Weider 8620 System Wesy8529 Users Manual *WESY85290 156863

Weider-Wesy85290-Owner-S-Manual weider-wesy85290-owner-s-manual

WESY85290 to the manual e35d3c0f-61dc-4684-acae-1cb59c327a30

2015-05-18

: Weider Weider-8620-System-Wesy8529-Users-Manual-734190 weider-8620-system-wesy8529-users-manual-734190 weider pdf

Open the PDF directly: View PDF PDF.
Page Count: 25

USERÕS MANUAL
QUESTIONS?
As a manufacturer, we are com-
mitted to complete customer sat-
isfaction. If you have questions,
or if there are missing/damaged
parts, we will guarantee you com-
plete satisfaction through direct
assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
Visit our website at:
www.weiderfitness.com
Model No. WESY85290
Serial No.
Write the serial number in the space
above for reference.
PATENT PENDING
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Serial Number Decal
2
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
WEIGHT RESISTANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
TROUBLE-SHOOTING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
CABLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING/PART LIST and a PART IDENTIFICATION CHART are attached to the center
of this manual. Remove the EXPLODED DRAWING/PART LIST and the PART IDENTIFICATION CHART before
beginning assembly.
WEIDER is a registered trademark of ICON Health & Fitness, Inc.
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product at one of its authorized service centers. All products for which war-
ranty claim is made must be received by ICON at one of its authorized service centers with all freight and other
transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-autho-
rized by ICON. This warranty does not extend to any product or damage to a product caused by or attribut-
able to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON autho-
rized service center, products used for commercial or rental purposes, or products used as store display mod-
els. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential dam-
ages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential
damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Table of Contents
Limited Warranty
3
1. It is the responsibility of the owner to ensure
that all users of the home gym system are
adequately informed of all precautions.
2. Read all instructions in this manual and in
the accompanying literature before using the
home gym system.
3. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
4. Use the home gym system only on a level
surface. Cover the floor or carpet beneath
the home gym system for protection.
5. Inspect and tighten all parts often. Replace
any worn parts immediately.
6. Keep children under 12 and pets away from
the home gym system at all times.
7. The home gym system is designed to be
used by only one person at a time.
8. Keep hands and feet away from moving parts.
9. Always wear athletic shoes for foot protec-
tion.
10. Always stand on a foot plate when perform-
ing an exercise that could cause the home
gym system to tip.
11. Never release the press arm, butterfly arms,
leg lever, lat bar, leg press plate, or nylon
strap while weights are raised. The weights
will fall with great force.
12. Make sure that the cables remain on the pul-
leys at all times. If the cables bind while you
are exercising, stop immediately and make
sure that the cables are on all of the pulleys.
13. Always disconnect the lat bar from the home
gym system when performing an exercise
that does not use the lat bar.
14. The home gym system is intended for home
use only. Do not use the home gym system
in any commercial, rental, or institutional set-
ting.
WARNING: To reduce the risk of serious injury, read the following important precautions before
using the home gym system.
WARNING: Before beginning this or any exercise program, consult your physician. This is especially
important for persons over the age of 35 or persons with pre-existing health problems. Read all
instructions before using. ICON assumes no responsibility for personal injury or property damage
sustained by or through the use of this product.
Important Precautions
4
ASSEMBLED
DIMENSIONS:
Height: 76 in.
Width: 38 in.
Length: 59 in.
Leg Press Plate
Low Pulley Station
Foot Plate
High Pulley Station
Lat Bar
Leg Lever
Butterfly Arms
Press Arm
Weight Stack
Seat
Backrest
Weight Pin
Lat Bar Holder
Thank you for selecting the versatile WEIDER¨8620
Home Gym System. The WEIDER¨8620 offers a
selection of weight stations designed to develop every
major muscle group of the body. Whether your goal is
to tone your body, build dramatic muscle size and
strength, or improve your cardiovascular system, the
WEIDER¨8620 will help you to achieve the specific
results you want.
For your benefit, read this manual carefully before
using the WEIDER¨8620 Home Gym System. If you
have additional questions, please call our Customer
Service Department toll-free at 1-800-999-3756,
Monday through Friday, 6 a.m. until 6 p.m. Mountain
Time (excluding holidays). To help us assist you,
please note the product model number and serial
number before calling. The model number is
WESY85290. The serial number can be found on a
decal attached to the WEIDER¨8620 (see the front
cover of this manual).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
Before You Begin
5
1
56
High Side of
Bracket
3
5
51
51 14
1
4
1
Before beginning assembly, carefully read the
following information and instructions:
¥Place all parts of the home gym system in a
cleared area and remove the packing materials;
do not dispose of the packing materials until
assembly is completed.
¥ The assembly is divided into four stages: 1)
frame assembly, 2) press and butterfly arm
assembly, 3) cable and pulley assembly, and 4)
seat and backrest assembly. The hardware for
each stage is packaged separately.
¥ Wait until you begin each assembly stage to open
that parts bag.
¥For help identifying the small parts used in
assembly, use the PART IDENTIFICATION
CHART located in the center of this manual.
Note: Some small parts may have been pre-
attached for shipping. If a part is not in the parts
bag, check to see if it has been pre-attached.
¥As you assemble the home gym system, be sure
that all parts are oriented as shown in the
drawings.
¥Tighten all parts as you assemble them, unless
instructed to do otherwise.
THE FOLLOWING TOOLS (NOT INCLUDED) ARE
REQUIRED FOR ASSEMBLY:
¥ Two (2) adjustable wrenches
¥ One (1) standard screwdriver
¥ One (1) phillips screwdriver
¥ One (1) rubber mallet
¥ Lubricant, such as grease or petroleum jelly,
and soapy water will also be needed.
Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches, or a set of ratchet wrenches.
1. Before beginning assembly, be sure that
you have read and understand the infor-
mation in the box above.
Press a 2Ó Square Outer Cap (51) onto each
end of the Stabilizer (5). Press a 2Ó Square
Inner Cap (27) into the end of the Base (4).
Insert two 5/16Ó x 2 3/4Ó Carriage Bolts (14)
up through the Stabilizer (5). Insert four
5/16Ó x 2 1/2Ó Carriage Bolts (1) up through
the Base (4).
Slide the indicated end of the Base (4) onto
the 5/16Ó x 2 3/4Ó Carriage Bolts (14) in the
Stabilizer (5). Slide the Rear Upright (56)
onto the Carriage Bolts. Hand tighten a 5/16Ó
Nylon Locknut (3) onto each Carriage Bolt.
The high side of the bracket on the Rear
Upright must be on the side shown. Do
not tighten the Nylon Locknuts yet.
FRAME ASSEMBLY
27
Assembly
6
FRAME ASSEMBLY
2. Slide the Front Upright (42) onto the 5/16Ó x
2 1/2Ó Carriage Bolts (1) in the Base (4).
Hand tighten a 5/16Ó Nylon Locknut (3) onto
each Carriage Bolt. Do not tighten the
Nylon Locknuts yet.
3. Press a 2Ó Square Inner Cap (27) into the
open end of the Top Frame (55). Press a 1
3/4Ó Square Inner Cap (44) into each end of
the crossbar on the Top Frame. Press two 1Ó
Round Inner Caps (49) into the top of the
crossbar.
Attach the Top Frame (55) to the Front Upright
(42) and the Rear Upright (56) with four 5/16Ó
x 2 3/4Ó Bolts (11), four 5/16Ó Flat Washers
(8), and four 5/16Ó Nylon Locknuts (3).
Tighten all Nylon Locknuts used in steps 1
through 3.
4. Set two Weight Bumpers (19) onto the brack-
et on the Base (4) as shown.
Stack eight Weights (25) on the Weight
Bumpers (19). Be sure that all of the Weights
are turned so the pin grooves are on the
same side.
4
2
3
42
3
1
4
11 11
49
8
44
44
27
55
56 42
3
Crossbar
25
Pin Groove
19
4ÑBracket
3
8
7
FRAME ASSEMBLYARM ASSEMBLY
5. Press the Weight Tube Bumper (64) into the
end of the Weight Tube (63). Insert the
Weight Tube into the stack of Weights (25).
Be sure that the pins on the Weight Tube are
resting in the pin grooves in the upper
Weight.
Lubricate the insides of the holes in the Top
Weight (76). Set the Top Weight onto the
stack of Weights (25).
Insert both Weight Guides (62) into the stack
of Weights (25). Be sure that the holes in
the Weight Guides are at the top, as
shown.
6. Attach the upper ends of the Weight Guides
(62) to the Top Frame (55) with the 5/16Ó x 6Ó
Bolt (60), two 1/2Ó x 3/4Ó Spacers (61), and a
5/16Ó Nylon Locknut (3).
Be sure that the Pulley Bracket (20) is in
front of the Weight Guide (62) as shown.
7. Press a 1Ó x 7/8Ó Plastic Bushing (75) onto
each welded spacer on the Press Frame (17).
Slide the Press Frame into place on the Base
(4). Note: This will be a tight fit. The
Plastic Bushings should fit onto each end
of the indicated tube in the Base. Be sure
that the pulley is on the indicated side.
Lubricate the 3/8Ó x 8Ó Bolt (59). Attach the
Press Frame (17) to the Base (4) with the
3/8Ó x 8Ó Bolt and a 3/8Ó Nylon Locknut (21).
7
5
6
55
76
63
64
25
62
Lubricate
Pins
60 20
62
3
4ÑTube
Welded
Spacers
17 Lubricate
59
Pulley
21
75
61
Holes
8
ARM ASSEMBLY
8. Press a 1 3/4Ó Square Inner Cap (44) into the
top of a Press Arm (46). Wet the handle on
the Press Arm with soapy water. Slide a
Handgrip (31) onto the handle. Press a 1Ó
Round Inner Cap (49) into the other end of
the handle. Attach the Press Arm to one side
of the Press Frame (17) with two 5/16Ó x 2 1/2Ó
Bolts (22) and two 5/16Ó Nylon Locknuts (3).
Assemble the other Press Arm (46) in the
same manner.
9. Identify the Right Arm (48) and the Left Arm
(47). Note the position of the welded bracket
on each Arm. Arm identification is very
important for step 10.
Attach a ÒVÓ-Pulley (6) and a Long Cable Trap
(50) to the Right Arm (48) with a 3/8Ó x 2 1/2Ó
Bolt (7) and a 3/8Ó Nylon Locknut (21).
Attach a ÒVÓ-Pulley (6) and a Long Cable Trap
(50) to the Left Arm (47) with a 3/8Ó x 2 1/2Ó
Bolt (7) and a 3/8Ó Nylon Locknut (21).
10. Lubricate both axles on the Top Frame (55).
Slide the Right Arm (48) onto the right axle.
Note: Be careful not to confuse the Right
Arm with the Left Arm (47); refer to step 9
to identify the Right Arm. Be sure that the
upper end of the Right Arm is behind the
indicated bracket on the Top Frame (55).
Tap two 1Ó Retainers (69) and a 1Ó Round
Cover Cap (70) onto the right axle. Be sure
that the teeth on the Retainers bend
toward the Cover Cap, as shown in the
inset drawing.
Attach the Left Arm (47) in the same manner.
Press 1 3/4Ó Square Inner Caps (44) into the
lower ends of the Right and Left Arms (47,
48). Wet the lower end of each Arm with
soapy water. Slide a 10Ó Pad (45) onto the
lower end of each Arm.
10
50
50
46
3
22
46
49
44
17
44
49
31
Bracket
Lubricate Axle
45
47
55
48
45
44
69
70
6
48
47
Welded
Brackets
21
8
9
69
55
70
76
11. Press a 1 3/4Ó Square Inner Cap (44) into the
Seat Frame (36). Attach a Bumper (73) to the
Seat Frame with a 1/2Ó Tap Screw (65).
Slide the Seat Frame (36) onto the 5/16Ó x
2 1/2Ó Carriage Bolts (1) in the Base (4). See
the inset drawing. The bracket on the Seat
Frame must be behind the Press Frame
(17). Hand-tighten a 5/16Ó Nylon Locknut (3)
onto each Carriage Bolt. Do not tighten the
Nylon Locknuts until the end of this
assembly step.
Attach the Seat Frame (36) to the Front
Upright (42) with two 5/16Ó x 2 3/4Ó Bolts (11),
two 5/16Ó Flat Washers (8), and two 5/16Ó
Nylon Locknuts (3).
Tighten all Nylon Locknuts used in this
step now.
12. Attach a Bumper (73) to the Rocker Arm (32)
with a 1/2Ó Tap Screw (65).
Lubricate a 3/8Ó x 3 1/4Ó Bolt (35). Attach the
Rocker arm (32) to the Base (4) with the 3/8Ó
x 3 1/4Ó Bolt and a 3/8Ó Nylon Locknut (21).
13. Lubricate a 3/8Ó x 2 1/2Ó Bolt (7). Attach the
Leg Lever (29) to the Rocker Arm (32) with
the 3/8Ó x 2 1/2Ó Bolt and a 3/8Ó Nylon Jam
Nut (33).
Press a 1 3/4Ó Square Inner Cap (44) into
each end of the Leg Lever (29).
13
11
8
12
9
ARM ASSEMBLY
Bracket
17
36
1
44
36
3
3
42
73
32
73
65
4
21
7ÑLubricate
29
32
44
44
LubricateÑ35
65
4
11
33
14. During steps 15 through 29, refer to the
CABLE DIAGRAM on page 19 of this manual
to verify proper cable routing. Before begin-
ning this section, identify the Long Cable (23)
and the Short Cable (58) by comparing the
lengths of the cables.
IMPORTANT: While assembling the cables,
do not overtighten the bolts and nuts
securing the pulleys. The pulleys must be
able to turn freely.
15. Locate the Long Cable (23). Route the Long
Cable around the indicated 3 1/2Ó Pulley (15)
attached to the Top Frame (55). Be sure that
the end of the Cable with the ball is on the
indicated side of the Pulley and that the
Cable is between the Pulley and the hook.
Tighten the 3/8Ó x 3 3/4Ó Bolt (71) and the 3/8Ó
Nylon Locknut (not shown).
16. Wrap the Long Cable (23) around a ÒVÓ-Pulley
(6). Attach the ÒVÓ-Pulley and a Long Cable
Trap (50) to the indicated bracket on the
Front Upright (42) with a 3/8Ó x 2 1/2Ó Bolt (7)
and a 3/8Ó Nylon Locknut (21). Be sure that
the Long Cable Trap is positioned to hold
the Cable in place.
17. Route the Long Cable (23) around the ÒVÓ-
Pulley (6) on the Left Arm (47). Be sure that
the Cable is in the groove of the Pulley
and that the Long Cable Trap (50) is posi-
tioned to hold the Cable in place. Tighten
the 3/8Ó x 2 1/2Ó Bolt (7) and the 3/8Ó Nylon
Locknut (not shown).
17
14
15
16
58
23
55
71
Hook
Ball
15
50
23
7
47
23
7
21
650
23
6
42
CABLE ASSEMBLY
10
11
18. Route the Long Cable (23) around the ÒVÓ-
Pulley (6) on the Right Arm (48). Be sure
that the Cable is in the groove of the ÒVÓ-
Pulley and that the Long Cable Trap (50) is
turned to hold the Cable in place. Tighten
the 3/8Ó x 2 1/2Ó Bolt (7) and the 3/8Ó Nylon
Locknut (not shown).
19. Route the Long Cable (23) around the 3 1/2Ó
Pulley (15) attached to the Pulley Bracket
(20). Be sure that the Cable is in the
groove of the Pulley and that the Cable
Trap (66) is turned to hold the Cable in
place. Tighten the 3/8Ó x 2Ó Bolt (12) and the
3/8Ó Nylon Locknut (not shown).
Be sure that the 5/16Ó x 5Ó Bolt (68) is proper-
ly tightened and that the Pulley Bracket (20)
can move freely.
20. See the inset drawing. Attach a 3 1/2Ó Pulley
(15) and a Cable Trap (66) to the indicated
hole in the Long ÒUÓ-Bracket (57) with a 3/8Ó x
2Ó Bolt (12) and a 3/8Ó Nylon Locknut (21). Be
sure that the Cable Trap is inside the ÒUÓ-
Bracket. Note: This may come pre-assem-
bled.
Route the Long Cable (23) around the 3 1/2Ó
Pulley (15) and through the Long ÒUÓ-Bracket
(57). Be sure that the Cable is in the
groove of the Pulley and that the Cable
and Pulley move smoothly.
21. Note: The 3 1/2Ó Pulley (15) labeled in this
step is pre-attached. It is shown removed
for easy part identification.
Route the Long Cable (23) around the 3 1/2Ó
Pulley (15) attached to the bracket on the Top
Frame (55). Tighten the 3/8Ó x 2Ó Bolt (12)
and the 3/8Ó Nylon Locknut (21). Be sure that
the Cable is in the groove of the Pulley
and that the Cable and Pulley move
smoothly.
21
18
19
20
CABLE ASSEMBLY
48
50 76
23
66
15
12
20
68
23
21
12
15
23
57
66
12
15
23
Bracket
55
21
23
12
22. Locate the Short Cable (58). Route the
Short Cable under the 3 1/2Ó Low Pulley (77).
Be sure that the end of the Cable with the
ball is on the indicated side of the Pulley
and that the Cable is between the Pulley
and the welded spacer on the Leg Lever
(29). Tighten the 3/8Ó x 3 1/2Ó Bolt (16) and
the 3/8Ó Nylon Locknut (not shown).
23. Wrap the Short Cable (58) around a ÒVÓ-
Pulley (6). Attach the Pulley and a Long
Cable Trap (50) inside the bracket on the
Seat Frame (36) with a 3/8Ó x 2 1/2Ó Bolt (7)
and a 3/8Ó Nylon Locknut (21). Be sure that
the Cable Trap is turned to hold the Cable
in place and that the Cable is routed
around the Pulley as shown.
24. Wrap the Short Cable (58) around a 3 1/2Ó
Pulley (15). Attach the Pulley to the Rocker
Arm (32) with a 3/8Ó x 3 1/2Ó Bolt (16), a 3/8Ó
Flat Washer (9), and a 3/8Ó Nylon Locknut
(21). Be sure that the Cable Trap (66) is
turned to hold the Cable in place and that
the Cable is routed around the Pulley as
shown.
25. Note: The 3 1/2Ó Pulley (15) labeled in this
step is pre-attached. It is shown removed
for easy part identification.
Route the Short Cable (58) around the 3 1/2Ó
Pulley (15) attached to the lower hole in the
Front Upright (42). Be sure that the Cable
Trap (66) is turned to hold the Cable in
place and that the Cable is routed around
the Pulley as shown. Tighten the 3/8Ó Nylon
Locknut (21) and the 3/8Ó x 3 3/4Ó Bolt (71).
25
22
23
24
CABLE ASSEMBLY
58 77 Ball
16
58
621
16
66
15
32
9
21
29
7
50
36
58
42
21
71
58
9
66
15
Welded Spacer
13
26. Note: The 3 1/2Ó Pulley (15) labeled in this
step is pre-attached. It is shown removed
for easy part identification.
Route the Short Cable (58) around the 3 1/2Ó
Pulley (15) attached to the upper hole in the
Press Frame (17). Be sure that the Cable is
routed around the Pulley as shown.
Tighten the 3/8Ó Nylon Locknut (21) and the
3/8Ó x 3 1/2Ó Bolt (16).
27. Note: The 3 1/2Ó Pulley (15) labeled in this
step is pre-attached. It is shown removed
for easy part identification.
Route the Short Cable (58) around the 3 1/2Ó
Pulley (15) attached to the upper hole in the
Front Upright (42). Be sure that the Cable
Trap (66) is turned to hold the Cable in
place and that the Cable is routed around
the Pulley as shown. Tighten the 3/8Ó Nylon
Locknut (21) and the 3/8Ó x 3 3/4Ó Bolt (71).
28. Attach the end of the Short Cable (58) to the
Long ÒUÓ-Bracket (57) with a 1/4Ó Nylon Lock-
nut (2) and a 1/4Ó Flat Washer (10). Do not
completely tighten the Nylon Locknut. It
should be threaded onto the end of the
Cable so only a couple of threads are
showing above the nut, as shown in the
inset drawing.
26
27
28
CABLE ASSEMBLY
16
9
17
15
21
71
9
42
15
58
66
58
21
66
57
2
10
58
58
57
2
10
14
29. Attach the Long Cable (23) to the Small ÒUÓ-
Bracket (67) with a 1/4Ó Nylon Locknut (2)
and a 1/4Ó Flat Washer (10). Do not com-
pletely tighten the Nylon Locknut. It
should be threaded onto the end of the
Cable only a couple of turns, as shown in
the inset drawing.
Attach the Small ÒUÓ-Bracket (67) to the
Weight Tube (63) with the 5/16Ó x 1 3/4Ó Bolt
(72) and a 5/16Ó Nylon Locknut (3).
30. Attach the Backrest (41) to the Front Upright
(42) with two 1/4Ó x 2 1/2Ó Screws (43) and
two 1/4Ó Flat Washers (10).
31. Insert the 1/4Ó x 2 1/2Ó Carriage Bolt (38) into
the center hole in the Seat Plate (37). Attach
the Seat Plate to the Seat (13) with two 1/4Ó x
1/2Ó Screws (18).
Insert the 1/4Ó x 2 1/2Ó Carriage Bolt (38) into
the indicated hole in the Seat Frame (36).
Tighten a 1/4Ó Nylon Locknut (2) with a 1/4Ó
Flat Washer (10) onto the Carriage Bolt.
Attach the other end of the Seat (13) to the
Seat Frame (36) with a 1/4Ó Flat Washer (10)
and the 1/4Ó x 2 1/4Ó Screw (24).
31
29
30
CABLE ASSEMBLYSEAT ASSEMBLY
23
67
2
10
63
72
67
3
10 2
23
41
42
10
43
2
24
36
13
37
18
38
10
15
32. Press a 1 3/4Ó Square Inner Cap (44) into the
Press Adjustment Tube (79).
Align one set of holes in the Press Adjustment
Tube (79) with the holes in the Rocker Arm
(32). Insert the ÒLÓ-Pin (40) through the holes.
Be sure that the Press Adjustment Tube is
oriented as shown.
Attach the Press Plate (78) to the Press
Adjustment Tube (79) with a 5/16Ó x 2 1/2Ó
Bolt (22), two 5/16Ó Flat Washers (8), and a
5/16Ó Nylon Locknut (3).
33. Press a 3/4Ó Round Inner Cap (34) into each
end of the Short Pad Tube (28). Press a 3/4Ó
Round Inner Cap into each end of the Long
Pad Tube (80).
Insert the Short Pad Tube (28) into the Seat
Frame (36). Slide a 5 1/2Ó Pad (30) onto each
end of the Short Pad Tube.
Insert the Long Pad Tube (80) into the Leg
Lever (29). Slide a 5 1/2Ó Pad (30) onto each
end of the Long Pad Tube.
34. Make sure that all parts have been properly
tightened. The use of the remaining parts will
be explained in ADJUSTMENT, beginning on
page 16 of this manual.
Before using the home gym system, pull each
cable a few times to be sure that the cables
move smoothly over the pulleys. If one of the
cables does not move smoothly, find and cor-
rect the problem. IMPORTANT: If the cables
are not properly installed, they may be
damaged when heavy weight is used. See
the CABLE DIAGRAM on page 19 of this
manual for proper cable routing. If there is
any slack in the cables, you will need to
remove it by tightening the cables. See
TROUBLE-SHOOTING AND MAINTE-
NANCE on page 18.
32
33
34
DECAL PLACEMENT SEAT ASSEMBLY
44 79 3
8
8
22
Slant must be
turned this way
32
40
78
36
28
80
34
34
30
30
30 29
16
The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise
poster accompanying this manual to see how the home gym system should be set up for each exercise.
IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments are in the cor-
rect starting position for the exercise to be performed. If there is any slack in the cables or chain as an
exercise is performed, the effectiveness of the exercise will be reduced.
54
53
52
23
Lat Bar Holder
39
25 26
54
58
52
53
CHANGING THE WEIGHT SETTING
To change the weight setting of the weight stack,
insert a Weight Pin (26) under the desired Weight
(25). Be sure to insert the Weight Pin until the bent
end of the Weight Pin is touching the Weights, and
turn the bent end downward. The weight setting of the
weight stack can be changed from 6.5 pounds to
106.5 pounds, in increments of 12.5 pounds. Note:
Due to the cables and pulleys, the amount of
resistance at each exercise station may vary from
the weight setting. Use the WEIGHT RESISTANCE
CHART on page 17 to find the approximate
amount of resistance at each weight station.
ATTACHING THE LAT BAR OR NYLON STRAP TO
THE HIGH PULLEY STATION
Attach the Lat Bar (54) to the Long Cable (23) with a
Cable Clip (53). For some exercises, the Chain (52)
should be attached between the Lat Bar and the Long
Cable with two Cable Clips. Adjust the length of the
Chain between the Lat Bar and the Long Cable so
the Lat Bar is in the correct starting position for
the exercise to be performed.
The Nylon Strap (39) can be attached in the same
manner.
ATTACHING THE LAT BAR OR NYLON STRAP TO
THE LOW PULLEY STATION
Attach the Lat Bar (54) to the Short Cable (58) with a
Cable Clip (53). For some exercises, the Chain (52)
should be attached between the Lat Bar and the
Pulley Cable with two Cable Clips. Adjust the length
of the Chain between the Lat Bar and the Short
Cable so the Lat Bar is in the correct starting
position for the exercise to be performed.
The Nylon Strap (39) can be attached in the same
manner.
Always remove the leg press plate and lock the
leg lever before using the low pulley station (see
ADJUSTING AND REMOVING THE LEG PRESS
PLATE AND ADJUSTMENT TUBE and LOCKING
THE LEG LEVER on page 17).
39
Adjustment
17
ADJUSTING AND REMOVING THE LEG PRESS
PLATE AND ADJUSTMENT TUBE
To adjust the position of the Leg Press Plate (78),
remove the ÒLÓ-Pin (40) from the Press Adjustment
Tube (79) and the Rocker Arm (32). Align a different
set of holes in the Press Adjustment Tube with the set
of holes in the Rocker Arm. Re-insert the ÒLÓ-Pin.
For some exercises, the Press Adjustment Tube (79)
must be removed. Remove the ÒLÓ-Pin (40). Lift the
Press Adjustment Tube off the bracket on the Rocker
Arm (32).
LOCKING THE LEG LEVER
When the low pulley station is in use, the Leg Lever
(29) must be locked in place. Insert the ÒLÓ-Pin (40)
through the hole in the Leg Lever and the hole in the
Rocker Arm (32).
32 79
40
78
40
29
32
PRESS BUTTERFLY LEG HIGH LOW LEG
WEIGHT ARM ARM LEVER PULLEY PULLEY PRESS
PLATES (lbs.) (lbs.) (lbs.) (lbs.) (lbs.) (lbs.)
Top 13 9 27 14 32 30
136 2352 305265
257 3281 449397
3 73 46 115 58 121 130
4 99 58 142 69 144 170
5 118 74 171 88 178 215
6 132 88 201 101 217 247
7 151 112 217 114 230 319
8 165 131 264 131 262 347
This chart shows the approximate weight resistance at each station. ÒTopÓ refers to the 6.5 lb. top weight. The
other numbers refer to the 12.5 lb. weight plates. Weight resistance shown for the butterfly arm station is for
each butterfly arm.
The actual resistance at each weight station may vary due to differences in individual weight plates, as well as
friction between the cables, pulleys, and weight guides.
Weight Resistance Chart
18
Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. The
home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.
TIGHTENING THE CABLES
Woven cable, the type of cable used on the home
gym system, can stretch slightly when it is first used.
If there is slack in the cables before resistance is felt,
the cables should be tightened. Slack can be
removed from the cables by tightening the 1/4Ó Nylon
Locknuts (2) at the end of the Long Cable (23) (see
drawing 1) and at the end of the Short Cable (58)
(see drawing 2). To do this you may need to remove
the Small ÒUÓ-Bracket (67) from the Weight Tube (not
shown) or remove the 3 1/2Ó Pulley (15) from the
Long ÒUÓ-Bracket (57). Make sure that the cables are
not too tight or the Top Weight (76) will be lifted off
the weight stack.
Additional slack can be removed by moving the 3 1/2Ó
Pulley (15) to the other hole in the Long ÒUÓ-Bracket
(57). Remove the 3/8Ó Nylon Locknut (21) and the
3/8Ó x 2Ó Bolt (12) from the Cable Trap (66), Pulley,
and ÒUÓ-Bracket. Re-attach the Pulley and Cable Trap.
Be sure that the Cable trap is in the proper position
and that the Cable and Pulley move smoothly.
Note: If a cable tends to slip off the pulleys often,
the cable may have become twisted. Remove the
cable and re-install it.
If the cables need to be replaced, see ORDERING
REPLACEMENT PARTS on the back cover of this
manual.
57
67
76
66
15
2
2
58
12
23
1
2
23
21
Trouble-shooting and Maintenance
19
The cable diagram below shows the proper routing of the Short Cable (58) and the Long Cable (23). Use the
diagram to be sure that the two cables and the cable traps have been assembled correctly. If the cables have
not been correctly routed, the home gym system will not function properly and damage may occur. The numbers
show the correct route for each cable. The starting and ending points of each cable are labeled. Be sure that
the cable traps do not touch or bind the cables.
4
3
2
7
6
5
4
3
2
Weight StackÑ8
6
1ÑLow Pulley
1ÑHigh Pulley
Long Cable (23)
7ÑLong ÒUÓ-Bracket
Short Cable (58)
5
Cable Diagram
1" Round Inner Cap (49)
1" Round Cover Cap (70)
3/4" Round Inner Cap (34)
1/2" x 3/4" Spacer (61)
1 3/4" Square Inner Cap (44)
2" Square Inner Cap (27)
2" Square Outer Cap (51)
1" x 7/8" Plastic Bushing (75)
1" Retainer (69)
3/8" Nylon Locknut (21)
3/8" Nylon Jam Nut (33)
3/8" x 2" Bolt (12)
3/8" x 3 1/2" Bolt (16)
3/8" x 2 1/2" Bolt (7)
3/8" x 3 3/4" Bolt (71)
3/8" x 8" Bolt (59)
Cable Clip (53)
3/8" x 3 1/4" Bolt (35)
5/16" Nylon Locknut (3) 1/4" Nylon Locknut (2)
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice.
Key No. Qty. Description
1 4 5/16Ó x 2 1/2Ó Carriage Bolt
2 3 1/4Ó Nylon Locknut
3 20 5/16Ó Nylon Locknut
4 1 Base
5 1 Stabilizer
6 4 ÒVÓ-Pulley
7 5 3/8Ó x 2 1/2Ó Bolt
8 8 5/16Ó Flat Washer
9 5 3/8Ó Flat Washer
10 6 1/4Ó Flat Washer
11 6 5/16Ó x 2 3/4Ó Bolt
12 3 3/8Ó x 2Ó Bolt
13 1 Seat
14 2 5/16Ó x 2 3/4Ó Carriage Bolt
15 8 3 1/2Ó Pulley
16 3 3/8Ó x 3 1/2Ó Bolt
17 1 Press Frame
18 2 1/4Ó x 1/2Ó Screw
19 2 Weight Bumper
20 1 Pulley Bracket
21 15 3/8Ó Nylon Locknut
22 5 5/16Ó x 2 1/2Ó Bolt
23 1 Long Cable
24 1 1/4Ó x 2 1/4Ó Screw
25 8 Weight
26 1 Weight Pin
27 2 2Ó Square Inner Cap
28 1 Small Pad Tube
29 1 Leg Lever
30 4 5 1/2Ó Pad
31 4 Hand Grip
32 1 Rocker Arm
33 1 3/8Ó Nylon Jam Nut
34 4 3/4Ó Round Inner Cap
35 1 3/8Ó x 3 1/4Ó Bolt
36 1 Seat Frame
37 1 Seat Plate
38 1 1/4Ó x 2 1/2Ó Carriage Bolt
39 1 Nylon Strap
40 1 ÒLÓ-Pin
41 1 Backrest
Key No. Qty. Description
42 1 Front Upright
43 2 1/4Ó x 2 1/2Ó Screw
44 10 1 3/4Ó Square Inner Cap
45 2 10Ó Pad
46 2 Press Arm
47 1 Left Arm
48 1 Right Arm
49 4 1Ó Round Inner Cap
50 4 Long Cable Trap
51 2 2Ó Square Outer Cap
52 1 Chain
53 3 Cable Clip
54 1 Lat Bar
55 1 Top Frame
56 1 Rear Upright
57 1 Long ÒUÓ-Bracket
58 1 Short Cable
59 1 3/8Ó x 8Ó Bolt
60 1 5/16Ó x 6Ó Bolt
61 2 1/2Ó x 3/4Ó Spacer
62 2 Weight Guide
63 1 Weight Tube
64 1 Weight Tube Bumper
65 2 #8 x 3/4Ó Tap Screw
66 6 Cable Trap
67 1 Small ÒUÓ-Bracket
68 1 5/16Ó x 5Ó Bolt
69 4 1Ó Retainer
70 2 1Ó Round Cover Cap
71 3 3/8Ó x 3 3/4Ó Bolt
72 1 5/16Ó x 1 3/4Ó Bolt
73 2 Bumper
74 2 1 1/8Ó x 2 1/2Ó Plastic Bushing
75 2 1Ó x 7/8Ó Plastic Bushing
76 1 Top Weight
77 1 3 1/2Ó Low Pulley
78 1 Leg Press Plate
79 1 Press Adjustment Tube
80 1 Long Pad Tube
# 1 UserÕs Manual
# 1 Exercise Poster
Part ListÑModel No. WESY85290 R0699A
7
50
6
21
69
70
69
70 47
48
44
45
44
45
74
74
11
11
8
8
55
27 12
15 44
15 71
23
21
44
21
49
3
61
60
56
15 321
6
50 7
42
66
6855
3
21
66
15
20
12
12
2
57 58
21
3
5
19
26
51
25
64
63
76
9
21
10
43
10
62
67
3
72
10
2
41
14
51
1
1
4
15
15
33
66
66
49
46
49
46
22
39
16
44
44
15
21
59
75
21
13
27
37
18
38 30
28
34
30
34
3
3
54
31
31
52
53
39
73 65
44
310
2
24 21
6
7
44
79 83
8
22
78
32
73 65
15
66 16
29
16
77
921 34
30
80
58
30
34
21
35
9
21
11
17
36
31
31
33
7
3
71
40
50
44
44
66
8
23
Exploded DrawingÑModel No. WESY85290 R0699A
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information:
1. The MODEL NUMBER of the product (WESY85290).
2. The NAME of the product (WEIDER¨8620 Home Gym System).
3. The SERIAL NUMBER of the product (see the front cover of this manual).
4. The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING at the
center of this manual).
Part No. 156863 J01539-C R0699A Printed in Canada © 1999 ICON Health & Fitness, Inc.
Ordering Replacement Parts

Navigation menu