WaveLynx Technologies WLTC-DHMM-1K37 125 kHz and 13.56 MHz single gang RF reader with a keypad, 125 kHz and 13.56 MHz single gang RF reader with a keypad and Bluetooth communication capability. User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3088925
Application ID	xrqLRBbqI3AWlMA5K8r9eQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	28.41kB (355104 bits)
Date Submitted	2016-08-05 00:00:00
Date Available	2016-08-11 00:00:00
Creation Date	2016-08-04 09:48:22
Producing Software	Microsoft® Word 2013
Document Lastmod	2016-08-04 09:48:22
Document Title	Users Manual
Document Creator	Microsoft® Word 2013
Document Author:	Catherine Carducci

Wall Mounted Reader Installation
This installation guide applies to the following types of readers:
 ET20 – Single Gang Reader
 ET25 – Single Gang Reader with Keypad
Included:



(2) #6 Screws
Reader, Backplate, and Wall Plate 
(1) #4-40, (1) pin-in-torx
(4) #4 Screws
The Following tools will needed to install
a wall mount reader:
 Phillips Screwdriver
 1” (25mm), 1/8” drill bits
 T8 Security Torx Bit (optional for increased tamper detection)
Install Metal Wall Plate to Single Gang Box
Connect the wall plate to the single gang box using the provided #6 screws. Alternatively you can use the provided #4 screws in
the four outer holes for other installation requirements. Drywall installations will require molly bolts.
Alternative for
situations
outside of a
single gang box
installation.
Standard Single
––
Gang Box
Installation
Wire the Cable to the Control Panel
Max Length to Panel
Length
AWG
200’ (60 m)
22
300’
20
500’
18
Current @ 12 V and 25 C
Avg. mA
Max. mA
110
160
Current for ET25 @ 12 V and 25 C
Avg. mA
Max. mA
140
190
Common Cable Connections
Red
Power In
Black
Ground
Shield
Shield Ground
Brown*
Tamper Out
Green
Wiegand Data 0 / RS 485A
White
Wiegand Data 1 / RS 485B
Yellow*
Beeper Control
Blue*
Green LED Control
Orange*
Red LED Control
Attach the Reader to the Wall plate
Align the reader so that the tabs of the base plate slide into
the slots on the wall plate and slide the reader into position.
*these wires are only used in
Wiegand readers.
Install the Reader Screw
Install the #4-40 screw or pin-in-torx at the bottom of the
reader.
Screw or
pin-intorx
Test the Reader
Power the reader, the red light-bar will light, followed by a
beep. Present a valid credential to the reader and the
light-bar will turn green.
Contact Us
WaveLynx Technologies
(303) 327-1477
www.wavelynxtech.com
*Patent Pending
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by
WaveLynx could void the user's authority to operate the equipment.
”This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux
CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
Language                        : en-US
Tagged PDF                      : Yes
Author                          : Catherine Carducci
Creator                         : Microsoft® Word 2013
Create Date                     : 2016:08:04 09:48:22-06:00
Modify Date                     : 2016:08:04 09:48:22-06:00
Producer                        : Microsoft® Word 2013

EXIF Metadata provided by EXIF.tools