Weider Pro 800 Bench 15074 Users Manual *150740 163192
Weider-Pro800-Users-Manual-233737 weider-pro800-users-manual-233737
Weider-150740-Owner-S-Manual weider-150740-owner-s-manual
PRO800 to the manual 4931199d-307f-40d8-81d7-1dfc1f7da0af
2015-05-18
: Weider Weider-Pro-800-Bench-15074-Users-Manual-732991 weider-pro-800-bench-15074-users-manual-732991 weider pdf
Open the PDF directly: View PDF 
.
Page Count: 16
| Download | |
| Open PDF In Browser | View PDF |
¨ Model No. 831.150740 Serial No. USERÕS MANUAL Write the serial number in the space above for future reference. Serial Number Decal (Under Seat) SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179 CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. Visit our website at www.weiderfitness.com new products, prizes, fitness tips, and much more! Table of Contents WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 USING THE WEIGHT BENCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover FULL 90 DAY WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover Warning Decal Placement The decal shown at the right has been applied to the weight bench. If the decal is missing, or if it is not legible, please call our toll-free HELPLINE at 1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays), to order a free replacement decal. Apply the replacement decal in the location shown. 2 Important Precautions WARNING: To reduce the risk of serious injury, read the following important precautions before using the weight bench. tion while exercising. 12. The weight bench does not include weights. The weight bench is designed to support a maximum of 460 pounds, including the user, a weight bar, and weights. Do not place more that 210 pounds, including a weight bar and weights, on the weight rests. Do not place more than 130 pounds on the leg lever. 1. Read all instructions in this manual before using the weight bench. 2. It is the responsibility of the owner to ensure that all users of the weight bench are adequately informed of all precautions. 3. Use the weight bench only as described in this manual. 13. Make sure that the adjustment knobs are inserted completely and tightened into the uprights before beginning any exercise. 4. Use the weight bench only on a level surface. Cover the floor beneath the weight bench for protection. 14. When adjusting the position of the seat, make sure that the adjustment pin is inserted through both adjustment tubes before beginning any exercise (see page 10). 5. Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. 15. If you feel pain or dizziness at any time while exercising, stop immediately and begin cooling down. 6. Keep children under the age of 12 and pets away from the weight bench at all times. 7. Always be sure there is an equal amount of weight on each side of your barbell (not included) when you are using it. When adding or removing weights, always keep some weight on both ends of the barbell and prevent the barbell from tipping. 16. The weight bench is intended for home use only. Do not use the weight bench in any commercial, rental, or institutional setting. 17. Always remove the curl post from the front leg before performing leg curls with the leg lever. 8. Do not use a barbell that is longer than six feet with the weight bench. 18. Always exercise with a partner. When you are performing bench press exercises, your partner should stand behind you to catch the barbell if you cannot complete a repetition. 9. When you are using the leg lever, place a barbell with the same amount of weight on the weight rests to balance the bench. 10. Keep hands and feet away from moving parts. 19. When you put weight on the weight rests, make sure you put at least ten pounds on the leg lever to balance the weight bench. 11. Always wear athletic shoes for foot protec- WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over the age of 35 or persons with pre-existing health problems. Read all instructions before using. SEARS assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 3 Before You Begin Thank you for selecting the WEIDER¨ PRO800 Weight Bench. The versatile WEIDER¨ PRO 800 Weight Bench is designed to be used with your own weight set (not included) to develop every major muscle group of the body. Whether your goal is a shapely figure, dramatic muscle size and strength, or a healthier cardiovascular system, the WEIDER¨ PRO800 will help you to achieve the specific results you want. HELPLINE at 1-800-736-6879, Monday through Saturday, 7 a.m. until 7 p.m. Central Time (excluding holidays). To help us assist you, please note the product model number and serial number before calling. The model number is 831.150740. The serial number can be found on a decal attached to the weight bench (see the front cover of this manual). Before reading further, please look at the drawing below and familiarize yourself with the parts that are labeled. For your benefit, read this manual carefully before using the WEIDER¨ PRO800 Weight Bench. If you have additional questions, please call our toll-free Weight Rests Upright Adjustment Knob Curl Pad Backrest Adjustment Tubes Seat Leg Lever Weight Tube 4 Part Identification Chart This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below each part refers to the key number of the part. The second number refers to the quantity needed for assembly. Important: Some parts may have been pre-assembled for shipping purposes. If you cannot find a part in the parts bags, check to see if it has been pre-assembled. M10 x 81mm Bolt (35)Ñ10 M10 x 72mm Bolt (40)Ñ1 M10 x 178mm Bolt (17)Ñ1 M6 Washer (25)Ñ4 M10 x 65mm Bolt (18)Ñ2 M8 Washer (38)Ñ2 M8 x 58mm Bolt (39)Ñ1 M6 x 38mm Screw (16)Ñ4 M10 Washer (24)Ñ4 M6 x 16mm Screw (15)Ñ6 M8 Nylon Locknut (13)Ñ1 M4 x 16mm Screw (34)Ñ4 M10 Nylon Locknut (19)Ñ14 Spacer (37)Ð1 5 Assembly ¥ As you assemble the weight bench, make sure that all parts are oriented as shown in the drawings. Before beginning assembly, carefully read the following information and instructions: ¥ Place all parts of the weight bench in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed. THE FOLLOWING TOOLS (NOT INCLUDED) ARE REQUIRED FOR ASSEMBLY: ¥ Two (2) adjustable wrenches ¥ Read each assembly step before you begin. ¥ One (1) phillips screwdriver ¥ For help identifying the small parts used in assembly, use the PART IDENTIFICATION CHART on the previous page. Note: Some small parts may have been pre-attached for shipping purposes. If a part is not in the parts bag, check to see if it has been pre-attached. ¥ One (1) rubber mallet ¥ Lubricant, such as grease or petroleum jelly, and soapy water will also be needed. Assembly will be more convenient if you have the following tools: A socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches. ¥ Tighten all parts as you assemble them, unless instructed to do otherwise. 1. Before assembling this weight bench, be sure that you have read and understand the information in the box above. 1 1 The weight bench is designed to be used with a mid-width weight set (not included). To use the weight bench with an olympic-size weight set, an optional olympic expansion kit is available to purchase (model number 831.150780). 30 7 Warning Decal 1 20 19 7 Position the Crossbar (3) as shown. (Note: If you purchased the optional olympic expansion kit, place the olympic crossbar in place of the standard crossbar.) Attach the Crossbar to each Upright Base (7) with four M10 x 81mm Bolts (35), a Support Plate (20) and four M10 Nylon Locknuts (19). Note the position of the warning decal and make sure the Upright Bases are oriented exactly as shown. 3 20 30 20 35 20 35 Slide the Uprights (1) into the desired position in the Upright Base (7) and secure them with two M10 x 67mm Adjustment Knobs (30). 2 2. Attach the Frame (2) to the Crossbar (3) with two M10 x 81mm Bolts (35), the ÒUÓ Bracket, (14) and two M10 Nylon Locknuts (19). Make sure the ÒUÓ Bracket is oriented exactly as shown. Note: the Frame (2) must be seated firmly against the Crossbar (3) so that the ÒUÓ Bracket can fit over both of them. 2 3 35 19 6 19 14 3. Attach the Front Leg (8) to the Frame (2) with two M10 x 65mm Bolts (18), two M10 Washers (24), and two M10 Nylon Locknuts (19). 3 19 2 24 18 19 8 4. Tap three 45mm Square Inner Caps (21) into the ends of the Leg Lever (4) as shown. 4 21 Tap a 1Ó Round Inner Cap (23) into the indicated end of the Weight Tube (41). 4 Insert the Weight Tube (41) into the indicated hole in the Leg Lever (4). Press a 1Ó Angle Cap (29) onto the indicated end of the Weight Tube. 21 41 29 Note: If you purchased the optional olympic expansion kit, attach the olympic sleeve to the Weight Tube as shown in the accessory manual. 23 5. Lubricate an M10 x 72mm Bolt (40). Attach the Leg Lever (4) to the Front Leg (8) with the Bolt and an M10 Nylon Locknut (19). 21 5 8 19 4 Attach the Spacer (37) to the Leg Lever (4) with the M8 x 58mm Bolt (39), two M8 Washers (38), and an M8 Nylon Locknut (13). Note: The Spacer will fit tightly inside of the Leg Lever. 39 38 40ÐLubricate 37 38 13 6. Press four 1Ó Square Inner Caps (12) into the indicated ends of the Backrest Tubes (5, 42). Press two 1Ó x 2Ó Inner Caps (36) into the ends of the adjustment tubes. 6 6 Wide End With the wide end of the Backrest (6) positioned as shown, attach the Backrest Tubes (5, 42) to the Backrest with four M6 x 38mm Screws (16) and four M6 Washers (25). Note: The Backrest Tubes and Backrest must be oriented exactly as shown. 12 25 5 42 Adjustment Tubes 12 25 16 36 7 16 25 16 7. Lubricate the M10 x 178mm Bolt (17). Attach the Backrest (6) to the Frame (2) with the Bolt, two M10 Washers (24), and an M10 Nylon Locknut (19). 7 6 Secure the Backrest (6) to the Frame (2) with the Adjustment Pin (32) through one of the three sets of holes in the adjustment tubes. Secure the Adjustment Pin with the Pin Clip (43). Adjustment Tubes 32 17ÑLubricate Make sure the Adjustment Pin (32) is completely inserted through both holes in the adjustment tubes. 24 19 8. With the wide end of the Seat (11) positioned as shown, attach the Seat to the brackets on the Frame (2) with four M6 x 16mm Screws (15). 2 43 8 11 Wide End 2 15 9. Attach the Curl Pad (27) to the Curl Post (26) with two M6 x 16mm Screws (15). 9 27 15 26 10. Slide the Curl Post (26) into the Front Leg (8). Align one of the adjustment holes in the Curl Post with the adjustment hole in the Front Leg. Tighten the M10 x 48mm Adjustment Knob (33) into the adjustment hole in the Front Leg. Make sure that you fully tighten the Adjustment Knob. 10 26 8 33 8 11. Tap two 3/4Ó Round Inner Caps (9) into each Pad Tube (10). Insert the Pad Tubes into the holes in the Leg Lever (4) and the Front Leg (8). Slide two Foam Pads (22) onto each Pad Tube. 11 22 12. Make sure that all parts are properly tightened before you use the weight bench. The use of all remaining parts will be explained in USING THE WEIGHT BENCH beginning below. 10 4 8 9 10 9 10 22 Using the Weight Bench The weight bench is designed to be used with your own weight set (not included). The steps below explain how the weight bench can be adjusted. See EXERCISE GUIDELINES on page 11 for important exercise information and refer to the accompanying exercise poster to see the correct form for several exercises. Refer also to the exercise information accompanying your weight set (not included) for additional exercises. Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents. ATTACHING WEIGHTS TO THE LEG LEVER To use the Leg Lever (4), slide the desired weights (not included) onto the Weight Tube (41). 4 WARNING: Do not place more than 130 pounds on the leg lever. Note: If you purchased the optional olympic expansion kit, attach the olympic sleeve to the weight tube as shown in the accessory manual. 41 Weight REMOVING THE PAD TUBE AND PADS To do leg curl exercises, the indicated Pad Tube (10) and Pads (22) must be removed from the weight bench. To do this, slide one of the Pads off the Tube, then pull the Tube out of the holes. 22 10 22 9 ATTACHING THE CURL POST Note: When the Curl Post (26) is not in use, the 45mm Square Inner Cap (21) should be inserted into the Front Leg (8). For some exercises, the Curl Post (26) must be attached to the weight bench. 21 26 33 Slide the Curl Post (26) into the Front Leg (8). Align one of the adjustment holes in the Curl Post with the adjustment hole in the Front Leg. Tighten the M10 x 54mm Adjustment Knob (33) into the adjustment hole in the Front Leg. Make sure that you fully tighten the Adjustment Knob. 8 ADJUSTING THE UPRIGHTS 1 30 1 The Uprights (1) can be adjusted to five heights to accommodate different exercises. To adjust the height, remove the M10 x 67mm Adjustment Knobs (30) from both Uprights and Upright Bases (7). Slide the Uprights to the desired position and re-insert the Adjustment Knobs. 7 WARNING: Always set both uprights at the same height. Make sure that the adjustment knobs are inserted completely and tightened into the uprights before beginning any exercise. 30 7 ADJUSTING THE BACKREST 6 32 The Backrest (6) can be used in either a decline position, a level position or two incline positions. To adjust the Backrest to the decline position, remove the Adjustment Pin (32) and lower the Backrest until it rests directly on the Crossbar (3). Re-insert the Adjustment Pin. To adjust the Backrest (6) to the level position, insert the Adjustment Pin (32) through the top set of holes. To adjust the Backrest (6) to an incline position, insert the Adjustment Pin (32) as shown through one of the three sets of holes in the backrest adjustment tubes. Slide the Adjustment Pin completely through both holes in the adjustment tubes. Secure the Adjustment Pin with the Pin Clip (43). WARNING: When adjusting the position of the seat, make sure that the adjustment pin is inserted through both adjustment tubes before beginning any exercise. 10 43 Adjustment Tubes 3 Exercise Guidelines THE FOUR BASIC TYPES OF WORKOUTS PERSONALIZING YOUR EXERCISE PROGRAM ¥ Muscle Building We have not specified an exact length of time for each workout, or a specific number of repetitions or sets for each exercise. It is very important to avoid overdoing it during the first few months of your exercise program, and to progress at your own pace. If you experience pain or dizziness at any time while exercising, stop immediately and begin to cool down. Find out what is wrong before continuing. Remember that adequate rest and a proper diet are also important. In order to increase the size and strength of your muscles, you must push your muscles to a high percentage of their capacity. You must also progressively increase the intensity of your exercise so that your muscles will continually adapt and grow. Each individual exercise can be tailored to the proper intensity level by changing the amount of weight used, or the number of repetitions or sets performed. (A ÒrepetitionÓ is one complete cycle of an exercise, such as one sit-up. A ÒsetÓ is a series of repetitions performed consecutively.) WARMING UP Begin each workout with 5 to 10 minutes of light stretching and exercise to warm up. Warming up prepares your body for exercise by increasing circulation, raising your body temperature and delivering more oxygen to your muscles. The proper amount of weight for each exercise depends upon the individual user. It is up to you to gauge your limits. Select the amount of weight that you think is right for you. Begin with 3 sets of 8 repetitions for each exercise that you perform. Rest for 3 minutes after each set. When you can complete 3 sets of 12 repetitions without difficulty, increase the amount of weight. WORKING OUT Each workout should include 6 to 10 different exercises. Select exercises for every major muscle group, with emphasis on the areas that you want to develop the most. To give balance and variety to your workouts, vary the exercises from workout to workout. ¥ Toning To tone your muscles, you must push your muscles to a moderate percentage of their capacity. Select a moderate amount of weight and increase the number of repetitions in each set. Complete as many sets of 15 to 20 repetitions as possible without discomfort. Rest for 1 minute after each set. Work your muscles by completing more sets rather than by using high amounts of weight. Schedule your workouts for the time of day when your energy level is the highest. Each workout should be followed by at least one day of rest. Once you find the schedule that is right for you, stick with it. EXERCISE FORM ¥ Weight Loss In order to obtain the greatest benefits from exercising, it is essential to maintain proper form. To lose weight, use a low amount of weight and increase the number of repetitions in each set. Exercise for 20 to 30 minutes, resting for a maximum of 30 seconds between sets. Maintaining proper form means moving through the full range of motion for each exercise, and moving only the appropriate parts of the body. Exercising in an uncontrolled manner will leave you feeling exhausted. On the exercise poster accompanying this manual, you will find photographs showing the correct form for several exercises. A description of each exercise is also provided, along with a list of the muscles affected. Refer to the muscle chart on page 12 to find the locations of the muscles. ¥ Cross Training In the pursuit of a complete and well-balanced fitness program, many have found that cross training is the answer. We recommend that on Monday, Wednesday and Friday, you plan weight training workouts. On Tuesday and Thursday, plan 20 to 30 minutes of aerobic exercise, such as cycling, running or swimming. Rest from both weight training and aerobic exercise for at least one full day each week to give your body time to regenerate. By combining weight training with aerobic exercise, you can reshape and strengthen your body, plus develop a stronger heart and lungs. The repetitions in each set should be performed smoothly and without pausing. The exertion stage of each repetition should last about half as long as the return stage. Proper breathing is important. Exhale during the exertion stage of each repetition and inhale during the return stroke; never hold your breath. Rest 11 for 3 minutes after each set if you are doing a muscle building workout, 1 minute after each set if you are doing a toning workout, and 30 seconds after each set if you are doing a weight loss workout. Plan to spend the first couple of weeks familiarizing yourself with the equipment and learning the proper form for each exercise. STAYING MOTIVATED For motivation, keep a record of each workout. The charts on page 13 of this manual can be photocopied and used to schedule and record your workouts. List the date, exercises performed, weight, and numbers of sets and repetitions completed. Record your weight and key body measurements at the end of every month. COOLING DOWN End each workout with 5 to 10 minutes of stretching. Include stretches for both your arms and legs. Move slowly as you stretchÑdo not bounce. Ease into each stretch gradually and go only as far as you can without strain. Stretching at the end of each workout is very effective for increasing flexibility. Remember, the key to achieving the greatest results is to make exercise a regular and enjoyable part of your everyday life. MUSCLE CHART A. B. C. D. E. F. G. H. I. J. K. L. M. N. O. P. Q. R. S. T. U. V. W. Sternomastoid (neck) Pectoralis Major (chest) Biceps (front of arm) Obliques (waist) Brachioradials (forearm) Hip Flexors (upper thigh) Abductor (outer thigh) Quadriceps (front of thigh) Sartorius (front of thigh) Tibialis Anterior (front of calf) Soleus (front of calf) Rectus Abdominus (stomach) Adductor (inner thigh) Trapezius (upper back) Rhomboideus (upper back) Deltoid (shoulder) Triceps (back of arm) Latissimus Dorsi (mid back) Spinae Erectors (lower back) Gluteus Medius (hip) Gluteus Maximus (buttocks) Hamstring (back of leg) Gastrocnemius (back of calf) N N AA O O BB P P CC Q Q DD R R EE S S F F G G LL T T M M HH U U II V V JJ W W KK 12 MONDAY EXERCISE WEIGHT SETS REPS WEIGHT SETS REPS WEIGHT SETS REPS Date: / / AEROBIC EXERCISE TUESDAY Date: / / WEDNESDAY EXERCISE Date: / / THURSDAY AEROBIC EXERCISE Date: / / EXERCISE FRIDAY Date: / / Make photocopies of this page for scheduling and recording your workouts. 13 Part ListÑModel No. 831.150740 Key No. Qty. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 2 1 1 1 1 1 2 1 6 3 1 4 1 1 6 4 1 2 14 4 4 6 Description R0800A Key No. Qty. 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 # # 1 4 4 1 1 2 1 2 2 1 1 4 10 2 1 2 1 1 1 1 1 1 1 Upright Frame Crossbar Leg Lever Left Backrest Tube Backrest Upright Base Front Leg 3/4Ó Round Inner Cap Pad Tube Seat 1Ó Square Inner Cap M8 Nylon Locknut ÒUÓ Bracket M6 x 16mm Screw M6 x 38mm Screw M10 x 178mm Bolt M10 x 65mm Bolt M10 Nylon Locknut Support Plate 45mm Square Inner Cap Foam Pad Description 1Ó Round Inner Cap M10 Washer M6 Washer Curl Post Curl Pad Carriage Bushing 1Ó Angle Cap M10 x 67mm Adjustment Knob 60mm x 50mm Bushing Adjustment Pin M10 x 48mm Adjustment Knob M4 x 16mm Screw M10 x 81mm Bolt 1Ó x 2Ó Inner Cap Spacer M8 Washer M8 x 58mm Bolt M10 x 72mm Bolt Weight Tube Right Backrest Tube Pin Clip UserÕs Manual Exercise Poster Ò#Ó Indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover for information on ordering replacement parts. 14 Exploded DrawingÑModel No. 831.150740 R0800A 6 12 1 5 27 25 42 16 28 12 34 25 16 31 30 25 34 36 19 20 15 26 35 14 35 19 3 7 19 35 22 1 35 20 21 11 21 19 33 4 19 32 17 28 34 24 19 31 34 21 19 24 2 18 39 38 19 40 30 24 37 43 29 22 7 8 41 19 38 15 19 21 23 13 9 10 10 9 9 9 22 22 10 9 9 22 15 35 Model No. 831.150740 QUESTIONS? If you find that: The model number and serial number of your WEIDER¨ PRO800 are listed on a decal attached to the frame. See the front cover of this manual to find the location of the decal. ¥ a part is missing All replacement parts are available for immediate purchase or special order when you visit your nearest SEARS Service Center. To request service or to order parts by telephone, call the toll-free numbers listed at the left. ¥ or you need to schedule repair service When requesting help or service, or ordering parts, please be prepared to provide the following information: ¥ you need help assembling or operating the WEIDER¨ PRO800 call our toll-free HELPLINE 1-800-736-6879 ¥ The MODEL NUMBER of the product (831.150740) MondayÐSaturday, 7 amÐ7 pm Central Time (excluding holidays) ¥ The NAME of the product (WEIDER¨ PRO800 Weight Bench) REPLACEMENT PARTS ¥ The DESCRIPTION of the PART (see the PART LIST and the EXPLODED DRAWING on pages 14 and 15 of this manual). ¥ The PART NUMBER of the PART (see the PART LIST and the EXPLODED DRAWING on pages 14 and 15 of this manual) If parts become worn and need to be replaced, call the following tollfree number 1-800-FON-PART (1-800-366-7278) SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179 Full 90 Day Warranty For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this SEARS WEIGHT BENCH EXERCISER, contact the nearest SEARS Service Center throughout the United States and SEARS will repair or replace the WEIGHT BENCH EXERCISER, free of charge. This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for rental purposes. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179 Part No. 163192 R0800A Printed in China © 2000 Sears, Roebuck and Co.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 16 Create Date : 2000:11:14 15:52:16 Producer : Acrobat Distiller 3.02 for Power Macintosh Author : Dustin Lovell Creator : QuarkXPressª: PSPrinter 8.3.1 Title : *150740-163192EXIF Metadata provided by EXIF.tools