WaveLynx Technologies WLTC-DHMM-1M37 125 kHz and 13.56 MHz RF reader, 125 kHz and 13.56 MHz RF reader with Bluetooth communication capability User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3088741
Application ID	9AukTYOfflUR/uQenP9+Gg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	15.37kB (192162 bits)
Date Submitted	2016-08-04 00:00:00
Date Available	2016-08-11 00:00:00
Creation Date	2016-07-19 09:02:01
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2016-07-19 09:02:01
Document Title	Microsoft Word - Mullion Install Guide 7-19-16A.docx
Document Creator	PScript5.dll Version 5.2.2
Document Author:	ewong

Wall Mounted Reader Installation
This installation guide applies to the ET10 Mullion Reader.
Included:
•
•
•
(2) #6 Screws
Reader, Backplate, and Wall Plate
(1) #4-40, (1) pin-in-torx
Mounting Holes for Wall Plate
Drill two mounting holes at a minimum of 1.7” apart. Drill a
½” hole in the center for the pigtail wire to pass through.
Use the wall
–– plate as a guide for drilling.
Mounting hole
distance is
adjustable, use
the provided
#6 screws
The Following tools are needed to install a mullion reader:
• Phillips Screwdriver
• 6-32 Tap (if installing on metal)
• 1/2” drill bit
• T8 Security Torx Bit (optional for increased tamper detection)
Install Metal Wall Plate
Once the holes are prepared, screw the wall plate in using
the provided #6 screws.
½” Hole for
Pigtail
Wire the Cable to the Control Panel
Max Length to Panel
Length
AWG
200’ (60 m)
22
300’
20
500’
18
Current @ 12 V
Avg. mA
Max. mA
100
160
Common Cable Connections
Red
Power In
Black
Ground
Shield
Attach the Reader to the Wall Plate
Align the reader so that the tabs of the base plate slide into
the slots on the wall plate and slide the reader into position.
Shield Ground
Brown*
Tamper Out
Green
Wiegand Data 0 / RS-485A
White
Wiegand Data 1 / RS-485B
Yellow*
Blue*
Orange*
Beeper Control
Green LED Control
Red LED Control
*these wires are only used in
Wiegand readers.
Install the Reader Screw
Install the #4-40 screw or pin-in-torx at the bottom of the
reader.
Screw or
pin-intorx
Test the Reader
Power the reader, the red light-bar will light, followed by a
beep. Present a valid credential to the reader and the
light-bar will turn green.
Contact Us
WaveLynx Technologies
(303) 327-1477
www.wavelynxtech.com
*Patent Pending
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by Wavelynx could void the user's authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre
le fonctionnement.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 1
Producer                        : GPL Ghostscript 8.15
Create Date                     : 2016:07:19 09:02:01
Modify Date                     : 2016:07:19 09:02:01
Title                           : Microsoft Word - Mullion Install Guide 7-19-16A.docx
Creator                         : PScript5.dll Version 5.2.2
Author                          : ewong

EXIF Metadata provided by EXIF.tools