Weider Club 560 Bench Webe2441 Users Manual *WEBE24410 176980

Weider-Webe24410-Owner-S-Manual weider-webe24410-owner-s-manual

2015-05-18

: Weider Weider-Club-560-Bench-Webe2441-Users-Manual-733450 weider-club-560-bench-webe2441-users-manual-733450 weider pdf

Open the PDF directly: View PDF .
Page Count: 19

Download
Open PDF In Browser	View PDF

Model No. WEBE24410
Serial No.

USER’S MANUAL

Write the serial number in the
space above for reference.

Serial Number Decal

QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained technicians on our customer hot line
will provide immediate assistance, free of charge to you.
CUSTOMER HOT LINE:

1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST

CAUTION
Read all precautions and instructions in this manual before
using this equipment. Save this
manual for future reference.

Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!

TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
Note: A PART LIST/EXPLODED DRAWING is attached in the center of this manual. Remove the PART
LIST/EXPLODED DRAWING before beginning assembly.

WARNING DECAL PLACEMENT
The decal shown at right
has been placed on the
weight rack in the indicated locations. If the decal is
missing or illegible, call
our Customer Service
Department toll-free at
1-800-999-3756, Monday
through Friday, 6 a.m. until
6 p.m. Mountain Time, to
order a free replacement
decal. Apply the replacement decal in the location
shown.

! WARNING
• Misuse of this
product may result in
serious injury.
• Read user’s manual
and follow all warnings
and operating instructions prior to use.
• Do not allow children
on or around machine.
• Replace label if
damaged, illegible,
or removed.

WEIDER is a registered trademark of ICON Health & Fitness, Inc.

IMPORTANT PRECAUTIONS
WARNING:

To reduce the risk of serious injury, read the following important precautions
before using the weight rack.
1.

Read all instructions in this manual before
using the weight rack. Use the weight rack
only as described in this manual.

10. Always secure weights with the weight clips
when they are mounted on the barbell or the
weight carriage.

It is the responsibility of the owner to ensure
that all users of the weight rack are adequately informed of all precautions.

11. Always make sure there is an equal amount
of weight on each end of the barbell or the
weight carriage.

The weight rack is intended for home use
only. Do not use the weight rack in any commercial, rental, or institutional setting.

Use the weight rack only on a level surface.
Cover the floor beneath the weight rack to
protect the floor.

12. Make sure that the cables remain on the pulleys at all times. If the cables bind as you are
exercising, stop immediately and make sure
that the cables are on the pulleys.
13. Always set both weight rests and both
weight spotters at the same height.

5. Inspect and tighten all parts each time you
use the weight rack. Replace any worn parts
immediately.

14. Always exercise with a partner. When you
are performing bench press exercises, squat
exercises, or toe raise exercises, your partner should stand behind you to catch the
barbell if you cannot complete a repetition.

6. Keep children under 12 and pets away from
the weight rack at all times.
7.

Keep hands and feet away from moving parts.

Always wear athletic shoes for foot protection while exercising.

15. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling down.
16. Always move the bench (not included) out of
the way when performing squat exercises.

Do not place more than 300 pounds, including the barbell, on the weight rests. Do not
place more than 150 pounds on the weight
carriage. Note: A barbell and weights are not
included with the weight rack.

17. Always disconnect the lat bar from the
weight rack when performing an exercise
that does not require the lat bar.

WARNING:

Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.

BEFORE YOU BEGIN
Thank you for selecting the versatile CLUB WEIDER®
560 weight rack. The CLUB WEIDER® 560 is designed
to help you develop every major muscle group of the
body. Whether your goal is a shapely figure, dramatic
increase in muscle size and strength, or a healthier
cardiovascular system, the CLUB WEIDER® 560 will
help you achieve the specific results you want.

Monday through Friday, 6 a.m. until 6 p.m. Mountain
Time (excluding holidays). To help us assist you,
please note the product model number and serial
number before calling. The model number is
WEBE24410. The serial number can be found on a
decal attached to the weight rack (see the front cover
of this manual).

For your benefit, read this manual carefully before
using the CLUB WEIDER® 560 weight rack. If you
have additional questions, please call our Customer
Service Department toll-free at 1-800-999-3756,

Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.

High Pulley Station

Chin-up Bar

Lat Bar

Right Side

Left Side

Weight Rest

Weight Carriage

Weight Tube

Weight Spotter

Low Pulley
Station
Note: The terms “right side” and “left side” are
determined relative to a person standing with his
or her back to the rack; they do not correspond
to right and left on the drawings in the manual.

PART IDENTIFICATION CHART
Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts
may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached.

M10 x 45mm Bolt (34)

51mm Spacer (43)
M10 Flat Washer (41)

M10 x 50mm Bolt (47)

M8 Flat Washer (40)

28mm Spacer (44)
M10 x 66mm Bolt (37)

M8 x 72mm Bolt (35)
M10 Nylon Locknut (31)

24mm Spacer (42)

M10 x 75mm Bolt (36)

M8 Nylon Locknut (32)

18mm Spacer (45)

M10 x 78mm Bolt (33)

ASSEMBLY
• As you assemble the weight rack, make sure all
parts are oriented as shown in the drawings.

Make Things Easier for Yourself
Everything in this manual is designed to ensure
that the weight rack can be assembled successfully by anyone. However, it is important to realize that the versatile weight rack has many parts
and that the assembly process will take time.
Most people find that by setting aside plenty of
time, assembly will go smoothly.

• For help identifying small parts, use the PART
IDENTIFICATION CHART on page 5.
The following tools (not included) are required
for assembly:
• Two adjustable wrenches
• One rubber mallet

Before beginning assembly, carefully read the
following information and instructions:

• One standard screwdriver

• Assembly requires two people.

• One Phillips screwdriver

• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.

• Lubricant, such as grease or petroleum jelly,
and soapy water.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.

• Tighten all parts as you assemble them, unless
instructed to do otherwise.

Before beginning assembly, make sure you
understand the information in the box above.
Important: Some of the parts described in the
assembly steps may be pre-assembled.

28
31
2

Press four 60mm Square Outer Caps (28) onto the
ends of the Right and Left Bases (1, 3).

28
33

Attach the Right and Left Bases (1, 3) to the Center
Base (2) using four M10 x 78mm Bolts (33) and
four M10 Nylon Locknuts (31). Do not tighten the
Nylon Locknuts yet.

2. Press a 60mm Square Outer Cap (28) onto the end
of the Weight Guide Base (4).

2
28
4

Attach the Foot Plate (5) and the Weight Guide
Base (4) to the Center Base (2), as shown, using
two M10 x 78mm Bolts (33) and two M10 Nylon
Locknuts (31). Do not tighten the Nylon Locknuts
yet.

5
33

31
31

3. Identify the two Rear Uprights (8), which are slightly
shorter than the Front Uprights (not shown).

Attach the Rear Uprights to the Right and Left
Bases (1, 3) using four M10 x 78mm Bolts (33) and
four M10 Nylon Locknuts (31). Do not tighten the
Nylon Locknuts yet. Make sure the Uprights are
oriented exactly as shown, with the adjustment
holes on the indicated side near the bottom.

Adjustment
Holes
8
8
31
33
1

4. Tap a 60mm Square Inner Cap (29) into each of the
Front Uprights (7).

29
8

Attach one of the Front Uprights (7) and two Joint
Plates (6) to the Left Base (3) using four M10 x
78mm Bolts (33) and four M10 Nylon Locknuts (31).
Make sure the Front Upright is oriented so the
holes near the bottom of the Front Upright and
the holes in the Joint Plates line up. If they do
not line up, turn the Front Upright upside-down.
Do not tighten the Nylon Locknuts yet. Make
sure the Front Upright is turned so the adjustment holes are facing the Rear Upright (8) and
the number decals on the Front Uprights are facing each other.

33
31

Attach the other Front Upright (7, not shown) and
two Joint Plates (6, not shown) to the Right Base
(1) in the same manner.

3
6
31

6
5. Refer to drawing 5a. Press six Square Bushings
(21) into the Right Weight Rest (19) and the Right
Weight Spotter (20) as shown. Pull out the
Adjustment Knobs (22) and slide the Right Weight
Spotter and the Right Weight Rest down over the
right Uprights (7, 8) as indicated.

5a
21

8
7

Refer to drawing 5b. Secure the Right Weight
Spotter (20) and the Right Weight Rest (19) to the
right Uprights (7, 8) by tightening each of the three
Adjustment Knobs (22) into an adjustment hole in
the Uprights.

22
19

Assemble the Left Weight Spotter (not shown) and
Left Weight Rest (not shown) on the left Uprights
(7, 8) in the same manner. Make sure both Weight
Spotters and both Weight Rests are at the same
height.

21
8
7

6. Attach the Chin-up Bar (13) and two Joint Plates (6)
to the Front Uprights (7) using four M10 x 78mm
Bolts (33) and four M10 Nylon Locknuts (31). Do
not tighten the Nylon Locknuts yet.

13
31
6
31

7
7. Press a 60mm Square Inner Cap (29) into the Left
Frame (12). Attach the Left Frame to the left
Uprights (7, 8) using four M10 x 78mm Bolts (33)
and four M10 Nylon Locknuts (31). Do not tighten
the Nylon Locknuts yet.

11
10
31

Assemble the Right Frame (10) to the right Uprights
(7, 8) in the same manner.

31
33

Attach the Center Frame (11) to the Right and Left
Frames (10, 12) using four M10 x 78mm Bolts (33)
and four M10 Nylon Locknuts (31).

12
31

33
Tighten all Nylon Locknuts used in steps 1–7.

8. Press the two 51mm Round Inner Caps (46) into
the weight tubes on the Weight Carriage (15).

Press the two Carriage Bushings (16) into the
Weight Carriage (15). Make sure the Weight
Carriage is turned so the weight tubes are near
the top, as shown. Attach the lower Carriage
Bushing using an M10 x 66mm Bolt (37), two M10
Flat Washers (41), the 51mm Spacer (43), and an
M10 Nylon Locknut (31).

16
15
Weight Tube
31
46

41
16

9. Set the two Weight Bumpers (18) over the indicated
holes in the Weight Guide Base (4). Hold the
Weight Carriage (15) on top of the Weight
Bumpers.

43 41
37

9
9

Insert the two Weight Guides (9) into the Weight
Carriage (15), the Weight Bumpers (18), and the
Weight Guide Base (4). Attach the Weight Guides
using two M8 x 72mm Bolts (35), four M8 Flat
Washers (40), and two M8 Nylon Locknuts (32).

32
18
4
40
35

10. Press a 60mm Square Inner Cap (29) into the end
of the Weight Guide Frame (14).

Hold the Weight Guide Frame (14) on top of the
Center Frame (11) and the Weight Guides (9).
Attach the Weight Guides to the Weight Guide
Frame using two M8 x 72mm Bolts (35), four M8
Flat Washers (40), and two M8 Nylon Locknuts (32).

40
14
35
11

Attach the Weight Guide Frame (14) to the Center
Frame (11) using two M10 x 78mm Bolts (33), two
M10 Flat Washers (41), and two M10 Nylon
Locknuts (31).

9
41
31

11. Locate the High Cable (26), which is the longer of
the two Cables. Notice that there is a single ball on
one end of the High Cable and a metal sleeve on
the other end.

Route the metal-sleeve end of the High Cable (26)
up under the lat bar rest on the Weight Guide
Frame (14), down through the indicated hole, back
up through the next hole, and then down through
the hole between the Weight Guides (9), as shown.

Lat Bar
Rest

12. Insert the end of the High Cable (26) into the hole
in the center of the Weight Carriage (15). Attach the
High Cable using an M10 x 66mm Bolt (37), two
M10 Flat Washers (41), two 24mm Spacers (42),
and an M10 Nylon Locknut (31).

41
31

26
42
41
37

13. Lift the High Cable (26) in the location shown.
Attach two Pulleys (25) inside the bracket on the
Weight Guide Frame (14) using two M10 x 50mm
Bolts (47) and two M10 Nylon Locknuts (31).

25
26
31

14. Lift the High Cable (26) in the location shown.
Attach two Pulleys (25) inside the Weight Guide
Frame (14) using two M10 x 75mm Bolts (36), four
M10 Flat Washers (41), four 18mm Spacers (45),
and two M10 Nylon Locknuts (31).

25
41

41
45

41
36

45
41

15. Pull the High Cable (26) down in the indicated location, so there is no slack at the ends of the High
Cable.

Locate the Low Cable (27), which is shorter and
has two balls on one end. Insert the metal-sleeve
end of the Low Cable into the indicated hole in the
Weight Guide Base (4). Attach the Low Cable using
an M10 x 75mm Bolt (36), two M10 Flat Washers
(41), two 28mm Spacers (44), and an M10 Nylon
Locknut (31).

Route the ball-end of the Low Cable (27) through
the bracket on the Center Base (2). Attach a Pulley
(25) inside the bracket using an M10 x 45mm Bolt
(34) and an M10 Nylon Locknut (31).
27
25
41 44

2 31

4
41
36

34
16. Hold a Pulley (25) in the High Cable (26) as shown.
Attach a Cable Trap (24) and the two Pulley Plates
(17) to the Pulley using an M10 x 45mm Bolt (34)
and an M10 Nylon Locknut (31).

26
17

31
Lay the Low Cable (27) over a Pulley (25) as
shown. Attach the Pulley and a Cable Trap (24) to
the Pulley Plates (17) using an M10 x 45mm Bolt
(34) and an M10 Nylon Locknut (31). Make sure
the Bolts are inserted through the highest and
lowest holes in the Pulley Plates. In addition,
make sure the Cables are between the Cable
Traps and the Pulleys.

24
17

24
27

17. Wet the ends of the Lat Bar (38) with a small
amount of soapy water. Slide the Handgrips (30)
onto the ends of the Lat Bar.

18. Make sure all parts of the weight rack are properly tightened. In addition, pull each cable a few times
to make sure the cables move smoothly over the pulleys. If the cables do not move smoothly, locate
and correct the problem. When weights are used, the cables may be damaged if they are incorrectly
routed.
The use of all remaining parts will be explained in ADJUSTMENTS, beginning on page 12.

ADJUSTMENTS
This section explains how to adjust the weight rack. See the EXERCISE GUIDELINES on page 14 for important
information about how to get the most benefit from your exercise program. Also, refer to the accompanying exercise guide to see the correct form for each exercise.
Inspect and tighten all parts each time you use the weight rack. Replace any worn parts immediately. The weight
rack can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
USING THE WEIGHT RESTS AND WEIGHT
SPOTTERS
Before beginning an exercise, move the Weight Rests
(19, 48) and the Weight Spotters (20, 49) to sets of
holes in the uprights that are best suited for that exercise. The selected holes for the Weight Spotters should
represent the lowest point to which you want the barbell
to go during the exercise. The selected holes for the
Weight Rests should be at a comfortable height for lifting
and replacing the barbell. Perform the exercise as
shown in the accompanying exercise guide. Note: Make
sure the Adjustment Knobs (22) are fully tightened.

19
20

WARNING:

Always set both Weight
Rests (19, 48) at the same height and both
Weight Spotters (20, 49) at the same height.

SETTING UP THE RACK FOR SQUAT EXERCISES
Squat exercises should be performed inside the rack
(behind the dotted line in the picture). When performing
squat exercises, set the Weight Rests (19, 48) and the
Weight Spotters (20, 49) at a comfortable height.

WARNING:

Always move the bench
(not included) when you are performing squat
exercises inside the rack.

Squat
Area

ATTACHING WEIGHTS TO THE WEIGHT CARRIAGE
To use the high or low pulley station, slide the desired
amount of weight onto the weight tubes of the Weight
Carriage (15) and secure the weights with Weight Clips
(50).

Weight
Tube

WARNING:

Do not place more than
150 pounds on the Weight Carriage (15). Always
place the same amount of weight on each side of
the Weight Carriage. Always secure the weights

15
50

ATTACHING THE LAT BAR TO THE HIGH PULLEY
STATION OR THE LOW PULLEY STATION

To use the high pulley station or the low pulley station,
first place the desired weights on the Weight Carriage
(see ATTACHING WEIGHTS TO THE WEIGHT CARRIAGE, above). Next, attach the Lat Bar (38) to the
High Cable (26) or the Low Cable (not shown) with a
Cable Clip (23).

WARNING:

Always disconnect the
Lat Bar (38) when performing an exercise that
does not require using the Lat Bar.

TIGHTENING THE CABLES
Woven cable, the type of cable used on the weight rack,
can stretch slightly after it is first used. If there is slack
in the cables, tighten them as described below.

Remove the M10 x 45mm Bolt (34) and the M10 Nylon
Locknut (31) attaching the lower Pulley (25) and Cable
Trap (24) to the two Pulley Plates (17). Reattach the
lower Pulley and Cable Trap to the higher holes in the
Pulley Plates using the Bolt and Nylon Locknut.

24
If moving just the lower Pulley (25) does not sufficiently
tighten the cables, you can also move the upper Pulley
down one set of holes in the Pulley Plates (17).

EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS

PERSONALIZING YOUR EXERCISE PROGRAM

Muscle Building
To increase the size and strength of your muscles,
push them close to their maximum capacity. Your muscles will continually adapt and grow as you progressively increase the intensity of your exercise. You can
adjust the intensity level of an individual exercise in
two ways:
• by changing the amount of weight used
• by changing the number of repetitions or sets performed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)

Determining the exact length of time for each workout,
as well as the number of repetitions or sets completed,
is an individual matter. It is important to avoid overdoing it during the first few months of your exercise program. You should progress at your own pace and be
sensitive to your body’s signals. If you experience pain
or dizziness at any time while exercising, stop immediately and begin cooling down. Find out what is wrong
before continuing. Remember that adequate rest and a
proper diet are important factors in any exercise program.
WARMING UP

The proper amount of weight for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of weight that is right
for you. Begin with 3 sets of 8 repetitions for each
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of weight.

Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and delivering more oxygen to your muscles.
WORKING OUT

Toning
You can tone your muscles by pushing them to a moderate percentage of their capacity. Select a moderate
amount of weight and increase the number of repetitions in each set. Complete as many sets of 15 to 20
repetitions as possible without discomfort. Rest for 1
minute after each set. Work your muscles by completing more sets rather than by using high amounts of
weight.

Each workout should include 6 to 10 different exercises. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.

Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.

EXERCISE FORM

Cross Training
Cross training is an efficient way to get a complete and
well-balanced fitness program. An example of a balanced program is:
• Plan weight training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
cycling or swimming, on Tuesday and Thursday.
• Rest from both weight training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
The combination of weight training and aerobic exercise will reshape and strengthen your body, and develop your heart and lungs.

Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise, and
moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompanying this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on page
15 to find the names of the muscles.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath.

Rest for a short period of time after each set. The
ideal resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
• Rest for one minute after each set for a toning workout.
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.

slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is an effective way to increase flexibility.
STAYING MOTIVATED
For motivation, keep a record of each workout. List
the date, the exercises performed, the weight used,
and the numbers of sets and repetitions completed.
Record your weight and key body measurements at
the end of every month. Remember, the key to
achieving the greatest results is to make exercise a
regular and enjoyable part of your everyday life.

COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move

MUSCLE CHART
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
O.
P.
Q.
R.
S.
T.
U.
V.
W.

Sternomastoid (neck)
Pectoralis Major (chest)
Biceps (front of arm)
Obliques (waist)
Brachioradials (forearm)
Hip Flexors (upper thigh)
Abductor (outer thigh)
Quadriceps (front of thigh)
Sartorius (front of thigh)
Tibialis Anterior (front of calf)
Soleus (front of calf)
Rectus Abdominus (stomach)
Adductor (inner thigh)
Trapezius (upper back)
Rhomboideus (upper back)
Deltoid (shoulder)
Triceps (back of arm)
Latissimus Dorsi (mid back)
Spinae Erectors (lower back)
Gluteus Medius (hip)
Gluteus Maximus (buttocks)
Hamstring (back of leg)
Gastrocnemius (back of calf)

N
A

S
F

ORDERING REPLACEMENT PARTS
To order replacement parts, call our Customer Service Department toll-free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give
the following information when calling:
• The MODEL NUMBER of the product (WEBE24410)
• The NAME of the product (CLUB WEIDER® 560 weight rack)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING at the center of this manual).

LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product at one of its authorized service centers. All products for which warranty claim is made must be received by ICON at one of its authorized service centers with all freight and other
transportation charges prepaid, accompanied by sufficient proof of purchase. All returns must be pre-authorized by ICON. This warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON
authorized service center, products used for commercial or rental purposes, or products used as store display
models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813

Part No. 176980 R0701A

REMOVE THIS PART LIST/EXPLODED
DRAWING FROM THE MANUAL

SAVE THIS PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE

PART LIST—Model No. WEBE24410
Key No.

Qty.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27

1
1
1
1
1
6
2
2
2
1
1
1
1
1
1
2
2
2
1
1
12
6
1
2
7
1
1

Description
Right Base
Center Base
Left Base
Weight Guide Base
Foot Plate
Joint Plate
Front Upright
Rear Upright
Weight Guide
Right Frame
Center Frame
Left Frame
Chin-up Bar
Weight Guide Frame
Weight Carriage
Carriage Bushing
Pulley Plate
Weight Bumper
Right Weight Rest
Right Weight Spotter
Square Bushing
Adjustment Knob
Cable Clip
Cable Trap
Pulley
High Cable
Low Cable

R0701A

Key No. Qty.
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
#
#

5
5
2
46
4
36
3
4
3
2
1
1
8
12
2
1
2
4
2
2
1
1
2
4
1
1

Description
60mm Square Outer Cap
60mm Square Inner Cap
Handgrip
M10 Nylon Locknut
M8 Nylon Locknut
M10 x 78mm Bolt
M10 x 45mm Bolt
M8 x 72mm Bolt
M10 x 75mm Bolt
M10 x 66mm Bolt
Lat Bar
Strap
M8 Flat Washer
M10 Flat Washer
24mm Spacer
51mm Spacer
28mm Spacer
18mm Spacer
51mm Round Inner Cap
M10 x 50mm Bolt
Left Weight Rest
Left Weight Spotter
Weight Clip
Weight Clip Sleeve
User’s Manual
Exercise Guide

Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the user’s manual for information about ordering replacement parts.

EXPLODED DRAWING—Model No. WEBE24410

41
45

41 37

16
42 41
37

44 41

41
15
16
18

32
31 41

31 41

EXPLODED DRAWING—Model No. WEBE24410
R0701A

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2002:12:12 06:14:12
Producer                        : Acrobat Distiller 4.05 for Macintosh
Author                          : It's Me
Creator                         : QuarkXPress Passportª: PSPrinter 8.3.1
Title                           : *WEBE24410-176980
Modify Date                     : 2002:12:12 06:14:15-06:00
Page Count                      : 19

EXIF Metadata provided by EXIF.tools

Weider Club 560 Bench Webe2441 Users Manual *WEBE24410 176980

Weider-Webe24410-Owner-S-Manual weider-webe24410-owner-s-manual

Navigation menu

Versions of this User Manual:

Views

Navigation