Weber 261001, BLACK User Manual SUMMIT 425 LP, OUTDOOR GRILL Manuals And Guides L0608784
WEBER Grill, Gas Manual L0608784 WEBER Grill, Gas Owner's Manual, WEBER Grill, Gas installation guides
User Manual: Weber 261001, BLACK 261001, BLACK WEBER SUMMIT 425 LP, OUTDOOR GRILL - Manuals and Guides View the owners manual for your WEBER SUMMIT 425 LP, OUTDOOR GRILL #261001BLACK. Home:Lawn & Garden Parts:Weber Parts:Weber SUMMIT 425 LP, OUTDOOR GRILL Manual
Open the PDF directly: View PDF 
.
Page Count: 20
| Download | |
| Open PDF In Browser | View PDF |
SUMMIT M425 & 450 LP Gas Barbecues Operating Guide Summit 450 LP Summit 425 LP 1 Serial Number Serial Number I'b I a "t I)t_lC_' ,,I,,l'lI_.TI.L_ ,It _ Idl I I WARNING: Follow all leak check procedures carefully in this manual prior to barbecue operation. Do this even if barbecue was dealer assembled. NOTICE TO INSTALLER: These instructions must be left with the owner and the owner should keep them for future FOR YOUR SAFETY 1. Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. 2. An LP tank not connected for use shall not be stored in the vicinity any other appliance. use. FORYOUR THIS GAS APPLIANCE OUTDOOR USE ONLY. of this or IS DESIGNED FOR WARNING: Do not try to light this appliance without reading "Lighting" instructions section of this manual. SAFETY If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. Open lid. 4. If odor continues, immediately call your gas supplier or your fire department. 97672 4/97 WARNINGS DANGER Failure to follow the Dangers,Warnings and Cautions contained in this Owner's Manual may result in serious bodily injury or death, or a fire or an explosion causing damage to property. Do not store a spare or disconnected LP tank under or near this barbecue. Should a grease fire occur, turn off all burners and leave lid closed until fire is out. Improper assembly may be dangerous. Please carefully follow the assembly instructions in this manual. Do not enlarge valve orifices or burner ports when cleaning the valves or burners. After a period of storage, and/or nonuse, the Weber Gas Barbecue should be checked for gas leaks and burner obstructions before using. See instructions in this manual for correct procedures. The Weber Gas Barbecue should be thoroughly cleaned on a regular basis. LP gas is not natural gas. The conversion or attempted use of natural gas in an LP unit or LP gas in a natural gas unit is dangerous and will void your warranty. Do not operate the Weber Gas Barbecue if there is a gas leak present. Do not attempt to disconnect any gas fitting while your barbecue is in operation. Do not use a flame to check for gas leaks. Combustible materials should never be within Use heat-resistant barbecue mitts or gloves when operating barbecue. 24 inches of the top, bottom, back or sides of your Weber Gas Barbecue. • Do not put a barbecue cover or anything flammable on or in the storage area under the barbecue. • Your Weber Gas Barbecue should never be used • • This barbecue is for residential use only. LP GAS UNITS ONLY: by children. • You should exercise reasonable care when operating your Weber Gas Barbecue. tt will be hot during cooking or cleaning, and should never be left unattended. Use the regulator that is supplied with your Weber Gas Barbecue. • Do not attempt to disconnect the gas regulator or any gas fitting while your barbecue is in operation. Should the burners go out during operation, turn all gas valves off. Open the lid and wait five minutes before attempting to relight, using the lighting instructions. • A dented or rusty LPtank may be hazardous and should be checked by your liquid propane supplier. Do not use an LP tank with a damaged valve. Do not use charcoal or lava rock in your Weber Gas Barbecue. • Although your LP tank may appear to be empty, gas may still be present, and the tank should be transported and stored accordingly. • If you see, smell or hear the hiss of escaping gas from the LP tank: Never lean over open grill or place hands or fingers on the front edge of the cooking box. 1. Get away from LP tank. 2. Do not attempt to correct the problem yourself. 3. Call your fire department. TABLE OF CONTENTS Warnings 2 Steam-N-Chips Warranty 4 Maintenance A Word of Thanks 4 Standards and Codes Information 5 Operating Area Storage *REFER TO YOUR STEP-BY-STEP THIS TIME Lighting Crossover Ignition System To Extinguish 5 5 SECTION AT Smoker Spider Stopper Guards Inspection and Cleaning of the Spider Stopper Guards Main Burner Flame Pattern Main Burner Cleaning Procedure Replacing the Main Burners Crossover Ignition System Operations 6 Troubleshooting 6 6 Exploded Views and Replacement Parts Lists Manual Lighting 7 To Extinguish 7 Cooking 8 Storage 8 Cleaning 8 Summit 425 LP Summit 450 LP Patents and Trademarks 9 10-12 10 10 11 11 11 13 14 16-19 16-17 18-19 20 WARRANTY Weber-Stephen Products Co. (Weber) hereby warrants to the ORIGINAL PURCHASER of this Weber Gas Barbecue that it will be free of defects in material and workmanship from the date of purchase as follows: Aluminum Castings, 25 years, Cooking Grates and Flavorizer Bars, 7 years, All Remaining Parts, 5 years, when assembled and operated in accordance with the printed instructions accompanying it. Weber may require reasonable proof of your date of purchase. THEREFORE, YOU SHOULD RETAIN YOUR SALES SLIP OR INVOICE. This Limited Warranty shall be limited to the repair or replacement of parts which prove defective under normal use and service and which on examination shall indicate, to Weber's satisfaction, they are defective. Before returning any parts, contact Weber-Stephen Products Co. Customer Service Center. If Weber confirms the defect and approves the claim, Weber will elect to replace such parts without charge. If you are required to return defective parts, transportation charges must be prepaid. Weber will return parts to the purchaser, freight or postage prepaid. This Limited Warranty does not cover any failures or operating difficulties due to accident, abuse, misuse, alteration, misapplication, vandalism, improper installation or improper maintenance or service, or failure to perform normal and routine maintenance, including but not limited to damage caused by insects within the burner tubes, as set out in this owner's manual. Deterioration or damage due to severe weather conditions such as hail, hurricanes, earthquakes or tornadoes, acid rain, discoloration due to exposure to chemicals either directly or in the atmosphere, is not covered by this Limited Warranty. There are no other express warrants except as set forth herein and any applicable implied warranties of merchantability and fitness are limited in duration to the period of coverage of this express written Limited Warranty. Some states do not allow limitation on how long an implied warranty lasts, so this limitation may not apply to you. Weber is not liable for any special, indirect or consequential damages. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion may not apply to you. Weber does not authorize any person or company to assume for it any other obligation or liability in connection with the sale, installation, use, removal, return, or replacement of its equipment; and no such representations are binding on Weber. This Warranty applies only to products sold at retail. A WORD Thank you highest OF THANKS for choosing quality products error may parts or assembly. serial occur. number regarding our a Weber Our for your Call our Palatine, (888) toll free number. products. We wish the best Road IL 60067-6266 at Weber we give much For quicker We also Company here Service for reference. you family While Customer available 33-SUMMIT (888-337-8664) Our satisfaction. knowledgeable Weber-Stephen Products Customer Service Center 200 E. Daniels Barbecue. welcome in outdoor staff has worked attention is prepared service, please any comments cooking to our to help have hard your products, you with owner's or suggestions enjoyment. to produce you the an occasional any problems manual might and have with STANDARDS AND CODES INFORMATION Your Weber Gas Barbecue is a portable outdoor cooking appliance. With the Weber Gas Barbecue you can grill, barbecue, roast and bake with results that are difficult to duplicate with indoor kitchen appliances. The closed lid and Flavorizer Bars produce that "outdoor" flavor in the food. The Weber Gas Barbecue is portable so you can easily change its location in your yard or on your patio. Portability means you can take your Weber Gas Barbecue with you if you move. Liquid Propane (LP) gas supply is easy to use and gives you more cooking control than charcoal fuel. • The entire cooking box gets hot when in use. Do not leave unattended. • Keep any electrical supply cord and the fuel supply hose away from any heated surface. • Keep the cooking area clear of flammable vapors and liquids, such as gasoline, alcohol, etc., and combustible materials. • Never store an extra (spare) LP tank under or near the Weber Gas Barbecue. Storage • These instructions will give you the minimum requirements for operating and maintaining your Weber Gas Barbecue. Please read the instructions carefully before using your Weber Gas Barbecue. Improper assembly can be dangerous. The gas must be turned off at the LP tank when the Weber Gas Barbecue is not in use. • When the Weber Gas Barbecue is stored indoors, the gas supply must be DISCONNECTED and the LP tank stored outdoors in a well-ventilated space. • Not for use by children. • LP tanks must be stored outdoors in a well-ventilated • If there are local codes that apply to portable gas grills, you will have to conform to them. tf there are no local codes, you must conform to the latest edition of the National Fuel Gas Code: ANSI Z 223.1. • • • • The pressure regulator supplied with the Weber Gas Barbecue must be used. This regulator is set for 10.5 inches of water column (pressure). This Weber Gas Barbecue is designed for use with liquid propane (LP) gas only. Do not use with natural (piped in city) gas. The valves, orifices, hose and regulator are for LP gas only. area out of reach of children. Disconnected LP tanks must not be stored in a building, garage or any other enclosed area. • Weber Gas Barbecue, the appliance and LP tank must be kept outdoors in a well-ventilated space. • The Weber Gas Barbecue should be checked for gas leaks and any obstructions in the burner tubes before using. (See Maintenance Section) • Check that the areas under the control panel and the bottom tray are free from debris that might obstruct the flow of combustion or ventilation air. • The Spider Stopper Guards should also be checked for any obstructions. Refer to Maintenance Section. Do not use with charcoal fuel. For Installation in Canada These instructions, while generally acceptable, do not necessarily comply with the Canadian Installation codes, particularly with piping above and below ground. In Canada the installation of this appliance must comply with local codes and/or Standard CAN/CGA-B149.2 (Installation Code for Propane Burning Appliances and Equipment). Operating area WARNING: Onlv use this barbecue outdoors in a well ventilated area. Do not use in a garage, building, breezeway or any other enclosed area. • Never use your Weber Gas Barbecue under an unprotected combustible roof or overhang. • Your Weber Gas Barbecue is not intended to be installed in or on recreational vehicles and/or boats. • Keep this grill away from combustible materials when in use at a minimum of 24 inches of the top, bottom, back or sides. When the LP tank is not disconnected from the REFER TO YOUR STEP-BYSTEP GUIDE AT THIS TIME FOR BARBECUE ASSEMBLY WARNING: Make sure your barbecue is set up properly and leak checked before attempting to operate. LIGHTING EACH HEAT ZONE OPERATES INDEPENDENTLY. 1) Open the lid. Figure 1. Summary lighting instructions are on the control panel. 2) Check that the fuel scale reads more than "E". Note - E = empty; F = full. 3) Make sure all burner control knobs are OFF. (Push each burner control knob down and turn clockwise.) High Crossover Medium Ignition Low Off System DANGER Failure to open lid while igniting the barbecue, or not waiting 5 minutes to allow the gas to clear if the barbecue does not light, may result in an explosive flame-up which can cause serious bodily injury or death. Note - The Crossover Ignition System ignites the Left burner of each heat zone with a spark from the igniter electrode inside the Gas Catcher Ignition Chamber. You generate the energy for the spark by pushing the Crossover Ignition Button until it clicks. WARNING: Check hose before each use of barbecue for nicks, cracking, abrasions or cuts. If the hose is found to be damaged in any way, do not use the barbecue. Contact your dealer. WARNING:The storage space under the cooking module is intended for storage of nonflammable items only. Crossover Ignition System WARNING: The burner control knobs must be in the OFF position before turning on the LP tank valve. If they are not in the OFF position, when you turn on the LP tank valve, the excess flow control will activate, limiting the flow of gas from the LP tank. If this should occur, turn OFF the LP tank valve and burner control knobs and start over. DANGER When the excess flow control is activated, a small amount of gas is still flowing to the burners. After turning OFF the tank and burner control knobs, wait at least 5 minutes for the gas to clear before attempting to light the barbecue. Failure to do so may result in an explosive flame-up which can cause serious bodily injury or death. 4) Turn the tank on by turning the tank valve counterclockwise. WARNING: Do not lean over open barbecue. Keep your face and body at least one foot away from the matchlight hole when lighting the barbecue. 5) Select Heat Zone. 6) Push LEFT burner control knob down and turn to START/HI. 7) Push the Crossover Ignition Button several times, so it clicks each time. 8) Check that the burner is lit by looking through the matchlight hole above the burner control knob. WARNING: If the burner does not light, turn the LEFT burner control knob to OFF and wait 5 minutes to let the gas clear before you try again or try to light with a match. 9) After the LEFT burner is lit you can turn on the RIGHT burner. Note - Always light the LEFT burner firsL The RIGHT burner ignites from the LEFT burner. 2 Figure 1 TO EXTINGUISH Turn gas supply OFF at the source, then push down and turn each burner control knob clockwise to OFF. MANUAL LIGHTING EACH HEAT ZONE OPERATES INDEPENDENTLY. DANGER When the excess High Medium Low Off DANGER Failure to open lid while igniting the barbecue, or not waiting 5 minutes to allow the gas to clear if the barbecue does not light, may result in an explosive flame-up which can cause serious bodily injury or death. 1) Open the lid. Figure 2. 2) Check that fuel scale reads more than "E". Note - E = empty; F = furl. 3) Make sure all burner control knobs are turned OFF. (Push each burner control knob down and turn clockwise.) WARNING: The burner control knobs must be in the OFF position before turning on the LP tank valve. If they are not in the OFF position, when you turn on the LP tank valve, the excess flow control will activate, limiting the flow of gas from the LP tank. If this should occur, turn OFF the LP tank valve and burner control knobs and start over. flow control a small amount of gas is still flowing to the burners. After turning OFF the tank and burner control knobs,wait at least 5 minutes for the gas to clear before attempting to light the barbecue. Failure to do so may result in an explosive flame-up which can cause serious bodily injury or death. 4) Turn the tank on by turning the tank valve counterclockwise. 5) Select heat zone. 6) Put a match in the match holder and strike the match. 7) Insert match holder and lit match through matchlight hole to ignite LEFT burner. Figure 3. WARNING: Do not lean over open barbecue. Keep your face and body at least one foot away from the matchlight hole when lighting the barbecue. 8) Push LEFT burner control knob down and turn to H (high). matchlight hole in control panel Hole in cooking WARNING:The storage space under the cooking module is intended for storage of nonflammable items only. Manual Lighting is activated, box assembly Control panel Left burner tube Figure 3 9) Observe if LEFT burner has ignited by looking through matchlight hole. WARNING: If LEFT burner fails to ignite turn LEFT burner control knob to OFF and wait 5 minutes before attempting to ignite again. 10) After the LEFT burner is lit you can turn on the RIGHT burner. Note: Always light the LEFT burner firsL The RIGHT burner ignites from the LEFT burner. \2 Figure 2 TO EXTINGUISH Turn gas supply OFF at the source, then push down and turn each burner control knob clockwise to OFF. COOKING CLEANING The Weber Gas Barbecue should not be moved when CAUTION: Turn your Weber Gas Barbecue OFF and wait for it to cool before cleaning. operating or hot. High Medium Low Off You can adjust the LEFT and RIGHT burners as desired. The control settings High (H), Medium (M), Low (L), or Off (O) are described in your Weber cookbook. The cookbook uses these notations to describe the settings of the LEFT and RIGHT burners. Note: Cooking conditions may require the adjustment of the burner controls. If burners go out during cooking, turn off all burners and wait 5 minutes before relighting. CAUTION: Check the bottom tray for grease build-up before each use. Remove excess grease to avoid a grease fire in the bottom tray. STORAGE The gas must be turned off at the LP cylinder when the Weber Gas Barbecue is not in use. When the Weber Gas Barbecue is stored indoors, the gas supply must be DISCONNECTED and the LP cylinder stored outdoors in a well-ventilated space. • LP cylinders must be stored outdoors in a wellventilated area out of reach of children. Disconnected LP cylinders must not be stored in a building, garage or any other enclosed area. • When the LP cylinder is not disconnected from the Weber Gas Barbecue, the appliance and LP cylinder must be kept outdoors in a well-ventilated space. • The Weber Gas Barbecue should be checked for gas leaks and any obstructions in the burner tubes before using. (See Maintenance Section.) • Check that the areas under the control panel and the bottom tray are free from debris that might obstruct the flow of combustion or ventilation air. CAUTION: Do not clean your Flavorizer Bars or cooking grills in a self-cleaning oven. Replacement cooking grates and Flavorizer Bars are available through your retailer or the Weber-Stephen Customer Service Center. Outside surfaces - Use a warm soapy water solution. CAUTION: Do not use oven cleaner, abrasive cleansers (kitchen cleansers) cleaners that contain citrus products or abrasive cleaning pads on barbecue or cart surfaces. Bottom tray - Remove excess grease and then wash with warm soapy water. Flavorizer Bars and Cooking Grates - Clean with a suitable brass bristle brush. As needed, remove from grill and wash with warm soapy water. Catch pan - Disposable foil trays are available, or you can line the catch pan with aluminum foil. To clean the catch pan, wash with warm soapy water. Thermometer - Wipe with warm soapy water, clean with plastic scrub ball. Do not put in dishwasher or submerge in water. Inside cooking module - Brush any debris off of burners tubes. DO NOT ENLARGE BURNER PORTS (OPENINGS). Wash inside of cooking box with warm soapy water. Inside lid - While lid is warm, wipe inside with paper towel to prevent flaking due to grease build-up. Stainless steel surfaces soap and water solution. - Wash with a soft cloth and USING THE STEAM-N-CHIPS The Steam-N-Chips Smoker cooks with both Weber FireSpice Wood Chips and Chunks. For best results with faster cooking foods like steaks, burgers and chops, etc., we recommend using the FireSpice Chips because they ignite and create smoke faster. For longer cooking foods such as roasts, chicken and turkeys, etc., we recommend using FireSpice Chunks because they ignite slowly and provide smoke for a longer period of time. As you gain experience in using your Steam-N-Chips Smoker, we encourage you to experiment with different combinations of FireSpice Chips and Chunks to find the smoke flavor that best suits your taste. To use the Steam-N-Chips Smoker As a starting point, place a handful of FireSpice Chips or a few FireSpice Chunks in the bottom of the smoker body. Figure 4. Since the chunks vary in size, place as many as you can in the smoker allowing room for the water pan. As you gain experience in smoking, increase or decrease the amount of wood to suit your taste. Fill water pan, place it in the smoker and close the smoker lid. Water __ Steam-N-Chips Pan Body Figure 4 Light the barbecue and preheat with all burners on HIGH, lid down, for 10 minutes or until the thermometer registers 500°F - 550°F. Adjust the burners for cooking; MM or LL will be your best settings for long duration smoking. Smoke will start in approximately 10 minutes and last as long as 45 minutes. If you require more smoke flavor, refill the smoker with FireSpice Chips and/or Chunks and refill the water pan with water. The Steam-N-Chips Smoker may be used to enhance any of the meat, poultry and fish recipes in the gas barbecue cookbook. Cook with the lid down according to the times indicated in charts or recipes. Note - After refilling smoker, smoke will take about 10 to 15 minutes to start again. SMOKER DANGER Do not use any flammable fluid in the Steam-N-Chips Smoker to ignite the wood. This will cause serious bodily injury. Cleaning the Steam-N-Chips Smoker Before each use, empty the Steam-N-Chips ash to allow proper air flow. Smoker of Note - Smoking will leave a "smoke" residue on the surface of the smoker. This residue cannot be removed and will not affect the function of the Steam-N-Chips Smoker. To a lesser degree a "smoke" residue will accumulate on the inside of your Weber Gas Barbecue. This residue need not be removed and will not adversely affect the function of your Weber Gas Barbecue. MAINTENANCE Spider Stopper We recommend that you inspect the Spider Stopper Guards at least once a year. Also inspect and clean the Spider Stopper Guards if any of the following symptoms should ever occur. Guards Your Gas Barbecue, as well as any outdoor gas appliance, is a target for spiders and other insects. They can nest in the venturi section of the burner tubes. This blocks the normal gas flow, and can cause the gas to flow back out of the air shutter. Figure 5. This could result in a fire in and around the air shutters, under the control panel, causing serious damage to your barbecue. Venturi I Air shutter Venturi fin 1. The smell of gas in conjunction with the burner flames appearing yellow and lazy. 2. Barbecue does not reach temperature. 3. Barbecue heats unevenly. 4. One or more of the burners do not ignite. DANGER II_ I / Failure to correct these symptoms may result in a fire which can cause serious bodily injury or death and cause damage to property. Figure 5 The Spider Stopper Guard is factory installed. It fits tightly around the air shutter section of the burner tube and the valve, thereby preventing spiders and other insects access to the burner tubes through the air shutter openings. Figure 6. Inspection and Cleaning Stopper Guards of the Spider To inspect the Spider Stopper Guards, remove the control panel and look to see if they have dust or dirt on their outside surfaces. If they are dirty, brush off the outside surface of the Spider Stopper Guards with a soft bristle brush (an old toothbrush for example). Check that there are no gaps in the Spider Stopper Guards' seams or in the fit around the burners or valves. Weber Spider Stopper Guard Figure 6 10 MAINTENANCE Main Burner Flame Pattern Replacing The Weber Gas Barbecue burners have been factory set for the correct air and gas mixture. The correct flame pattern is shown in Figure 7. Tips occasionally Burner inside cooking box j,__" yellowish Your Weber Gas Barbecue must be OFF and cool. 2. Turn OFF gas at source. 3. Disconnect regulator. 4. To remove control panel refer to "Remove the control panel and the front panel" in the Step-By-Step Guide. 5. 6. Remove cooking grates. Remove Flavorizer bars. 7. Remove the manifold by unsnapping the clips at the right and left front of the cooking box. Figure 10. Light blue " Flames Dark Main Burners 1. blue Figure 7 If the flames do not appear to be uniform the length of the burner tube, follow the burner cleaning procedures. Main Burner Cleaning Procedure Turn off the gas supply. Remove the manifold. Look inside each burner with a flashlight. Figure 8. f Clean the inside of the burners with a wire (a straightened out coat hanger will work). Figure 9. Check and clean the air shutter opening at the ends of the burners. Check and clean the valve orifices at the base of the valves. Use a brass bristle brush to clean outside of burners. This is to make sure all the burner ports are fully open. Figure 10 . Disconnect white and black wire from each igniter. Figure 11. / Figure 9 White wire, CAUTION: Do not enlarge the burner ports when cleaning. Black wire Figure 11 11 MAINTENANCE 9. Unlatch the Spider Stopper Guards and remove. Figure 1? 11. Slide the burner assembly from each Heat Zone. The left and right burners are connected by the Crossover tube. Figure 14 (a). Pull out of here Cro5 Figure 12 10. Pull the manifold out of the burners. Figure 13. Manifold Pigure Figure 13 12 14 MAINTENANCE 12. Lift and twist the burner assembly slightly to separate the crossover tube from the burners. Remove the 14. Reinstall the Spider Stopper Guards. Slightly rotate the Spider Stopper Guards so that the seams are in line with the Venturi fins. There should be no gaps in the seams or in the fit around the burners and valves. burners from the cooking box. Figure 15. Separate here Figure 17. /-,/\ Check fit around valve _3.___C r__sover Venturi tube fin Figure 15 Check fit around burner 13. To reinstall the burners, reverse steps 3 through 12. Figure CAUTION: The burner openings must be positioned properly over the valve orifices. Figure 16 (a). Check proper assembly before fastening manifold in place. Figure 16 (b). 17 Crossover Ignition System Operations If the Crossover Ignition System fails to ignite the Left burner, light the Left burner with a match. If the Left burner lights with a match, then check the Crossover Ignition System. (a) Valve • Check that both the white and black ignition wires are attached properly. Figure 18. • Check that the Crossover Ignition button pushes the igniter (button) down, and returns to the up position. • Check to see if the igniter is loose in the frame. Tighten if necessary; See Step "Install igniter" for correct procedure. Burner Orifice If the Crossover Ignition System still fails to light, contact Weber-Stephen Customer Service. White wire .., Black Figure 16 Figure 18 13 TROUBLESHOOTING Problem Check Cure Burners bum with a yellow or orange flame, in conjunction with the smell of gas. Inspect Spider Stopper Guards for possible obstructions. (Blockage of holes.) Clean Spider Stopper Guards. (See Maintenance Section.) Burners do not light. -orBurners have a small flickering flame in the HIGH position. -orBarbecue temperature only reaches 250 ° to 300 ° degrees in the HIGH position. The excess flow safety device, which is part of the barbecue to tank connection, may have activated. To reset the excess flow safety device turn all burner control knobs and the tank valve OFF. Disconnect the regulator from the tank. Turn burner control knobs to HIGH. Wait at least 1 minute. Turn burner control knobs OFF. Reconnect the regulator to the tank. Turn tank valve on slowly. Refer to Lighting Section. Burner does not light, or flame is low in HIGH position. Experiencing flare-ups: Is LP fuel low or empty? Refill LP tank. Is fuel hose bent or kinked? Straighten fuel hose. Does the Left burner light with a match? If you can light the Left burner with a match, then check the Crossover Ignition System. Are you preheating barbecue in the prescribed manner? All burners on high for 10 to 15 minutes for preheating. Are the cooking grates and Flavorizer Bars heavily coated with burned-on grease? Clean thoroughly. (See Cleaning Section.) CAUTION: Do not line the bottom tray with aluminum foil. Is the bottom tray "dirty" and not Clean bottom tray. allowing grease to flow into catch pan? Burner flame pattern is erratic. Flame is low when burner is on HIGH. Flames do Are burners clean? Clean burners. (See Maintenance Section.) Check adjustment of fuel scale. Fuel scale must be adjusted with an empty tank. not run the whole length of the burner tube. Fuel scale shows that there is gas in the LP tank, but tank is empty, If problems cannot be corrected by using these methods, please contact Weber-Stephen Customer Service. 14 15 EXPLODED VIEW FOR THE SUMMIT 425 LP 33 34 35 3S .37 6 11-15 16 17 18 19 20 4O 41 42 21 43 44 45 46 47 48 48 27 50-53 28 30 31 32 16 REPLACEMENT 1 2 PARTS LIST FOR THE SUMMIT Lid Thermometer 55 56 1/4-20 x 1 3/4 inch bolt 1/4-20 hex nut 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 Steam-N-Chips smoker Stainless steel work surface (2) Condiment holder (2) Cooking box Crossover tube (2) Left burner (2) Right burner (2) Burner control knobs (4) Igniter (2) Igniter lock nut (2) Igniter wire (white) (2) Igniter wire (black) (2) Gas catcher ignition chamber (2) Spider stopper guard (4) Manifold assembly Manifold mounting clips (2) Control panel Igniter button (2) Front panel Tool holder (4) Caster frame 57 58 59 Regulator mounting bracket Hose / regulator LP tank 60 Filler adapter 24 25 1/4-20 x 3 1/2 inch bolt (4) Match holder and chain 26 27 28 29 30 31 32 Bottom tray Catch pan holder Catch pan Drip pan (2) Caster (2) Bottom connector (2) Stainless steel bottom shelf 33 34 35 36 37 38 39 40 41 42 43 44 45 46 Warm-up rack Cooking grates (2) Flavorizer bar / cooking grate holder (2) Flavorizer bar (7) Hair pin cotter (2) Clevis pin (2) Corrugated gas line Hose adapter Top left frame Top right frame Back panel Nylon washer (8) 1/4-20 x 1/2 inch bolt (4) Wheel frame 47 48 49 50 51 1/4-20 wing nuts (2) Wheel hubcap (2) Wheel (2) Cylinder glides (2) Glide axle 52 53 54 Glide hubcaps (2) Cylinder panel Fuel scale assembly 425 LP All items are single quantities unless otherwise specified. Parts can be ordered directly from Weber-Stephen Products Company by phone or mail. Note - Do not return parts to Weber-Stephen Products Co. without first contacting the Customer Service Center by phone or marl. Returning the part may not be necessary. While we give much attention to our products, unfortunately an occasional error may occur. If a part is missing, do not go back to the store. Call the Weber Customer Service Center toll free 1-888-33-SUMMIT (1-888-337-8664) to receive immediate assistance. Have your owner's manual and serial number of the barbecue available for reference. Weber-Stephen Products Company Customer Service Center 250 South Hicks Road Palatine, IL 60067-6241 (888) 33-SUMMIT (888-337-8664) WARNING: Use only Weber factory authorized parts.The use of any part that is not factory authorized can be dangerous. This will also void your warranty. 17 EXPLODED VIEW FOR THE SUMMIT 450 LP 2 3 4 5' 3_ 4O 41 42 8 ¸ 9 10, 11 12 13-17 18 18, 20 22, 44 45 46 47 4,9 24 25 26' 27 28, 29 30 31 32 49 5O 51 49 54-57 59 83 61 3G G_ 37 38 REPLACEMENT 1 2 PARTS LIST Lid Thermometer 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Cooking grate (2) Flavorizer bar / cooking grate (2) Flavorizer bar (7) Stainless steel work surface (2) Condiment holder (2) Cooking box Crossover tube (2) Left burner (2) Right burner (2) Burner control knob (4) Igniter (2) Igniter lock nut (2) Igniter wire (black) (2) Igniter wire (white) (2) Gas catcher ignition chamber (2) Spider stopper guard (4) Manifold assembly Manifold mounting clips (2) Control panel Igniter button (2) Front panel Rear panel (2) Left panel Match holder and chain Caster frame 28 29 30 31 32 33 34 35 36 1/4-20 x 3 1/2 inch bolt (4) Bottom connector (3) Tool holder (4) Caster (2) Bottom tray Catch pan holder Catch pan Drip pan (2) Left front door 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Right front door Accessory rack Warm-up basket Steam-N-Chips smoker Hair pin cotter (2) Clevis pin (2) Regulator mounting bracket Corrugated gas line Hose adapter Top left frame Top right frame Back panel Nylon washer (8) 1/4-20 x 1/2 inch bolt (4) 1/4-20 wing nut Wheel hubcap (2) Wheel (2) Cylinder glide (2) Glide axle 56 57 Glide hubcap (2) Cylinder panel FOR THE SUMMIT 58 59 60 Right panel Tank scale assembly 1/4-20 x 1 3/4 inch bolt 61 62 63 1/4-20 keps nut Hose / regulator LP tank 64 65 Filler adapter Wheel frame 450 LP All items are single quantities unless otherwise specified. Parts can be ordered directly from Weber-Stephen Products Company by phone or mail. Note - Do not return parts to Weber-Stephen Products Co. without first contacting the Customer Service Center by phone or mail. Returning the part may not be necessary. While we give much attention to our products, unfortunately an occasional error may occur. If a part is missing, do not go back to the store. Call the Weber Customer Service Center toll free 1-888-33-SUMMIT (1-888-337-8664) to receive immediate assistance. Have your owner's manual and serial number of the barbecue available for reference. Weber-Stephen Products Company Customer Service Center 250 South Hicks Road Palatine, IL 60067-6241 (888) 33-SUMMIT (888-337-8664) WARNING: Use only Weber factory authorized parts.The use of any part that is not factory authorized can be dangerous. This will also void your warranty. 19 PATENTS & TRADEMARKS © 1997 Weber-Stephen Products Co. Weber, the _[ silhouette, Flavorizer and Crossover are registered U.S. trademarks; Summit, Grill Cozy, Gas Catcher, Spider Stopper, and Steam-N-Chips, are trademarks, all of Weber-Stephen Products Co., 200 East Daniels Road, Palatine, IL 60067-6266. U.S.A. Summit Series Gas Barbecues are covered by U.S. Patent Nos. 4,677,964; 4,727,853; 4,777,927; 4,829,978; 4,860,724; 4,941,817; and 4,966,125; and, Canada patent Nos. 1,283,586 and 1,300,995. Printed in the U.S.A.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 20 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Wed Aug 15 06:43:11 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools