Wayne Dalton 02-3039 User Manual KWT

Download:
Mirror Download [FCC.gov]
Document ID	102502
Application ID	HQWqMqcY7nQrBcejWgRzOw==
Document Description	KWT User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	66.1kB (826225 bits)
Date Submitted	2000-05-30 00:00:00
Date Available	2000-08-31 00:00:00
Creation Date	2000-05-24 09:02:01
Producing Software	Acrobat 4.0 Import Plug-in for Windows
Document Lastmod	2000-05-24 09:04:59
Document Title	KWT User manual
Document Creator	Acrobat 4.0 Import Plug-in for Windows

INSTRUMENT SPECIALTIES CO., INC. — WORLD COMPLIANCE CENTER
EMC MEASUREMENT/TECHNICAL REPORT
FCC PART 15 Certification Submiflal and
Grant of Equipment Authurization Subminal
For: Martec Access Products, Inc.
FCC ID Number: KJ802-3039
Document No.
Revision
ISSUE Date
112384-A-FCC
1 May 2000
EXHIBIT 7 — Operating Instructions
2 pages of operating instructions
RMT Assoc. KWT INSTRUCTIONS v1.1
KWT OPERATION with software ver 1.8
ISSUING DOOR CONTROL COMMANDS
To issue door control command do as follow:
1. Enter the four digit user code. If a single door was being supported then the door number
need not be entered. The four digit access code would Stan/stop the door. (Keypresses are confirmed
by theyellow LED.)
2. lfsupporting more then one door then enter the door number <1 .. 4> at this
time.
3. The green LED will turn on after the correct code is entered. For up to 20 seconds ifany key is
pressed a toggle command would be sent to the same door.
4. ll'a mistake was made while entering the password then the Re-starl key can he pressed to start
entering the code from the begining. The keypad is active for 30 seconds afler the last key was
pressed.
The KWT will not acknowledge keypresses after 5 digit invalid code entry.
CHANGING USER CODE
(The RF code will remain the same address)
There are two ways to change the user code via current user code or via system code.
The default code alter manufacturing is 1234,
CHANGING USER CODE IF CURRENT USER CODE IS KNOWN
l- Enter the " key,
24 Enter the four digit user access code.
3- Enter the ‘ key, The yellow LED will flash three times to acknowledge entry into the
programming mode.
4- Enter the new 4 digit user code.
5- Enter the number ofdoors supported .
l = A single door
2 = 2 doors
3 e 3 doors
4 = 4 doors
6- Enter the it key. theyellow LED will flash three times.
The new code was learned.
CHANGING USER CODE IF CURRENT USER CODE IS NOT KNOWN
(The RF code will automatically change to new addresses.)
1- Enter the " key
2- Enter the four digit system code {9999}
3— Enter the ‘ key. The yellow LED will flash three times to acknowledge entry into the
programming mode,
4- Enter the new 4 digit user code.
5- Enter the number of doors supported <1 .. 4>,
I Z A single door
doors
3 f 3 doors
4 = 4 doors
6- Enter the # key. the yellow LED will turn on steady for 2 seconds. then it will
flash two times. The new code was Icamed.
If at any time during the programing mode an error was made to rc-start, hit the Re-start key.
RMT Assoc. KWT INSTRUCTIONS v1.1
KWT OPERATION with software ver 1.8
RE-STA RT KE Y
The Re-slart key allows the user to enter a door command for a different door or go imp programming mode
at any time during the keypad operation. The re-slan also applies power the first time the keypad is going to
be used. Power will remain on for 30 seconds afier the last key was pressed.
LOW BATT E RV
When the Re-slarl key is pressed and a low battery condition is present the yellow LED will blink until
either a key is pressed or the 30 second timeoul for the power is reached.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Modify Date                     : 2000:05:24 09:04:59-04:00
Create Date                     : 2000:05:24 09:02:01-04:00
Creator                         : Acrobat 4.0 Import Plug-in for Windows
Producer                        : Acrobat 4.0 Import Plug-in for Windows
Page Count                      : 3

EXIF Metadata provided by EXIF.tools