1.3 p2mp Sector Detached 12 20 1.6 p2mp Sector Detached 13 20 1.8 p2mp Sector Integrated 13.5 6.5 20 1.9 p2mp Sector Detached 14 20 p2mp Sector Integrated 15.5 4.5 20 p2mp Sector Detached 17 20 3.5 p2mp Sector Detached 18 20 p2mp Sector Detached 23 -4 20 5.6 p2mp, p2mp Detached 24 -4 20 p2mp, p2mp Type EIRP Distance [dBm] at Highest Rate Sector Type [Km] Table 6-3: Max RF Power and Distance for ETSI p2p = Point To Point Page 35 of 47 February 2003 Rev. A 7. Appendix D: RF Hazard Distance Calculation The Power density is given by: (1) S= P×G 4 × π × R2 Therefore: (2) R= P×G 4 ×π × S where: S = Power Density = 1 [mW/cm2] P = Power input to the antenna. [mW] G = Antenna Gain in the direction of interest. [In numeric format] R = Distance to the center of radiation antenna [cm] (3) PdBm = 10 × log PmW Therefore: (4) PmW = 10 PdBm 10 The hazard distances versus antenna gain are listed in Table 7-1. Note! GigAccess™ was designed for fixed and mobile applications. Page 36 of 47 February 2003 Rev. A point-to-multi-point operation Antenna Gain Tx Power Safe Distance Sector Type [dBi] [Numeric] [dBm] [mW] [cm] 6.3 18.5 70.8 5.96 p2mp 10 10.0 18.5 70.8 7.51 p2mp 12 15.8 18.5 70.8 9.45 p2mp 13 20 18.5 70.8 10.6 p2mp 13.5 22.4 18.5 70.8 11.23 p2mp 14 25.1 18.5 70.8 11.9 p2mp 15.5 35.5 18.5 70.8 14.14 p2mp 17 50.1 18.5 70.8 16.81 p2mp 18 63.1 18 63.1 17.8 p2mp 23 199.5 13 20 17.8 p2mp 24 251 12 15.8 17.8 p2mp Table 7-1: Hazard Distance versus Antenna Gain for Point to Multi Point When using the system for point to multi point (p2mp) applications all outdoor units must be installed with a separation distance of at least 20 cm from all persons during normal operation. For a base station or any installation consisting of more than one outdoor unit (AU or SU) the safety distance for all persons should be at least 2 meters. point-to-point operation Antenna Gain Tx Power Safe Distance [dBi] [Numeric] [dBm] [mW] [cm] 24 251 18.5 70.8 37.63 Sector Type p2p Table 7-2: Hazard Distance versus Antenna Gain for Point to Point When using the system for point to point (p2p) applications all outdoor units must be installed with a separation distance of at least 2 meters from all persons during normal operation Page 37 of 47 February 2003 Rev. A 8. Appendix E – RF Channel List Operating Band: 2400 MHz - 2483.5 MHz Channel No Frequency 2412 MHz 2417 MHz 2422 MHz 2427 MHz 2432 MHz 2437 MHz 2442 MHz 2447 MHz 2452 MHz 2457 MHz 10 2462 MHz 11 2467 MHz 12 2472 MHz Table 8-1: RF channel List Page 38 of 47 February 2003 Rev. A 9. Appendix F – Outdoor Cables Scheme INDOOR TO OUTDOOR RJ-RJ-DATA+POWER+LEDS-STRAIGHT OR/W OR OR/W OR GR/W BL GR/W BL BL/W GR BL/W GR BR/W BR BR/W BR SU TO CONSECUTIVE AU RJ-RJ-DATA+POWER+LEDS-CROSS GR/W GR OR/W OR OR/W BL GR/W BL BL/W BL/W GR BR OR BR/W BR/W BR Figure 9-1: Outdoor Cables Scheme Page 39 of 47 February 2003 Rev. A 10. Appendix G - Using the Unit Manager Tool 10.1. General The Unit Manager Tool is used for installation and configuring the Unit (AU or SU). A technician that installs and maintain an AU or an SU should use this tool. The tool is divided logically into two levels, standard and advanced. At startup the tool automatically direct the technician into a simple installation page that includes all the information needed to install the unit. When the need arises the technician can select another pages and operations in order to perform more complex infrequent operations (like burning a new firmware etc.). The tool has the ability to discover GigAccess™ Units connected to the network and allows configuration of one unit at a time. This manual gives a short description of the features available and is using terms from the GigAccess™ system. A more complete and detailed manual will be available shortly. 10.2. Menu Commands 10.2.1. Selecting adapter The adapter used by the GigAccess™ Unit Manager can be selected in the MenuàToolsàSelect Adapter. A list of the adapter list installed in the computer is shown. Select the appropriate adapter and press ok. The adapter selected is saved in the application configuration file. Figure 10-1: Adapter Selection Window in Unit Manager Tool Page 40 of 47 February 2003 Rev. A 10.3. Toolbar Commands 10.3.1. Start Session This command discovers (broadcast) the units on the network. The application waits (discover time) for replies from the units (AUs and SUs) and display a list of the units replied. The discover time interval can be configured in the application configuration file. Figure 10-2: Discover Window in Unit Manager Tool Select one the units from the list, select a Login User and type the password. Finally press the Login Button. The application starts a session with the selected unit and the unit configuration is retrieved and displayed. As long as the session is active, the unit type, MAC address and IP address are displayed on the title of the application window. The Login settings can be saved in the application configuration file by checking the Remember Setting Checkbox. 10.3.2. End Session This command ends the session with the unit and the title of the application window is changed. 10.3.3. Refresh Unit Parameters This command refreshes the displayed unit configuration by getting it again from the unit. 10.3.4. Auto Reconnect When the Auto-Reconnect button is pressed and a session with a unit ends the application tries to reconnect to the unit until a session is started. If the Logger was active before the session ended, the Logger is started again. 10.3.5. Start Logger Enables the output of log messages from the unit and printing to the log window and log file (Admin user only). Page 41 of 47 February 2003 Rev. A 10.3.6. Stop Logger Disables the output of log messages (Admin user only). 10.3.7. Clear Log Clears the log window. 10.3.8. Log to File When pressing the Log to File button, the “GigAccessUnitManager.log“ is cleared and all log printed to the log window are also printed to the log file. The log file is placed in the application directory and can be opened only when the Log to File button is released. 10.3.9. View Log Opens the “GigAccessUnitManager.log“ in Notepad. Can be done only if the Log to File button is released. 10.3.10. Reset Text Gets the Last reset reason and prints to the log window and log file. 10.4. Installation Window The Installation Window provides a simple to use installation and configuration of the general parameters of the unit. The window contains both AU and SU fields. The appropriate fields are disabled when connecting to an AU or SU unit. Figure 10-3: Installation Window in Unit Manager Tool The Installation window contains the following fields: Ø MAC Address – the Unit unique MAC Address. Ø IP Address – the Agent IP Address. This field can be configured. Ø Subnet Mask – the Agent Subnet Mask. This field can be configured. Ø Default Gateway – the default gateway the Agent needs to use for transfer packets out of its subnet. This field can be configured. Page 42 of 47 February 2003 Rev. A Ø Primary AUID – the Primary AU MAC Address the SU needs to connect to. This field can be configured for SU only. Ø Secondary AUID – the Secondary AU MAC Address the SU needs to connect to. This field can be configured for SU only. Ø Estimated Range – the estimated range in meters between the AU and the SU. This field is updated when the SU is online (Operation Mode) and relevant for SU only. Ø Operation Mode – this field shows the status of the Unit. The status is different between AU and SU: AU Operation Modes: § BC Negotiation – the AU tries to negotiate with the Base Controller in order to get configuration file. § Online – the AU has the configuration file (Local Configuration File or the one it received from the Base controller) and RF channel is online. SU Operation Modes: § Scanning – the SU scans the RF channels marked in the RF channel list and search for the Primary/Secondary AUID. § Online – the SU is connected to the AU if the SU exists in the AU configuration file. Ø RF Channel – the RF Channels the SU should scan. There should be at least to channels between two successive channels that the SU should scan (RF channel band). This field can be configured for SU only. Ø RSSI – this field is used to adjust the position of the SU during installation. The SU should be position in the direction where the RSSI value is the highest. A RSSI value must be greater the “0x40”. This field is relevant for SU only. Ø PER – Packet Error Rate, this field shows the quality of the RF channel for periodic interference. This field is relevant for SU only. When the configuration is updated it can be burned to the unit by pressing Submit. The Unit performs reset and reconnect to it should be done in order to verify the changes. Page 43 of 47 February 2003 Rev. A 10.4.1. Advanced Window The Advanced Window provides the ability to change more detailed parameters of the unit. Figure 10-4: Advanced Window in Unit Manager Tool The Advanced window contains the following fields: Ø Admin Login Password – the Administrator password that should be entered when trying to login as an Admin user (Admin user only). Ø User Login Password – the User password that should be entered when trying to login as a User user. Ø Antenna Gain – select the antenna used (Admin user only). Ø TX Power – Select the output power at the antenna connector (Admin user only). Changes of the TX Power must be done by an Expert Technician only. This TX Power value must be set according to the type of the antenna used in order to insure that the power at the output of the antenna stands in the selected regulation restrictions. Ø Detached Antenna Select – this field is used to select Internal or Detached antenna (Admin user only). For now, when the flag is set so the Internal antenna is selected. The default for this flag is to use internal antenna. Detached antenna should be selected only when the unit has and detached antenna connector. Ø Ethernet Switch Port 1 Configuration – set the speed and duplex of port 1. Available values are: 10M Full Duplex, 100M Full Duplex and Auto-Negotiation. Ø Ethernet Switch Port 2 Configuration – set the speed and duplex of port 2. Available values are: 10M Full Duplex, 100M Full Duplex and Auto-Negotiation. Ø Ethernet Switch Priority – set the priority between the two Ethernet ports. Available values are: Disabled, Port 1 High Priority and Port 2 High Priority. Ø Enable Ethernet Switch Security – when this flag is set, traffic between Port 1 to Port 2 is blocked (VLAN). Ø Regulation – select the appropriate regulation: FCC or ETSI. (Admin user only). Page 44 of 47 February 2003 Rev. A Ø Link Type – select the appropriate link type: point-to-multi-point or point-to-point. (Admin user only). In point-to-multi-point the output power (EIRP) will never exceeds +36dBm for any antenna combination. In point-to-point only EIRP can exceed +36dBm according to FCC 15.247(b)(4)(i). For the 24dBi antenna gain there is no limit of the output power and it can reach the max of +18.5dBm. This option is only allowed by password of administrator privilege and should be done by a professional installer only! When the configuration is updated it can be burned to the unit by pressing Submit. The Unit performs reset and reconnect to it should be done in order to verify the changes. 10.5. Boot Window The Boot Window displays the Boot Banks and the Active Boot Banks. Changes to the boot banks can be done only by an Admin user. The Boot Banks are used by the Boot Loader to decide which Firmware/PLD/PHY software should be loaded. The Actual Boot Banks that show which Firmware/PLD/PHY software the Boot Loader actually loaded. After the software was burned and verified (Software Window), the boot bank should be changed and burned by pressing Submit. It is necessary to reconnect to the unit and verify that the burned software was loaded - the Actual Boot Bank matches the Boot Bank. If the Boot Bank and the Actual Boot Bank does not match, the image burned is corrupted and should be burned again. Figure 10-5: Boot Window in Unit Manager Tool Page 45 of 47 February 2003 Rev. A 10.6. Software window 10.6.1. General The Software Window provides information of the burned Firmware, PLD and PHY SW in the unit. Figure 10-6: Software Window in Unit Manager Tool The information contains the following fields: Ø Bank Type – the bank type. Ø Size – the size of the image burned in the bank. Ø Version – the image version. Ø Date – the image date. Ø Time – the image time Ø Checksum – the image checksum. Note: value of “FF” in the bank field’s means there is no software is burned in this bank. 10.6.2. Firmware Window The Firmware Window provides the ability to burn a new firmware to one of the banks (Admin user only). The new software should not be burned to the actual boot Bank. The actual boot bank is displayed in the Boot Window. An alert message box is displayed if trying to burn the new software to the actual boot bank. When submitting the burn operation, log prints are printed to the log window and log file. When the burn is done the units resets and it is required to reconnect to it and check that the software was burned (View the Software Window). Finally the boot bank should be changed in the Boot Window. Figure 10-7: Firmware Window in Unit Manager Tool Page 46 of 47 February 2003 Rev. A 10.6.3. PLD Window The PLD Window provides the ability to burn a new firmware to one of the banks (Admin user only). The new software should not be burned to the actual boot Bank. The actual boot bank is displayed in the Boot Window. An alert message box is displayed if trying to burn the new software to the actual boot bank. When submitting the burn operation, log prints are printed to the log window and log file. When the burn is done the units resets and it is required to reconnect to it and check that the software was burned (View the Software Window). Finally the boot bank should be changed in the Boot Window. Figure 10-8: PLD Window in Unit Manager Tool 10.6.4. PHY Window The PHY Window provides the ability to burn a new firmware to one of the banks (Admin user only). The new software should not be burned to the actual boot Bank. The actual boot bank is displayed in the Boot Window. An alert message box is displayed if trying to burn the new software to the actual boot bank. When submitting the burn operation, log prints are printed to the log window and log file. When the burn is done the units resets and it is required to reconnect to it and check that the software was burned (View the Software Window). Finally the boot bank should be changed in the Boot Window. Figure 10-9: PHY Window in Unit Manager Tool Page 47 of 47
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Create Date : 2003:03:19 12:43:05Z Modify Date : 2003:03:21 20:24:41-05:00 Page Count : 47 Creation Date : 2003:03:19 12:43:05Z Author : AmitA Producer : Acrobat PDFWriter 4.05 for Windows NT Mod Date : 2003:03:21 20:24:41-05:00 Metadata Date : 2003:03:21 20:24:41-05:00 Title : User Guide.PDF Creator : AmitAEXIF Metadata provided by EXIF.tools