Weider Pro 9400 Users Manual *WESY39100 167618

Weider-Pro-9400-System-Wesy3910-Users-Manual-734074 weider-pro-9400-system-wesy3910-users-manual-734074

Weider-Wesy39100-Owner-S-Manual weider-wesy39100-owner-s-manual

PRO 9400 to the manual 3a85a565-0430-4416-ada8-d9a0844d1776

2015-01-26

: Weider Weider-Pro-9400-Users-Manual-233625 weider-pro-9400-users-manual-233625 weider pdf

Open the PDF directly: View PDF PDF.
Page Count: 33

DownloadWeider Weider-Pro-9400-Users-Manual- *WESY39100-167618  Weider-pro-9400-users-manual
Open PDF In BrowserView PDF
Model No. WESY39100
Serial No.

USER'S MANUAL

Write the serial number in the
space above for reference.

Serial Number Decal (Under Seat)

QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you have
questions, or if there are missing
parts, we will guarantee complete
satisfaction through assistance
from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained technicians on our customer hot line
will provide immediate assistance, free of charge to you.
CUSTOMER HOT LINE:

1-800-999-3756
Mon.ÐFri., 6 a.m.Ð6 p.m. MST
Patent Pending

CAUTION
Read all precautions and instructions in this manual before using
this equipment. Save this manual
for future reference.

Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!

TABLE OF CONTENTS
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HOW TO USE THE HOME GYM SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
WEIGHT RESISTANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
TROUBLE-SHOOTING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
CABLE DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached at the center of
this manual. Remove the PART IDENTIFICATION CHART and the PART LIST/EXPLODED DRAWING before
beginning assembly.

WEIDER is a registered trademark of ICON Health & Fitness, Inc.

LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's option, the product at one of its authorized service centers. All
products for which warranty claim is made must be received by ICON at one of its authorized service centers with all freight and other transportation charges prepaid, accompanied by sufficient proof of purchase.
All returns must be pre-authorized by ICON. This warranty does not extend to any product or damage to
a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or
repairs not provided by an ICON authorized service center, products used for commercial or rental purposes, or products used as store display models. No other warranty beyond that specifically set forth
above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal, installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813

2

IMPORTANT PRECAUTIONS
WARNING:

To reduce the risk of serious injury, read the following important precautions
before using the home gym system.
8. Keep hands and feet away from moving parts.

1. It is the responsibility of the owner to ensure
that all users of the home gym system are
adequately informed of all precautions.

9. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cooling down.

2. The home gym system is intended for home
use only. do not use the home gym system in
an commercial, rental, or institutional setting.

10. Always wear athletic shoes for foot protection.

3. Read all instructions in this manual and in
the accompanying literature before using the
home gym system.

11. Always stand on a foot plate when performing an exercise that could cause the home
gym system to tip.

4. Use the home gym system only on a level
surface. Cover the floor beneath the home
gym system for protection.

12. Keep your hands away from the leg press
upright when the military press arm is being
used. Your hand could become pinched
between the leg press upright and military
press arm.

5. Inspect and tighten all parts often. Replace
any worn parts immediately.

13. Make sure that the cables remain on the pulleys at all times. If the cables bind while you
are exercising, stop immediately and make
sure that the cables are on all of the pulleys.

6. Keep children under the age of 12 and pets
away from the home gym system at all times.
7. Never release the press arm, butterfly arms,
military press arm, leg lever, leg press plate,
lat bar or nylon strap while weights are
raised. The weights will fall with great force.

14. Always disconnect the lat bar from the home
gym system when performing an exercise
that does not use the lat bar.

WARNING:

Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.

The warning decals shown below and at the right have been placed on the
home gym system in the locations shown on page 4. If a decal is missing or
illegible, please call our Customer Hot Line at 1-800-999-3759 and order a
free replacement decal. Place the decal on the home gym system in the location shown.
Warning Decal No. 1

¥ Keep clear of
this area.

3

Warning Decal No. 2

BEFORE YOU BEGIN
Thank you for selecting the versatile WEIDER¨ PRO
9400 home gym system. The PRO 9400 offers a
selection of weight stations designed to develop every
major muscle group of the body. Whether your goal is
to tone your body, build dramatic muscle size and
strength, or improve your cardiovascular system, the
PRO 9400 will help you to achieve the specific results
you want.

Customer Service Department toll-free at 1-800-9993756, Monday through Friday, 6 a.m. until 6 p.m.
Mountain Time (excluding holidays). To help us assist
you, please note the product model number and serial
number before calling. The model number is
WESY39100. The serial number can be found on a
decal attached to the home gym system (see the front
cover of this manual).

For your benefit, read this manual carefully before
using the WEIDER¨ PRO 9400 home gym system. If
you have additional questions, please call our

Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.

ASSEMBLED
DIMENSIONS:
Height: 76 in.
Width: 89 in.
Length: 64 in.

Lat Bar

High Pulley Station

Ab Pulley Station
Warning Decal
No. 2

Warning Decal No. 2
Military Press Arm
Backrests

Butterfly Arms
Press Arm
Warning
Decal No. 1

Leg Lever

Low Pulley
Station

Leg Press
Plate

Weight Stacks

Foot Plate

4

Warning Decal No. 1

ASSEMBLY
Before beginning assembly, carefully read the
following information and instructions:

¥ Assembly requires two persons. For your convenience and safety, assemble the home gym system with the help of another person.

¥ Due to the many features of the home gym
system, assembly will require about six hours. By
setting aside plenty of time and by deciding to
make the task enjoyable, assembly will go
smoothly. You may want to assemble the home
gym system over a couple of evenings.

¥ As you assemble the home gym system, be sure
that all parts are oriented as shown in the drawings.
THE FOLLOWING TOOLS (NOT INCLUDED) ARE
REQUIRED FOR ASSEMBLY:

¥ Place all parts of the home gym system in a
cleared area and remove the packing materials;
do not dispose of the packing materials until
assembly is completed.

¥ Two (2) adjustable wrenches
¥ One (1) standard screwdriver

¥ Assembly is divided into four stages: 1) frame
assembly, 2) press and butterfly arm assembly,
3) cable and pulley assembly, and 4) seat and
backrest assembly. The hardware for each stage
is packaged separately.

¥ One (1) phillips screwdriver

¥ Wait until you begin each assembly stage to open
the parts bag labeled for that assembly stage.

¥ Assembly will be more convenient if you have the
following tools: A socket set, a set of open-end or
closed-end wrenches, or a set of ratchet wrenches.

¥ One (1) rubber mallet
¥ Lubricant, such as grease or petroleum jelly,
and soapy water will also be needed.

¥ For help identifying the small parts used in
assembly, use the PART IDENTIFICATION
CHART located in the center of this manual.
Note: Some small parts may have been preattached for shipping. If a part is not in the parts
bag, check to see if it has been pre-attached.

Questions?
¥ If you have questions after reading the assembly
instructions, please call our Customer Service
Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain
Time.

¥ Tighten all parts as you assemble them, unless
instructed to do otherwise.

1. Before beginning assembly, be sure that
you have read and understand the information in the box above.

1

FRAME ASSEMBLY

11
Locate and open the parts bag labeled
ÒFRAME ASSEMBLY.Ó

51
8

5

Press two 2Ó Square Outer Caps (51) onto
the indicated locations on the Stabilizer (5).
Press a 2Ó Square Inner Cap (27) into the
end of the Base (4).

1

Insert six 5/16Ó x 2 1/2Ó Carriage Bolts (1) up
through the Stabilizer (5). Insert two 5/16Ó x
2 1/2Ó Carriage Bolts up through the Base (4).
51
Attach the Base (4) to the Stabilizer (5) with
two 5/16Ó x 2 3/4Ó Bolts (11), two 5/16Ó Flat
Washers (8), and two 5/16Ó Nylon Locknuts
(3). Do not tighten the Nylon Locknuts
yet.

5

1

3
4

1
27

2. Slide the Rear Upright (74) and the Leg Press
Upright (56) onto the indicated 5/16Ó x 2 1/2Ó
Carriage Bolts (1) in the Stabilizer (5). The
high side of the brackets on the Rear
Upright and Leg Press Upright should be
on the side shown. Hand tighten four 5/16Ó
Nylon Locknuts (3) onto the Carriage Bolts.
Do not tighten the Nylon Locknuts yet.

2

27
27

87

High Sides
of Brackets

91
74

Press a 2Ó Square Inner Cap (27) into the Leg
Press Upright (56). Press a 2Ó Square Inner
Cap into the Rear Upright (74).

56

Attach the Rubber Bumper (91) to the Leg
Press Upright (56) with the #8 x 1/2Ó Self-tapping Screw (87).
3

5

FRAME ASSEMBLY

1

1
3. Slide the Front Upright (42) onto the 5/16Ó x
2 1/2Ó Carriage Bolts (1) in the Base (4).
Hand tighten a 5/16Ó Nylon Locknut (3) onto
each Carriage Bolt. Do not tighten the
Nylon Locknuts yet.

3

Press a 1Ó Square Inner Cap (6) into the
Front Upright (42).

42
6
3
4
1

6

4. Press a 2Ó Square Inner Cap (27) into the end
of the Top Frame (55). Press a 1 3/4Ó Square
Inner Cap (44) into each end of the crossbar
on the Top Frame. Press two 1Ó Round Inner
Caps (75) into the top of the crossbar.

4

11

55

75
44

8
27

3

Attach the Top Frame (55) to the Rear Upright
(74) and the Leg Press Upright (56) with two
5/16Ó x 2 3/4Ó Bolts (11) and two 5/16Ó Nylon
Locknuts (3).

Crossbar

44

Attach the Top Frame (55) to the Front
Upright (42) with two 5/16Ó x 2 3/4Ó Bolts (11),
two 5/16Ó Flat Washers (8), and two 5/16Ó
Nylon Locknuts (3).

11

3

56

42

FRAME ASSEMBLY

74

5. Slide the Leg Press Seat Frame (79) onto the
indicated 5/16Ó x 2 1/2Ó Carriage Bolts (1) in
the Stabilizer (5). Hand tighten two 5/16Ó
Nylon Locknuts (3) onto the Carriage Bolts.

5

1
79
11
3

56

Attach the other end of the Leg Press Seat
Frame (79) to the Leg Press Upright (56) with
two 5/16Ó x 2 3/4Ó Bolts (11), two 5/16Ó Flat
Washers (8), and two 5/16Ó Nylon Locknuts (3).

8
3
3

Attach the Handle (82) to the Leg Press Seat
Frame (79) with two 5/16Ó x 2 1/2Ó Carriage
Bolts (1) and two 5/16Ó Nylon Locknuts (3).

82
1

5

Tighten all Nylon Locknuts used in steps
1Ð5.

6. Set two Weight Bumpers (19) on the bracket
on the Base (4) as shown. Set two Weight
Bumpers (19) on the bracket on the Stabilizer
(5).

6

Stack eight Weights (25) onto each set of
Weight Bumpers (19). Be sure that the pin
grooves are all on the same side of each
stack of Weights.

Pin
Grooves

25
25
Pin
Grooves

19
Be careful not to tip either stack of
Weights (25) until step 8 is complete.

5ÑBracket
19
4ÑBracket

7

7. Press a Weight Tube Bumper (64) into the
end of a Weight Tube (63). Insert the Weight
Tube into the front stack of Weights (25). Be
sure that the pin on the Weight Tube is sitting in the pin grooves in the top Weight.

7
Holes
62

Lubricate the inside of the holes in the Top
Weight (65). Set the Top Weight onto the front
stack of Weights (25). Insert both Long
Weight Guides (62) into the stack of Weights.
Be sure that the holes in the Weight
Guides are at the top, as shown.
65
Lubricate
Pin
63
64

FRAME ASSEMBLY

Pin Grooves

25
8. Press a Weight Tube Bumper (64) into the
end of the other Weight Tube (63). Insert the
Weight Tube into the rear stack of Weights
(25). Be sure that the pin on the Weight
Tube is sitting in the pin grooves in the top
Weight.
Lubricate the inside of the holes in the other
Top Weight (65). Set the Top Weight onto the
rear stack of Weights (25). Insert both Short
Weight Guides (73) into the stack of Weights.
Be sure that the holes in the Weight
Guides are at the top, as shown.

8

Holes
73

Lubricate
65
Pin
63
64
Pin Grooves

25

8

9. Attach the upper ends of the Short Weight
Guides (73) to the Top Frame (55) with a 5/16Ó
x 6Ó Bolt (60), two 1/2Ó x 3/4Ó Spacers (61), and
a 5/16Ó Nylon Locknut (3).

61

3 61
3

60

73

62

10. Locate and open the parts bag labeled
ÒARM ASSEMBLY.Ó

10

27

95

Welded
Tube

Be sure there is a Bushing (98) in each side of
the Stabilizer (5). Press a 2Ó Square Inner Cap
(27) into each end of the Leg Press Arm (96).

ARM ASSEMBLY

55

60

FRAME ASSEMBLY

Attach the upper ends of the Long Weight
Guides (62) to the Top Frame (55) with a 5/16Ó
x 6Ó Bolt (60), two 1/2Ó x 3/4Ó Spacers (61), and
a 5/16Ó Nylon Locknut (3).

9

97
96

Lubricate a 3/8Ó x 3 1/4Ó Bolt (67). Attach the
Leg Press Arm (96) to the Stabilizer (5) with the
Bolt and a 3/8Ó Nylon Locknut (21). Do not over
tighten the Nylon Locknut. The Leg Press
Arm must be able to pivot freely.
Align the welded tubes on the Leg Press Plate
(95) with one set of holes in the Leg Press Arm
(96). Attach the Leg Press Plate to the Leg
Press Arm with the Press Pin (97).

9

27
67ÑLubricate

5

27
98

11

17

11. Press a 1Ó x 7/8Ó Plastic Bushing (90) onto
each welded spacer on the Press Frame (17).
Slide the Press Frame into place onto the Base
(4). Note: This will be a tight fit. The Plastic
Bushings should fit on each end of the indicated tube in the Base. Make sure that the
pulleys are on the side shown.
Lubricate the 3/8Ó x 8Ó Bolt (59). Attach the
Press Frame (17) to the Base (4) with the Bolt
and a 3/8Ó Nylon Locknut (21).

21

Holes must
be on this
side
59ÑLubricate

21

Welded Spacers

4
Tube

90

12. Press a 1Ó Round Inner Cap (49) into one of
the Press Arms (46). Press a 1 3/4Ó Square
Inner Cap (44) into the Press Arm.

12

44

49

Attach the Press Arm (46) to one side of the
Press Frame (17) with two 5/16Ó x 2 1/2Ó Bolts
(22) and two 5/16Ó Nylon Locknuts (3).

46

22

Assemble the other Press Arm (46) in the
same manner.
46

3
17
13. Identify the Right Arm (48) and the Left Arm
(47). Note the position of the welded bracket
on each Arm. Arm identification is very
important for step 14.

50

31
50

Attach a ÒVÓ-Pulley (50) and a Long Cable
Trap (31) to the Right Arm (48) with a 3/8Ó x
2 1/2Ó Bolt (86) and a 3/8Ó Nylon Locknut (21).
Do not tighten the Nylon Locknut yet.

ARM ASSEMBLY

31

86

13

47

Welded
Brackets
21

Attach a ÒVÓ-Pulley (50) and a Long Cable
Trap (31) to the Left Arm (47) in the same
manner.

48

14. Lubricate both axles on the Top Frame (55).

14
55

Slide the Right Arm (48) onto the right axle.
Note: Be careful not to confuse the Right
Arm with the Left Arm (47); refer to step 13
to identify the Right Arm. Be sure that the
upper end of the Right Arm is behind the
indicated bracket on the Top Frame (55).
See the inset drawing. Tap two 1Ó Retainers
(69) and a 1Ó Round Cover Cap (70) onto the
axle. Be sure that the teeth on the
Retainers bend toward the Round Cover
Cap, as shown.

Bracket

47
Lubricate
Axle
48
69
45
70

Attach the Left Arm (47) in the same manner.
Press 1 3/4Ó Square Inner Caps (44) into the
lower ends of the Right and Left Arms (47,
48). Wet the lower end of each Arm with
soapy water. Slide a 10Ó Pad (45) onto the
lower end of each Arm.

44

44
45

Axle
69

70

10

15. See the inset drawing. Attach the Military
Press Arm (84) to the Pivot Arm (80) with two
5/16Ó x 2 1/4Ó Bolts (33) and two 5/16Ó Nylon
Locknuts (3).

ARM ASSEMBLY

Press two 1 1/2Ó Square Inner Caps (32) into
the indicated end of the Military Press Arm
(84). Press two 1Ó Round Inner Caps (49) into
the Military Press Arm.

15

32
49
32

21

84
80

Attach the Pivot Arm (80) to the Rear Upright
(74) with a 3/8Ó x 3 1/4Ó Bolt (67) and a 3/8Ó
Nylon Locknut (21).

67
74

56

33

80
84
3
16. Locate and open the parts bags labeled
ÒCABLE ASSEMBLYÓ and ÒPULLEYS.Ó

16

CABLE ASSEMBLY

23Ñ78.25Ó
During steps 16 through 36, refer to the
CABLE DIAGRAMS on pages 25Ð26 of this
manual to verify proper cable routing. Before
beginning this section, fully unwind the four
Cables. Identify the four Cables by comparing
the lengths and ends of the Cables. The
approximate length of each Cable is listed (in
inches) after the key number in the drawing.

58Ñ146.25Ó
72Ñ238.5Ó
78Ñ63.375Ó

IMPORTANT: While assembling the cables,
do not over tighten the bolts and nuts
attaching the pulleys. The pulleys must be
able to turn freely.
17. Locate the High Cable (58). Wrap the High
Cable around a 3 1/2Ó Pulley (15). Attach the
Pulley to the Top Frame (55) with a 3/8Ó x
3 3/4Ó Bolt (88) and a 3/8Ó Nylon Locknut (21).
Be sure that the end of the Cable with the
ball is on the indicated side of the Pulley
and that the Cable is between the Pulley
and the hook.

17

88
15

Ball
Hook

11

58

55

21

18. Wrap the High Cable (58) around a ÒVÓ-Pulley
(50). Attach the ÒVÓ-Pulley and a Long Cable
Trap (31) to the indicated bracket on the Front
Upright (42) with a 3/8Ó x 2 1/2Ó Bolt (86) and
a 3/8Ó Nylon Locknut (21). Be sure that the
Long Cable Trap is positioned to hold the
Cable in place.

18

86
31
58
50

Bracket
21
42
19. Route the High Cable (58) around the ÒVÓPulley (50) on the Left Arm (47). Be sure that
the Cable is in the groove of the Pulley
and that the Long Cable Trap (31) is positioned to hold the Cable in place. Tighten
the 3/8Ó x 2 1/2Ó Bolt (86) and the 3/8Ó Nylon
Locknut (not shown).

19
86

31

50

CABLE ASSEMBLY

58
47

20. Route the High Cable (58) around the ÒVÓPulley (50) on the Right Arm (48). Be sure
that the Cable is in the groove of the ÒVÓPulley and that the Long Cable Trap (31) is
turned to hold the Cable in place. Tighten
the 3/8Ó x 2 1/2Ó Bolt (86) and the 3/8Ó Nylon
Locknut (not shown).

20
31

86

58

21. Attach the Pulley Bracket (20) to the Top
Frame (55) with the 5/16Ó x 5Ó Bolt (68) and a
5/16Ó Nylon Locknut (3). Do not over tighten
the Nylon Locknut; the Pulley Bracket
must be able to move freely.
See the inset drawing. Route the High Cable
(58) around the 3 1/2Ó Pulley (15) attached to
the Pulley Bracket (20). Tighten the 3/8Ó x 2Ó
Bolt (12) and a 3/8Ó Nylon Locknut (not
shown). Be sure that the Cable is in the
groove of the Pulley and that the Cable
Trap (66) is turned to hold the Cable in
place.

12

21

50

48

68

55

66

20

12
15

3
58

22. See the inset drawing. Attach a 3 1/2Ó Pulley
(15) and a Cable Trap (66) to the upper hole in
a Long ÒUÓ-Bracket (57) with a 3/8Ó x 2Ó Bolt
(12) and a 3/8Ó Nylon Locknut (21). Be sure
that the Cable Trap is inside the Long ÒUÓBracket. Note: This may come pre-assembled.

22

58
66
21

Route the High Cable (58) through the Long
ÒUÓ-Bracket (57) and the 3 1/2Ó Pulley (15)
shown in the inset drawing. Be sure that the
Cable is in the groove of the Pulley and that
the Cable and Pulley move smoothly.

CABLE ASSEMBLY

23. Wrap the High Cable (58) around a 3 1/2Ó
Pulley (15). Attach the Pulley to the bracket on
the Top Frame (55) with a 3/8Ó x 2Ó Bolt (12)
and a 3/8Ó Nylon Locknut (21). Be sure that
the Cable is in the groove of the Pulley and
that the Cable and Pulley move smoothly.

15
15
12

57

58
57

23
Bracket
55

12
58
15

21
24. Attach the High Cable (58) to a Small ÒUÓBracket (71) with a 1/4Ó Nylon Locknut (2) and
a 1/4Ó Flat Washer (10). Do not completely
tighten the Nylon Locknut. It should be
threaded onto the end of the Cable only a
couple of turns, as shown in the inset drawing.

24

58

Attach the Small ÒUÓ-Bracket (71) to the indicated Weight Tube (63) with a 5/16Ó x 1 3/4Ó
Bolt (24) and a 5/16Ó Nylon Locknut (3).

3
24
71
63

10
71

58
10
2

13

2

25. Locate the Low Cable (23) and the bag
labeled ÒLOW PULLEY.Ó Route the Low
Cable under the 3 1/2Ó Low Pulley (76).
Attach the Pulley and the 5/8Ó x 9/16Ó Spacer
(7) to the Press Frame (17) with a 3/8Ó x 3
3/4Ó Bolt (88), 3/8Ó Flat Washer (9), and a 3/8Ó
Nylon Locknut (21). Be sure that the parts
are oriented as shown in the drawing, and
that the end of the Cable with the ball is on
the indicated side of the Press Frame
between the Pulley and the crossbar.

25

88
9
7
76
Ball

76

17

21
17

23
Crossbar

CABLE ASSEMBLY

26. Route the Low Cable (23) around a 3 1/2Ó
Pulley (15). Attach Pulley and a Cable Trap
(66) to the lower hole in the Front Upright (42)
with a 3/8Ó x 3 3/4Ó Bolt (88), a 3/8Ó Flat
Washer (9), and a 3/8Ó Nylon Locknut (21).
See the inset drawing. Be sure that the
Cable Trap is turned to hold the Cable in
place and that the Cable is routed around
the Pulley as shown.

26

23

15

42
66

21

21

15

66

42

Inset shows view
from other side
23
88 9

27. Route the Low Cable (23) around a 3 1/2Ó
Pulley (15). Attach the Pulley and a Cable
Trap (66) to the upper hole in the Press
Frame (17) with a 3/8Ó x 3 1/2Ó Bolt (16), a
3/8Ó Flat Washer (9), and a 3/8Ó Nylon
Locknut (21). Be sure that the Cable Trap is
turned to hold the Cable in place and that
the Cable is routed around the Pulley as
shown.

27
23

16
15
17
21

28. Route the Low Cable (23) around another 3
1/2Ó Pulley (15). Attach the Pulley and a
Cable Trap (66) to the upper hole in the Front
Upright (42) with a 3/8Ó x 3 3/4Ó Bolt (88), a
3/8Ó Flat Washer (9), and a 3/8Ó Nylon
Locknut (21). See the inset drawing. Be
sure that the Cable Trap is turned to hold
the Cable in place and that the Cable is
routed around the Pulley as shown.

28

66

23

42
23
66

21

15

9

15

88
42

88

14

9

66

Inset shows view
from other side

29. Attach the end of the Low Cable (23) to the
Long ÒUÓ-Bracket (57) with a 1/4Ó Nylon
Locknut (2) and a 1/4Ó Flat Washer (10).

29

You may need to lift the Top Weight (not
shown) on the High Cable to get enough
slack to attach the Low Cable to the Long
ÒUÓ-Bracket.

57

2

Do not completely tighten the Nylon
Locknut (2). It should be threaded onto the
end of the Cable so only a couple of
threads are showing above the Nylon
Locknut, as shown in the inset drawing.

2

10
23

10
57

23
30

72

CABLE ASSEMBLY

30. Locate the Military Press Cable (72). Attach
the Military Press Cable to the other Small
ÒUÓ-Bracket (71) with a 1/4Ó Nylon Locknut (2)
and a 1/4Ó Flat Washer (10). Do not completely tighten the Nylon Locknut. It
should be threaded onto the end of the
Cable only a couple of turns, as shown in
the inset drawing.

3
71
24
63
10

72

71

2

Attach the Small ÒUÓ-Bracket (71) to the indicated Weight Tube (63) with a 5/16Ó x 1 3/4Ó
Bolt (24) and a 5/16Ó Nylon Locknut (3).

10
2

31. Wrap the Military Press Cable (72) around a
3 1/2Ó Pulley (15). Attach the Pulley to the Top
Frame (55) with a 3/8Ó x 2Ó Bolt (12) and a
3/8Ó Nylon Locknut (21).

31

See the inset drawing. Wrap the Military
Press Cable (72) around a 3 1/2Ó Pulley (15).
Attach the Pulley and a Cable Trap (66) to the
bracket on the Stabilizer (5) with a 3/8Ó x 2Ó
Bolt (12) and a 3/8Ó Nylon Locknut (21). Be
sure that the Cable Trap is turned to hold
the Cable in place.

21

55
15
12
72

72
12
Bracket
66
15
21
5

15

32. Wrap the Military Press Cable (72) around a 3
1/2Ó Pulley (15). Attach the Pulley and a
Cable Trap (66) to the Pivot Arm (80) with the
3/8Ó x 5Ó Bolt (101). Be sure the Bolt is on
the side shown, and that the Cable Trap is
positioned to hold the Cable in place. Do
not attach a locknut yet.

32

101

66

15
80

72

CABLE ASSEMBLY

See the inset drawing. Wrap the Military
Press Cable (72) around a 3 1/2Ó Pulley (15).
Attach the Pulley and a Cable Trap (66) to the
upper hole in the Long ÒUÓ-Bracket (57) with a
3/8Ó x 2Ó Bolt (12) and a 3/8Ó Nylon Locknut
(21). Be sure that the Cable Trap is inside
the Long ÒUÓ-Bracket, the Cable is in the
groove of the Pulley, and that the Cable
and Pulley move smoothly.

66
21

57

15

Wrap the Military Press Cable (72) around
another 3 1/2Ó Pulley (15). Attach the Pulley
and a Cable Trap (66) to the Pivot Arm (80)
on the other side of the 3/8Ó x 5Ó Bolt (101),
with a 3/8Ó Nylon Locknut (21). Be sure that
the Cable Trap is positioned to hold the
Cable in place, and that the Cable is routed as shown.

66

21

12

57

33. Wrap the Military Press Cable (72) around a 3
1/2Ó Pulley (15). Attach the Pulley and a
Cable Trap (66) to the Leg Press Upright (56)
with a 3/8Ó x 2Ó Bolt (12) and a 3/8Ó Nylon
Locknut (21). Be sure the Cable Trap is
positioned to hold the Cable in place.

33

56

21

66

72
15
12

34. Lay the Military Press Cable (72) over a 3 1/2Ó
Pulley (15). Attach the Pulley and both Pulley
Covers (77) to the Leg Press Upright (56) with
a 3/8Ó x 3 3/4Ó Bolt (88), two 3/8Ó Flat
Washers (9), and a 3/8Ó Nylon Jam Nut (99).

34
72

99
9
Post

15

Make sure that the Cable (72) is between
the Pulley (15) and the post. Be sure that
the Cable and Pulley move smoothly.

Large tabs
must be in
this location

77
9

The Pulley Covers (77) must be turned so
that the large tabs face toward the weight
system. See the inset drawing.

56

16

88

35. Locate the Leg Press Cable (78). Attach the
end of the Leg Press Cable to the Long ÒUÓBracket (57) with a 1/4Ó Nylon Locknut (2) and
a 1/4Ó Flat Washer (10). Do not completely
tighten the Nylon Locknut. It should be
threaded onto the end of the Cable only a
couple of turns, as shown in the inset
drawing.

35

2
Wrap the Leg Press Cable (78) around a
3 1/2Ó Pulley (15). Attach the Pulley to the Leg
Press Upright (56) with the 3/8Ó x 3 3/4Ó Bolt
(88), a 3/8Ó Flat Washer (9), and a 3/8Ó Nylon
Locknut (21). Be sure that the Cable and
Pulley move smoothly and that the Cable
is between the Pulley and the welded rod.
The ball on the Cable must be on the indicated side of the Pulley.

56
10

Ball

57
15

88

9
21

78

CABLE ASSEMBLY

Welded
Rod

2
10
78
36. Attach the Press Bracket (94) to the Leg
Press Arm (96) with a 3/8Ó x 3Ó Bolt (100) and
a 3/8Ó Nylon Jam Nut (99).

57

36

Wrap the Leg Press Cable (78) around a 3 1/2Ó
Pulley (15). Attach the Pulley to the Press
Bracket (94) with a 3/8Ó x 2Ó Bolt (12) and a
3/8Ó Nylon Locknut (21).
Slide a 5/16Ó Flat Washer (8) onto a 5/16Ó x
2 3/4Ó Bolt (11). Insert the Bolt through the
center hole in the Leg Press Seat Frame (79)
from the indicated side. (Note: The three
holes are for cable adjustment.) Tighten a
5/16Ó Flat Washer (8) and a 5/16Ó Nylon Jam
Nut (93) onto the Bolt. Slide the end of the
Leg Press Cable (78) onto the end of the Bolt.
Thread another 5/16Ó Nylon Jam Nut (93)
onto the Bolt. Do not fully tighten the second Jam Nut. There must be room
between the two Jam Nuts for the end of
the Cable to pivot.

17

96
99

11
8

78

12

94

15
8

100

21

79
93

37. Locate and open the parts bag labeled
ÒSEAT ASSEMBLY.Ó

37

85
56

Insert a 1/4Ó x 2 1/2Ó Carriage Bolt (92)
through the center hole in a Seat Plate (37).
Attach the Seat Plate to the Leg Press
Backrest (85) with two 1/4Ó x 1/2Ó Screws (18).

18

Insert the 1/4Ó x 2 1/2Ó Carriage Bolt (92)
through the indicated hole in the Leg Press
Upright (56). Tighten a 1/4Ó Nylon Locknut (2)
with a 1/4Ó Flat Washer (10) onto the Carriage
Bolt. Attach the top of the Leg Press Backrest
(85) to the Leg Press Upright with a 1/4Ó x 2
1/2Ó Screw (43) and a 1/4Ó Flat Washer (10).

37 92

10
43

2
38

13

SEAT ASSEMBLY

38. Attach one end of a Seat (13) to the Leg
Press Seat Frame (79) with two 1/4Ó x 1/2Ó
Screws (18). Attach the other end of the Seat
to the Leg Press Seat Frame with a 1/4Ó Flat
Washer (10) and a 1/4Ó x 2 1/2Ó Screw (43).

18

10
43
39. Attach the Front Backrest (41) to the Front
Upright (42) with two 1/4Ó x 2 1/2Ó Screws
(43) and two 1/4Ó Flat Washers (10).

39

79

42

41

43 10

Thick
End

40. Press a 1 1/2Ó Square Inner Cap (32) into the
Front Seat Frame (36).
Insert a 1/4Ó x 2Ó Carriage Bolt (38) through
the center hole in the Seat Plate (37). Attach
the Seat Plate to the Seat (13) with two 1/4Ó x
3/4Ó Screws (18).

40
13

38

Insert the 1/4Ó x 2Ó Carriage Bolt (38) through
the indicated hole in the Front Seat Frame
(36). Tighten a 1/4Ó Nylon Locknut (2) with a
1/4Ó Flat Washer (10) onto the Carriage Bolt.
Attach the other end of the Seat (13) to the
Front Seat Frame (36) with a 1/4Ó Flat
Washer (10) and a 1/4Ó x 2Ó Machine Screw
(81).

37
32

18

36
81

18

10

2

41. Press a 1 1/2Ó Square Inner Cap (32) into the
Leg Lever (29).

41

Lubricate the 5/16Ó x 2 1/4Ó Bolt (33). Attach
the Leg Lever (29) to the Front Seat Frame
(36) with the Bolt and a 5/16Ó Nylon Locknut
(3).

36
3

33

Insert the 5/16Ó x 2Ó Eyebolt (35) into the Leg
Lever (29) from the direction shown. Tighten a
5/16Ó Nylon Locknut (3) with a 5/16Ó Flat
Washer (8) onto the Eyebolt.

29
8

35

3
32
42. Rest the Front Seat Frame (36) on the indicated pin in the Front Upright (42). Attach the
Front Seat Frame to the Front Upright with a
5/16Ó x 2 3/4Ó Carriage Bolt (14), 3/16Ó Flat
Washer (8), and the Seat Knob (40).

42
42

40
8

SEAT ASSEMBLY

14

36

Pin

43. Press two 3/4Ó Round Inner Caps (34) into
each Pad Tube (28).

43

Insert a Pad Tube (28) into the Front Seat
Frame (36). Slide a Foam Pad (30) onto each
end of the Pad Tube.
Insert the other Pad Tube (28) into the Leg
Lever (29). Slide a Foam Foam Pad (30) onto
each end of the Pad Tube.
34
28
29
30

19

34

30

44. Remove the adhesive backing from the PRO 9400 decal and apply it to the Front Upright (42) under the
ÒWEIDERÓ nameplate as shown.
44

PRO 9400
Decal
42

SEAT ASSEMBLY

42

45. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in
HOW TO USE THE HOME GYM SYSTEM, beginning on page 21 of this manual.
Before using the home gym system, pull each cable a few times to be sure that the cables move smoothly
over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If
the cables are not properly installed, they may be damaged when heavy weight is used. See the
CABLE DIAGRAMS on page 25 and 26 of this manual for proper cable routing. If there is any slack
in the cables, you will need to remove it by tightening the cables. See TROUBLE-SHOOTING AND
MAINTENANCE on page 24.

20

HOW TO USE THE HOME GYM SYSTEM
The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise
poster accompanying this manual to see how the home gym system should be set up for each exercise.
IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments are in the correct starting position for the exercise to be performed. If there is any slack in the cables or chain as an
exercise is performed, the effectiveness of the exercise will be reduced.
CHANGING THE WEIGHT SETTING
The home gym system features two weight stacks.
The front weight stack is connected to the upper and
lower pulleys, the press arm, and the butterfly arms.
The rear weight stack is connected to the military
press arm and leg press.

26

To change the weight setting of either weight stack,
insert a Weight Pin (26) under the desired Weight
(25). Insert the Weight Pin until the bent end of the
Weight Pin is touching the Weights, and turn the bent
end downward. The weight setting of either weight
stack can be changed from 6.5 pounds to 106.5
pounds, in increments of 12.5 pounds. Note: Due to
the cables and pulleys, the amount of resistance
at each exercise station may vary from the weight
setting. Use the WEIGHT RESISTANCE CHART on
page 23 to find the approximate amount of resistance at each weight station.

25
26

ATTACHING THE LAT BAR OR NYLON STRAP TO
THE HIGH PULLEY STATION
53

Attach the Lat Bar (54) to the High Cable (58) with a
Cable Clip (53). For some exercises, the Chain (52)
should be attached between the Lat Bar and the High
Cable with two Cable Clips. Adjust the length of the
Chain between the Lat Bar and the High Cable so
the Lat Bar is in the correct starting position for
the exercise to be performed.

52
58

53
54

The Nylon Strap (39) can be attached in the same
manner.

39

ATTACHING THE LAT BAR OR NYLON STRAP TO
THE LOW PULLEY STATION

23
53

Attach the Lat Bar (54) to the Low Cable (23) with a
Cable Clip (53). For some exercises, the Chain (52)
should be attached between the Lat Bar and the Low
Cable with two Cable Clips. Adjust the length of the
Chain between the Lat Bar and the Low Cable so
the Lat Bar is in the correct starting position for
the exercise to be performed.

52
53

39

The Nylon Strap (39) can be attached in the same
manner.

54

21

ATTACHING AND REMOVING THE SEAT

8

To attach the Seat (13), set the bracket on the Front
Seat Frame (36) onto the indicated pins on the Front
Upright (42). Attach the Seat Frame to the Front
Upright with the 5/16Ó x 2 3/4Ó Carriage Bolt (14),
3/16Ó Flat Washer (8) and the Seat Knob (40).

40
36

13

42
For some exercises, the Seat (13) must be removed.
First, be sure that the chain is not attached to the leg
lever. Next, remove the Seat Knob (40), 3/16Ó Flat
Washer (8) and the 5/16Ó x 2 3/4Ó Carriage Bolt (14)
from the Front Seat Frame (36). Lift the Front Seat
Frame off the Front Upright (42).

14

Pin

ATTACHING THE LEG LEVER TO THE LOW
PULLEY STATION
To use the Leg Lever (29), the seat must be attached
to the Front Upright (42) (see ATTACHING AND
REMOVING THE SEAT above).

53

Attach one end of the Chain (52) to the Low Cable
(23) with a Cable Clip (53). Attach the other end of
the Chain to the Eyebolt (35) with a Cable Clip.

42

29
35

52

53
23

ADJUSTING THE LEG PRESS PLATE
Remove the Press Pin (97) from the Leg Press Plate
(95) and the Leg Press Arm (96).

95

Welded
Tube

Align the welded tubes on the Leg Press Plate (95)
with the desired set of holes in the Leg Press Arm
(96). Re-insert the Press Pin (97) through the welded
tubes on Leg Press Plate and the holes in the Leg
Press Arm.

97

96

22

WEIGHT RESISTANCE CHART
This chart shows the approximate weight resistance at each weight station. ÒTopÓ refers to the 6.5 lb. top weight.
The other numbers refer to the 12.5 lb. weight plates. The butterfly arm resistance listed is the resistance for
each butterfly arm. The actual resistance at each weight station may vary due to differences in individual
weight plates, as well as friction between the cables, pulleys, and weight guides.

WEIGHT

PRESS
ARM

BUTTERFLY
ARM

LEG
LEVER

HIGH
PULLEY

LOW
PULLEY

MILITARY
PRESS ARM

LEG
PRESS

AB
STATION

PLATES

(lbs.)

(lbs.)

(lbs.)

(lbs.)

(lbs.)

(lbs.)

(lbs.)

(lbs.)

Top

20

10

15

16

30

46

40

30

1

45

22

36

30

60

72

80

45

2

70

33

54

52

100

97

146

59

3

99

42

75

68

130

122

166

74

4

128

48

96

87

170

147

210

88

5

153

60

115

100

200

172

240

103

6

184

69

137

120

255

198

268

117

7

204

79

146

135

270

223

325

132

8

247

91

176

155

320

248

360

147

23

TROUBLE-SHOOTING AND MAINTENANCE
Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. The
home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents.
TIGHTENING THE CABLES
Woven cable, the type of cable used on the home gym system, can stretch slightly when it is first used. If there
is slack in the cables before resistance is felt, the cables should be tightened. If any slack is felt when using the
front weight stack, both the High Cable (58) and the Low Cable (23) will need to be tightened. If any slack is felt
when using the rear weight stack, both the Military Press Cable (72) and the Leg Press Cable (78) will need to
be tightened.
To tighten the cables, insert the weight pin into the middle of
the weight stack. Slack can be removed from these cables
several ways:
¥

1
15

66

See drawing 1. Tighten the 1/4Ó Nylon Locknut (2) that
connects the end of the Low Cable (23) to the Long ÒUÓBracket (57).

21
12

57
The Leg Press Cable (78) can be tightened in the same
manner.
2
¥

See drawing 1. Remove the 3/8Ó Nylon Locknut (21) and
the 3/8Ó x 2Ó Bolt (12) from the Cable Trap (66), 3 1/2Ó
Pulley (15), and Long ÒUÓ-Bracket (57). Re-attach the
Pulley and Cable Trap to the other hole in the Long ÒUÓBracket. Be sure that the Cable Trap is in the proper
position and that the Cable and Pulley move smoothly.

2

23 or 78

72

58

71
2

The other Long ÒUÓ-Bracket (57) can be adjusted in the
same manner.
¥

71
2

See drawing 2. Tighten the 1/4Ó Nylon Locknut (2) that
connects the end of the High Cable (58) to the Small ÒUÓBracket (71).
3
The Military Press Cable (72) can be tightened in the
same manner.

¥

See Drawing 3. If additional slack is felt while using the
Leg Press Arm, then the end of the Leg Press Cable (78)
must be moved to the next hole in the Leg Press Seat
Frame (79). Remove the 5/16Ó x 2 3/4Ó Bolt (11), the two
5/16Ó Flat Washers (8), the end of the Cable, and both
5/16Ó Nylon Jam Nuts (93) from the Leg Press Seat
Frame. Re-attach the Bolt, the Washer, the end of the
Cable, and both Nylon Jam Nuts to the next hole in the
Leg Press Seat Frame.

11

96
8
8
78
93

79

93

Do not over tighten the cables. The top weight will be lifted off the weight stack.
If a cable tends to slip off the pulleys often, it may have become twisted. Remove the cable and re-install it.
If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual.

24

CABLE DIAGRAMS
The cable diagrams on these pages show the proper routing of the High Cable (58), the Low Cable (23), the
Military Press Cable (72), and the Leg Press Cable (78). Use the diagrams to be sure that the four cables and
the cable traps have been assembled correctly. If the cables have not been correctly routed, the home gym system will not function properly and damage may occur. The insets show the proper positioning of the cable traps.
The cable traps should be positioned so that the cables will not come off the pulleys. Be sure that the cable
traps do not touch or bind the cables.
High Cable (58) and Low Cable (23)

3

2

1ÑHigh Pulley

7
5
4

TOP VIEW
6

High Cable (58)

5ÑLong ÒUÓ-Bracket

Low Cable (23)

Front Weight StackÑ8
4
3

2

25

1ÑLow Pulley

Military Press Cable (72) and Leg Press Cable (78)

2

Military Press Cable (72)

Ball End
6

8

4

7

1ÑLong ÒUÓ-Bracket

5

3

2

Rear Weight StackÑ1

4ÑRear Seat Frame
3

Leg Press Cable (78)

26

NOTES

27

1/4" Nylon Locknut (2)
1/4" x 2" Machine Screw (81)
5/16" Nylon Locknut (3)

5/16" Nylon Jam Nut (93)

3/8" Nylon Jam Nut (99)

5/16" x 2 1/2" Bolt (22)

3/8" x 2" Bolt (12)

3/8" Nylon Locknut (21)
5/16" x 2 1/4" Bolt (33)

1/4" Flat Washer (10)
1/4" x 2 1/2" Screw (43)

5/16" Flat Washer (8)
5/16" x 2 1/2" Carriage Bolt (1)

3/8" Flat Washer (9)
3/8" x 2 1/2" Bolt (86)

5/16" x 1 3/4" Bolt (24)

1/4" x 2" Carriage Bolt (38)

1/4" x 2 1/2" Carriage Bolt (92)

5/16" x 2 3/4" Bolt (11)

5/16" x 2 3/4" Carriage Bolt (14)

3/8" x 3" Bolt (100)

1/4" x 3/4" Screw (18)

3/8" x 3 1/4" Bolt (67)

#8 x 1/2" Self-tapping Screw (87)
3/8" x 3 1/2" Bolt (16)

3/8" x 3 3/4" Bolt (88)

5/16" x 5" Bolt (68)

1 1/8" x 2 1/2" Plastic Bushing (89)

1" x 7/8" Plastic Bushing (90)
3 1/2" Pulley (15)
(Not shown to scale)
"V"-Pulley (50)
(Not shown to scale)

5/16" x 6" Bolt (60)

3/8" x 5" Bolt (101)

1" Retainer (69)

3/8" x 8" Bolt (59)

Cable Clip (53)

1/2" x 3/4" Spacer (61)
5/16" x 2" Eyebolt (35)

3/4" Round Inner Cap (34)
1" Round Inner Cap (49)
1" Round Cover Cap (70)

1" Square Inner Cap (6)

1 3/4" Square Inner Cap (44)

1 1/2" Square Inner Cap (32)

2" Square Inner Cap (27)

2" Square Outer Cap (51)

PART LISTÑModel No. WESY39100
Key No.

Qty.

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52

10
6
31
1
1
1
1
10
7
11
9
8
2
1
16
1
1
6
4
1
21
4
1
2
16
2
8
2
1
4
3
4
3
4
1
1
2
1
1
1
1
1
4
6
2
2
1
1
4
3
2
1

Description
5/16Ó x 2 1/2Ó Carriage Bolt
1/4Ó Nylon Locknut
5/16Ó Nylon Locknut
Base
Stabilizer
1Ó Square Inner Cap
5/8Ó x 9/16Ó Spacer
5/16Ó Flat Washer
3/8Ó Flat Washer
1/4Ó Flat Washer
5/16Ó x 2 3/4Ó Bolt
3/8Ó x 2Ó Bolt
Seat
5/16Ó x 2 3/4Ó Carriage Bolt
3 1/2Ó Pulley
3/8Ó x 3 1/2Ó Bolt
Press Frame
1/4Ó x 3/4Ó Screw
Weight Bumper
Pulley Bracket
3/8Ó Nylon Locknut
5/16Ó x 2 1/2Ó Bolt
Low Cable
5/16Ó x 1 3/4Ó Bolt
Weight
Weight Pin
2Ó Square Inner Cap
Pad Tube
Leg Lever
Foam Pad
Long Cable Trap
1 1/2Ó Square Inner Cap
5/16Ó x 2 1/4Ó Bolt
3/4Ó Round Inner Cap
5/16Ó x 2Ó Eyebolt
Front Seat Frame
Seat Plate
1/4Ó x 2Ó Carriage Bolt
Nylon Strap
Seat Knob
Front Backrest
Front Upright
1/4Ó x 2 1/2Ó Screw
1 3/4Ó Square Inner Cap
10Ó Pad
Press Arm
Left Arm
Right Arm
1Ó Round Inner Cap
ÒVÓ-Pulley
2Ó Square Outer Cap
Chain

R0900A

Key No.

Qty.

53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
#
#

3
1
1
1
2
1
1
2
4
2
2
2
2
10
2
1
4
2
2
1
2
1
2
1
2
1
1
1
1
1
8
1
1
3
1
6
2
2
1
1
2
1
1
1
1
2
2
1
1
1
1

Description
Cable Clip
Lat Bar
Top Frame
Leg Press Upright
Long ÒUÓ-Bracket
High Cable
3/8Ó x 8Ó Bolt
5/16Ó x 6Ó Bolt
1/2Ó x 3/4Ó Spacer
Long Weight Guide
Weight Tube
Weight Tube Bumper
Top Weight
Cable Trap
3/8Ó x 3 1/4Ó Bolt
5/16Ó x 5Ó Bolt
1Ó Retainer
1Ó Round Cover Cap
Small ÒUÓ-Bracket
Military Press Cable
Short Weight Guide
Rear Upright
1Ó Inner Cap
3 1/2Ó Low Pulley
Pulley Cover
Leg Press Cable
Leg Press Seat Frame
Pivot Arm
1/4Ó x 2Ó Machine Screw
Handle
5Ó Plastic Grip
Military Press Arm
Leg Press Backrest
3/8Ó x 2 1/2Ó Bolt
#8 x 1/2Ó Self-tapping Screw
3/8Ó x 3 3/4Ó Bolt
1 1/8Ó x 2 1/2Ó Plastic Bushing
1Ó x 7/8Ó Plastic Bushing
Rubber Bumper
1/4Ó x 2 1/2Ó Carriage Bolt
5/16Ó Nylon Jam Nut
Press Bracket
Leg Press Plate
Leg Press Arm
Press Pin
Bushing
3/8Ó Nylon Jam Nut
3/8Ó x 3Ó Bolt
3/8Ó x 5Ó Bolt
UserÕs Manual
Exercise Poster

Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice.

10

2

21

3

74

27

57

83

78

15

11

12

66

54

51

52

5

11

10
2

65

8

51

25

26

11

3

60

1

53

19

61

64
12

15

21

39

83

66

3

2

88

1

15

10

10

3

8

21

43

91

87

99 9

3

24

27

11 8

63

71

72

73

3

21

21

9

1

83

67

80

66

82

11

81

101
15

12

66 11
15

15
88

92
77
9

11

37

18

56

27

3

10
43
3

18

66

3

33

93

15

83

83

79

8

21

84

49

32

21

94

96

15 66

12 99
78 15

21

13

18

3

98

85

20

10

2

21

32

27

57

66
12

67

27

15

21

95

27

23

15

83

100
21

12

3

68

97

55

25

2

3
10

60

27

3

21

12

EXPLODED DRAWINGÑModel No. WESY39100

61

19

4

64

65

24

71

63

75

44

58

62

3

8

11

1

26

88

43

3

15

3

9

21

75 44

10

12

R0900A

42

21

50

88

86

3

27

15

31

15

49

6

66

14

41

44

83

34

21

37

30

33

18

17

21

22

34

35

2

13

70

30

10

38

45

44

48

69

89

46

21

81

66

36

40
8

58

50

31

86

3

32

8

29

32

70

90

21

66

3

28
3

30

34

45

44

7

76

88

49

23

44

47

16

59

15

9

46

34
30

83

28

69

89

ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be prepared to give the following information:
1. The MODEL NUMBER of the product (WESY39100).
2. The NAME of the product (WEIDER¨ PRO 9400 home gym system).
3. The SERIAL NUMBER of the product (see the front cover of this manual).
4. The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING
attached at the center of this manual).

Part No. 167618 R0900A

Printed in Canada © 2000 ICON Health & Fitness, Inc.



Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 33
Create Date                     : 2000:11:21 16:08:55
Producer                        : Acrobat Distiller 3.02 for Power Macintosh
Author                          : Steve Slade
Creator                         : QuarkXPressª: PSPrinter 8.3.1
Title                           : *WESY39100-167618
EXIF Metadata provided by EXIF.tools

Navigation menu