Weider Pro 800 Bench Webe1310 Users Manual

Weider-Webe13102-Owner-S-Manual weider-webe13102-owner-s-manual

2015-05-18

: Weider Weider-Pro-800-Bench-Webe1310-Users-Manual-733399 weider-pro-800-bench-webe1310-users-manual-733399 weider pdf

Open the PDF directly: View PDF .
Page Count: 16

Download
Open PDF In Browser	View PDF

Model No. WEBE13102
Serial No.

455
USER’S MANUAL

Write the serial number in the space
above for future reference.

Serial Number Decal (Under Seat)

QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if parts are
missing, we will guarantee complete satisfaction through direct
assistance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLLFREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:

1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST

CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.

Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!

TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
PART IDENTIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

WARNING DECAL PLACEMENT
The decal shown at the right has
been placed on the weight bench in
the indicated location. If the decal is
missing or illegible, please call our
Customer Service Department tollfree at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m.
Mountain Time, to order a free
replacement decal. Apply the
replacement decal in the location
shown.

WEIDER is a registered trademark of ICON Health & Fitness, Inc.

IMPORTANT PRECAUTIONS
WARNING:

To reduce the risk of serious injury, read the following important precautions before using the weight bench.
1. Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual.

partner should stand behind you to catch the
barbell if you cannot complete a repetition.
12. Always make sure that there is an equal
amount of weight on each side of your barbell while you are using it. When adding or
removing weights, always keep some weight
on both ends of the barbell and prevent the
barbell from tipping.

2. It is the responsibility of the owner to ensure
that all users of the weight bench are adequately informed of all precautions.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.

13. The weight bench is designed to support a
maximum of 560 pounds, including the user,
a barbell, and weights. Do not place more
that 310 pounds, including a barbell and
weights, on the weight rests. Do not place
more than 150 pounds on the leg lever.

4. Use the weight bench only on a level surface.
Cover the floor beneath the weight bench to
protect the floor.
5. Inspect and properly tighten all parts each
time you use the weight bench. Replace any
worn parts immediately.

14. Make sure that the adjustment knobs are
inserted completely and tightened into the
uprights before beginning any exercise.

6. Keep children under the age of 12 and pets
away from the weight bench at all times.

15. When adjusting the position of the seat,
make sure that the adjustment pin is inserted
through both adjustment tubes before beginning any exercise (see page 10).

7. Always wear athletic shoes for foot protection while exercising.
8. Keep hands and feet away from moving parts.

16. When you put weight on the weight rests,
make sure you put at least ten pounds on the
leg lever to balance the weight bench.

9. Do not use a barbell that is longer than six
feet with the weight bench. Note: The weight
bench does not include a barbell or weights.

17. Always remove the curl post from the front
leg before performing leg curls with the leg
lever.

10. When you are using the leg lever, place a
barbell with the same amount of weight on
the weight rests to balance the bench.

18. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling down.

11. Always exercise with a partner. When you
are performing bench press exercises, your

WARNING:

Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.

BEFORE YOU BEGIN
Thank you for selecting the WEIDER® PRO 455 weight
bench. The versatile PRO 455 weight bench is
designed to be used with your own weight set (not
included) to develop every major muscle group of the
body. Whether your goal is a shapely figure, dramatic
muscle size and strength, or a healthier cardiovascular
system, the PRO 455 weight bench will help you to
achieve the specific results you want.

toll-free at 1-800-999-3756, Monday through Friday, 6
a.m. until 6 p.m. Mountain Time (excluding holidays).
To help us assist you, please note the product model
number and serial number before calling. The model
number is WEBE13102. The serial number can be
found on a decal attached to the weight bench (see
the front cover of this manual).
Before reading further, please look at the drawing
below and familiarize yourself with the parts that are
labeled.

For your benefit, read this manual carefully before
using the weight bench. If you have additional questions, please call our Customer Service Department

Weight Rest

Adjustment Knob
Upright

Backrest

Curl Pad
Leg Lever

Weight Tube

Adjustment Tube
Seat

PART IDENTIFICATION CHART
This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below
each part refers to the key number of the part. Important: Some parts may have been pre-assembled for
shipping purposes. If you cannot find a part in the parts bags, check to see if it has been pre-assembled.

Spacer (37)
M10 x 81mm Bolt (35)

M10 x 68mm Bolt (44)

M8 Washer (38)

M10 x 65mm Bolt (18)

M10 Washer (24)

M8 x 58mm Bolt (39)

M6 x 38mm Screw (16)
M8 Nylon Locknut (13)

M6 x 16mm Screw (15)

M4 x 16mm Screw (34)

M10 Nylon Locknut (19)

M10 x 178mm Bolt (17)

M6 Washer (25)

M10 x 72mm Bolt (40)

ASSEMBLY
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.

Make Things Easier for Yourself
Everything in this manual is designed to ensure
that the weight bench can be assembled successfully by anyone. However, it is important to
realize that the versatile weight bench has
many parts and that the assembly process will
take time. Most people find that by setting aside
plenty of time, assembly will go smoothly.

• For help identifying small parts, use the PART
IDENTIFICATION CHART on page 5.
The following tools (not included) are required
for assembly:
• Two adjustable wrenches
• One rubber mallet

Before beginning assembly, carefully read the
following information and instructions:

• One standard screwdriver

• Assembly requires two people.

• One Phillips screwdriver

• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.

• Lubricant, such as grease or petroleum jelly,
and soapy water.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.

• Tighten all parts as you assemble them, unless
instructed to do otherwise.

1. Note: The parts shown in this step may be preassembled. Also, the Extension Tubes (43, see
step 2) may be slid onto the Crossbar (3).

Tab
34

Slide an Extension Tube Bushing (45) onto each
end of the Crossbar (3) as shown. Press a Crossbar
Bushing (46) into each end of the Crossbar. Secure
the two Crossbar Bushings with four M4 x 16mm
Screws (34).

Holes
34

45
46
34

Note: The tabs on the Extension Tube Bushings
(45) will need to be pushed into the holes in the
Crossbar (3) when the Extension Tubes (43, see
step 2) are slid onto the Crossbar.

45 Tab

3
34

2. The weight bench can be adjusted for use with
either a standard barbell (see drawing 2a) or an
Olympic barbell (see drawing 2b).

45
43

Warning
Decal

24
44

Note the position of the warning decal and make
sure that the Extension Tubes (43) are oriented
as shown. Slide an Extension Tube onto one end
of the Crossbar (3) and over an Extension Tube
Bushing (45). Align the indicated holes and secure
the Extension Tube to the Crossbar with two M10 x
68mm Bolts (44), two M10 Washers (24), and two
M10 Nylon Locknuts (19).

43
24
24

44
2b

Warning
Decal

24
44

43
24
44

Attach the other Extension Tube (43) to the other
end of the Crossbar (3) in the same manner.

3. Note: The following drawings show the
Crossbar (3) adjusted to the standard width.
Note the position of the warning decal and the
name decal, and make sure that the Extension
Tubes (43) and Upright Bases (7) are oriented
exactly as shown. Attach the Extension Tubes to
the Upright Bases with four M10 x 81mm Bolts
(35), two Support Plates (20), and four M10 Nylon
Locknuts (19).

19
20
43

Name
Decal
30
3

Slide the Uprights (1) into the Upright Bases (7)
and secure them at the desired height with the
M10 x 67mm Adjustment Knobs (30).

43 20 19
19

Warning Decal
35
20

WARNING: Always set both
Uprights (1) at the same height. Make sure
that the M10 x 67mm Adjustment Knobs (30)
are inserted completely and tightened into the
Uprights before you begin any exercise.

4
40
3

4. Attach the Frame (2) to the Crossbar (3) with two
M10 x 72mm Bolts (40) and two M10 Nylon
Locknuts (19).

5. Attach the Front Leg (8) to the Frame (2) with two
M10 x 65mm Bolts (18), two M10 Washers (24),
and two M10 Nylon Locknuts (19).

18
19

24
8

6. Tap three 45mm Square Inner Caps (21) into the
Leg Lever (4) as shown.

Insert the Weight Tube (41) into the indicated
hole in the Leg Lever (4). Tap a 1” Round Inner
Cap (23) into the indicated end of the Weight
Tube. Press a 1” Angle Cap (29) onto the other
end of the Weight Tube.

4
21
41
29
23

7. Lubricate an M10 x 72mm Bolt (40). Attach the
Leg Lever (4) to the Front Leg (8) with the Bolt
and an M10 Nylon Locknut (19).

19
4

Attach the Weight Tube (41) to the Leg Lever (4)
with the M8 x 58mm Bolt (39), two M8 Washers
(38), the Spacer (37), and an M8 Nylon Locknut
(13). Note: The Spacer will fit tightly inside of
the Leg Lever.

40
39
38

Lubricate
37

38
13

8. Press four 1” Square Inner Caps (12) into the
indicated ends of the Backrest Tubes (5, 42).
Press two 1” x 2” Inner Caps (36) into the ends of
the adjustment tubes.

8
6

Wide
End

With the wide end of the Backrest (6) positioned
as shown, attach the Backrest Tubes (5, 42) to
the Backrest with four M6 x 38mm Screws (16)
and four M6 Washers (25). Note: The Backrest
Tubes and Backrest must be oriented exactly
as shown.

5
16

Adjustment
Tubes

12
25
16

25
16

36
9. Lubricate the M10 x 178mm Bolt (17). Attach the
Backrest (6) to the Frame (2) with the Bolt, two
M10 Washers (24), and an M10 Nylon Locknut
(19).

Secure the Backrest (6) by sliding the Adjustment
Pin (32) through one of the three sets of holes in
the adjustment tubes and the indicated hole in the
Frame (2). Secure the Adjustment Pin with the
Pin Clip (14).

Adjustment
Tubes

Lubricate
24

Make sure the Adjustment Pin (32) is completely inserted through both holes in the
adjustment tubes and the Frame (2).

17
2

10. With the wide end of the Seat (11) positioned as
shown, attach the Seat to the brackets on the
Frame (2) with four M6 x 16mm Screws (15).

24
11
Wide
End

11. Attach the Curl Pad (27) to the Curl Post (26) with
two M6 x 16mm Screws (15).

27
15
26

12. Slide the Curl Post (26) into the Front Leg (8).
Align one of the adjustment holes in the Curl Post
with the adjustment hole in the Front Leg. Tighten
the M10 x 48mm Adjustment Knob (33) into the
adjustment hole in the Front Leg. Fully tighten
the Adjustment Knob.

26
33

13. Tap two 3/4” Round Inner Caps (9) into each Pad
Tube (10). Insert the Pad Tubes into the holes in
the Leg Lever (4) and the Front Leg (8). Slide two
Foam Pads (22) onto each Pad Tube.

13
22

9
9

22
9

14. Make sure that all parts are properly tightened
before you use the weight bench. The use of
all remaining parts will be explained in ADJUSTMENTS, beginning on page 10.

ADJUSTMENTS
The weight bench is designed to be used with your own weight set (not included). The steps below explain how
the weight bench can be adjusted. See EXERCISE GUIDELINES on page 12 for important exercise information
and refer to the accompanying exercise guide to see the correct form for several exercises. Refer also to the
exercise information accompanying your weight set for additional exercises.
Inspect and properly tighten all parts each time you use the weight bench. Replace any worn parts immediately.
The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ATTACHING WEIGHTS TO THE LEG LEVER
4

To use the Leg Lever (4), slide the desired weights
(not included) onto the Weight Tube (41).

WARNING:

Do not place more
than 130 pounds on the Leg Lever (4).
41

Weight
REMOVING THE PAD TUBE AND PADS
Before doing leg curl exercises, the indicated Pad
Tube (10) and Foam Pads (22) must be removed
from the weight bench. To do this, slide one of the
Foam Pads off of the Pad Tube; then pull the Pad
Tube out of the Front Leg (8).

22
10

22
ADJUSTING THE BENCH WIDTH
To adjust the width of the bench to use either a standard barbell or an Olympic barbell, remove the indicated M10 x 73mm Bolts (44) from the Extension
Tubes (43).

43
3
43

Refer to assembly steps 2 and 3 for instructions on
how to reassemble the Crossbar (3) at the desired
width.

ATTACHING THE CURL POST
For some exercises, the Curl Post (26) must be
attached to the weight bench.
Slide the Curl Post (26) into the Front Leg (8). Align
one of the adjustment holes in the Curl Post with the
adjustment hole in the Front Leg. Tighten the M10 x
48mm Adjustment Knob (33) into the adjustment hole
in the Front Leg. Make sure that you fully tighten
the Adjustment Knob.

21
26 33

Note: When the Curl Post (26) is not in use, the
45mm Square Inner Cap (21) should be inserted
into the Front Leg (8).

ADJUSTING THE UPRIGHTS
30

The Uprights (1) can be adjusted to five heights to
accommodate different exercises. To adjust the
height, remove the M10 x 67mm Adjustment Knobs
(30) from both Uprights and Upright Bases (7). Slide
the Uprights to the desired position and re-insert the
Adjustment Knobs.

1
7

WARNING:

Always set both
Uprights (1) at the same height. Make sure
that the Adjustment Knobs (30) are inserted
completely and tightened into the Uprights
before you begin any exercise.

30
7

ADJUSTING THE BACKREST
The Backrest (6) can be used in either a decline position, a level position, or two incline positions. To
adjust the Backrest to the decline position, remove
the Adjustment Pin (32) and lower the Backrest until it
rests directly on the Crossbar (3). Re-insert the
Adjustment Pin.

To adjust the Backrest (6) to the level position, insert
the Adjustment Pin (32) through the top set of holes
in the adjustment tubes and the Frame (2). Secure
the Adjustment Pin with the Pin Clip (14).

To adjust the Backrest (6) to an incline position, insert
the Adjustment Pin (32) through one of the lower two
sets of holes in the adjustment tubes and the Frame
(2). Secure the Adjustment Pin with the Pin Clip (14).

2
Adjustment
Tubes

WARNING:

When adjusting the
position of the Backrest (6), make sure that
the Adjustment Pin (32) is inserted through
both adjustment tubes and the Frame (2).

EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS

PERSONALIZING YOUR EXERCISE PROGRAM

Muscle Building
To increase the size and strength of your muscles,
push them close to their maximum capacity. Your
muscles will continually adapt and grow as you progressively increase the intensity of your exercise. You
can adjust the intensity level of an individual exercise
in two ways:
• by changing the amount of weight used
• by changing the number of repetitions or sets performed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)

Determining the exact length of time for each workout,
as well as the number of repetitions or sets completed, is an individual matter. It is important to avoid
overdoing it during the first few months of your exercise program. You should progress at your own pace
and be sensitive to your body’s signals. If you experience pain or dizziness at any time while exercising,
stop immediately and begin cooling down. Find out
what is wrong before continuing. Remember that adequate rest and a proper diet are important factors in
any exercise program.
WARMING UP

The proper amount of weight for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of weight that is
right for you. Begin with 3 sets of 8 repetitions for
each exercise you perform. Rest for 3 minutes after
each set. When you can complete 3 sets of 12 repetitions without difficulty, increase the amount of weight.

Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and delivering more oxygen to your muscles.
WORKING OUT

Toning
You can tone your muscles by pushing them to a
moderate percentage of their capacity. Select a moderate amount of weight and increase the number of
repetitions in each set. Complete as many sets of 15
to 20 repetitions as possible without discomfort. Rest
for 1 minute after each set. Work your muscles by
completing more sets rather than by using high
amounts of weight.

Each workout should include 6 to 10 different exercises. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.

Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.

EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise,
and moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompanying this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on page
13 to find the names of the muscles.

Cross Training
Cross training is an efficient way to get a complete
and well-balanced fitness program. An example of a
balanced program is:
• Plan weight training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
cycling or swimming, on Tuesday and Thursday.
• Rest from both weight training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.

The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath.

The combination of weight training and aerobic exercise will reshape and strengthen your body, and
develop your heart and lungs.

Rest for a short period of time after each set. The ideal
resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
• Rest for one minute after each set for a toning workout.
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
COOLING DOWN

slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout is
an effective way to increase flexibility.
STAYING MOTIVATED
For motivation, keep a record of each workout. List the
date, the exercises performed, the weight used, and
the numbers of sets and repetitions completed. Record
your weight and key body measurements at the end of
every month. Remember, the key to achieving the
greatest results is to make exercise a regular and
enjoyable part of your everyday life.

End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move

MUSCLE CHART
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
O.
P.
Q.
R.
S.
T.
U.
V.
W.

Sternomastoid (neck)
Pectoralis Major (chest)
Biceps (front of arm)
Obliques (waist)
Brachioradials (forearm)
Hip Flexors (upper thigh)
Abductor (outer thigh)
Quadriceps (front of thigh)
Sartorius (front of thigh)
Tibialis Anterior (front of calf)
Soleus (front of calf)
Rectus Abdominus (stomach)
Adductor (inner thigh)
Trapezius (upper back)
Rhomboideus (upper back)
Deltoid (shoulder)
Triceps (back of arm)
Latissimus Dorsi (mid back)
Spinae Erectors (lower back)
Gluteus Medius (hip)
Gluteus Maximus (buttocks)
Hamstring (back of leg)
Gastrocnemius (back of calf)

N
N

O
O

P
P

Q
Q

R
R

S
S
F
F
G
G

T
T

M
M

U
U

V
V

W
W

PART LIST—Model No. WEBE13102
Key No.

Qty.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

2
1
1
1
1
1
2
1
6
3
1
4
1
1
6
4
1
2
18
4
4
6
1
8

Description

R0902A

Key No.

Qty.

25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
#
#

4
1
1
2
1
2
2
1
1
8
8
2
1
2
1
3
1
1
2
4
2
2
1
1

Upright
Frame
Crossbar
Leg Lever
Right Backrest Tube
Backrest
Upright Base
Front Leg
3/4” Round Inner Cap
Pad Tube
Seat
1” Square Inner Cap
M8 Nylon Locknut
Pin Clip
M6 x 16mm Screw
M6 x 38mm Screw
M10 x 178mm Bolt
M10 x 65mm Bolt
M10 Nylon Locknut
Support Plate
45mm Square Inner Cap
Foam Pad
1” Round Inner Cap
M10 Washer

Description
M6 Washer
Curl Post
Curl Pad
Carriage Bushing
1” Angle Cap
M10 x 67mm Adjustment Knob
60mm x 50mm Bushing
Adjustment Pin
M10 x 48mm Adjustment Knob
M4 x 16mm Screw
M10 x 81mm Bolt
1” x 2” Inner Cap
Spacer
M8 Washer
M8 x 58mm Bolt
M10 x 72mm Bolt
Weight Tube
Left Backrest Tube
Extension Tube
M10 x 68mm Bolt
Extension Tube Bushing
Crossbar Bushing
User’s Manual
Exercise Guide

“#” Indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of
this manual for information on ordering replacement parts.

EXPLODED DRAWING—Model No. WEBE13102

R0902A

27
6
12

1
5

25
42
15
28

34
31

25
16

19
45

16
20

35
44
7

24
34

3
45

24
35

44
22
21

33
4
21

31
19
19

24
39

8
23

21
13

10
10

9
9

9
22

To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give the following information when calling:
• The MODEL NUMBER of the product (WEBE13102)
• The NAME of the product (WEIDER® PRO 455 weight bench)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING on pages 14 and 15)

LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center; products
used for commercial or rental purposes; or products used as store display models. No other warranty
beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813

Part No. 191040 R0902A

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2003:04:18 10:09:56
Producer                        : Acrobat Distiller 4.05 for Macintosh
Modify Date                     : 2003:04:18 10:10:00-06:00
Page Count                      : 16

EXIF Metadata provided by EXIF.tools

Weider Pro 800 Bench Webe1310 Users Manual

Weider-Webe13102-Owner-S-Manual weider-webe13102-owner-s-manual

Navigation menu

Versions of this User Manual:

Views

Navigation