Wavion WBS2400-2S WBS-2400 Outdoor Wi-Fi Base Station User Manual WBS2400 5800 IG Sector AF Rev 3

Wavion Ltd. WBS-2400 Outdoor Wi-Fi Base Station WBS2400 5800 IG Sector AF Rev 3

Contents

Users Manual II

WBS-2400 & WBS-5800 Outdoor Wi-Fi Sector Base Station Installation Guide Rev. 3 February 2009
Note: To better reflect the value of Wavion products we are changing the name of our product family from Access Points (AP) to Wireless Base Stations (WBS), consequently the existing WS-410 product name will be changed to Wavion WBS-2400. The new product name emphasizes the difference in architecture (Multiple Radio system) and the value to customer, superiority in performance (coverage, capacity, indoor penetration and immunity to interference) of Wavion WiFi base station over any other standard outdoor WiFi access point products available in the market. All references in Wavion's documentation to WS-410 refer also to the WBS-2400, and vice versa. Both products are exactly the same except for the name change. Copyright Notice ©2006, 2007, 2008 Wavion, Inc. All rights reserved. Wavion is a registered trademark of Wavion in the United States and certain other jurisdictions. Specifications are subject to change without notice. FCC Notice to Users and Operators This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. If this equipment does cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by using one of the following measures: • Reorient or relocate the receiving antenna. • Increase separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician.
Installation Guide 3 Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: According to the FCC rules the WBS-5800 unit must only be used for fixed point to point applications with fixed clients. R&TTE Compliance Statement This equipment (ETSI-models only) complies with all the requirements of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE)
4 Wavion Networks Contents Chapte r 1 About This Guide ........................................................................ 5 Preface .................................................................................................... 5 Conventions ............................................................................................. 5 Contacting Technical Support .................................................................... 6 Chapte r 2 Introduction ............................................................................... 7 Chapte r 3 Package Content ........................................................................ 8 Chapte r 4 Installing the Wavion WBS-2400/5800 Sector Base Station .. 10 Important Safety Instructions.................................................................. 11 Preparing for Installation......................................................................... 12 Choosing a Location................................................................................ 13 Preparing the Site ................................................................................... 13 Mounting Strategies................................................................................ 14 Using Hose Clamps ................................................................................. 14 Mounting on a Pole/Streetlight ................................................................ 15 Grounding the Data Protection Device...................................................... 18 Connecting Power and DATA................................................................... 20 Safety Information for the Wavion WBS-2400/5800.................................. 24 Service Instructions ................................................................................ 25 Chapte r 5 Product Specification WBS-2400 Sector.................................. 26 Chapte r 6 Antenna 2.4GHz Specifications and Patterns .......................... 30 SF-245W 2.4GHz Sector Antenna ............................................................. 30 Chapte r 7 Product Specification WBS-5800 ............................................. 33 Chapte r 8 Antenna 5.8GHz Specifications and Patterns .......................... 39 MT-463009CV 5.8GHz Antenna Azimuth Patterns directional Antenna ........ 39 Chapte r 9 Installation Accessories ........................................................... 41 Ethernet Cables ...................................................................................... 42 Sun Protection ........................................................................................ 42 Lightning Protection ................................................................................ 42 Power Over Ethernet............................................................................... 42 Chapte r 10 Wind Loading Considerations .................................................. 43 Chapte r 11 Acronyms.................................................................................. 44 Chapte r 12 Appendix A: WBS-2400/5800 Product list............................... 46
5 Wavion Networks Chapter 1 About This Guide Preface This guide details the Wavion WBS-2400/5800 Sector installation procedures. The intended audience of this document is trained technical professionals. Conventions The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. The lightning flash with an arrowhead symbol within a triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The notebook is intended to alert the user of a note containing further information.
About This Guide 6 Wavion Networks Contacting Technical Support For technical support, contact Wavion using these methods: Address: Wavion Technical Support Wavion 6 Hayetzira Street, PO BOX 580 Yoqneam Illit, 20692 Israel Telephone: +972-4-9097300 Fax: +972-4-9097322 Email: support@wavionnetworks.com Web: www.wavionnetworks.com
Introduction Installation Guide 7 Chapter 2 Introduction WBS-2400/5800 Sector a high capacity, IP services oriented Broadband Wireless access system. WBS-2400/5800 Sector is a new category of Broadband Wireless Base Station designed from the ground up for metro-Wi-Fi deployments. The system employs wireless packet switched data technology to support high-speed IP services including fast Internet and Virtual Private Networks. WBS-2400/5800 Sector users are provided with a network connection that is always on, supporting immediate access to the Internet and other IP services at high data rates. The system is designed for cellular-like deployment, enabling the system architecture to vary in size and structure. A system can include any number of cells, each containing several base station access units for better coverage of densely populated areas. It is based on three antennas and radios and custom-built ASICs, utilizes Wavion's powerful multi-antenna signal processing technologies, and provides significant performance gains to off-the-shelf 802.11 standards-based The WBS-2400/5800 Sector may be mounted on streetlights or rooftops and may be easily interfaced with wired internet connections, wireless mesh or backhaul equipment. Complete management of the WBS-2400/5800 Sector is provided through SNMP, a graphical user interface, and SYSLOG services.
8 Wavion Networks Chapter 3 Package Content Check that the package contains: • POE injector unit with wall mounting kit • Outdoor Unit • Pole mounting bracket for the outdoor unit • Allen head wrench with 4 screws • Waterproof sealing tape for IP67 (band to sealing rubber) Additional Equipment and Tools required for Installation • Ethernet cable (straight for connecting to a hub/switch) • Crimping tool for RJ-45 connectors. • Ground cable with an appropriate termination. • Mains plug adapter or termination plug (if the power plug on the supplied AC power cord does not fit local power outlets). • Portable PC with Ethernet card and Telnet software and a straight Ethernet cable. WARNING: Use straight Ethernet (POE) cable connecting the injector to AF unit in order to have all the features work properly (reset button and Link LED). Using cross cable might cause turn Link led to “ON” permanently and also may be the cause software reset. DATA cable connecting the injector to the network can be cross cable as well.
Package Content Installation Guide 9 • Addition tools and materials, including appropriate means (e.g. a pole) for installing the outdoor equipment. • 1/4-inch flat blade screwdriver WARNING: ONLY experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities should install outdoor units and antennas. Failure to do so may void the WBS-2400/5800 product warranty and may expose the end user or Service Provider to legal and financial liabilities. Wavion and its resellers or distributors are not liable for injury, damage or regulation violations associated with the installation of Outdoor Units or antennas
10 Wavion Networks Chapter 4 Installing the Wavion WBS-2400/5800 Sector Base Station This guide explains how to safely install the Wavion WBS-2400/5800 Sector Base Station. The following topics are covered in this chapter: • Important Safety Instructions • Preparing for Installation • Mounting Strategies • Using Hose Clamps • Mounting on a Pole, or Streetlight • Grounding the Wavion WBS-2400/5800 • Connecting Power and Data • Safety Information for the Wavion WBS-2400/5800 • Service Instructions
Installation Guide 11 Important Safety Instructions WARNING: It is illegal to modify the construction of this product. Modifying the operating frequency or enhancing the transmit output power through the use of external amplifiers or other equipment is specifically disallowed by the "Telecommunications Act." WARNING: This device is for outdoor or indoor use with conditions that no harmful interference to authorized radio stations results from the operation of this device. This device shall not influence aircraft security and/or interfere with legal communications as defined in the "Telecommunications Act." If this device is found to cause interference, the operator of this equipment shall cease operating this device immediately until no interference is achieved. Note: This device must be installed by a trained professional, value added reseller or systems integrator who is familiar with RF planning issues and the regulatory limits in the United States of America. Caution: Read and save these instructions. Heed all warnings. Follow all instructions. Do not defeat the safety purpose of the grounding. Caution: Only use attachments/accessories specified by the manufacturer. Caution: Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way. For example, if the power-supply cord or plug is damaged, liquid has been spilled on the apparatus, objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, it does not operate normally, or has been dropped. Warning: Risk of personal injury or death when installing this device! There is a risk of personal injury or death if the WBS-2400/5800 antennas come near electric power lines. Carefully read and follow all instructions in this manual. By nature of the installation, you may be exposed to hazardous environments and high voltage. Use caution when installing the outdoor system. Warning: This apparatus must be connected to earth ground Warning: Do not open the unit. There is a risk of electric shock inside. Caution: You are cautioned that any change or modification not expressly approved in this manual could void your authority to operate this equipment.
12 Wavion Networks Caution: There are no user-serviceable parts inside. All service must be performed by qualified personnel. Caution Only UL listed parts and components will be used for installation. Use UL listed devices having an environmental rating equal to or better than the enclosure rating to close all unfilled openings. Caution To maintain Overvoltage (Installation) Category II, install a suitable surge suppressor device in the branch circuit to limit expected transients to Overvoltage Category II values. The limits are based on IEC60664 and are also located in Table 2H of UL60950 (for mains 110V, the transient rating is 1500V). Caution The WBS-2400/5800must be installed only with the equipped antennas. Caution A minimum distance of 40cm from the WBS-2400/5800X's antenna should be kept when the system is operated. Caution Read and save these instructions. Heed all warnings. Follow all instructions Preparing for Installation ONLY experienced installation professionals who are familiar with local building and safety codes and, wherever applicable, are licensed by the appropriate government regulatory authorities should install outdoor units and antennas. The following lists the equipment required for installation and explains how to prepare the installation site. WARNING: Do not modify the construction of this product. Modifying the operating frequency or enhancing the transmit output power through the use of external amplifiers or other equipment is illegal. WARNING This device is for use outdoors or indoors on the condition that operation of this device causes no harmful interference to authorized radio stations. This device shall not influence aircraft security and/or interfere with legal communications. If this device is found to cause interference, the operator of this equipment shall cease operating this device immediately.
Installation Guide 13 Choosing a Location To ensure the optimal performance select the locations for the equipment using the following guidelines:  The antenna (integrated on the front panel of the outdoor unit) should provide a direct, or near line of sight, with the sector location that need to be covered.  The antenna should be aligned to face the CPEs that aim to be in service, higher the placement of the antenna, the better the achievable link quality (but not in all cases).  Average rooftop (depend on the topology of the location) should be  The location of the outdoor unit should enable easy access to the unit for installation and testing  Avoid installations in locations that devices operating in the same frequency range.  The outdoor unit should be installed at the highest point of a metal pole that there will be no interference caused by RF reflections. If this is not possible, it should be installed at least 3 meters from the metal pole.  It is recommended to use maximum distance possible from an RF radiating source. Preparing the Site 1. Follow the appropriate electrical and building codes to ensure safe and durable wiring. 2. Follow the National Electrical Code (NEC) requirements, unless local codes in your area take precedence over the NEC code 3. The length of the indoor-to-outdoor Ethernet cable should not exceed 90 meters. The length of the Ethernet cable connecting the indoor unit to the user's equipment, together with the length of the Indoor-to-Outdoor cable, should not exceed 100 meters. 4. An appropriate ground cable should be available. Connect a grounding cable between the Ground terminal of the outdoor unit and a good ground connection. Please refer to standards for building entrance protection.
14 Wavion Networks Mounting Strategies Consider the available mounting structures and antenna clearance when choosing a mounting location. Wavion outdoor unit WBS-2400/5800 Sector should be mounted on horizontal pole only the antennas pointing vertically and clear of obstruction. It is recommended to attach ground and data cables to the WBS-2400/5800 Sector prior to mounting. Before mounting the WBS-2400/5800 Sector, read the wiring instructions in Grounding the Wavion WBS-2400/5800 and Connecting Power and Data. Note: The WBS-2400/5800 should be mounted with at least 4 ft/3 Meter of clearance around the antennas to eliminate potential interference from the mounting structure. Figure 4.1 Pole mounting kit for the Outdoor Unit & Sealing kit Using Hose Clamps Special hose clamps that include threaded holes are used by the mounting assembly to secure the WBS-2400/5800 Sector to the mounting structure. Figure 4.2 demonstrate how to correctly use the hose clamps. The bands must be threaded through holes in the pole bracket, and then attached horizontal pole and tightened. There are two pairs of threaded holes on the back of the unit, enabling to use the special clamps for mounting the unit on diverse pole diameters.
Installation Guide 15 Figure 4.2 Using Special Hose Clamps & Screwing the Clamps Mounting on a Pole/Streetlight WBS-2400/5800 Sector can be mounted on a pole, tower, or streetlight. It is recommended to mount the WBS-2400/5800 Sector on aluminum or galvanized steel structures. Note Before mounting the WBS-2400/5800, read the wiring instructions in Grounding the Wavion WBS-2400/5800 and Connecting a Data Port chapter.
16 Wavion Networks To mount the Wavion WBS-2400/5800 on a metal/wood/streetlight pole: 1. Choose a mounting location. You can attach the WBS-2400/5800 Sector outdoor unit to any pole or pipe with diameter of 3-10 inches. Wooden poles of larger diameter require different types of clamps (any streetlight arm with diameter of 3 to 10 inches will fit for this installation). 2. Slip the bands of the hose clamps through the slots of the pole bracket 3. Use the hose clamps to fasten the pole bracket to the pole. 4. Insert the WBS-2400/5800 Sector onto the pole bracket, obtain the correct position and tighten 4 bolts using 4mm Allen wrench. Figure 4.3 Attaching the WBS-2400/5800 to the pole bracket
Installation Guide 17 Note: The WBS-2400/5800 unit must be parallel to the ground. The unit can be rotated to obtain the correct position. Note Installations on large wooden poles require band clamps such as those supplied by Panduit, www.panduit.com. Such a product is listed as "Metal, Locking Tie Extra Heavy Duty 304 Stainless Steel". The tie and the installation tool are shown below To continue installing the WBS-2400/5800, see Grounding the Wavion WBS-2400/5800 chapter Grounding WBS-2400/5800 Sector is shown in the figure below. Figure 4.4 Grounding Method Caution: You must always install an external grounding wire. You must also ground the outdoor data protection device to a ground rod or a bonded pipe. Make sure you have completed grounding before you connect power to the WBS-2400/5800. Warning: Transient or electrostatic discharges that may occur at the WBS-2400/5800, for example a lightning strike, may damage your network equipment connected to the WBS-2400/5800 and cause personnel injury or death of persons touching the exposed metal connectors of the equipment. You must install a properly grounded lightning surge protector. Carefully follow the installation instructions provided by the manufacturer of the protection device. See
18 Wavion Networks To ground the Wavion WBS-2400/5800: The Grounding screw is located on the side panel of the outdoor unit. To connect the grounding cable: 1. Connect one end of a grounding cable to the grounding terminal and tighten the grounding screw firmly. Do the following steps: a. Remove the nut and star washers from the grounding screw. b. Attach one star washer to the grounding screw. c. Attach #10 AWG bare copper wires with an M6 terminal ring to the grounding screw. d. Attach the second star washer and tighten the nut. 2. Connect the other end of the grounding cable to a good ground (earth) connection. (For example, a grounding rod). Figure 4.5 Grounding Grounding the Data Protection Device The grounding method for an indoor data protection device is shown in Figure 4.6. To ground an indoor data protection device: 1. Position the protection device as close to the building entrance as possible. 2. Attach a length of #10 AWG bare copper wires to the ground post on the data protection device. 3. Attach the other end of the grounding wire to the ground connection of an electrical outlet or a grounded water pipe.
Installation Guide 19 Figure 4.6 Grounding indoor injector by Network Protection Unit Figure 4.7 Grounding injector that located outdoor by Network Protection Unit
20 Wavion Networks Connecting Power and DATA The following describes how to apply power and data to the WBS-2400/5800X Caution: You must always install an external grounding wire. Perform a simple continuity check between the WBS-2400/5800and the ground termination point to confirm. You must also ground the outdoor data protection device to a ground rod or a bonded pipe. Make sure you have completed grounding before you connect power to the WBS-2400/5800X. The Wavion WBS-2400/5800 is equipped with two RJ45 connectors. The right hand port named "TEST" is for engineering use only (!) and has to be sealed with the sealing rubber. Use the ETH port to connect data and power cable. Figure 4.8 Connecting PoE cable WARNING: The port named "TEST" is for engineering use only. In any case do not connect PoE source to "TEST" port (!)
Installation Guide 21 When connecting to the Ethernet port, if you need to terminate the Ethernet cable, use a standard RJ45 termination. Use a shielded RJ45 plug and be sure to connect the shield of the Ethernet cable to the shield of the RJ 45 plug. To connect to the data port: 1. Make sure that the power is turned off for the designated circuits. 2. Run shielded Category 5 Ethernet cable appropriates for outdoor use from a POE injector to the Wavion WBS-2400/5800 through the lightning protection device. See "Grounding the Data protection device" section for connection diagram. 3. Connect one end of the Category 5 cable to the "RADIO" port of the Wavion POE injector. 4. Connect the other cable end to ETH port on the WBS-2400/5800. Use a shielded RJ45 8-pin modular plug to terminate the cables at the desired lengths. 5. Place the sealing rubber on the cable and push it towards RJ45 connector on WBS-2400/5800 6. This port must be sealed with the provided rubber seal, make sure that the waterproof Seal strip is also attached. WARNING: The shields of the Cat5 cable must be properly terminated and bonded to the unit and to the protective earth (PE) at the building entrance. This provides protection against the risk of fire, electrical hazard and ensures the reliable operation of this equipment. Note: National Electrical Codes (NEC) Article 800 requires the use of an Agency Listed (UL/CSA) Building Entrance Protector for all power and communications cables entering a building. Article 800 is intended to protect the building and occupants from fires caused by transient voltage and current surges. Note: This is not a mid-span powered device. Do not attempt to daisy-chain Power Over Ethernet devices.
22 Wavion Networks Figure 4.9 Sealing rubber 7. Remove the strip nylon cover
Installation Guide 23 Figure 4.10 Sealing rubber 8. Tighten the band on sealing rubber for better sealing or using weatherproof Stripe. Figure 4.11 Weatherproof Stripe sealing 9. Connect the data cable from the network to "Ethernet" port of POE injector. 10. Connect POE injector to AC power source to power WBS-2400/5800 unit. Note: Use high quality sealing material such as Scotch® 130C Linerless Rubber (attached to the product) Splicing Tape from 3M to ensure IP-67 compliant protection against dust and water.
24 Wavion Networks POE port RJ45 Pin Descriptions Pin T/R Signal Color Description 1 T TXD+ Orange-White TX Data 10/100BaseT 2 R TXD- Orange TX Data 10/100BaseT 3 T RXD+ Green-White RX Data 10/100BaseT 4 R PoE+ Blue Power input, 55 VDC (+) 5 T PoE+ Blue-White Power input, 55 VDC (+) 6 R RXD- Green RX Data 10/100BaseT 7 T PoE- Brown-White Power input, 55 VDC (-) 8 R PoE- Brown Power input, 55 VDC (-) Safety Information for the Wavion WBS-2400/5800 The Federal Communications Commission (FCC) with its action in ET Docket 96-8 has adopted a safety standard for human exposure to RF electromagnetic energy emitted by FCC certified equipment. Proper operation of the Wavion WBS-2400/5800according to the instructions found in this manual, results in user exposure that is substantially below the FCC recommended limits. Follow these guidelines to ensure safe operation of the Wavion WBS-2400/5800X: • Do not touch or move the antennas while the unit is transmitting or receiving. • Make sure the antennas are connected when operating the radio or attempting to transmit data, otherwise, the radio may be damaged. • Do not hold the antenna to be close to or touching any exposed parts of the body, especially the face or eyes, while transmitting. • The use of wireless devices on airplanes is governed by the Federal Aviation Administration (FAA). • The use of wireless devices in hazardous locations is limited to the constraints posed by the safety directors of such environments. • The use of wireless devices in hospitals is restricted to the limits set forth by each hospital. • Do not operate a portable transmitter near unshielded blasting caps or in an explosive environment. • The Wavion WBS-2400/5800must be used only with Wavion approved components and antennas.
Installation Guide 25 Service Instructions The Wavion WBS-2400/5800 contains no user serviceable parts inside.
26 Wavion Networks Chapter 5 Product Specification WBS-2400 Sector The tables in this chapter contain specifications for the Wavion WBS-2400. Wireless Specifications compliant IEEE 802.11b/g Frequency band 2.4 - 2.483 GHz Modulation • 802.11b: DSSS (DBPSK, DQPSK, CCK) • 802.11g: OFDM (64QAM, 16QAM, QPSK, BPSK) TX Power Maximum 802.11b and 802.11g Beamformer Directed Power EIRP + Beamfroming gain: 42.5dBm EIRP Calculations Antenna Gain - 10.5 dBi Total EIRP - 34.5 dBm RX Sensitivity* 802.11b and 802.11g Antenna Array three 10.5 dBi directional antennas * RX Sensitivity -105.5 dBm @ 1 Mbps -103 dBm @ 2 Mbps -100.5 dBm @ 5.5 Mbps 96 dBm @ 11 Mbps -102.5 dBm @ 6 Mbps -100.5 dBm @ 9 Mbps -99.5 dBm @ 12 Mbps -98 dBm @ 18 Mbps -95 24
Installation Guide 27 dBm @ Mbps -92 dBm @ 36 Mbps -88 dBm @ 48 Mbps -86 dBm @ 54 Mbps Security Specifications Packet filtering via layer 2 & 3 WEP (64 bit or 128 bit) WPA: Encryption: WEP or TKIP Authentication: Pre-Shared Key or 802.1x with RADIUS Server (EAP-TLS, PEAP, EAP-TTLS) VPN pass-through and tagging HTTPS for web-based management tools Management Specifications Web based configuration and management too SNMPv2 with standard and Wavion MIB support Configuration save and restore Network and client statistics Networking and QoS Specifications Full 802.11b/g client compatibility 16 VLANs 16 SSIDs
28 Wavion Networks Physical Specifications Network Interfaces • Auto-sensing 10/100 Ethernet • Input from Wavion Injector Power Input • Power from a Wavion POE Injector. Indicator Lights • Ethernet port LED Link/Act indicator • System Status LED indicator • RF channel status indicator Physical Dimensions • Height: 9 cm • Length: 39 cm • Width: 36 cm • Weight: 4.6 Kg without mounting brackets Power Specifications • Power Input • 55VDC, supplied over Ethernet from Wavion injector. Input Power Consumption • Power from Wavion Injector max.0.8A @ 55VDC • Input power consumption for units is max. 0.45A@55V; maximal power 25W.
Installation Guide 29 Environmental Specifications Operating Temperature Range -40°C to +55°C (without Sun Shield) -40°C to +60°C (with Sun Shield) Storage Temperature Range -45°C to +85°C Weather Rating IP67 Wind Survivability 165 mph Salt and Fog Rust Resistance MIL-STD-810F 509.4 Shock and Vibration ESTI 300-192-4 spec T41.E Transportation ISTA2A Approvals RF FCC CFR 47 part 15, Sub Part C ETSI 300 328 V1.7.1 (2006) Safety TUVus EN 60950-1:2001+A11:2004 IEC 60950-1:2001 First Edition Information Technology equipment – Safety – Part 1 EMC FCC CFR 47 Part 15, Sub Part B, Class B (USA) ETSI 301 489-4 V1.3.1 (2002), ETSI 301 489-1 V1.5.1 (2003) Regulatory Compliance RoHS , CE 0682 - TBD!
30 Wavion Networks Chapter 6 Antenna 2.4GHz Specifications and Patterns The chapter describes antenna specifications and patterns for the antennas supplied with the Wavion WBS-2400. SF-245W 2.4GHz Sector Antenna 2.4GHz Flat Panel Base Station Antenna
Installation Guide 31 Antenna Electrical Specifications Number of antennas 3 Frequency Range 2.4 - 2.4835 GHz Peak Gain 2.4-2.4835 GHz 10.5 dBi (min) 0 dBi (max) design goal at all directions -8 dBi (max) design goal at all directions VSWR 1.5 :1 (max) R.L. -14 dB (max) Azimuth 3 dB Beamwidth 120° ± 3° Azimuth Ripple 3 dB (max) Azimuth Squint ± 3° Polarization Linear Vertical Elevation 3 dB Beamwidth 20° ± 1° Elevation Tilt ± 2° (max) Side Lobes Level - 12 dB (max) Side Lobes Level @ ±120° azimuth (0 degree elevation) - 20 dB (max) Cross Polarization - 15 dB (max) Front to Back Ratio - 25 dB (max) Isolation between antennas 10 to 20 dB Input Impedance 50 Ohms Input Power 6 W (max) Lighting protection DC Grounded Mechanical Dimensions (Lx W x D) 346.5 x 344.7x 44 mm (max) The antenna contour per Wavion enclosure Weight 1.2 kg (max), 1.0 kg design goal RF Connector 3x MCX female Radome Plastic color- RAL 9002 Base Plate Aluminum with chemical conversion coating Outline Drawing See attached drawing. Spacing between elements 90 mm Antenna service life 10 Years (min)
32 Wavion Networks Antenna ENVIRONMENTAL TEST STANDARD DURATION TEMPERATURE NOTES Water Tightness IEC 529 - - IP67*** Internal pressure TBD **** Solar Radiation ASTM G53 1000 h - - Flammability UL 94 - - Class HB Salt Spray IEC 68-2-11 Ka 500 h - - Ice And Snow - - - 25mm Radial Wind Speed Survival Operation - - - - - - 266 Km/h 160 Km/h Regulatory Compliance RoHS , CE 0682 Low Temperature IEC 68-2-1 72 h -45°C - High Temperature IEC 68-2-2 72 h +90°C - Temp. Cycling IEC 68-2-14 1 h -45°C +90°C 3 Cycles Vibration IEC 60721-3-4 30 min/axis - Random 4M5 Shock Mechanical IEC 60721-3-4 - - 4M5 Humidity ETSI EN300-2-4 T4.1E 144 h - 95%
Installation Guide 33 Chapter 7 Product Specification WBS-5800 The tables in this chapter contain specifications for the Wavion WBS-5800. Wireless Specifications compliant IEEE 802.11b/g Frequency band 5.725–5.850 GHz Modulation 802.11a: OFDM (64QAM, 16QAM, QPSK, BPSK) TX Power Maximum Max. power per antenna: 19dBm (FCC version - Maximum transmit power will vary by channel and data rate) Beamformer Directed Power EIRP + Beamfroming gain: 43dBm EIRP Calculations Antenna Gain – 12.5 dBi Total EIRP - 35.5 dBm RX Sensitivity* 802.11a Antenna Array Three 12.5 dBi omni-directional antennas * RX Sensitivity -102.5 dBm @ 6 Mbps -100.5 dBm @ 9 Mbps -99.5 dBm @ 12 Mbps -98 dBm @ 18 Mbps -95 dBm @ 24 Mbps -92 dBm @ 36 Mbps -88 dBm @ 48 Mbps -86 dBm @ 54 Mbps
34 Wavion Networks Management Specifications Web based configuration and management too SNMPv2 with standard and Wavion MIB support Configuration save and restore Network and client statistics Security Specifications Packet filtering via layer 2 & 3 WEP (64 bit or 128 bit) WPA: Encryption: WEP or TKIP Authentication: Pre-Shared Key or 802.1x with RADIUS Server (EAP-TLS, PEAP, EAP-TTLS) VPN pass-through and tagging HTTPS for web-based management tools Networking and QoS Specifications Full 802.11b/g client compatibility 16 VLANs 16 SSIDs
Installation Guide 35 Environmental Specifications Operating Temperature Range -40°C to +55°C (without Sun Shield) -40°C to +60°C (with Sun Shield) Storage Temperature Range -45°C to +85°C Weather Rating IP67 Wind Survivability 165 mph Salt and Fog Rust Resistance MIL-STD-810F 509.4 Shock and Vibration ESTI 300-192-4 spec T41.E Transportation ISTA2A Physical Specifications Network Interfaces • Auto-sensing 10/100 Ethernet • Input from Wavion Injector Power Input • Power from a Wavion POE Injector. Indicator Lights • Ethernet port LED Link/Act indicator • System Status LED indicator • RF channel status indicator Physical Dimensions • Height: 9 cm • Length: 39 cm • Width: 36 cm • Weight: 4.6 Kg without mounting brackets Power Specifications • Power Input • 55VDC, supplied over Ethernet from Wavion injector. Input Power Consumption • Power from Wavion Injector max.0.8A @ 55VDC • Input power consumption for units is max. 0.45A@55V; maximal power 25W.
36 Wavion Networks Approvals RF FCC CFR 47 part 15, Sub Part C Safety TUVus EN 60950-1:2001+A11:2004 IEC 60950-1:2001 First Edition Information Technology equipment – Safety – Part 1 EMC FCC CFR 47 Part 15, Sub Part B, Class B (USA)
Installation Guide 37 Antenna Electrical Specifications Number of antennas 3 Frequency Range 5.7 - 5.9 GHz Peak Gain 5.7 - 5.9 GHz 12.5 dBi VSWR 1.5 :1 (max) R.L. -14 dB (max) Azimuth 3 dB Beamwidth 120° ± 3° Azimuth Ripple 3 dB (max) Azimuth Squint ± 3° Polarization Linear Vertical Elevation 3 dB Beamwidth 20° ± 1° Elevation Tilt ± 2° (max) Side Lobes Level - 12 dB (max) Side Lobes Level @ ±120° azimuth (0 degree elevation) - 20 dB (max) Cross Polarization - 15 dB (max) Front to Back Ratio - 25 dB (max) Isolation between antennas 10 to 20 dB Input Impedance 50 Ohms Input Power 6 W (max) Lighting protection DC Grounded Mechanical Dimensions (Lx W x D) 346.5 x 344.7x 44 mm (max) The antenna contour per Wavion enclosure Weight 1.2 kg (max), 1.0 kg design goal RF Connector 3x MCX female Radome Plastic color- RAL 9002 Base Plate Aluminum with chemical conversion coating Outline Drawing See attached drawing. Spacing between elements 90 mm Antenna service life 10 Years (min) Water Tightness IEC 529 - - IP67***
38 Wavion Networks Internal pressure TBD **** Solar Radiation ASTM G53 1000 h - - Flammability UL 94 - - Class HB Salt Spray IEC 68-2-11 Ka 500 h - - Ice And Snow - - - 25mm Radial Wind Speed Survival Operation - - - - - - 266 Km/h 160 Km/h Regulatory Compliance RoHS , CE 0682 Low Temperature IEC 68-2-1 72 h -45°C - High Temperature IEC 68-2-2 72 h +90°C - Temp. Cycling IEC 68-2-14 1 h -45°C +90°C 3 Cycles Vibration IEC 60721-3-4 30 min/axis - Random 4M5 Shock Mechanical IEC 60721-3-4 - - 4M5 Humidity ETSI EN300-2-4 T4.1E 144 h - 95% ENVIRONMENTAL TEST STANDARD DURATION TEMPERATURE NOTES
Installation Guide 39 Chapter 8 Antenna 5.8GHz Specifications and Patterns The chapter describes antenna specifications and patterns for the antennas supplied with the Wavion WBS-5800. MT-463009CV 5.8GHz Antenna Azimuth Patterns directional Antenna
40 Wavion Networks MT-463009CV 5.8GHz Antenna Elevation Patterns
Installation Guide 41 Chapter 9 Installation Accessories This chapter describes the accessories available for the WBS-2400 and ordering information. The following topics are covered in this chapter: • Ethernet Cables • Sun Protection • Lightning Protection • Power Over Ethernet
42 Wavion Networks Ethernet Cables Description Manufacturer Part Number Distributor Contact Information Outdoor CAT5e double jacket 4-pair data cable Teldor 8393204101 G.Bares Tel: +972-(4)-8215450 Sun Protection Description Product Name Part Number Sun Shield for WBS-2400/5800X, extends upper operation temperature range to +60°C WA-SUN-SH 27009023 Lightning Protection Description Manufacturer Part Number Contact Information Data protection device Hyperlink HGLN-CAT5-2 www.hyperlinktech.com Power Over Ethernet Description Product Name Part Number Wavion Injector for powering the WBS-2400/5800over an Ethernet cable. Output 55VDC, 1A. WPI-AC-55W 27002213
Installation Guide 43 Chapter 10 Wind Loading Considerations This chapter describes wind loading considerations for the WBS-2400/5800X. Note: It is recommended to evaluate the static and dynamic load bearing capabilities for each assembly and installation individually. It is your responsibility to evaluate the load bearing capabilities of the structure. The Wavion WBS-2400/5800weighs approximately 16 lbs, including all mounting hardware. When the Wavion WBS-2400/5800is mounted on a pole, the sail area of the WBS-2400/5800is approximately 1 square foot. The Wavion WBS-2400/5800can load a pole with a maximum load of 3400 Newton in wind conditions of 165mph.
44 Wavion Networks Chapter 11 Acronyms Acronym Description 2P Two-Phase or Split Phase 2W Two-Wire 3W Three-Wire AC Alternating Current ANSI American National Standards Institute AWG American Wire Gauge C Celsius CAT Category CCK Complementary Code Keying CFR Code of Federal Regulations CSA Canadian Standard Association dB Decibels dBi Decibels Relative to an Isotropic Radiator DBPSK Differential-Binary Phase-Shift Keying DC Direct Current DQPSK Differential-Quadrature Phase-Shift Keying DSSS Direct-Sequence Spread Spectrum EMC Electromagnetic Compatibility EN IEC standard ESD Electrostatic Discharge FCC Federal Communications Commission Hz Hertz HPoE High Power over Ethernet IEEE Institute of Electrical and Electronics Engineers IP67 Ingress Protection Standard ISTA International Safe Transit Association LAN Local Area Network
Installation Guide 45 Mbps Megabits Per Second MHz Megahertz MIL-STD Military Standard N Neutral NEC National Electrical Codes NEMA National Electrical Manufacturers Association OFDM Orthogonal Frequency Division Multiplexing P Phase PE Protective Earth PoE Power over Ethernet RJ45 Registered Jack 45 RSS Received Signal Strength Rx Receive RXD Receive Data TUV Technical Inspection Association Tx Transmit TXD Transmit Data UL Underwriters Laboratories VAC Voltage (Alternating Current) VCCI Voluntary Control Council for Interference VDC Voltage (Direct Current) W Watts
46 Wavion Networks Chapter 12 Appendix A: WBS-2400/5800 Product list Part Number Product namer Product description TBD12406101 WBS-2400-FCC Spatially adaptive, multi radio 2.4GHz WiFi base station, 6 antenna FCC/TUV compliant 12406102 WBS-2400-EU Spatially adaptive, multi radio 2.4GHz WiFi base station, 6 antenna ETSI / CE compliant 12406104 WBS-2400-IL Spatially adaptive, multi radio 2.4GHz WiFi base station, 6 antenna Israel compliant 15806101 WBS-5800-FCC Spatially adaptive, multi radio 5.8GHz WiFi base station, 6 antenna FCC/TUV compliant

Navigation menu