Weed Eater 530163804 Instruction Manual OM, BV200, BV1650, BV1800, BV1850, BV2000, 2004 02, BLOWERS

530163804 to the manual 67c05684-1ce3-4b38-a763-2af3d243a7cc

: Weed-Eater Weed-Eater-530163804-Instruction-Manual-204333 weed-eater-530163804-instruction-manual-204333 weed-eater pdf

Open the PDF directly: View PDF .
Page Count: 11

IMPORTANT MANUAL -- Do not throw away

MANUAL IMPORTANTE -- No lo descarte

MANUEL IMPORTANT -- À Conserver

RTrademark

ENGLISH ESPAÑOL FRANÇAIS

Electrolux Home Products, Inc.

104 Warren Road

Augusta, GA 30907

WARNING:

Read and follow all Safety Rules and Operating Instructions before

using this product. Failure to do so can result in serious injury.

ADVERTENCIA:

Lea el manual de instrucciones y siga todas las advertencias e

instrucciones de seguridad. El no hacerlo puede resultar en lesiones

graves.

AVERTISSEMENT:

Veuillez lire le manuel d’instructions et bien respecter tous les

avertissements et toutes les instructions de sécurité. Tout défaut

de le faire pourrait entraîner des blessures graves.

Copyright E2004 Electrolux Home Products, Inc. 530163804 2/2/04

Instruction Manual

Manual de Instrucciones

Manuel d’Instructions

BV200 / BV1650 / BV1800

BV1850 / BV2000

-- 2 --

SAFETY RULES

WARNING: Failure to follow all

Safety Rules and Precautions can result in

serious injury.

KNOW YOUR UNIT

SRead your instruction manual carefully until

you completely understand and can follow

all warnings and safety rules before operat-

ing the unit.

DRestrict unit to users who understand and

will follow all warnings and safety rules in

this manual.

WARNING: Inspect area before start-

ing unit. Remove all debris and hard objects

such as rocks, glass, wire, etc. that can rico-

chet, be thrown, or otherwise cause injury or

damage during operation.

Use your unit as a blower for:

DSweeping debris or grass clippings from

driveways, sidewalks, patios, etc.

DBlowing grass clippings, straw, or leaves into

piles, around joints, or between bricks.

Use your unit as a vacuum for:

DPicking up dry material such as leaves,

grass, small twigs, and bits of paper.

DFor best results during vacuum use, operate

your unit at high speed.

DMove slowly back andforth over the mate-

rial as you vacuum. Avoid forcing the unit

into a pile of debris as this can clog the unit.

DKeep the vacuum tube about an inch above

thegroundforbestresults.

PLAN AHEAD

DAlways wear eye protection when operat-

ing, servicing, or performing maintenance

on unit. Wearing eye protection will help to

prevent rocks or debris from being blown or

ricocheting into eyes and face which can

result in blindness and/or serious injury.

Eye protection should be marked Z87.

DAlways wear foot protection. Do not go

barefoot or wear sandals.

DAlways wear respirator or face mask when

working with unit in dusty environments.

DSecure hair above shoulder length. Secure

or remove jewelry, loose clothing, or cloth-

ing with loosely hanging straps, ties, tas-

sels, etc. They can be caught in moving

parts.

DDo not operate unit when you are tired, ill, up-

set, or if you are under the influence of alco-

hol, drugs, or medication.

DKeep children, bystanders, and animals

away from work area a minimum of 30 feet

(10 meters) when starting or operating unit.

Do not point the blower nozzle in the direc-

tion of people or pets.

HANDLE FUEL WITH CAUTION, IT IS

HIGHLY FLAMMABLE

DEliminate all sources of sparks or flame (in-

cluding smoking, open flames, or work that

can cause sparks) in the areas where fuel is

mixed, poured, or stored.

DMix and pour fuel in an outdoor area; store

fuel in a cool, dry, well ventilated place; use

an approved, marked container for all fuel

purposes.

DDo not smoke while handling fuel or while

operating the unit.

DMake sure the unit is properly assembled

and in good operating condition.

DDo not fill fuel tank while engine is hot or

running.

DAvoid spilling fuel or oil. Wipe up fuel spills

before starting engine.

DMove at least 10 feet (3 meters) away from

fuel and fueling site before starting engine.

DAlways store gasoline in a container ap-

proved for flammable liquids.

OPERATE YOUR UNIT SAFELY

WARNING: Stop the engine before

opening the vacuum inlet door. The engine

must be stopped and the impeller blades no

longer turning to avoid serious injury from the

rotating blades.

DInspect unit before each use for worn,

loose, missing, or damaged parts. Do not

use until unit is in proper working order.

DKeep outside surfaces free of oil and fuel.

DNever start or run engine inside a closed

room, building or other unventilated area.

Breathing exhaust fumes can kill.

DTo avoid static electricity shock, do not

wear rubber gloves or any other insulated

gloves while operating unit.

DDo not set unit on any surface except a

clean, hard area while engine is running.

Debris such as gravel, sand, dust, grass,

etc. could be picked up by the air intake and

thrown out through discharge opening,

damaging unit, property, or causing serious

injury to bystanders or operator.

DAvoid dangerous environments. Do notuse

in unventilated areas or where explosive

vapors or carbon monoxide build up could

be present.

DDo not overreach or use from unstable sur-

faces such as ladders, trees, steep slopes,

rooftops, etc. Keepfirm footing andbalance

at all times.

DNever place objects inside the blower

tubes; always direct the blowing debris

away from people, animals, glass, andsolid

objects such as trees, automobiles, walls,

etc. The forceof air can cause rocks, dirt, or

sticks to be thrown or to ricochet which can

hurt people or animals, break glass, or

cause other damage.

DNever run unit without the proper equip-

ment attached. When using your unit as a

blower, always install blower tubes. When

using your unit as a vacuum, always install

vacuum tubes and vacuum bag assembly.

Make sure vacuum bag assembly is com-

pletely zipped.

DCheck air intake opening, blower tubes,

vacuum tubes, and elbow tube frequently,

always with engine stopped and spark plug

-- 3 --

disconnected. Keep vents and discharge

tubes free of debris which can accumulate

and restrict proper air flow.

DNever place any object in the air intake open-

ing as this could restrict proper air flow and

cause damage to the unit.

DNever use for spreading chemicals, fertiliz-

ers, or other substances which may contain

toxic materials.

DTo avoid spreading fire, do not use nearleaf

or brush fires, fireplaces, barbecue pits,

ashtrays, etc.

DUse only for jobs explained in this manual.

MAINTAIN YOUR UNIT PROPERLY

DHave all maintenance other than the rec-

ommended procedures described in the in-

struction manual performed by an autho-

rized service dealer.

DDisconnect spark plug before performing

maintenance except for carburetor adjust-

ments.

DUse only recommended Weed Eater!re-

placement parts; use of any other parts

may void your warranty and cause damage

to your unit.

DEmpty fuel tank before storing the unit. Use

up fuel left in carburetor by starting engine and

letting it run until it stops.

DDo not use any accessory or attachment

other than those recommended by manufac-

turer for use with your unit.

DDo not store the unit or fuel in a closed area

where fuel vapors can reach sparks or an

open flame from hot water heaters, electric

motors or switches, furnaces, etc.

DStore in a dry area out of reach of children.

SPECIAL NOTICE: Exposure to vibra-

tions through prolongeduse of gasoline pow-

ered hand tools could cause blood vessel or

nerve damage in the fingers, hands, and

joints of people prone to circulation disorders

or abnormal swelling. Prolonged use in cold

weatherhas beenlinked to blood vessel dam-

age in otherwise healthy people. If symptoms

occur such as numbness, pain, loss of

strength, change in skin color or texture, or

loss of feeling in the fingers, hands, or joints,

discontinue the use of this tool and seek

medical attention. An antivibration system

does not guarantee the avoidance of these

problems. Users who operatepower tools on

a continual and regular basis must monitor

closely their physical condition and the condi-

tion of this tool.

SPECIALNOTICE:For users on U.S. For-

est Land and in some states, including Cali-

fornia (Public Resources Codes 4442 and

4443), Idaho, Maine, Minnesota, New Jersey,

Oregon, and Washington: Certain internal

combustion engines operated on forest,

brush,and/orgrasscoveredland in theabove

areas are required to be equipped with a

spark arresting screen, maintained in effec-

tive working order, or the engine must be con-

structed, equipped, and maintained for the

prevention of fire. Check with your state or lo-

cal authorities for regulations pertaining to

these requirements. Failure to follow these

requirements is a violation of the law. This unit

is not factory equipped with a spark arresting

screen; however, a spark arresting screen is

available as an optional part.If a spark arrest-

ing screen is required in your area, contact

your authorized service dealer for the correct

kit. The spark arresting screen, blower tubes,

and nozzles must be assembled to unit to be

in full compliance with regulations.

ASSEMBLY

WARNING: Stop engine and be sure

the impeller blades have stopped turning be-

fore opening the vacuum inlet door or at-

tempting to insert or remove the vacuum or

blower tubes. The rotating blades can cause

serious injury. Always disconnect the spark

plug before performing maintenance or ac-

cessing movable parts.

WARNING: If you receive your unit

assembled, check each step to insure your

unit is properly assembled and all fasteners

are secure. Follow all safety information in

the manual and on the unit.

DA standard screwdriver is required for as-

sembly.

BLOWER TUBE ASSEMBLY

1. Align the rib on the blower tube with the

groove in the blower outlet; slide the tube

into place.

NOTE: Knob must be loose enough to allow

blower tube to be inserted in blower outlet.

Loosen knob by turning counterclockwise.

Blower

Tube

Blower

Outlet

Rib

Groove

2. Secure the tube by turning the knob clock-

wise.

3. To remove the tube, turn the knob counter-

clockwise to loosen the tube; remove the

tube.

VACUUM BAG ASSEMBLY

1. Open the zipper on the vacuum bag and

insert the elbow tube.

2. Push the small end of the elbow tube

through the small opening in the bag.

-- 4 --

Small

Opening

Zipper

Opening

Elbow

Tube

Rib

NOTE: Make sure edgeofthesmall opening

is flush against the flared area of the elbow

tube, and the rib on the elbow tube is on the

bottom.

3. Close the zipper on thebag.Make sure the

zipper is closed completely.

4. Remove blower tube from engine.

Rib

Groove

5. Insert theelbowtube into thebloweroutlet.

Make sure elbow tube rib is aligned with

the blower outlet groove.

6. Turnknob clockwise tosecure elbow tube.

VACUUM TUBE ASSEMBLY

WARNING: Stop engine and be sure

the impeller blades have stopped turning be-

fore opening the vacuum inlet door or at-

tempting to insert or remove the vacuum or

blower tubes. The rotating blades can cause

serious injury.

1. Align the lower vacuum tube as shown.

Push lower vacuum tube into upper vacu-

um tube.

Lower Vacuum Tube

Upper Vacuum

Tube

2. Insert the tip of a screwdriver into thelatch

area of the vacuum inlet.

Latch Area

Blower

Outlet

Vacuum

Inlet Cover

Latch

Area

3. Gently tilt the handle of the screwdriver to-

ward the back of the unit to release the

latch while pulling up on the vacuum inlet

cover with your other hand.

4. Hold the vacuum inlet cover open until up-

per vacuum tube is installed.

Vacuum Inlet

Vacuum

Inlet

Cover

Retaining Post

5. Place the hooks of the upper vacuum tube

on the retaining posts of the unit.

6. Pivot the tube until it is secured to the

blower unit by the vacuum inlet latch.

Retaining

Post

Hook

Inlet Cover

Latch

PIVOT

HOW TO CONVERT UNIT FROM

VACUUM USE TO BLOWER USE

1. Remove the vacuum tubes by inserting

the tip of a screwdriver into the latch area

of the vacuum inlet.

2. Gently tilt handle of screwdriver toward

the back of the unit to release the latch

while pulling up on the upper vacuum tube

with your other hand.

Latch Area

3. Remove the vacuum bag.

4. Close the vacuum inlet cover and make

sure it is latched closed.

5. Reinstall the blower tube (see BLOWER

TUBE ASSEMBLY).

-- 5 --

SHOULDER STRAP ADJUSTMENT

1 Hold the unit as shown with the muffler side

facing away from your body and clothes.

2. Pass the shoulder strap over your head

and onto your right shoulder.

3. Extend your left arm toward the rear ofthe

vacuum bag.

4. Adjust shoulder strap until the vacuum

bag/shoulder strap seam lies between

your thumb and index finger.

5. Make sure air flows freely from the elbow

tube into bag. If bag is kinked, the unit will

not operate properly.

OPERATION

KNOW YOUR BLOWER

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.

Compare the illustrations with your unit to familiarize yourself with the location of the various controls

and adjustments. Save this manual for future reference.

Choke Lever

Fuel Mix

Fill Cap

Starter

Rope

Throttle

Lever

Spark Plug

Blower

Tube

Primer Button

Rear

Handle

Lower

Vacuum Tube

Upper

Vacuum Tube

Vacuum Bag

Elbow Tube

THROTTLE LEVER

The THROTTLE LEVER is used to select the

desired engine speed and to stop the engine.

Move thethrottle lever to the positionfor

full speed operation. Move the throttle lever

to the position for idle speed. To stop the

engine, move the throttle lever to the STOP

position.

PRIMER BUTTON

The PRIMER BUTTON removes air from the

carburetor and fuel lines and fills them with fuel.

This allows you to start the engine with fewer

pulls on the starter rope. Activate primer button

by pressing it and allowing it to return to its origi-

nal position.

CHOKE LEVER

The CHOKE helps to supply fuel to the engine

to aid in cold starting. Activate the choke by

moving the choke lever to the FULL CHOKE

position. After engine attempts to start, move the

choke lever to the HALF CHOKE position.

Once engine starts, move choke lever to the

RUN position.

-- 6 --

OPERATING POSITION

Blower

Eye

Protection

Vacuum

OPERATING TIPS

SWhile vacuuming or blowing debris, hold

the unit with the muffler side facing away

from your body and clothes (see OPERAT-

ING POSITION illustration above).

STo reduce the risk of hearing loss

associated with sound level(s), hearing

protection is required.

STo reduce the risk of injury associated with

contacting rotating parts, stop the engine be-

fore installing or removing attachments. Do

not operate without guard(s) in place.

SOperate power equipment only at reasonable

hours--not early in the morning or late at night

when people might be disturbed. Comply with

times listed in local ordinances. Usual recom-

mendations are 9:00 a.m. to 5:00 p.m.,

Monday though Saturday.

STo reduce noise levels, limit the number of

pieces of equipment used at any one time.

STo reduce noise levels, operate power

blowers at the lowest possible throttle

speed to do the job.

SUse rakes and brooms to loosen debris be-

fore blowing.

SIn dusty conditions, slightly dampen sur-

faces or use a mister attachment when wa-

ter is available.

SConserve water by using power blowers

instead of hoses for many lawn and garden

applications, including areas such as gutters,

screens, patios, grills, porches, and gardens.

SWatch out for children, pets, open windows,

or freshly washed cars. Blow debris away

safely.

SUse the full blower nozzle extension so the

air stream can work close to the ground.

SAfter using blowers and other equipment,

CLEAN UP! Dispose of debris in trash re-

ceptacles.

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel

information in the safety rules before you be-

gin. If you do not understandthe safety rules,

do not attempt to fuel your unit. Call

1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slowly

when refueling.

This engine is certified to operate on

unleaded gasoline. Before operation,

gasoline must be mixed with a good quality

synthetic 2-cycle air-cooled engine oil

designed to be mixed at a ratio of 40:1.

Poulan/Weed Eater brand synthetic oil is

recommended. Mix gasoline and oil at a ratio

of 40:1. A 40:1 ratio is obtained by mixing 3.2

ounces (95 ml) of oil with 1 gallon (4 liters) of

unleaded gasoline. DO NOT USE

automotive oil or boatoil. These oils will cause

engine damage. When mixing fuel, follow

instructions printed on container. Once oil is

added to gasoline, shake container

momentarily to assure that the fuel is

thoroughly mixed. Always read and follow the

safety rules relating to fuel before fueling your

unit.

IMPORTANT

Experience indicates that alcohol blended

fuels (called gasohol or using ethanol or

methanol) can attract moisture which leads to

separation and formation of acids during

storage. Acidic gas can damage the fuel

system of an enginewhile in storage. To avoid

engine problems, empty the fuel system

before storagefor 30days or longer. Drain the

gas tank, starttheengine andlet it run until the

fuel lines and carburetor are empty. Use fresh

fuel next season. Never use engine or

carburetor cleaner products in the fuel tank or

permanent damage may occur.

NOTE: Unit must be placed on its side when

adding fuel (see illustration below).

TO STOP THE ENGINE

DTo stop the engine, move the throttle lever

to the STOP position.

BEFORE STARTING THE ENGINE

WARNING: YouMUSTmakesure

the tubes are secure before using the unit.

DFuel engine. Move at least 10 feet (3 me-

ters) away from the fueling site.

DHold the unit in the starting position as

shown. Make sure the blower end is di-

rected away from people, animals, glass,

and solid objects.

-- 7 --

Blower

Vacuum

STARTING POSITION

WARNING: When starting engine,

holdthe unit as illustrated. Donot set unit onany

surface except a clean, hard area when starting

engine or while engine is running. Debris such

as gravel, sand, dust, grass, etc. could be

picked up by the air intake and thrown out

through the discharge opening, damaging the

unit or property, or causing serious injury to by-

standers or the operator.

STARTING A COLD ENGINE

1. Move throttle lever to the position.

2. Move choke lever to the FULL CHOKE

position.

3. Slowly press the primer button 8 times.

Throttle Lever

Choke Lever

Primer Button

4. Pull starter rope sharply until engine at-

tempts to run, but no more than5 pulls (be-

low 30_F, 8 pulls).

NOTE:If engine attempts to start before the

5th pull, go to next step immediately.

5. Move the choke lever to the HALF

CHOKE position.

6. Pull the starter rope sharply until the en-

gine runs, but no more than 5 pulls (below

30_F, 10 pulls).

7. After a 5 second warm--up, move the

choke lever to the RUN position.

8. Allow the unit to run for 30 more seconds

at the RUN position before moving the

throttle lever to position.

If engine has not started after 5 pulls (at HALF

CHOKE), repeat STARTING A COLD ENGINE

procedure. If engine still does not start, proceed

to STARTING A FLOODED ENGINE.

9. To stop the engine, move the throttle lever to

the STOP position.

STARTING A WARM ENGINE

NOTE: If fuel tank is empty, add fuel; then,

follow STARTING A COLD ENGINE proce-

dure. Do not fill fuel tank while engine is hot.

1. Move throttle lever to the position.

2. Pull starter rope sharply until engine runs,

but no more than 5 pulls.

NOTE:If engine has not started, pull starter

rope 5 more pulls. If engine still does not run,

it is probably flooded.

3. To stop the engine, move the throttle lever to

the STOP position.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the

choke lever in the RUN position. Move throttle

lever to the fast position ; then, pull rope

until engine starts. After engine starts, move the

throttle lever to the slow position to allow

engine to idle.

Starting could require pulling the starter rope

many times depending on how badly the unit is

flooded.

If unit still doesn’t start refer to the TROUBLE-

SHOOTING TABLE or call 1-800-554-6723.

MAINTENANCE

WARNING: Avoid touching muffler

unless engine and muffler are cold. A hot

muffler can cause serious burns.

WARNING: Stop engine and be sure

the impeller blades have stopped turning be-

fore opening the vacuum inlet door or at-

tempting to insert or remove the vacuum or

blower tubes. The rotating blades can cause

serious injury. Always disconnect the spark

plug before performing maintenance or ac-

cessing movable parts.

GENERAL RECOMMENDATIONS

Thewarranty onthis unit does not cover items

that have been subjected to operator abuse

or negligence. To receive full value from the

warranty, the operator must maintain unit as

instructed in this manual. Various adjust-

ments will need to be made periodically to

properly maintain your unit.

CHECK FOR LOOSE

FASTENERS AND PARTS

SSpark Plug Boot

SAir Filter

SHousing Screws

SMuffler

CHECK FOR DAMAGED OR WORN

PARTS

Contact an authorized service dealer for re-

placement of damaged or worn parts.

SFuel Tank -- Do not use unit if fuel tank shows

signs of damage or leaks.

SVacuum Bag -- Do not use vacuum bag if it

is torn or damaged.

-- 8 --

INSPECT AND CLEAN UNIT AND

DECALS

SAfter each use, inspect complete unit for

loose or damagedparts. Clean the unit and

decals using a damp cloth with a mild deter-

gent.

SWipe off unit with a clean dry cloth.

CLEAN AIR FILTER

Air Filter

Cover

Air Filter Screws

Cleaning the air filter:

A dirty air filter decreases engine perform-

ance and increases fuel consumption and

harmful emissions. Always clean or replace

air filter after every 5 hours of operation or

yearly, whichever comes first.

1. Clean the cover and the area around it to

keep debris from falling into thecarburetor

chamber when the cover is removed.

2. Remove parts as illustrated.

NOTE: Do not clean filter in gasoline or other

flammable solvent. Doing so can create a fire

hazard or produce harmful evaporative emis-

sions.

3. Wash the filter in soap and water.

4. Allow filter to dry.

5. Apply a few drops of oil to the filter;

squeeze filter to distribute oil.

6. Replace parts.

REPLACE SPARK PLUG

Replace spark plug each year to ensure the

engine starts easier and runs better. Set

spark plug gap at 0.025 inch. Ignition timing is

fixed, nonadjustable.

1. Twist, then pull off spark plug boot.

2. Remove spark plug from cylinder and dis-

card.

3. Replace with Champion RCJ-6Y spark

plug and tighten securely with a 3/4 inch

socket wrench.

4. Reinstall the spark plug boot.

REPLACE FUEL FILTER

To replacefuel filter, drain unit by running it dry

of fuel, then remove fuel cap/retainer assem-

bly from tank. Pull filter from tank and remove

it from the fuel line. Install new fuel filter on fuel

line; reinstall parts.

Fuel Line

Fuel Filter

CHECK MUFFLER MOUNTING

SCREWS

Once each year, ensure muffler mounting

screws are secure and tightened properly to

prevent damage.

Mounting

Screw

Holes

Muffler Cover

Screws

1. Loosen and remove the 2 screws from the

muffler cover.

2. Remove the muffler cover.

3. Tighten the 2 muffler mounting screws se-

curely.

4. Reinstall muffler cover and 2 screws.

Tighten securely.

CARBURETOR ADJUSTMENT

There is no screw for idle adjustment on your

blower. The throttle lever is used to control

engine speed. The throttle lever can be

placed in one of four positions: STOP, IDLE

or , FULL THROTTLE or , and one

intermittent position. If your enginewill notrun

properly or you require further assistance,

contact an authorized service dealer or call

1--800--554--6723.

STORAGE

WARNING: Perform the following

steps after each use:

SAllow engine to cool, and secure the unit

before storing or transporting.

SStore unit and fuel in a well ventilated area

where fuel vapors cannot reach sparks or

open flames from water heaters, electric

motors or switches, furnaces, etc.

SStore unit with all guards in place. Position

unit so that any sharp object cannot acci-

dentally cause injury.

SStore unit and fuel well out of the reach of

children.

-- 9 --

SEASONAL STORAGE

Prepare unit for storage at end of season or if

it will not be used for 30 days or more.

If your unit is to be stored for a period of time:

SClean the entire unit before lengthy stor-

age.

SStore in a clean dry area.

SLightly oil external metal surfaces.

FUEL SYSTEM

Under FUELING ENGINE in the OPERA-

TION section of this manual, see message la-

beled IMPORTANT regarding the use of ga-

sohol in your engine.

Fuel stabilizer is an acceptable alternative in

minimizing the formation of fuel gum deposits

during storage. Add stabilizer to gasoline in fuel

tank or fuel storage container. Follow the mix

instructions found on stabilizer container. Run

engine at least 5 minutes after adding stabilizer.

ENGINE

SRemove spark plug and pour1 teaspoon of

40:1, 2-cycle engine oil (air cooled) through

the spark plug opening. Slowly pull the

starter rope 8 to 10 times to distribute oil.

SReplace spark plug with new one of recom-

mended type and heat range.

SClean air filter.

SCheck entire unit for loose screws, nuts,

and bolts. Replace any damaged, broken,

or worn parts.

SAt the beginning of the next season, use

only fresh fuel having the proper gasoline to

oil ratio.

OTHER

SDo not store gasoline from one season to

another.

SReplace your gasoline can if it starts to rust.

TROUBLE CAUSE REMEDY

Engine will not

start. 1. Engine flooded.

2. Fuel tank empty.

3. Spark plug not firing.

4. Fuel not reaching

carburetor.

5. Compression low.

1. See “Starting a Flooded Engine”

in Operation section.

2. Fill tank with correct fuel mixture.

3. Install new spark plug.

4. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

5. Contact an authorized service dealer.

Engine will not

idle properly.

1. Fuel not reaching

carburetor.

2. Carburetor requires

adjustment.

3. Crankshaft seals worn.

4. Compression low.

1. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

2. Contact an authorized service dealer.

3. Contact an authorized service dealer

4. Contact an authorized service dealer.

1. Air filter dirty.

2. Fuel not reaching

carburetor.

3. Spark plug fouled.

4. Carburetor requires

adjustment.

5. Carbon build up.

6. Compression low.

Engine will not

accelerate,

lacks power, or

dies under a

load.

1. Clean or replace air filter.

2. Check for dirty fuel filter; replace.

Check for kinked or split fuel line;

repair or replace.

3. Clean or replace spark plug

and re-gap.

4. Contact an authorized service dealer.

5. Contact an authorized service dealer.

6. Contact an authorized service dealer.

Engine smokes

excessively. 1. Choke partially on.

2. Fuel mixture incorrect.

3. Air filter dirty.

4. Carburetor requires

adjustment.

1. Adjust choke.

2. Empty fuel tank and refill with

correct fuel mixture.

3. Clean or replace air filter.

4. Contact an authorized service dealer.

Engine runs hot. 1. Fuel mixture incorrect.

2. Spark plug incorrect.

3. Carburetor requires

adjustment.

4. Carbon build up.

1. See “Fueling Engine” in Operation

section.

2. Replace with correct spark plug.

3. Contact an authorized service dealer.

4. Contact an authorized service dealer.

TROUBLESHOOTING TABLE

WARNING: Always stop unit and disconnect spark plug before performing any of the

recommended remedies below other than remedies that require operation of the unit.

-- 1 0 --

LIMITED WARRANTY

ELECTROLUX HOME PRODUCTS, INC.,

warrants to the original purchaser that each

new Weed Eaterrbrand gasoline tool or at-

tachment is free from defects in material and

workmanship and agrees to repair or replace

under this warranty any defective gasoline

product or attachment as follows from the

original date of purchase:

2 YEARS -- Parts and Labor, when used for

household purposes.

90 DAYS -- Parts and Labor, when used for

commercial, professional, or income producing

purposes.

30 DAYS -- Parts and Labor, if used for rental

purposes.

This warranty is not transferable and does not

cover damage or liability caused by improper

handling, improper maintenance, or the use of

accessories and/or attachments not specifically

recommended by ELECTROLUX HOME

PRODUCTS, INC., for this tool. Additionally,

this warranty does not cover tune-ups, spark

plugs, filters, starter ropes, starter springs, cut-

ting line, or rotating head parts that will wear and

require replacement with reasonable use during

the warranty period. This warranty does not

cover predelivery setup or normal adjustments

explained in the instruction manual.

THIS WARRANTY GIVES YOU SPECIFIC

LEGAL RIGHTS, AND YOU MAY HAVE

OTHER RIGHTS WHICH VARY FROM

STATE TO STATE.

NO CLAIMS FOR CONSEQUENTIAL OR

OTHER DAMAGES WILL BE ALLOWED,

AND THERE ARE NO OTHER EXPRESS

WARRANTIES EXCEPT THOSE EX-

PRESSLY STIPULATED HEREIN.

SOME STATES DO NOT ALLOW LIMITA-

TIONS ON HOW LONG AN IMPLIED WAR-

RANTY LASTS OR THE EXCLUSION OR

LIMITATIONS OF INCIDENTAL OR CONSE-

QUENTIAL DAMAGES, SO THE ABOVE

LIMITATIONS OR EXCLUSION MAY NOT

APPLY TO YOU.

The policy of ELECTROLUX HOME PROD-

UCTS, INC., is to continuously improve its prod-

ucts. Therefore, ELECTROLUX HOME

PRODUCTS, INC., reserves the right to

change, modify, or discontinue models, de-

signs, specifications, and accessories of all

products at any time without notice or obligation

to any purchaser.

U.S. EPA

EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGA-

TIONS: The U. S. Environmental Protection

Agency and ELECTROLUX HOME PROD-

UCTS, INC., are pleased to explain the emis-

sions control system warranty on your year

2002--2004 small off--road engine. ELECTRO-

LUX HOME PRODUCTS, INC., must warrant

the emission control system on your small off--

road engine for the periods of time listed below

provided there has been no abuse, neglect, or

improper maintenance of your small off--road

engine. Your emission control system includes

parts such as the carburetor and the ignition

system. Where a warrantable condition exists,

ELECTROLUX HOME PRODUCTS, INC., will

repair your small off--road engine at no cost to

you. Expenses covered under warranty include

diagnosis, parts and labor. MANUFACTUR-

ER’S WARRANTY COVERAGE: If any emis-

sions related part on your engine (as listed un-

der Emissions Control Warranty Parts List) is

defective or a defect in the materials or work-

manship of the engine causes the failure of such

an emission related part, the part will be repaired

or replaced by ELECTROLUX HOME PROD-

UCTS, INC. OWNER’S WARRANTY RE-

SPONSIBILITIES: As the small off--road en-

gine owner, you are responsible for the perfor-

mance of the required maintenance listed in

your instruction manual. ELECTROLUX HOME

PRODUCTS, INC., recommends that you re-

tain all receipts covering maintenance on your

small off--road engine, but ELECTROLUX

HOME PRODUCTS, INC., cannot deny war-

ranty solely for the lack of receipts or for your

failure to ensure the performance of all sched-

uled maintenance. As the small off--road en-

gine owner, you should be aware that ELEC-

TROLUX HOME PRODUCTS, INC., may deny

you warranty coverage if your small off--road

engine or a part of it has failed due to abuse, ne-

glect, improper maintenance, unapproved mod-

ifications, or the use of parts not made or ap-

proved by the original equipment manufacturer.

You are responsible for presenting your small

off--road engine to an ELECTROLUX HOME

PRODUCTS, INC., authorized repair center as

soon as a problem exists. Warranty repairs

should be completed in a reasonable amount of

time, not to exceed 30 days. If you have any

questions regarding your warranty rights and re-

sponsibilities, you should contact your nearest

authorized service center or call ELECTRO-

LUX HOME PRODUCTS, INC., at

1--800--554--6723. WARRANTY COM-

MENCEMENT DATE: The warranty period be-

gins on the date the small off--road engine is

purchased. LENGTH OF COVERAGE: This

warranty shall be for a period of two years from

the initial date of purchase. WHAT IS COV-

ERED: REPAIR OR REPLACEMENT OF

PARTS. Repair or replacement of any war-

ranted part will be performed at no charge to the

owner at an approved ELECTROLUX HOME

PRODUCTS, INC., servicing center. If you

have any questions regarding your warranty

rights and responsibilities, you should contact

your nearest authorized service center or call

ELECTROLUX HOME PRODUCTS, INC., at

1--800--554--6723. WARRANTY PERIOD:

Any warranted part which is not scheduled for

replacement as required maintenance, or which

-- 11 --

is scheduled only for regular inspection to the ef-

fect of “repair or replace as necessary” shall be

warranted for 2 years. Any warranted part which

is scheduled for replacement as required main-

tenance shall be warranted for the period of time

up to the first scheduled replacement point for

that part. DIAGNOSIS: The owner shall not be

charged for diagnostic labor which leads to the

determination that a warranted part is defective

if the diagnostic work is performed at an ap-

proved ELECTROLUX HOME PRODUCTS,

INC., servicing center. CONSEQUENTIAL

DAMAGES: ELECTROLUX HOME PROD-

UCTS, INC., may be liable for damages to other

engine components caused by the failure of a

warranted part still under warranty. WHAT IS

NOT COVERED: All failures caused by abuse,

neglect, or improper maintenance are not cov-

ered. ADD--ON OR MODIFIED PARTS: The

use of add--on or modified parts can be grounds

for disallowing a warranty claim. ELECTRO-

LUX HOME PRODUCTS, INC., is not liable to

cover failures of warranted parts caused by the

use of add--on or modified parts. HOW TO FILE

ACLAIM:If you have any questions regarding

your warranty rights and responsibilities, you

should contact your nearest authorized service

center or call ELECTROLUX HOME PROD-

UCTS, INC., at 1--800--554--6723. WHERE TO

GET WARRANTY SERVICE: Warranty ser-

vices or repairs shall be provided at all ELEC-

TROLUX HOME PRODUCTS, INC., service

centers. Call 1--800--554--6723. MAINTE-

NANCE, REPLACEMENT AND REPAIR OF

EMISSION RELATED PARTS: Any ELEC-

TROLUX HOME PRODUCTS, INC., approved

replacement part used in the performance of

any warranty maintenance or repair on emis-

sion related parts will be provided without

charge to the owner if the part is under warranty.

EMISSION CONTROL WARRANTY PARTS

LIST: Carburetor, Ignition System: Spark Plug

(covered up to maintenance schedule), Ignition

Module. MAINTENANCE STATEMENT: The

owner is responsible for the performance of all

required maintenance as defined in the instruc-

tion manual.

This engine is certified to be emissions compliant for the following use:

Moderate (50 hours)

Intermediate (125 hours)

Extended (300 hours)