Weber Genesis 1000 Series Natural Gas Barbecue Users Manual NG Owners Guide 98613 10/97 PDF File

1000 Series to the manual ec7c3c65-a57d-470f-a304-f1c8a8aa4964

2015-01-05

: Weber Weber-Genesis-1000-Series-Natural-Gas-Barbecue-Users-Manual-162246 weber-genesis-1000-series-natural-gas-barbecue-users-manual-162246 weber pdf

Open the PDF directly: View PDF .
Page Count: 32

Download
Open PDF In Browser	View PDF

Serial Number

Please use this number in registering your warranty and
any correspondence with the factory.

GENESIS 1000 Series
®

Natural Gas Barbecue

Owner’s Manual

WEB

WEB
E
R

WARNING: Follow all leak check procedures
carefully in this manual prior to barbecue
operation. Do this even if barbecue was
dealer assembled.
NOTICE TO INSTALLER: These instructions
must be left with the owner and the owner
should keep them for future use.
FOR YOUR SAFETY
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.

WARNING: Do not try to light this appliance
without reading "Lighting" instructions
section of this manual.
THIS GAS APPLIANCE IS DESIGNED FOR
OUTDOOR USE ONLY.
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. Open lid.
4. If odor continues, immediately call your
gas supplier or your fire department.
98613

10/97

DANGER

Failure to follow the Dangers, Warnings and Cautions contained in this Owner’s Manual
may result in serious bodily injury or death, or in a fire or an explosion causing damage
to property.

WARNINGS
 Do not store a spare or disconnected LP tank under or near this barbecue.
 Improper assembly may be dangerous. Please carefully follow the assembly instructions in this manual.
 After a period of storage, and/or nonuse, the Weber Gas Barbecue should be checked for gas leaks

and burner obstructions before using. See instructions in this manual for correct procedures.
 Do not operate the Weber Gas Barbecue if there is a gas leak present.
 Do not use a flame to check for gas leaks.
 Combustible materials should never be within 24 inches of the top, bottom, back or sides of your

Weber Gas Barbecue.
 Do not put a barbecue cover or anything flammable on or in the storage area under the barbecue.
 Your Weber Gas Barbecue should never be used by children.
 You should exercise reasonable care when operating your Weber Gas Barbecue. It will be hot during

cooking or cleaning, and should never be left unattended.
 Should the burners go out during operation, turn all gas valves off. Open the lid and wait five minutes

before attempting to relight, using the lighting instructions.
 Do not use charcoal or lava rock in your Weber Gas Barbecue.
 Never lean over open grill or place hands or fingers on the front edge of the cooking box.
 Should a grease fire occur, turn off all burners and leave lid closed until fire is out.
 Do not enlarge valve orifices or burner ports when cleaning the valves or burners.
 The Weber Gas Barbecue should be thoroughly cleaned on a regular basis.
 LP gas is not natural gas. The conversion or attempted use of natural gas in an LP unit or LP gas in a

natural gas unit is dangerous and will void your warranty.
 Do not attempt to disconnect any gas fitting while your barbecue is in operation.
 Use heat-resistant barbecue mitts or gloves when operating barbecue.

LP GAS UNITS ONLY:
 Use the regulator that is supplied with your Weber Gas Barbecue.
 Do not attempt to disconnect the gas regulator or any gas fitting while your barbecue is in operation.
 A dented or rusty LP tank may be hazardous and should be checked by your liquid propane supplier.

Do not use an LP tank with a damaged valve.
 Although your LP tank may appear to be empty, gas may still be present, and the tank should be

transported and stored accordingly.
 If you see, smell or hear the hiss of escaping gas from the LP tank:

1. Get away from LP tank.
2. Do not attempt to correct the problem yourself.
3. Call your fire department.

WARRANTY
Weber-Stephen Products Co. (Weber) hereby
warrants to the ORIGINAL PURCHASER of this
Weber Gas Barbecue that it will be free of
defects in material and workmanship from the
date of purchase as follows:

There are no other express warrants except as
set forth herein and any applicable implied
warranties of merchantability and fitness are
limited in duration to the period of coverage of
this express written Limited Warranty. Some
states do not allow limitation on how long an
implied warranty lasts, so this limitation may not
apply to you.

Aluminum Castings, 10 years,
Cooking Grates and Flavorizer Bars, 3 years,
All Remaining Parts, 5 years,

Weber is not liable for any special, indirect or
consequential damages. Some states do not
allow the exclusion or limitation of incidental or
consequential damages, so this limitation or
exclusion may not apply to you.

when assembled and operated in accordance
with the printed instructions accompanying it.
Weber may require reasonable proof of your
date of purchase. THEREFORE, YOU SHOULD
RETAIN YOUR SALES SLIP OR INVOICE.

Weber does not authorize any person or
company to assume for it any other obligation or
liability in connection with the sale, installation,
use, removal, return, or replacement of its
equipment; and no such representations are
binding on Weber.

This Limited Warranty shall be limited to the
repair or replacement of parts which prove
defective under normal use and service and
which on examination shall indicate, to Weber's
satisfaction, they are defective. Before returning
any parts, contact Weber-Stephen Products Co.
Customer Service Center. If Weber confirms the
defect and approves the claim, Weber will elect
to replace such parts without charge. If you are
required to return defective parts, transportation
charges must be prepaid. Weber will return parts
to the purchaser, freight or postage prepaid.

This Warranty applies only to products sold at
retail.
WEBER-STEPHEN PRODUCTS CO.
Customer Service Center
250 South Hicks Road
Palatine, IL 60067-6241
(800) 446-1071

This Limited Warranty does not cover any failures
or operating difficulties due to accident, abuse,
misuse, alteration, misapplication, vandalism,
improper installation or improper maintenance or
service, or failure to perform normal and routine
maintenance, including but not limited to damage
caused by insects within the burner tubes, as set
out in this owner's manual.
Deterioration or damage due to severe weather
conditions such as hail, hurricanes, earthquakes
or tornadoes, discoloration due to exposure to
chemicals either directly or in the atmosphere, is
not covered by this Limited Warranty.

PATENTS AND TRADEMARKS
© 1997 Weber. Weber, , Genesis, Flavorizer and Crossover are
registered U.S. trademarks; Perma-Mount, Gas Catcher,
FlameCheck, Steam-N-Chips, Spider Stopper, and Warm-Up are
U.S. trademarks of Weber-Stephen Products Co., 200 East Daniels
Road, Palatine, IL 60067-6266. U.S.A. Genesis Gas Barbecues
are covered under the following patent nos.: U.S.A. #4,677,964;
4,727,853; #4,777,927; #4,829,978; #4,860,724; #4,941,817;
#4,966,125; #5,070,776; #D293,067; #D316,355; Canada: Rd
1987 Reg. #58,034; #1,279,540; #1,283,586; #1,300,994;
#1,300,995. Printed in the U.S.A.

Contents
WARNINGS ................................................................ 2
Warranty & Patents.................................................. 3-4
General Instructions.................................................... 6
Assembly ............................................................... 7-21
Operating Instructions
Lighting........................................................ 22-23
Cooking ............................................................ 24
Storage and/or Nonuse .................................... 24
Cleaning .......................................................... 24
Troubleshooting & Maintenance
Annual Maintenance......................................... 25
General Maintenance.................................. 26-28
Troubleshooting................................................ 29
Parts Listing .............................................................. 31
b
c
e

f
g

FEATURES:
a) Convenient tables and racks.

e) Weber Warm-Up Basket for additional cooking or
warming space.

b) Heavy gauge porcelain-on-steel lid seals in heat.
c) Rapid read thermometer for precision cooking
measures grill temperature, and can be removed and
inserted into the food.

Separate burners for temperature control.

d) Heavy gauge steel Flavorizer Bars distribute heat
within the grill. Flavorizer Bars heat just the right
amount of drippings for flavoring, letting excess fat
drip past to help prevent flare-ups.

h) Catch pan catches excess grease.

g) Crossover Ignition System with Gas Catcher Ignition
Chamber.
i)
5

Locking casters for additional portability.

General Instructions
Storage

Your Weber Gas Barbecue is a portable outdoor cooking
appliance. With the Weber Gas Barbecue you can grill,
barbecue, roast and bake with results that are difficult to
duplicate with indoor kitchen appliances. The closed lid and
Flavorizer Bars produce that "outdoor" flavor in the food.
The Weber Gas Barbecue is portable so you can easily
change its location in your yard or on your patio. Portability
means you can take your Weber Gas Barbecue with you if
you move.

Not for use by children.

■

If there are local codes that apply to portable gas
grills, you will have to conform to them. If there are no
local codes, you must conform to the latest edition of
the National Fuel Gas Code: ANSI Z 223.1.

■

This Weber Gas Barbecue is designed for natural
(piped in city) gas only. Do not use Liquid Propane
(LP) bottled gas.The valves, orifices and hose are for
natural gas only.

■

Do not use with charcoal fuel.

■

Check that the area under the control panel and the
bottom tray are free from debris that might obstruct
the flow of combustion or ventilation air.

■

When the Weber Gas Barbecue is stored indoors, the
gas supply must be disconnected.

WARNING: Only use this barbecue outdoors in a
well ventilated area. Do not use in a garage, building,
breezeway or any other enclosed area.

These instructions will give you the minimum
requirements for assembling your Weber Gas
Barbecue. Please read the instructions carefully
before using your Weber Gas Barbecue. Improper
assembly can be dangerous.

■

The gas must be turned OFF at the natural gas supply
when the Weber Gas Barbecue is not in use.

Operating area

The natural gas supply is easy to use and gives you more
cooking control than charcoal fuel.
■

■

Never use your Weber Gas Barbecue under an
unprotected combustible roof or overhang.

■

Your Weber Gas Barbecue is not intended to be
installed in or on recreational vehicles and/or boats.

■

Do not use combustible materials within 24 inches of
the top, bottom, back or sides of the grill.

■

The entire cooking box gets hot when in use. Do not
leave unattended.

■

Keep any electrical supply cord and the fuel supply
hose away from any heated surface.

■

Keep the cooking area clear of flammable vapors and
liquids, such as gasoline, alcohol, etc., and
combustible materials.

Gas supply testing
■

Disconnect your Weber Gas Barbecue when the gas
supply is being tested at high pressures. This appliance
and its individual shutoff valve must be disconnected
from the gas supply piping system during any pressure
testing of that system at test pressures in excess of
1/2 psig (3.5 kPa).

■

Turn off your Weber Gas Barbecue when the gas
supply is being tested at low pressures. This appliance
must be isolated from the gas supply piping system by
closing its individual manual shutoff valve during any
pressure testing of the gas supply piping system at
the pressure equal to or less than 1/2 psig (3.5 kPa).

For Installation in Canada
These instructions, while generally acceptable, do not
necessarily comply with the Canadian Installation codes,
particularly with piping above and below ground. In
Canada the installation of this appliance must comply with
local codes and/or Standard CAN/CGA-B149.1 (Installation
Code for Natural Gas Burning Appliances and Equipment).

Step 1

Assembly

Check package contents

Tools needed
Screwdriver

Cooking box
(assembly)

Phillips screwdriver

Hammer

7/16 inch or an adjustable wrench
Lid
(assembly)
®
®

Pliers

Block of wood
Hose

Supplies needed
You will need a soap and water solution to check for gas
leaks. (See Step "Check for gas leaks.")
Bottom tray

Note - The hardware size of nuts, bolts and screws is given.
For example "1/4-20 x 2 inch bolt" means a bolt 1/4 inch in
diameter with 20 threads to the inch, 2 inches long. On a
small screw for example, "6-32 x 1/2 inch screw" means a
number 6 screw, with 32 threads to the inch, 1/2 inch long.
While we give much attention to our products,
unfortunately an occasional error may occur. If a part is
missing, do not go back to the store. Call the Weber
Customer Service Center toll free 1-800-446-1071 to
receive immediate assistance. Have your owner ’s
manual and serial number of the barbecue available
for reference.

Two cooking grates

Control panel

Left frame

Five long Flavorizer Bars

Eight short Flavorizer Bars
Right frame

Front panel
Wheel frame

Catch pan holder
Caster frame

Catch pan
Two frame connectors

Two drip pans
Work table

Manifold bracket
Swing table assembly

Thermometer

WE BE

WE B E R

Support rod
R

Two wheels
Axle

Two casters
Accessory rack

Warming rack

Warm-Up Basket

Check contents of hardware packs
Two plastic buttons
(actual size)

Three burner control knobs

1/4-20 keps nut
Three tool holders

Eleven 1/4 inch nylon washers
Five tubing plugs
(two are spares)
Two hair pin cotters

Support rod holder
Two wheel hubcaps

Two Phillips screws/washers

Swing table end bracket

Two hinge pins
(hardware size: 1/4 x 1 1/2 inch clevis pin)
(actual size)

Five 1/4-20 x 2 inch bolts
(actual size)

Six 1/4-20 x 1/2 inch bolts
(actual size)

Step 3

Assemble wheels

Assemble top frame

You will need: axle, two wheel hubcaps, two wheels,
wheel frame, hammer and a block of wood.

You will need: left frame, right frame, two 1/4-20 x 1/2 inch
bolts, two nylon washers and a 7/16 inch wrench.

Place one end of the axle on the block of wood (or other
protected surface). Tap on one hubcap.

Note - Work on carpeted area (on grass or one of the
boxes) to protect the finish during frame assembly.

Put one wheel on the axle, WEBER side toward the
hubcap. Slide the axle through the frame. Add the other
wheel, WEBER side out. Tap on the hubcap. Figure 1.

Lay the leg pieces as shown so the leg tabs point up.
Figure 2.
Slip the two frame pieces together with the tabs inside.
Figure 2 (a). Slip washers on bolts, insert bolts as shown
and tighten. Figure 2 (b). (If you try to insert a bolt and
there are no holes, you have the left frame turned the
wrong way. Turn the left frame around.)

WE BE

WE B E R

Step 2

Frame tabs

(a)

Figure 1
Leg tabs
Right frame

Left frame

(b)

Figure 2

Step 4

Step 5

Continue frame assembly

Complete frame assembly

You will need: caster frame, wheel frame, four 1/4-20 x 1/2
inch bolts, four nylon washers and a 7/16 inch wrench.

You will need: partial frame assembly, two frame connectors,
four 1/4-20 x 2 inch bolts, four nylon washers and a 7/16
inch wrench.

Place the caster frame onto the tabs of the left frame with
the dimple to the inside. Figure 3. Place the wheel frame
onto the tabs of the right frame with the dimple to the
inside. Figure 3.

Hold one frame connector between the caster and wheel
frame. Add the nylon washer to the bolt. Put the bolt
through the frame and screw into frame connector.
Tighten.

The leg tabs must be on the inside of the frames.

Repeat procedure with the other frame connector. Figure 4.

Add the washers to the bolts, insert in the holes as shown
and tighten with the wrench. Figure 3.
Dimples to
the inside

Figure 4

Figure 3

Step 6

Step 7

Insert casters

Add front panel

You will need: frame assembly and two casters.

You will need: front panel and two plastic buttons.

Push the casters firmly into the inserts in the ends of the
caster legs. Figure 5.

Turn frame assembly right side up.
Align the panel with the holes in the frame and insert the
plastic buttons through the front panel and frame. Figure 6.
Plastic buttons

View from rear
of barbecue

Figure 5

Figure 6

Step 8

Your Weber Gas Barbecue burner assembly has been
factory assembled, pressure and flame tested. As a safety
precaution we recommend you check the burner alignment:

Add cooking box
You will need: frame assembly, cooking box assembly,
1/4-20 x 2 inch bolt, nylon washer, 1/4-20 keps nut, pliers
and a 7/16 inch wrench.

a) Do the valves fit into the ends of the burners?
Figure 9 (a).
b) Are the ends of the burners under the washers at the
left rear and left front of the cooking box? The screws
are only guides. Do not tighten. Figure 9 (b).

Set the cooking box in the frame so the burner tubes are
under the frame brace. Figure 7.

c) Are the wing nuts under the burner assembly hand
tight? Do not tighten with pliers. Figure 9 (c).

Burner tubes

If you answered YES to a, b and c, the burners are
correctly aligned. If you answered NO, the burners are
misaligned. Contact Weber-Stephen Customer Service.
Do not use barbecue.

Frame brace

Guide screw

Figure 7

(b)

Slide the cooking box to the left within the frame. Put washer
on bolt. Insert the bolt through the cooking box and frame
with the head of the bolt outside the box. Figure 8. Add the
keps nut. Tighten by holding the bolt with pliers while you
tighten the nut with the 7/16 inch wrench.

(a)

View from
behind
cooking
box
(c)

Figure 9

Figure 8

Wing nuts

Step 9

Step 10

Install manifold bracket

Install igniter

You will need: manifold bracket

Note - The igniter wires are already attached to the Gas
Catcher Ignition Chamber and the igniter. This was done to
factory test the ignition system.

Hook the bracket onto the manifold at the center burner
valve. Place your hand underneath the bracket. Lift the
manifold, bracket and cooking box slightly and hook the
tab of the bracket onto the frame brace. Figure 10.
Frame brace

The igniter lock nut is on the igniter.
Insert the top of the igniter up through the large part of
the keyhole in the frame brace. Figure 11 (b). Loosen the
igniter lock nut and slide the igniter into the small part of
the keyhole. Figure 11 (c). Tighten the igniter lock nut.
Figure 11.

Manifold bracket

Note - If the igniter works loose, carefully tighten the igniter
lock nut with an adjustable wrench or pliers.
(a)

Figure 10

Frame brace
(b)

Figure 11
Keyhole in
frame brace

Igniter lock nut
(c)

Frame brace
Small part of keyhole
in frame brace

Step 11

Typical natural gas supply installation. Figure 12.
Gas supply

Install gas supply

Inside wall

General Specifications for Piping
Note - Contact your local municipality for building
codes regulating outdoor gas barbecue installations.
In absence of Local Codes, you must conform to the
latest edition of ANSI Z223.1. WE RECOMMEND THAT
THIS INSTALLATION BE DONE BY A PROFESSIONAL.

Outside wall
Shut off
To barbecue

Some of the following are general requirements taken
from ANSI Z223.1, for gas supply installations. Refer to
ANSI Z223.1 latest edition for complete specifications.
■

This barbecue is designed to operate at 7 inches of
water column pressure (.2526 psi).

■

A manual shut-off valve must be installed outdoors,
immediately ahead of the quick disconnect.

■

An additional manual shut-off valve indoors should be
installed in the branch fuel line in an accessible
location near the supply line.

■

Locking
shut off

Quick Disconnect
Male fitting

The quick disconnect is
installed above ground

Figure 12

Gas line piping

The quick disconnect connects to a 3/8 inch NPT
thread from the gas source. The quick disconnect
fitting is a hand-operated device that automatically
shuts OFF the flow of gas from the source when the
barbecue is disconnected.

■

If the length of line required does not exceed 50 feet,
use a 5/8" O.D. tube. One size larger should be used
for lengths greater than 50 feet.

■

The quick disconnect fitting can be installed
horizontally, or pointing downward. Installing the fitting
with the open end pointing upward can result in
collecting water and debris.

Gas piping may be copper tubing, type K or L;
polyethylene plastic tube, with a minimum wall
thickness of .062 inch; or standard weight (schedule
40) steel or wrought iron pipe.

■

The dust covers (supplied plastic plugs) help keep the
open ends of the quick disconnect fitting clean while
disconnected.

Copper tubing must be tin-lined if the gas contains
more than 0.3 grams of hydrogen sulfide per 100
cubic feet of gas.

■

Pipe compound should be used which is resistant to
the action of natural gas when connections are made.

Plastic tubing is suitable only for outdoor, underground
use.

■

Gas piping in contact with earth, or any other material
which may corrode the piping, must be protected
against corrosion in an approved manner.

■

Underground piping must have a minimum of
18" cover.

■

The outdoor connector must be firmly attached to
rigid, permanent construction.

WARNING: Do not route the 12 foot hose under a
deck. The hose must be visible.

Test connections
All connections and joints must be thoroughly tested for
leaks in accordance with local codes and all listed
procedures in the latest edition of ANSI Z223.1.

 DANGER
Do not use an open flame to check for
gas leaks. Be sure there are no sparks or
open flames in the area while you check
for gas leaks. This will result in a fire or
explosion which can cause serious
bodily injury or death, and damage
to property.
15

Step 12

Step 13

Check that all burner valves are off

Connect flexible hose to manifold

You will need: one burner control knob.

You will need: the 12 foot natural gas supply hose and a
3/4 inch wrench.

Valves are shipped in the OFF position, but you should
check to be sure. Put the knob on each valve. Check by
pushing down and turning clockwise. If they do not turn
they are off, proceed to the next step.Figure 13.

Thread fitting end of hose onto manifold. Figure 14 (a).
Tighten with wrench.
(a)

Figure 13

Figure 14

Step 14

Check:

Check for gas leaks

a) Hose to manifold connection. Figure 16 (a).
WARNING: If there is a leak at connection (a),
retighten the fitting with a wrench and recheck for
leaks with soap and water solution.

 DANGER
Do not use an open flame to check for gas
leaks. Be sure there are no sparks or open
flames in the area while you check for
leaks. This will result in a fire or explosion
which can cause serious bodily injury or
death and damage to property.

If a leak persists after retightening the fitting, turn OFF
the gas. DO NOT OPERATE THE BARBECUE. Contact
Weber-Stephen Customer Service.
b) Valves to manifold connections. Figure 16 (b).
c) Hose to quick disconnect connection. Figure 16 (c).

WARNING: You should check for gas leaks every
time you disconnect and reconnect a gas fitting.

WARNING: If there is a leak at connections (b) or (c),
turn OFF the gas. DO NOT OPERATE THE BARBECUE.
Contact Weber-Stephen Customer Service.

Note - All factory made connections have been thoroughly
checked for gas leaks. The burners have been flame
tested. As a safety precaution you should recheck all
fittings for leaks before using your Weber Gas Barbecue.
Shipping and handling may have loosened or damaged a
gas fitting.

When leak checks are complete, turn gas supply OFF at
the source and rinse connections with water.

(a)

WARNING: Perform these leak checks even if your
barbecue was dealer or store assembled.
You will need: a soap and water solution and a rag or
brush to apply it.
To perform leak checks: Slide back the collar of the quick
disconnect. Push male fitting of the hose into the quick
disconnect, and maintain pressure. Figure 15 (a). Slide
the collar closed. Figure 15 (b). If it does not engage or
lock, repeat procedure. Gas will not flow unless the quick
disconnect is properly engaged.

(b)

Locking shut off
To barbecue

Outside house wall

(a)

(c)

Figure 16
Male fitting
(b)

Collar

Quick disconnect
engaged

Figure 15
Turn on gas supply.
Check for leaks by wetting the connections with the soap
and water solution and watching for bubbles. If bubbles
form or if a bubble grows there is a leak.

Note - Since some leak test solutions, including soap and
water, may be slightly corrosive, all connections should be
rinsed with water after checking for leaks.
WARNING: Do not ignite burners when leak checking.
17

Step 15
Install Flavorizer Bars and Cooking Grates

Step 16
Install the bottom tray

You will need: five long Flavorizer Bars, eight short
Flavorizer Bars and two cooking grates.

You will need: bottom tray, catch pan holder, catch pan and
one drip pan.

Set the long Flavorizer Bars side to side in the lower
position, then set the short Flavorizer Bars front to back in
the upper position in the cooking box. Figure 17.

Finger grip on front
edge of bottom tray

Front side of catch
pan holder

Figure 19
Hook the ends of the catch pan holder into the hole in the
bottom tray. Figure 20. The front of the catch pan holder
must be on the same side as the finger grip of the
bottom tray.

Figure 17
Finger grip

The open "U" of the cooking grates goes down. Set the
cooking grates onto the ledges in the cooking box. Figure 18.

Figure 20

Slide the bottom tray onto the mounting rails under the
cooking box with finger grip toward you. Figure 21.
CAUTION: Do not line bottom tray with aluminum foil.
It can cause grease fires by trapping the grease and not
allowing grease to flow into the catch pan.

Figure 18

Bottom tray

Figure 21
Put the foil drip pan into the catch pan.
Slide the catch pan into the catch pan holder with its finger
grip towards you.

Step 17

Step 18

Install Lid
You will need: lid, two hinge pins and two hair pin cotters.

Add tool holders, control panel and burner
control knobs

Set the lid in place. Align the hinges at the rear of the
barbecue. Insert hinge pins from the outside. Insert hair pin
cotters into the small holes in the hinge pins. Figure 22.

You will need: three tool holders, control panel, two
Phillips screws/washers, a Phillips screwdriver, and three
burner control knobs.
Hook the tool holders over the frame rail. Figure 23.
Set the control panel in place over both frame braces.
(Hold the Crossover Ignition button up while setting the
control panel in place.) Line up the holes in the control
panel with the holes in the frame brace. Insert screws and
tighten with a Phillips screwdriver until snug. Do not
overtighten. Figure 23 (a).

Hair pin cotter

Hinge pin

Push on the burner control knobs. Figure 23 (b).
Insert in
frame brace
(a)
Crossover
Ignition
Button

Figure 22

Control panel
Phillips screws/
washers
(b)

Tool holders

Figure 23

Step 19

Insert one end of the hinge rod into the hole in the frame.
Figure 25 (a).

Install swing table

Insert the other end into the hole in the swing table end
bracket. Figure 25 (b). Hold the end bracket at an angle so
the lower tab is inside the frame tube. Push the bracket into
the frame. Check to see that the lower tab of the bracket is
hooked in the slot in the frame. Figure 25 (c).

You will need: swing table assembly, support rod, support
rod holder and swing table end bracket.
Allow the slide bar to hang down. Push the support rod
into the lower support bracket. Figure 24 (a). Swing the
rod up so you can slide the rod all the way inside the
locking tab. Figure 24 (b). The rod should swing freely
inside the locking tab. Figure 24 (c).

To fully seat the bracket, you may have to tap it lightly with a
hammer.
WARNING: If swing table end bracket is in any way
cracked or damaged, do not use swing table. Call our
Customer Service Center to order a new part.
Install support rod holder on leg. Figure 25 (d). Hook the
support rod into the support rod holder.
WARNING: The load limit for the swing table is
30 pounds.
Hinge rod

(b)

(a)

(c)

(b)
Support rod
(a)

Figure 24
View from rear
of barbecue

Slot in frame
(view from below)
(c)

(d)

Figure 25

Step 20
Complete accessory installation
You will need: Warm-Up Basket, warming rack, work
table, accessory rack, three tubing plugs, thermometer
and a hammer.
Insert one end of the Weber Warm-Up Basket into the hole
in the right end of the lid and the other end into the slot in
the left end of the lid. Figure 26 (a).
Set the warming rack into the slots at the rear of the
cooking box. Figure 26 (b).
Set the work table onto the left side rails. Figure 26 (c).
Set the accessory rack in place between the two frame
connectors. Figure 26 (d).
Insert the thermometer into its holder. Figure 26 (e).
Insert the tubing plugs into the ends of the frame. To fully
seat the plugs, you may have to tap them lightly with a
hammer. Figure 26 (f).

(a)

(b)

(e)

(c)

(f)

(d)

Figure 26
CAUTION: To keep the barbecue stationary, the tabs
on the locking casters should be in the down position.

OPERATING INSTRUCTIONS
Lighting

1) Open the lid. Figure 1.

Summary lighting instructions are on the control panel.

2) Make sure all burner control knobs are turned OFF.
(Push each burner control knob down and turn
clockwise.)

 DANGER

3) Turn gas supply valve on.

Failure to open lid while igniting the
barbecue, or not waiting 5 minutes to
allow the gas to clear if the barbecue
does not light, may result in an explosive
flame-up which can cause serious bodily
injury or death.

WARNING: Do not lean over open barbecue. Keep
your face and body at least one foot away from the
matchlight hole when lighting the barbecue.
4) Push Front burner control knob down and turn to
START/ HI.
5) Push the Crossover Ignition Button several times,
so it clicks each time.

Crossover Ignition System

6) Check that the burner is lit by looking through the
matchlight hole on the front of the cooking box.

Note - The Crossover Ignition System ignites the Front
burner with a spark from the igniter electrode inside the Gas
Catcher Ignition Chamber. You generate the energy for the
spark by pushing the Crossover Ignition Button until it clicks.

WARNING: If the burner does not light, turn the
Front burner control knob to OFF and wait 5 minutes
to let the gas clear before you try again or try to light
with a match.

WARNING: Check hose before each use of barbecue
for nicks, cracking, abrasions or cuts. If the hose is
found to be damaged in any way, do not use the
barbecue. Replace using only Weber authorized
replacement hose. Order from Weber-Stephen Products
Co., Customer Service Center or authorized dealer.

7) After the FRONT burner is lit you can turn on the other
burners.

Note - Always light the FRONT burner first. The other
burners ignite from the FRONT burner.

Crossover Ignition System

To Extinguish

Turn gas supply OFF at the source, then push down
and turn each burner control knob clockwise to OFF.
2

7
5

6
4
Figure 1

Manual Lighting
WARNING: If the burner does not light, turn the Front
burner control knob to OFF and wait 5 minutes to let
the gas clear before you try again or try to light with a
match.

 DANGER
Failure to open lid while igniting the
barbecue, or not waiting 5 minutes to
allow the gas to clear if the barbecue
does not light, may result in an explosive
flame-up which can cause serious bodily
injury or death.

7) After the FRONT burner is lit you can turn on the other
burners.

Note - Always light the FRONT burner first. The other
burners ignite from the FRONT burner.

To Extinguish

1) Open the lid. Figure 2.

Turn gas supply OFF at the source, then push down
and turn each burner control knob clockwise to OFF.

2) Make sure all burner control knobs are turned OFF.
(Push each burner control knob down and turn
clockwise.)
3) Turn gas supply valve on.
4) Strike a match and put the flame into the matchlight
hole in the front of the cooking box.
Manual Lighting

7
3

6
5
Figure 2

WARNING: Do not lean over open barbecue. Keep
your face and body at least one foot away from the
matchlight hole when lighting the barbecue.
5) Push Front burner control knob down and turn to
START/ HI.
6) Check that the burner is lit by looking through the
matchlight hole on the front of the cooking box.

Cooking

Storage and/or Nonuse

WARNING: Do not move the Weber Gas Barbecue
when operating or hot.

■

When storing the Weber Gas Barbecue, make sure
that the inside shut off valve and/or locking outdoor
shut off valve is secured in the OFF position. When
the Weber Gas Barbecue is stored indoors, the gas
supply MUST BE DISCONNECTED.

■

After a period of storage and/or nonuse the Weber
Gas Grill should be checked for gas leaks and any
obstructions in the burner tubes before using. (See
Sections General and Annual Maintenance.)

■

Check that the areas under the control panel and the
bottom tray are free from debris that might obstruct
the flow of combustion or ventilation air.

■

The Spider Stopper Guards should also be checked for
any obstructions. (See Section "Annual Maintenance.")

You can adjust the FRONT, CENTER and BACK burners as
desired. The control settings High (H), Medium (M), Low
(L), or Off (O) are described in your Weber cookbook. The
cookbook uses these notations to describe the settings of
the FRONT, CENTER, and BACK burners. For example, to
sear steaks you would use (HHH) (all burners at high).
Then to complete cooking you would use (MOM) (FRONT
at medium, CENTER off, and BACK at medium). See your
Weber cookbook for detailed cooking instructions.

Note: The temperatures inside your cooking box, for the
first few uses, while surfaces are still very reflective, may
be hotter than those shown in your cookbook. Cooking
conditions may require the adjustment of the burner
controls to attain the correct cooking temperatures.
CAUTION: Replace thermometer in lid when not in
use. Do not leave thermometer in food while cooking.

Periodic Cleaning

If burners go out during cooking, open lid, turn off all
burners and wait 5 minutes before relighting.

WARNING: Turn your Weber Gas Barbecue OFF and
wait for it to cool before cleaning.

Preheating

CAUTION: Do not clean your Flavorizer Bars or
cooking grates in a self-cleaning oven. Replacement
cooking grates and Flavorizer Bars are available
through your retailer or the Weber-Stephen Customer
Service Center.

Your Weber Gas Barbecue is an energy efficient
appliance. It operates at a low B.T.U. rate for economy. To
preheat, after lighting, close lid and turn all burners to high
(HHH). Preheating to between 500° and 550° F (260° and
290° C) will take 10 to 15 minutes depending on
conditions such as air temperature and wind.

Outside surfaces - Use a warm soapy water solution.
CAUTION: Do not use oven cleaner, abrasive
cleansers (kitchen cleansers) cleaners that contain
citrus products or abrasive cleaning pads on barbecue
or cart surfaces.

Drippings and grease
The Flavorizer Bars are designed to "smoke" the right
amount of drippings for flavorful cooking. Excess drippings
and grease accumulate in the catch pan under the bottom
tray. Disposable foil liners are available that fit the catch pan.

Bottom tray - Remove excess grease and then wash with
warm soapy water.

WARNING: Check the bottom tray for grease buildup before each use. Remove excess grease to avoid a
grease fire in the bottom tray.

Flavorizer Bars and Cooking Grates- Clean with a
suitable brass bristle brush. As needed, remove from grill
and wash with warm soapy water.
Catch pan - Disposable foil trays are available, or you can
line the catch pan with aluminum foil. To clean the catch
pan, wash with warm soapy water.
Thermometer - Wipe with warm soapy water, clean with
plastic scrub ball. Do not put in dishwasher or submerge in
water.
Inside cooking box - Brush any debris off of burners tubes.
DO NOT ENLARGE BURNER PORTS (OPENINGS). Wash
inside of cooking box with warm soapy water.
Inside Lid - While lid is warm, wipe inside with paper towel
to prevent flaking due to grease build-up.

Annual Maintenance

Check:
a) Hose to manifold connection. Figure 3 (a).

After a period of nonuse we recommend that you perform
the following maintenance procedures for your safety.

WARNING: If there is a leak at connection (a),
retighten the fitting with a wrench and recheck for
leaks with soap and water solution.

■

If a leak persists after retightening the fitting, turn OFF
the gas. DO NOT OPERATE THE BARBECUE. Contact
Weber-Stephen Customer Service.
b) Valves to manifold connections. Figure 3 (b).

Inspect the burners for correct flame pattern. Clean if
necessary, following the procedures outlined in the
"General Maintenance" section of this manual.

c) Hose to quick disconnect connection. Figure 3 (c).
WARNING: If there is a leak at connections (b) or (c),
turn OFF the gas. DO NOT OPERATE THE BARBECUE.
Contact Weber-Stephen Customer Service.

Check all gas fittings for leaks.

When leak checks are complete, turn gas supply OFF at
the source and rinse connections with water.

(a)
(b)

WARNING: You should check for gas leaks every
time you disconnect and reconnect a gas fitting.
You will need: a soap and water solution and a rag or
brush to apply it.

(c)

To perform leak checks: Make sure all burners are in the
OFF position. Turn on gas supply.
WARNING: Do not ignite burners while leak checking.
Check for leaks by wetting the connections with the soap
and water solution and watching for bubbles. If bubbles
form or if a bubble grows there is a leak.

Figure 3

Note - Since some leak test solutions, including soap and
water, may be slightly corrosive, all connections should be
rinsed with water after checking for leaks.

Inspection and Cleaning of the Weber Spider
Stopper Guards
To inspect the Spider Stopper Guards, remove the control
panel and look to see if they have dust or dirt on their
outside surfaces. If they are dirty, brush off the outside
surface of the Spider Stopper Guards with a soft bristle
brush (an old toothbrush for example). Check that there
are no gaps in the Spider Stopper Guards’ seams or in the
fit around the burners or valves. (See Section "General
Maintenance".)

General Maintenance

Main Burner Flame Pattern

Weber Spider Stopper Guards

The Weber Gas Barbecue burners have been factory set
for the correct air and gas mixture. The correct flame
pattern is shown in Figure 6.

Your Weber Gas Barbecue, as well as any outdoor gas
appliance, is a target for spiders and other insects. They
can nest in the venturi section of the burner tubes. This
blocks the normal gas flow, and can cause the gas to flow
back out of the air shutter. Figure 4. This could result in a
fire in and around the air shutters, under the control panel,
causing serious damage to your barbecue.

Tips occasionally yellowish
Burner inside
cooking box

Light blue

Venturi

Flames

If the flames do not appear to be uniform the length of the
burner tube, follow the burner cleaning procedures.

Venturi fin

Air shutter

Dark blue

Figure 6

Figure 4

Main Burner Cleaning Procedure

The Weber Spider Stopper Guard is factory installed. It fits
tightly around the air shutter section of the burner tube and
the valve, thereby preventing spiders and other insects
access to the burner tubes through the air shutter openings.
Figure 5.

Turn off the gas supply. Remove the manifold. (See
Section “Replacing the main burners”.)
Look inside each burner with a flashlight. Figure 7.

Weber Spider
Stopper Guard

Figure 7
Clean the inside of the burners with a wire (a straightened
out coat hanger will work). Figure 8. Check and clean the
air shutter opening at the ends of the burners. Check and
clean the valve orifices at the base of the valves. Use a
brass bristle brush to clean outside of burners. This is to
make sure all the burner ports are fully open.

Figure 5
We recommend that you inspect the Weber Spider
Stopper Guards at least once a year. (See section
“Annual Maintenance”.) Also inspect and clean the
Spider Stopper Guards if any of the following
symptoms should ever occur.
1. The smell of gas in conjunction with the burner flames
appearing yellow and lazy.
2. Barbecue does not reach temperature.

Figure 8

3. Barbecue heats unevenly.

CAUTION: Do not enlarge the burner ports when
cleaning.

4. One or more of the burners do not ignite.

 DANGER

Replacing Main Burners

Failure to correct these symptoms may
result in a fire which can cause serious
bodily injury or death and cause damage
to property.

a) Your Weber Gas Barbecue must be OFF and cool.
b) Turn gas OFF at source.
c) Remove control panel: take off the burner control
knobs. Remove the screws holding the control panel
in place. Lift off the control panel.

d) Unlatch the Spider Stopper Guards and remove.
Figure 9.

CAUTION: The burner openings must be positioned
properly over the valve orifices. Figure 13a.
Check proper assembly before fastening manifold in
place. Figure 13b.
(a)
Valve

Figure 9

Burner

e) Remove the manifold bracket and unscrew the two
wing nuts that hold the manifold to the cooking box.
Pull the manifold and valve assembly out of the
burners and carefully set it down. Figure 10.

(b)

View from behind
cooking box

Wing nuts

Figure 13

Figure 10
f)

Slide the burner assembly out from under the guide
screw and washer in the corners of the cooking box.
Figure 11.

Reinstall the Spider Stopper Guards. Slightly rotate
the Spider Stopper Guards so that the seams are in
line with the Venturi fins. There should be no gaps in
the seams or in the fit around the burners and valves.
Figure 14.

Guide screw
Check fit
around valve
Venturi fin

Figure 11
Check fit around burner

g) Lift and twist the burner assembly slightly, to separate
the crossover tube from the burners. Figure 12.
Remove the burners from the cooking box.

Figure 14

Crossover tube

Figure 12
h) To reinstall the burners, reverse steps c) through g).
27

CAUTION: If the Spider Stopper Guards do not fit
tightly, contact Weber-Stephen Customer Service.
WARNING: After reinstalling the gas lines, they
should be leak checked with a soap and water
solution before using the barbecue. (See Step“Check
for gas leaks”.)

Crossover Ignition System Operations
If the Crossover Ignition System fails to ignite the Front
burner, light the Front burner with a match. If the Front
burner lights with a match, then check the Crossover
Ignition System.
■

Check that both the white and black ignition wires are
attached properly. Figure 15.

White wire

Black wire

Figure 15
■

Check that the Crossover Ignition button pushes the
igniter (button) down, and returns to the up position.

■

Check to see if the igniter is loose in the frame.
Tighten if necessary; see Step “Install igniter” for
correct procedure.

If the Crossover Ignition System still fails to light, See
Section "Manual Lighting", and contact Weber-Stephen
Customer Service.

TROUBLESHOOTING
Problem

Check

Cure

Burners burn with a yellow or orange
flame, in conjunction with the smell of gas.

Inspect Weber Spider Stopper
Guards for possible obstructions.
(Blockage of holes.)

Clean Weber Spider Stopper
Guards. (See Section "Annual
Maintenance".)

Burner does not light, or flame is low in HIGH
position.

Is fuel hose bent or kinked?

Straighten fuel hose.

Does the Front burner light with a
match?

If you can light the Front
burner with a match, then
check the Crossover Ignition
System.

Are you preheating barbecue in the
prescribed manner?

All burners on high for 10 to
15 minutes for preheating.

Are the cooking grates and
Flavorizer Bars heavily coated with
burned-on grease?

Clean thoroughly. (See
Section "Periodic Cleaning".)

Is the bottom tray "dirty" and not
allowing grease to flow into catch
pan?

Clean bottom tray.

Burner flame pattern is erratic. Flame is low
when burner is on HIGH. Flames do not run the
whole length of the burner tube.

Are burners clean?

Clean burners. (See Section
"General Maintenance".)

Inside of lid appears to be “peeling.”
(Resembles paint peeling.)

The lid is porcelain-on-steel, not
Clean thoroughly. (See
paint. It cannot “peel.” What you are Section "Periodic Cleaning".)
seeing is baked on grease that has
turned to carbon and is flaking off.
THIS IS NOT A DEFECT.

Experiencing flare-ups:

CAUTION: Do not line the bottom tray
with aluminum foil.

If problems cannot be corrected by using these methods, please contact Weber-Stephen Customer Service.

33
2

34
35

3
4
5
6
7
36
37
38
39
40
41
8

42
43
44
45
46
47

9
10
11

12
13-14
15

50
49-53

17
10,14
18

19
20

E BE R

23
24

28 29

30
31

Parts List
While we give much attention to our products,
unfortunately an occasional error may occur. If a part is
missing, do not go back to the store. Call the Weber
Customer Service Center toll free 1-800-446-1071 to
receive immediate assistance. Have your owner’s manual
and serial number of the barbecue available for reference.

All items are single quantities unless otherwise
specified.
Parts can be ordered directly from Weber-Stephen
Products Company by phone or mail.

Note - Do not return parts to Weber-Stephen Products
Co. without first contacting the Customer Service
Center by phone or mail. Returning the part may not be
necessary.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

Weber-Stephen Products Company
Customer Service Center
250 South Hicks Road
Palatine, IL 60067-6241
(800) 446-1071

Lid (assembly)
Lid handle
Warm-Up Basket
Warming rack
Short Flavorizer bars (8)
Long Flavorizer bars (5)
Cooking grates (2)
Work table
Tubing plugs (5)
1/4-20 x 2 inch bolts (5)
Swing table end bracket
Left frame
1/4-20 x 1/2 inch bolts (6)
1/4 inch nylon washers (11)
Caster frame
Swing table assembly
Support rod holder
Support rod
Casters (2)
Bottom tray
Catch pan holder
Catch pan
Drip pans (2)
Accessory rack
Frame connectors (2)
Wheel hubcaps (2)
Wheels (2)
Tool holders (3)
Wheel frame
Front panel
Plastic buttons (2)
Axle

33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56

Hair pin cotters (2)
Hinge pins (2)
Thermometer
1/4-20 keps nut
Cooking box
Burner control knobs (3)
Control panel
Igniter button
Phillips screws/washers (2)
Crossover tube
Front and back burners (2)
Center burner
1/4-20 stainless steel wing nuts (2)
Spider Stopper Guards (3)
Manifold assembly
Manifold bracket
Igniter
Igniter lock nut
Gas catcher ignition chamber
Igniter wire (black)
Igniter wire (white)
Right frame
Hose
Control panel inserts (2)

WARNING: Use only Weber factory
authorized parts. The use of any part that is
not factory authorized can be dangerous.
This will also void your warranty.

A FINAL WORD
OF THANKS
Thank you for choosing a Weber Barbecue.

Our family here at Weber has worked hard
to produce the highest quality products
for your satisfaction.

While we give much attention to our products, an
occasional error may occur. Our knowledgeable
Customer Service staff is prepared to help you
with any problems with parts or assembly.
Call our toll free number 1-800-446-1071.
For quicker service, please have your owner’s
manual available for reference. We also welcome
any comments or suggestions you might have
regarding our products.
We wish your family the
best in outdoor cooking enjoyment.

Weber-Stephen Products Company
Customer Service Center
200 East Daniels Road
Palatine, Illinois 60067-6266

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Mode                       : UseOutlines
XMP Toolkit                     : 3.1-702
About                           : uuid:cb7865c1-04af-43a3-96b7-8d79a54dd4a1
Keywords                        : Genesis 1000
Producer                        : Acrobat Distiller 3.02
Modify Date                     : 2006:02:06 15:28:47-06:00
Create Date                     : 1998:05:28 15:39:30Z
Creator Tool                    : QuarkXPressª 3.32r5: LaserWriter 8 8.4.3
Metadata Date                   : 2006:02:06 15:28:47-06:00
Document ID                     : uuid:ddb15d49-59cb-4722-a940-76f2cca9420b
Instance ID                     : uuid:a465b69a-ec73-4431-a2b0-77712f98cd31
Format                          : application/pdf
Title                           : Genesis 1000 NG Owners Guide 98613 10/97 PDF File
Creator                         : 
Description                     : Genesis 1000 NG Owners Guide 98613 10/97
Page Count                      : 32
Page Layout                     : SinglePage
Subject                         : Genesis 1000 NG Owners Guide 98613 10/97
Author                          :

EXIF Metadata provided by EXIF.tools

Weber Genesis 1000 Series Natural Gas Barbecue Users Manual NG Owners Guide 98613 10/97 PDF File

1000 Series to the manual ec7c3c65-a57d-470f-a304-f1c8a8aa4964

Navigation menu

Versions of this User Manual:

Views

Navigation