Weider 831150290 User Manual PRO 220 Manuals And Guides L0312122
WEIDER Weight System Manual L0312122 WEIDER Weight System Owner's Manual, WEIDER Weight System installation guides
User Manual: Weider 831150290 831150290 WEIDER WEIDER PRO 220 - Manuals and Guides View the owners manual for your WEIDER WEIDER PRO 220 #831150290. Home:Fitness Equipment Parts:Weider Parts:Weider WEIDER PRO 220 Manual
Open the PDF directly: View PDF 
.
Page Count: 16
| Download | |
| Open PDF In Browser | View PDF |
® Model No. 831.150290 Serial No. Write the serial number in the space above for reference. WEIGHT BENCH EXERCISER User's Manual Serial Number Decal (under seat) • Assembly • Adjustments • Troubleshooting • Part List and Drawing Patent Pending _CAUTION Read all precautions and instructions in this manuel before using this equipment. Save this manual for future reference. Sears, Roebuck and Co., Hoffman Estates, IL 60179 TABLE OF CONTENTS WARNING DECAL PLACEMENT ........................................................... IMPORTANT PRECAUTIONS .............................................................. BEFORE YOU BEGIN ................................................................... PART IDENTIFICATION CHART ............................................................ ASSEMBLY ........................................................................... ADJUSTMENTS ....................................................................... EXERCISE GUIDELINES ................................................................ PART LIST ........................................................................... EXPLODED DRAWING ................................................................. ORDERING REPLACEMENT PARTS ................................................ WARRANTY ................................................................... WARNING 2 3 4 5 6 10 11 14 15 Back Cover Back Cover DECAL PLACEMENT The warning decals shown here have been placed on the weight bench in the locations shown. If a decal is missing or illegible, please call toll-free 1-800-999-3756, Mon. through Fri., 6 a.m. until 6 p.m. Mountain Time, to order a free replacement decal. Place the decal on the weight bench in the location shown. Misuse of this )roduct may result in serious injury. Read user's manual andfollow allwarnings and operatinginstructions prior to use. ) hands ngers clear of • Do not allow children on or aroundmachine. • Replace label if damaged, illegible, or removed. 2 IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read the following important precau- tions before using the weight bench. 1. Read all instructions in this manual before using the weight bench. Use the weight bench only as described in this manual. 2. It is the responsibility of the owner to ensure that all users of the weight bench are adequately informed of all precautions. 3. The weight bench is intended for home use only. Do not use the weight bench in any commercial, rental, or institutional setting. 4. Use the weight bench only on a level surface. Cover the floor beneath the weight bench to protect the floor. 5. 6. Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediately. 10. The weight bench is designed to support a maximum user weight of 300 pounds, and a maximum total weight of 410 pounds. Do not place more than t10 pounds, including a barbell and weights, on the weight rests. Do not place more than 50 pounds on the leg lever. 11. Always be sure there is an equal amount of weight on each side of your barbell when you are using it. Always keep some weight on both ends of the barbell when adding or removing weights to prevent the barbell from tipping. 12. When you are using the leg lever, place a barbell with the same amount of weight on the weight rests to balance the bench. 13. Always exercise with a partner. When you are performing bench press exercises, your partner should stand behind you to catch the barbell if you cannot complete a repetition. Keep children under 12 and pets away from the weight bench at all times. 8. Keep hands and feet away from moving parts. 14. When using the backrest in an inclined position, make sure that the support rod is inserted completely through both uprights, and that the support rod is turned to the locked position. 9. Do not use a barbell that is longer than six feet with the weight bench, Note: The weight bench does not include a barbell or weights, 15. If you feel pain or dizziness at any time while exercising, stop immediately and begin cooling down. Always wear athletic shoes for foot protection while exercising. 7. WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. Bears assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 3 BEFORE YOU BEGIN Thank you for selecting the versatile WELDER®PRO 220 weight bench. The weight bench offers an impressive array of weight stations designed to develop every major muscle group of the body. Whether your goal is to tone your body, build dramatic muscle size and strength, or improve your cardiovascular system, the weight bench will help you to achieve the specific results you want. For your benefit, read this manual carefully before using the weight bench, If you have questions after ASSEMBLED DIMENSIONS: Height: 47 in. Width: 30 in. Depth: 62 in. reading this manual, call 1-800-4-MY-HOME ® (1-800-4694663). To help us assist you, please note the product model number and serial number before calling. The model number is 831.150290. The serial number can be found on a decal attached to the weight bench (see the front cover of this manual for the location of the decal). Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. ! _Weight Rests Z Suppo_ Rod Seat Leg Lever-- 4 PART IDENTIFICATION CHART This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below each part refers to the key number of the part, from the PART LIST on page 14 of this manual. Important: Some parts may have been pre-assembled for shipping purposes. If you cannot find a part in the parts bags, check to see if it has been pre÷assembled. If a part is missing, call toll-free 1-800-999-3756. 50mm Square Inner Cap (16) 25mm Round Angle Cap (17) M4 x 16mm Screw (29) 25mm Round Inner Cap (20) Inner Cap (18) M6 x 16ram Screw (24) 38mm Square 19mm Round Inner Cap (21) M10 x 50mm Bolt (28) ( M10 x 60mm Bolt (25) 25mm Square Inner Cap (19) r M10 Washer (30) M6 Washer (22) ( M 10 x 60mm Carriage Bolt (26) ( M10 Nylon Locknut (31) M10 x 68ram Bolt (27) M10 x 142mm Bolt (23) 5 ASSEMBLY Make Things Easier for Yourself Everything in this manual is designed to ensure that the weight bench can be assembled successfullyby anyone. However, it is importantto realize that the versatile weight bench has many parts and that the assembly process will take time. Most people find that by setting aside plenty of time, assembly will go smoothly. • As you assemble the weight bench, make sure all parts are oriented as shown in the drawings. • For help identifying small parts, use the IPENTIFICATION CHART on page 5, The following tools (not included) are required for assembly: • Two adjustable wrenches • One rubber mallet Before beginning assembly, carefully read the following information and instructions: • One standard screwdriver • Assembly requires two people. • One Phillips screwdriver • Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials untilassembly is completed. • Lubricant, such as grease and soapy water. jelly, Assembly will be more convenient if you have a socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches. • Tighten all parts as you assemble them, unless instructedto do otherwise. 1. or petroleum Before assembling the weight bench, be sure that you have read and understand the information in the box above. 16 Press three 50mm Square Inner Caps (16) into the Upright (1) without the warning decal. Attach two Joint Plates (11) to the Upright (1) with two M10 x 68mm Bolts (27) and two M10 Nylon Locknuts (31). Do not tighten the Locknuts yet. Warning Decal Repeat this step with the other Upright (1). Make sure the Joint Plates (11) are oriented as shown in the inset drawing. 11 ,31 11 16 6 2. Attach the Crossbar (2) to an Upright (1) with two !2 M10 x 68mm Bolts (27), two Joint Plates (11), and two M10 Nylon Locknuts (31). Do not tighten the Locknute yet. Repeat this step with the other Upright (1). 11 27 3. 2 Press three 50ram Square Inner Caps (16) into the Front Leg (4) and the Stabilizer (5). Attach the Front Leg (4) to the Stabilizer (5) with two M10 x 60mm Carriage Bolts (26) and two M10 Nylon Locknuts (31). Do not tighten the Locknuts yet. 4 31 16 _.. "% 31 o 16 26l 4. Attach the Front Leg (4) to the Bench Frame (3) with two M10 x 50mm Bolts (28), two M10 Washers (30), and two M10 Nylon Locknuts (31). Do not tighten the Locknuts yet. Make sure the bolt heads fit inside the hexagon holes in the Bench Frame. 4 31 3O 3 30 Hexagon Holes AttachtheBenchFrame (3) to the Crossbar (2) with two M10 x 68mm Bolts (27) end two M10 Nylon Locknuts (31). 2 Tighten the M10 Nylon Locknuts (31) used in steps 1-5. 27 3 31 6. Press a 25mm Round Inner Cap (20) into the indicated end of the weight tube on the Leg Lever (6). Press a 25mm Round Angled Cap (17) onto the other end of the weight tube. S 6 31 Tap two 38mm Square Inner Caps (18) into the Leg Lever (6). 18-..._o_°'°_ Lubricate the M10 x 60mm Bolt (25) with grease. Attach the Leg Lever (6) to the Front Leg (4) with the Bolt and an M10 Nylon Locknut (31). Do not overtighten the Locknut; the Leg Lever must be able to pivot easily. Lubricate 18 7. Press two 25mm Square Inner Caps (19) into a Pad Tube (12). Slide the Pad Tube into the Leg Lever (6). Slide two Foam Pads (13) onto the ends of the Pad Tube. Make sure the Foam Pads are oriented as shown. _. 13 6 19,_"_ Repeat this step with the other Pad Tube (12). / 12 8, Press a 25mm Round Inner Cap (20) into a Weight Rest (15). Insert the Weight Rest intoan Upright (1). Turn the Weight Rest so the locking pin is wrapped around the Updght, 8 Repeat this step with the other Weight Rest (15). Pin 20 15 8 _ 1 9. Press two 19mm Round Inner Cap (21) into the Support Rod (14). Insert the Support Rod into a set of holes in the Uprights (1). Turn the Support Rod so the locking pin is wrapped around the Upright. 9 14 21 Locking Pin 21 10. Press four 25mm Square two Backrest Tubes (7). Inner Caps (19) into the 10 8 Attach the Backrest Tubes (7) to the Backrest (8) with four M6 x 38mm Screws (32) and four M6 Washers (22). Do not tighten the Screws yet. 22 7 32 19 _,22 32 11. Lubricate an M10 x 142mm Bolt (23) with grease. Attach the Backrest Tubes (7) to the welded tube on the Bench Frame (3) with the Bolt, two M10 Washers (30), and an M10 Nylon Locknut (31). Do not overtighten the Locknut; the Backrest Tubes must be able to pivot easily. 11 30 Tighten the M6 x 38ram Screws (32) used in step 10. Tube 12. Attach the Seat (9) to the Bench Frame (3) with four M6 x 16ram Screws (24). 12 13. Make sure that all parts are properly tightened before you use the weight bench, The use of all remaining parts will be explained in ADJUSTMENTS, beginning on the following page. 24 9 ADJUSTMENTS The weight bench is designed to be used with your own weight set (not included).The steps below explain how the weight bench can be adjusted. See EXERCISE GUIDELINES on page 11 for important exercise information and refer to the accompanying exercise guide to see the correct form for each exercise. Refer also to the exercise information accompanying your weight set for additional exercises. Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediately. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents. ADJUSTING THE BACKREST The Backrest (8) can be used in a decline position, a level position, or two incline positions. To use the Backrest in the decline position, remove the Support Rod (14) and lay the Backrest on the Crossbar (2). To use the Backrest (8) in the level position,lift the Backrest and insert the Support Rod (14) through the bottom set of holes in the Uprights (1). Rotate the locking pin into place around the Upright. To use the Backrest (8) in an incline position, lift the Backrest and insert the Support Rod (14) through an upper set of holes in the Uprights (1). Rotate the locking pin into place around the Upright. WARNING: When using the Backrest (8) in a level or incline position, insert the Support Rod (14) completely through both Uprights (1) and turn it to the locked position. 6 ATTACHING WEIGHTS TO THE LEG LEVER To use the Leg Lever (6), slide the desired weights (not included) onto the weight tube. Weight WARNING: Do not place more than 60pounds onthe Leg Lever (6). Weight ADJUSTING THE WEIGHT RESTS To change the weight of the Weight Rests (15), remove the them from the Uprights(1) and insert them into the desired set of holes. Rotate the Weight Rests so that the lockingpinswrap around the Uprights. Lo_k_ng 15 WARNING: Al*sye setboth Weight Rests (15) atthe same height. 10 EXERCISE GUIDELINES THE FOUR BASIC TYPES OF WORKOUTS PERSONALIZING Muscle Building To increase the size and strength of your muscles, push them close to their maximum capacity.Your muscles will continuallyadapt and grow as you progressively increase the intensity of your exercise. You can adjust the intensity level of an individualexercise in two ways: • by changing the amount of resistance used • by changing the number of repetitionsor sets performed. (A "repetition" is one complete cycle of an exercise, such as one sit-up. A =set" is a series of repetitions.) Determining the exact length of time for each workout, as well as the number of repetitions or sets completed, is an individual matter. It is important to avoid overdoing it during the first few months of your exercise program. You should progress at your own pace and be sensitive to your body's signals. If you experience pain or dizziness at any time while exercising, stop immediately and begin cooling down. Find out what is wrong before continuing. Remember that adequate rest and a proper diet are important factors in any exercise program. YOUR EXERCISE PROGRAM WARMING UP The proper amount of resistancefor each exercise depends upon the individual user. You must gauge your limits and select the amount of resistancethat is right for you. Begin with 3 sets of 8 repetitions for each exercise you perform. Rest for 3 minutesafter each set. When you can complete 3 sets of 12 repetitions without difficulty,increase the amount of resistance. Begin each workoutwith 5 to 10 minutes of stretching and light exercise to warm up. Warming up prepares your body for more strenuous exercise by increasing circulation,raising your body temperature and delivering more oxygen to your muscles. WORKING Toning You can tone your muscles by pushing them to a moderate percentage of their capacity.Select a moderate amount of resistance and increase the number of repetitions in each set. Complete as many sets of 15 to 20 repetitions as possible withoutdiscomfort. Rest for 1 minute after each set. Work your muscles by completing more sets rather than by using high amounts of resistance. Weight Loss To lose weight, use a tow amount of resistance and increase the number of repetitions in each set. Exercise for 20 to 30 minutes, resting for a maximum of 30 seconds between sets. Cross Training Cress training is an efficientway to get a complete and well-balanced fitness program. An example of a balanced program is: • Plan strength training workouts on Monday, Wednesday, and Friday. • Plan 20 to 30 minutes of aerobic exercise, such as runningon a treadmill or ridingon an exercise bike, on Tuesday and Thursday. • Rest from both strength training and aerobic exercise for at least one full day each week to give your body time to regenerate. The combination of strengthtraining and aerobic exercise will reshape and strengthenyour body, plusdevelop your heart and lungs. OUT Each workout should include 6 to 10 different exercises. Select exercises for every major muscle group, emphasizing areas that you want to develop most. To give balance and variety to your workouts, vary the exercises from session to session. Schedule your workoutsfor the time of day when your energy level is the highest. Each workout should be followed by at least one day of rest. Once you find the schedule that is right for you, stickwith it. EXERCISE FORM Maintaining proper form is an essential part of an effective exercise program. This requires moving through the full range of motion for each exercise, and moving onlythe appropriate parts of the body. Exercising in an uncontrolledmanner will leave you feeling exhausted. On the exercise guide accompanying this manual you will find photographsshowingthe correct form for several exercises, and a list of the muscles affected. Refer to the muscle chart on the next page to find the names of the muscles. The repetitions in each set should be performed smoothly and without pausing. The exertion stage of each repetition should last about half as long as the return stage. Proper breathing is important. Exhale during the exertion stage of each repetition and inhale during the return stroke. Never hold your breath. 11 Rest for e short pedod of time after each set. The ideal resting periods are: • Rest for three minutes after each set for a muscle building workout. • Rest for one minute after each set for a toning workout. • Rest for 30 seconds after each set for a weight loss workout. Plan to spend the first couple of weeks familiarizing yourself with the equipment and learning the proper form for each exercise. COOLING DOWN End each workout with 5 to 10 minutes of stretching. Include stretches for both your arms and legs. Move slowly as you stretch and do not bounce. Ease into each stretch gradually and go only as far as you can without strain. Stretching at the end of each workout is an effective way to increase flexibility. STAYING MOTIVATED For motivation, keep a record of each workout.The chart on page 13 of this manual can be photocopied and used to schedule and record your workouts. List the date, the exercises performed, the resistance used, and the numbers of sets and repetitions completed. Record your weight and key body measurements at the end of every month. Remember, the key to achieving the greatest results is to make exercise a regular and enjoyable part of your everyday life. MUSCLE CHART A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. P. Q. R. S. T. U. V. W. X. 12 Sternomastoid (neck) Pectoralis Major (chest) Biceps (front of arm) Obliques (waist) Brachioradials (forearm) Hip Flexors (upper thigh) Abductor (outer thigh) Quadriceps (front of thigh) Sartorius (frontofthigh) Tibialis Anterior (front of calf) Soleus (front of calf) Anterior Deltoid (shoulder) Rectus Abdominus (stomach) Adductor (inner thigh) Trepezius (upper back) Rhomboideus (upper back) Posterior Deltoid (shoulder) Triceps (back of arm) Latissimus Dorsi (mid back) Spinae Erectors (lower back) Gluteus Medius (hip) Gluteus Maximus (buttocks) Hamstring (back of leg) Gastrocnemius (back of calf) MONDAY EXERCISE WEIGHT SETS REPS WEIGHT SETS REPS WEIGHT SETS REPS Date: / I AEROBIC EXERCISE TUESDAY Date: / / WEDNESDAY Date: / EXERCISE / THURSDAY AEROBIC EXERCISE Date: ! / FRIDAY EXERCISE Date: / / Make photocopies of this page for scheduling and recording your workouts. t3 PART LIST--Model Key No. Qty. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 2 1 1 1 1 1 2 1 1 2 4 2 4 1 2 9 1 2 No. 831.150290 Description R0803A Key No. Qty. 19 20 21 22 23 24 25 26 27 28 29 30 31 32 # # # 8 3 2 4 1 4 1 2 10 2 4 4 16 4 1 1 1 Upright Crossbar Bench Frame Front Leg Stabilizer Leg Lever Backrest Tube Backrest Seat Upright Cover Joint Plate Pad Tube Foam Pad Support Rod Weight Rest 50mm Square Inner Cap 25ram Round Angled Cap 38mm Square Inner Cap Description 25mm Square Inner Cap 25mm Round Inner Cap 19mm Round Inner Cap M6 Washer M10 x 142mm Bolt M6 x 16mm Screw M10 x 6Omm Bolt M1O x 60ram Carriage Bolt M1O x 68mm Bolt M10 x 5Omm Bolt M4 x 16mm Screw M1O Washer M10 Nylon Locknut M6 x 38ram Screw User's Manual Exercise Guide Grease Pack '_" Indicates a non-illustratedpart. Specifications are subject to change without notice. See the back cover of this manual for information on ordering replacement parts. 14 EXPLODED DRAWING--Model No. 831.150290 R0803A 8 32 23 16 32 31 10 29 15 16 27 9 19 16 13 1- 16 13 31 16 31 24 18,._ 24 20 28 31 16 15 Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories, and user's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. !!ili_iii 1-800-4-MY-HOM E® _;ili,!! iii!!i_!i Anytime, day or night (U.S.A. and Canada) www.sears.ca (1-800-469-4663) www.sears.com Our Home For repair of carry-in products like vacuums, lawn equipment, and electronics, call or go on-line for the location of your nearest Sears Parts and Repair Center. 1-800-488-1222 Anytime, day or night (U,S,A, only) www.sears.com To purchase a protection agreement (U.S.A.) or maintenance agreement (Canada) on a product serviced by Sears: 1-800-827-6655 iiiii!iii!_ (u.s.A) 1-800-361-6665 (Canada) Para pedir servicio de reparaci6n a domicilio, y para ordenar piezas: 1-888-SU-HOGAR _ (1-888-784.6427) @ Registered Trademark / TMTrademark / SMService Mark of Sears, Roebuck and Co. ® Marca Registrada / _ Marca de F_bdca / su Mama de Servicio de Sears, Roebuck and Co, WARRANTY For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this WEIGHT BENCH EXERCISER, contact the nearest Sears Service Center throughout the United States and Sears will repair or replace the WEIGHT BENCH EXERCISER, free of charge. This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for rental purposes. This warranty gives you specificlegal rights, and you may also have other rights which vary from state to state. Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179 %. Part No. 199258 R0803A J Printed in China © 2003 Sears, Roebuck and Co.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 16 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Tue Apr 03 05:22:44 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools