Weed Eater 530084129 Instruction Manual OM, SG10, SG12, TE12, TE35, TE40, XT110, XT110S, XT112, 2003 02, TRIMMERS/EDGERS

TWIST-N-EDGE 530086412 WEEO2003_USen__530084129

TE12 to the manual 98ade308-1d7c-4aa4-871e-76eeecd5528f

: Weed-Eater Weed-Eater-530084129-Instruction-Manual-204763 weed-eater-530084129-instruction-manual-204763 weed-eater pdf

Open the PDF directly: View PDF .
Page Count: 8

SG / TE / XT Series

RTrademark

Instruction Manual

ENGLISH

530084129 2/11/03

Please do not return unit to retailer.

Por favor, no devuelva el aparato al lugar de compra.

Veuillez ne pas retourner l’outil au détaillant.

1-800-554-6723

www.weedeater.com

Electrolux Home Products, Inc.

250 Bobby Jones Expressway

Augusta, GA 30907

Electrolux Canada Corporation

6150 McLaughlin Road

Mississauga, Ontario L5R 4C2

Copyright E2003 Electrolux Home Products, Inc.

WARNING:

Read and follow all Safety Rules and Operating Instructions be-

fore using this product. Read instructions carefully before assem-

bling.Failuretodosocanresultinseriousinjury.

2

SAFETY RULES

WARNING: When using electric

gardening appliances, basic safety pre-

cautions should always befollowed to re-

duce the risk of fire, electric shock, and

serious injury. Read and follow all

instructions.

SAFETY INFORMATION

ON THE UNIT

This power unit can be dangerous! Opera-

tor is responsible for following the warnings

and instructions in this manual and on the

unit. Read entire instruction manual before

using unit! Be thoroughly familiar with the

controls and the proper use of the unit. Re-

strict the use of this unit to persons who

read, understand, and follow unit and

manual warning and instructions. Never al-

low children to operate this unit. Close

attention is necessary when used near

children.

DANGER: Never useblades orflail-

ing devices. Unit is designedfor line trim-

mer use only. Use of any other accesso-

ries or attachments will increase the risk

of injury.

WARNING: Trimmer line throws

objects violently. You and others can be

blinded/injured. Wear safety glasses,

boots, and leg protection. Keep body

parts clear of rotating line.

Safety Glasses or similar eye protection

Boots

Hazard Zone

15 m

50 ft.

Keep children, bystanders, and animals

50 feet (15 meters) away. If approached

stop unit immediately.

If situations occur which are not covered

in this manual, use care and good

judgement. If you need assistance,

contact your Authorized Service Dealer

or call 1-800-554-6723.

OPERATOR SAFETY

SDress properly. Always wear safety

glasses or similar eye protection when

operating or performing maintenance on

your unit. (Safety glasses are available.)

Always wear face or dust mask if opera-

tion is dusty. Always wear heavy, long

pants, long sleeves, boots, and gloves.

Do not go barefoot or wear sandals.

SSecure hair above shoulder length.

Secure or remove loose clothing and

jewelry or clothing with loosely hanging

ties, straps, tassels, etc. They can be

caught in moving parts.

SBeing fully covered also helps protect

you from debris and pieces of toxic

plants thrown by spinning line.

SStay alert.Do not operate unit when you

are tired, ill, upset or under the influence

of alcohol, drugs, or medication. Watch

what you are doing; use common sense.

SAvoid unintentional starting of the unit.

Never carry unit with your finger on the

switch. Be sure the switch is in OFF

position and never touch the switch

when connecting extension cord.

ELECTRICAL SAFETY

WARNING: Avoid a dangerous en-

vironment. To reduce the risk of electri-

cal shock, do not use in rain, in damp or

wet locations, or around swimming

pools, hot tubs, etc. Do not expose to

snow, rain, or water to avoid the possibil-

ity of electrical shock.

SUse a voltage supply shown on unit.

SAvoid dangerous situations. Do not use

in the presence of flammable liquids or

gases to avoid creating a fire or explo-

sion and/or causing damage to unit.

STo reduce the risk of electrical shock, this

appliance has a polarized plug (one

blade is wider than the other) and will re-

quire the use of a polarized extension

cord. The appliance plug will fit into a po-

larized extension cord only one way. If

the plug does not fit fully into the exten-

sion cord, reverse the plug. If the plug still

does not fit, obtain a correct polarized ex-

tension cord. A polarized extension cord

will require the use of a polarized wall

outlet. This plug will fit into the polarized

wall outlet only one way. If plug does not

fit fully into the wall outlet, reverse the

plug. If the plug still does not fit, contact a

qualified electrician to install the proper

wall outlet. Do not change the equipment

plug, extension cord receptacle, or ex-

tension cord plug in any way.

STo reduce risk of electrical shock, use

extension cords specifically marked as

suitable for outdoor appliances having

3

electrical rating not less than the rating

of unit. Cord must be marked with suf-

fix “W--A” (in Canada “W”). Make sure

your extension cord is in good condi-

tion. Inspect extension cord before use

and replace if damaged. Do not use a

damaged cord. Cord insulation must

be intact with no cracks or deteriora-

tion. Plug connectors must be undam-

aged. An undersized extension cord

will cause a drop in line voltage result-

ing in loss of power and overheating. If

in doubt, use the next heavier gauge.

The lower the gauge number, the

heavier the cord (see SELECT AN EX-

TENSION CORD). Do not use multiple

cords.

SDo not abuse cord. Never carry the unit

by the extension cord or yank exten-

sion cord to disconnect unit.

SUse cord retainer to prevent discon-

nection of extension cord from unit.

See ATTACH THE EXTENSION CORDTO

YOUR TRIMMER in the OPERATION sec-

tion.

SDo not use the unit if the switch does

not turn the unit on and off properly. Re-

pairs to the switch must be made by

your authorized service dealer.

SKeep the extension cord clear of oper-

ator and obstacles at all times. Do not

expose cords to heat, oil, water, or

sharp edges.

STo avoid the possibility of electric

shock, avoid body contact with any

grounded conductor, such as metal

fences or pipes.

SGround Fault Circuit Interrupter (GFCI)

protection should be provided on cir-

cuit or outlet to be used. Receptacles

are available having built-in GFCI

protection and may be used for this

measure of safety.

UNIT SAFETY

SInspect unit before use. Replace dam-

aged parts. Make sure all handles,

guards, and fasteners are in place and

securely fastened. Parts that are dam-

aged must be repaired or replaced by

an authorized service dealer. This in-

cludes head parts that are cracked, or

chipped, guards, and any other part

that is damaged.

SDo not repair unit yourself.

SUse only 0.065” (1.65 mm) diameter

recommended trimmer line (see ACCE-

SORIES). Never use wire, rope, string,

etc.

SUse specified trimmer spool. Make

sure spool is properly installed and all

parts are securely fastened.

SUse only recommended Weed Eaterr

replacement parts and accessories.

CUTTING SAFETY

SInspect area to be cut. Remove objects

(rocks, broken glass, nails, wire, string,

etc.) which can be thrown or become

entangled in cutting head.

SDo not overreach or stand on unstable

support. Keep firm footing and balance.

SKeep the cutting head below waist lev-

el. Do not raise handles above your

waist. Cutting head can come danger-

ously close to your body.

SKeep away from cutting head and spin-

ning line.

SUse unit properly. Use only for trim-

ming, edging, and mowing. Do not

force unit; it will do the job better and

with less risk of injury at the rate for

which it was designed.

SUse only in daylight or in good artificial

light.

MAINTENANCE SAFETY

WARNING: Disconnect unit from

the power supply before performing

maintenance, or when changing trimmer

line.

SMaintain unit according to recom-

mended procedures. Keep cutting line

at proper length. Follow instructions for

changing trimmer line.

SHave all service and maintenance not

explained in this manual performed by

an authorized service dealer to avoid

creating a hazard.

SNever douse or squirt the unit with water

or any other liquid. Clean unit and labels

with a damp sponge. Keep handles dry,

clean, and free from oil and grease.

SKeep the air vents clean and free from

debris to avoid overheating the motor.

Clean after each use.

TRANSPORTING AND STORAGE

SStop the unit and disconnect the power

source when not in use.

SCarry the unit with motor stopped.

SStore the unit so that the line limiter

blade (on underside of shield) cannot

cause injury.

SStore unit indoors in a high, dry place

out of the reach of children. Store unit

unplugged.

DOUBLE INSULATION

CONSTRUCTION

This unit is double insulated to help pro-

tect against electric shock. Double in-

sulation construction consists of two

separate “layers” of electrical insulation

instead of grounding.

4

Tools built with this insulation system are

not intended to be grounded. No ground-

ing means is provided on this unit, nor

should a means of grounding be added

to this unit. As a result, the extension

cord used with your unit can be plugged

into any standard 120 volt electrical out-

let.

Safety precautions must be observed

when operating any electrical tool. The

double insulation system only provides

added protection against injury resulting

from an internal electrical insulation failure.

WARNING: All electrical repairs to

this unit, including housing, switch, mo-

tor, etc., must be diagnosed and repaired

by qualified service personnel. Replace-

ment parts for a double insulated ap-

pliance must be recommended by the

manufacturer. A double insulated ap-

pliance is marked with the words “double

insulation” or “double insulated.” the

symbol (square within a square) may

also be marked onthe appliance. Failure

to have the unit repaired by qualified ser-

vice personnel can cause the double in-

sulation construction to become ineffec-

tive and result in serious injury.

SAVE THESE INSTRUCTIONS

ASSEMBLY

WARNING: If you receive your unit

assembled, check each step to insure

your unit is properly assembled. Follow

all safety information in the manual and

on unit.

WARNING: The shield must be

properly installed. The shield provides

partial protection from the risk of thrown

objects to the operator and others. Your

unit is equipped with a line limiter blade,

which cuts excess line to the proper

length while running. The line limiter

blade (on underside of shield) is sharp

and can cut you.

NOTE: If shield is not properly installed,

damage to unit (including motor failure)

will result.

CAUTION: Sharp line limiter blade

ALIGN INSTALLATION ARROWS

Twist shield in

direction of

arrow to assemble

Place handle in

comfortable

position and

tighten securely.

NOTE: SG & XT units are equipped with

an extendable tube. Extend the tube until

it snaps into place. Without the tube fully

extended the Twist ’N Edge feature on

the XT series will not operate.

Extendable tube

(Some models)

CAUTION: The tube must be fully ex-

tended for the unit to operate correctly.

USING YOUR UNIT

Use only a voltage supply as specified

on your unit.

SELECT AN EXTENSION CORD

Extension Cord Gauge Chart

Length of Cord Gauge

25 Ft. (7.5 m)

50 Ft. (15 m)

100 Ft. (30 m)

18 Gauge

16 Gauge

16 Gauge

Extension cords are available for this

unit.

ATTACH THE EXTENSION

CORD TO YOUR TRIMMER

Loop your extension cord through the

handle and around the hook. Insure the

plug and cord are firmly and fully en-

gaged.

5

CORRECT OPERATING POSITION

Trimming Edging

(XT & TE)

WARNING: Always wear eye pro-

tection. Never lean over the trimmer

head. Rocks or debris can ricochet or be

thrown into eyes and face and cause

blindness or other serious injury.

When operating unit, stand as shown and

check for the following:

SWear eye protection and heavy clothing.

SHold trigger handle with right hand and

assist handle with left hand.

SKeep unit below waist level.

SCut from your right to your left to ensure

debris is thrown away from you. With-

out bending over, keep line near and

parallel to the ground (perpendicular

when edging) and not crowded into

material being cut.

ADJUSTING UPPER HANDLE

(XT Series only)

SPress button located on the underside

of the upper handle and extend handle

to a comfortable position.

Button

ADVANCING THE CUTTING LINE

To advance the line, tap the bottom of the

cutting head on the ground while the trim-

mer is running at full speed. The metal

blade attached to the shield will cut the

line to the proper length.

Cutting

Head

TAP

Metal Blade

TWIST ‘N EDGErFEATURE

XT & TE series units are equipped with a

button on the side of the unit. If your unit

includes this feature you can press this

button and twist the lower portion 180_

counterclockwise into an edging posi-

tion.

Twist ‘N Edge Button

MAINTENANCE

WARNING: Disconnect power

source before performing maintenance.

GENERAL RECOMMENDATIONS

The warranty on this unit does not cover

items that have been subjected to opera-

tor abuse or negligence. To receive full

value from the warranty, the operator

must maintain unit as instructed in this

manual. Various adjustments will need to

be made periodically to properly main-

tain your unit.

BEFORE EACH USE

CHECK FOR LOOSE FASTENERS

AND PARTS

SHousing Screws

SAssist Handle

SDebris Shield

CHECK FOR DAMAGED OR

WORN PARTS

Contact an authorized service dealer for

replacement of damaged or worn parts.

STrigger Switch -- Ensure switch func-

tions properly by pressing and releas-

ing the trigger switch. Make sure motor

stops.

SDebris Shield -- Discontinue use of unit

if debris shield is damaged.

AFTER EACH USE

INSPECT AND CLEAN UNIT AND LA-

BELS

SAfter each use, inspect complete unit

for loose or damaged parts. Clean the

unit using a damp cloth with a mild de-

tergent.

SWipe off unit with a clean dry cloth.

6

SERVICE

REPLACING THE LINE

SDisconnect unit fromthe powersource.

SRemove the spool by firmly pulling on

the tap button.

SClean entire surface of hub and spool.

SReplace with a pre-wound spool, or cut a

length of 30 feet of 0.065 diameter Weed

Eaterrbrand line. Use of heavier line

could overload and damage the unit.

Never use wire, rope, string, etc., which

can break off and become a dangerous

missile.

SInsert one end of the line about 1/2 inch

(1 cm) into the small slot inside the spool.

Small

Hole Spool

SWind the line evenly and tightly onto

the spool. Wind in the direction of the

arrow found on the spool.

SPush the line into the notch, leaving 3

to 5 inches (7 -- 12 cm) unwound.

SInsert the line into the exit hole in the

hub as shown in the illustration.

Hub Line exit hole

Line in

Notch

SAlign the notch with the line exit hole.

SPush the spool into the hub until it

snaps into place, while keeping light

tension on the end of the line.

SPull onthe line extending outside of the

hub to release it from the notch; other-

wise, the unit will not function properly.

STORAGE

WARNING: Perform the following

steps after each use.

SStop the unit and disconnect the power

source when not in use.

SCarry the unit with motor stopped.

SStore the unit so the line limiter blade

cannot cause injury.

SStore unit and extension cord indoors

in a high, dry place out of the reach of

children. Store unit unplugged.

SStore unit with all guards in place. Posi-

tion unit so that any sharp object can-

not accidentally cause injury.

NEED ASSISTANCE?

For assistance, or a replacement part

call: 1-800-554-6723.

Safety Glasses 952701645

Spool with 30’ line 952701663

50’ coil of bulk line. 952701550

100’ coil of line. 952701533

200’ coil of line. 952701594

7

TROUBLE CAUSE REMEDY

Semi-automatic

head stops

under a load or

does not turn

when switch is

pressed.

1. Allow tip of line to do the cutting.

2. Contact your authorized service dealer.

3. Check Breaker Box.

4. Remove debris.

Line does not

advance or

breaks while

cutting.

1. Check line routing.

2. Rewind line tightly and evenly.

3. Use only .065 in. (1.65mm) dia. line.

4. Remove cover and pull 4 in.

(10 cm) of line out of head.

5. Clean unit.

Line welds onto

spool. 1. Use only .065 in. (1.65mm) dia. line.

2. Replace with correct spool.

3. Cut with tip of line fully extended.

Line releases

continuously. 1. Check line routing.

2. Replace spool.

Line pulls back

into head. 1. Too little line outside

of head.

2. Line size incorrect.

1. Remove cover and pull 4 in.

(10 cm) of line outside of head.

2. Use only .065 in. (1.65 mm) dia. line.

TROUBLESHOOTING TABLE

1. Line improperly

routed in head.

2. Spool damaged.

1. Line size is incorrect.

2. Incorrect spool.

3. Line is being crowded

against material being

cut.

1. Line improperly routed

in head.

2. Line improperly

wound onto spool.

3. Incorrect line size

4. Not enough line

outside of head.

5. Dirt buildup on unit.

1. Crowding trimmer line

against material being

cut.

2. Electrical failure.

3. Thrown circuit breaker.

4. Debris stopping head.

Line usage is

excessive. 1. Check line routing.

2. Replace spool.

3. Cut with tip of line fully extended.

4. Replace spool.

1. Line improperly routed

in head.

2. Line size is incorrect.

3. Crowding line against

material being cut.

4. Spool worn or damaged.

WARNING: Always stop unit and disconnect from the power source before

performing all of the recommended remedies below except remedies that re-

quire operation of the unit.

8

LIMITED WARRANTY

ELECTROLUX HOME PRODUCTS,

INC., warrants to the original purchaser

that each new Weed Eaterrbrand elec-

tric or cordless product is free from de-

fects in material and workmanship and

agrees to repair or replace under this

warranty any defective Weed Eater

brand electric product within two (2)

years from the original date of purchase.

If your Weed Eater brand electric or

cordless product should fail within the

limited warranty period, return it, com-

plete, prepaid, with proof of purchase, to

the dealer from whom it was purchased

for repair or replacement at the option of

ELECTROLUX HOME PRODUCTS,

INC.

This warranty is not transferable and

does not cover damage or liability

caused by improper handling, improper

maintenance or the use of accessories

and/or attachments not specifically rec-

ommended by ELECTROLUX HOME

PRODUCTS, INC., for this electric prod-

uct. Additionally, this warranty does not

cover parts that will wear and require re-

placement with reasonable use during

the warranty period. This warranty does

not cover predelivery set--up or normal

adjustments explained in the instruction

manual.

THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY HAVE

OTHER RIGHTS WHICH VARY FROM

STATE TO STATE.

NO CLAIMS FOR CONSEQUENTIAL OR

OTHER DAMAGES WILL BE ALLOWED,

AND THERE ARE NO OTHER EXPRESS

WARRANTIES EXCEPT THOSE EX-

PRESSLY STIPULATED HEREIN.

SOME STATES DO NOT ALLOW LIMITA-

TIONS ON HOW LONG AN IMPLIED WAR-

RANTY LASTS OR THE EXCLUSION OR

LIMITATIONS OF INCIDENTAL OR CONSE-

QUENTIAL DAMAGES, SO THE ABOVE

LIMITATIONS OR EXCLUSION MAY NOT

APPLY TO YOU.

The policy of ELECTROLUX HOME

PRODUCTS, INC., is to continuously im-

prove its products. Therefore, ELEC-

TROLUX HOME PRODUCTS, INC., re-

serves the right to change, modify, or

discontinue models, designs, specifica-

tions, and accessories of all products at

any time without notice or obligation to

any purchaser.