Weifang Goertek Electronics G015B Bluetooth wireless headset User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3584513
Application ID	a6v7ZduAKNj+1PQ9i43j+w==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	Yes
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.2kB (127476 bits)
Date Submitted	2017-09-28 00:00:00
Creation Date	0000-00-00 00:00:00
Producing Software	Skia/PDF m63
Document Lastmod	0000-00-00 00:00:00
Document Title	Users Manual

Required​ ​Safety​ ​Statement
This​ ​page​ ​provides​ ​important​ ​safety​ ​and​ ​regulatory​ ​information​ ​that​ ​you​ ​should
read​ ​before​ ​you​ ​start​ ​using​ ​your​ ​device.
Safety​ ​Warnings
WARNING:​ ​HEALTH​ ​AND​ ​SAFETY​ ​INFORMATION;​ ​READ​ ​BEFORE​ ​USE​ ​TO
REDUCE​ ​THE​ ​RISK​ ​OF​ ​PERSONAL​ ​INJURY,​ ​DISCOMFORT,​ ​PROPERTY​ ​DAMAGE,
INCLUDING​ ​DAMAGE​ ​TO​ ​YOUR​ ​[INSERT​ ​DEVICE​ ​NAME],​ ​AND​ ​OTHER
POTENTIAL​ ​HAZARDS
Handling
To​ ​avoid​ ​damaging​ ​your​ ​device,​ ​accessories​ ​or​ ​any​ ​connected​ ​devices,​ ​and​ ​to
reduce​ ​the​ ​risk​ ​of​ ​personal​ ​injury,​ ​discomfort,​ ​property​ ​damage​ ​or​ ​other​ ​potential
hazards,​ ​follow​ ​these​ ​precautions​ ​below.
Handle​ ​your​ ​device​ ​with​ ​care.​ ​You​ ​may​ ​damage​ ​the​ ​device​ ​or​ ​the​ ​battery​ ​if​ ​you
disassemble,​ ​drop,​ ​bend,​ ​burn,​ ​crush​ ​or​ ​puncture​ ​your​ ​device.​ ​Do​ ​not​ ​use​ ​a
device​ ​with​ ​a​ ​cracked​ ​screen.​ ​Using​ ​a​ ​damaged​ ​device​ ​may​ ​cause​ ​battery
overheating​ ​or​ ​injury.​ ​Don’t​ ​expose​ ​your​ ​[devices]​ ​to​ ​liquids,​ ​which​ ​can​ ​cause​ ​a
short​ ​circuit​ ​and​ ​overheating.​ ​If​ ​your​ ​device​ ​gets​ ​wet,​ ​do​ ​not​ ​attempt​ ​to​ ​dry​ ​it
using​ ​an​ ​external​ ​heat​ ​source.​ ​The​ ​device​ ​is​ ​designed​ ​to​ ​operate​ ​in​ ​a​ ​dry,​ ​indoor
environment.
Your​ ​device​ ​is​ ​designed​ ​to​ ​work​ ​best​ ​in​ ​ambient​ ​temperatures​ ​between​ ​32°​ ​to
95°​ ​F​ ​(0°​ ​and​ ​35°​ ​C),​ ​and​ ​should​ ​be​ ​stored​ ​between​ ​ambient​ ​temperatures​ ​of​ ​-4°
and​ ​113°​ ​F​ ​(-20°​ ​and​ ​45°​ ​C).​ ​Do​ ​not​ ​leave​ ​your​ ​[device]​ ​in​ ​places​ ​where​ ​the
temperature​ ​may​ ​exceed​ ​ 113°​ ​F​ ​(45°​ ​C)​,​ ​such​ ​as​ ​on​ ​a​ ​car​ ​dashboard​ ​or​ ​near​ ​a
heating​ ​vent,​ ​as​ ​this​ ​may​ ​damage​ ​the​ ​product,​ ​overheat​ ​the​ ​battery,​ ​or​ ​pose​ ​a
risk​ ​of​ ​fire.​ ​ Keep​ ​your​ ​[device]​ ​away​ ​from​ ​heat​ ​sources​ ​and​ ​out​ ​of​ ​direct​ ​sunlight.
If​ ​your​ ​device​ ​becomes​ ​too​ ​hot,​ ​disconnect​ ​it​ ​from​ ​its​ ​power​ ​source​ ​if​ ​it​ ​is​ ​plugged
in,​ ​move​ ​it​ ​to​ ​a​ ​cooler​ ​place​ ​and​ ​don’t​ ​use​ ​it​ ​until​ ​has​ ​cooled.
Contact​ ​customer​ ​service​ ​and​ ​do​ ​not​ ​use​ ​your​ ​device​ ​if​ ​it​ ​isn’t​ ​working​ ​properly​ ​or
has​ ​been​ ​damaged.
Regulatory​ ​Information
FCC​ ​Compliance​ ​Statement
This​ ​device​ ​complies​ ​with​ ​part​ ​15​ ​of​ ​the​ ​FCC​ ​rules.​ ​Operation​ ​is​ ​subject​ ​to​ ​the
following​ ​two​ ​conditions:​ ​(1)​ ​This​ ​device​ ​may​ ​not​ ​cause​ ​harmful​ ​interference,​ ​and
(2)​ ​this​ ​device​ ​must​ ​accept​ ​any​ ​interference​ ​received,​ ​including​ ​interference​ ​that
may​ ​cause​ ​undesired​ ​operation.
This​ ​equipment​ ​has​ ​been​ ​tested​ ​and​ ​found​ ​to​ ​comply​ ​with​ ​the​ ​limits​ ​for​ ​a​ ​Class​ ​B
digital​ ​device,​ ​pursuant​ ​to​ ​part​ ​15​ ​of​ ​the​ ​FCC​ ​Rules.​ ​These​ ​limits​ ​are​ ​designed​ ​to
provide​ ​reasonable​ ​protection​ ​against​ ​harmful​ ​interference​ ​in​ ​a​ ​residential
installation.​ ​This​ ​equipment​ ​generates,​ ​uses,​ ​and​ ​can​ ​radiate​ ​radio​ ​frequency
energy​ ​and,​ ​if​ ​not​ ​installed​ ​and​ ​used​ ​in​ ​accordance​ ​with​ ​the​ ​instructions,​ ​may
cause​ ​harmful​ ​interference​ ​to​ ​radio​ ​communications.​ ​However,​ ​there​ ​is​ ​no
guarantee​ ​that​ ​interference​ ​will​ ​not​ ​occur​ ​in​ ​a​ ​particular​ ​installation.​ ​If​ ​this
equipment​ ​does​ ​cause​ ​harmful​ ​interference​ ​to​ ​radio​ ​or​ ​television​ ​reception,​ ​which
can​ ​be​ ​determined​ ​by​ ​turning​ ​the​ ​equipment​ ​off​ ​and​ ​on,​ ​the​ ​user​ ​is​ ​encouraged
to​ ​try​ ​to​ ​correct​ ​the​ ​interference​ ​by​ ​one​ ​or​ ​more​ ​of​ ​the​ ​following​ ​measures:
● Reorient​ ​or​ ​relocate​ ​the​ ​receiving​ ​antenna.
● Increase​ ​the​ ​separation​ ​between​ ​the​ ​equipment​ ​and​ ​receiver.
● Connect​ ​the​ ​equipment​ ​to​ ​an​ ​outlet​ ​on​ ​a​ ​circuit​ ​different​ ​from​ ​that​ ​to
which​ ​the​ ​receiver​ ​is​ ​connected.
● Consult​ ​the​ ​dealer​ ​or​ ​an​ ​experienced​ ​radio/TV​ ​technician​ ​for​ ​help.
EMC​ ​Compliance
Important:​ ​This​ ​device,​ ​charging​ ​case,​ ​and​ ​power​ ​adapter​ ​have​ ​demonstrated
Electromagnetic​ ​Compatibility​ ​(EMC)​ ​compliance​ ​under​ ​conditions​ ​that​ ​included
the​ ​use​ ​of​ ​compliant​ ​peripheral​ ​devices​ ​and​ ​shielded​ ​cables​ ​between​ ​system
components.​ ​It​ ​is​ ​important​ ​that​ ​you​ ​use​ ​compliant​ ​peripheral​ ​devices​ ​and
shielded​ ​cables​ ​between​ ​system​ ​components​ ​to​ ​reduce​ ​the​ ​possibility​ ​of​ ​causing
interference​ ​to​ ​radios,​ ​televisions,​ ​and​ ​other​ ​electronic​ ​devices.
Changes​ ​or​ ​modifications​ ​to​ ​this​ ​product​ ​not​ ​authorized​ ​could​ ​void​ ​the
electromagnetic​ ​compatibility​ ​(EMC)​ ​and​ ​wireless​ ​compliance​ ​and​ ​negate​ ​your
authority​ ​to​ ​operate​ ​the​ ​product.
Radio​ ​Frequency​ ​Exposure
This​ ​device​ ​meets​ ​the​ ​U.S.​ ​Federal​ ​Communications​ ​Commission's​ ​(FCC)
requirements​ ​for​ ​exposure​ ​to​ ​radio​ ​waves​ ​and​ ​is​ ​designed​ ​and​ ​manufactured​ ​not
to​ ​exceed​ ​the​ ​FCC's​ ​emission​ ​limits​ ​for​ ​exposure​ ​to​ ​radiofrequency​ ​(RF)​ ​energy.
To​ ​comply​ ​with​ ​FCC​ ​RF​ ​exposure​ ​compliance​ ​requirements,​ ​this​ ​device​ ​must​ ​not
be​ ​co-located​ ​or​ ​operating​ ​in​ ​conjunction​ ​with​ ​any​ ​other​ ​antenna​ ​or​ ​transmitter.
ISED​ ​Compliance​ ​Statement​t/ISDE​ ​Déclaration​ ​de​ ​Conformité
This​ ​device​ ​complies​ ​with​ ​Innovation,​ ​Science​ ​and​ ​Economic​ ​Development
Canada​ ​licence-exempt​ ​RSS​ ​standard(s).​ ​Operation​ ​is​ ​subject​ ​to​ ​the​ ​following
two​ ​conditions:​ ​(1)​ ​this​ ​device​ ​may​ ​not​ ​cause​ ​interference,​ ​and​ ​(2)​ ​this​ ​device
must​ ​accept​ ​any​ ​interference,​ ​including​ ​interference​ ​that​ ​may​ ​cause​ ​undesired
operation​ ​of​ ​the​ ​device.
Le​ ​présent​ ​appareil​ ​est​ ​conforme​ ​aux​ ​CNR​ ​d’Industrie​ ​Canada​ ​applicables​ ​aux
appareils​ ​radio​ ​exempts​ ​de​ ​licence.​ ​L’exploitation​ ​est​ ​autorisée​ ​aux​ ​deux
conditions​ ​suivantes:​ ​(1)​ ​l’appareil​ ​ne​ ​doit​ ​pas​ ​produire​ ​de​ ​brouillage,​ ​et​ ​(2)
l’utilisateur​ ​de​ ​l’appareil​ ​doit​ ​accepter​ ​tout​ ​brouillage​ ​radioélectrique​ ​subi,​ ​même
si​ ​le​ ​brouillage​ ​est​ ​susceptible​ ​d’en​ ​compromettre​ ​le​ ​fonctionnement.
Radio​ ​Frequency​ ​Exposure
This​ ​device​ ​meets​ ​the​ ​Innovation,​ ​Science​ ​and​ ​Economic​ ​Development​ ​Canada
requirements​ ​for​ ​exposure​ ​to​ ​radio​ ​waves​ ​and​ ​is​ ​designed​ ​and​ ​manufactured​ ​not
to​ ​exceed​ ​the​ ​emission​ ​limits​ ​for​ ​exposure​ ​to​ ​radiofrequency​ ​(RF)​ ​energy.​ ​To
comply​ ​with​ ​Canada​ ​RF​ ​exposure​ ​compliance​ ​requirements,​ ​this​ ​device​ ​must​ ​not
be​ ​co-located​ ​or​ ​operating​ ​in​ ​conjunction​ ​with​ ​any​ ​other​ ​antenna​ ​or​ ​transmitter.
Exposition​ ​radiofréquence
Cet​ ​appareil​ ​répond​ ​aux​ ​exigences​ ​de​ ​Sciences​ ​et​ ​Développement​ ​économique
Canada​ ​(ISDE)​​ ​pour​ ​l'exposition​ ​aux​ ​ondes​ ​radio​ ​et​ ​est​ ​conçu​ ​et​ ​fabriqué​ ​pour
ne​ ​pas​ ​dépasser​ ​les​ ​limites​ ​d'émission​ ​pour​ ​l'exposition​ ​à​ ​l'énergie
radiofréquence​ ​(RF).​ ​Pour​ ​se​ ​conformer​ ​aux​ ​exigences​ ​de​ ​conformité​ ​à
l'exposition​ ​aux​ ​radiofréquences​ ​du​ ​Canada,​ ​cet​ ​appareil​ ​ne​ ​doit​ ​pas​ ​être
localisé​ ​ou​ ​fonctionner​ ​avec​ ​d'autres​ ​antennes​ ​ou​ ​transmetteurs.
Quick​ ​start​ ​guide
Setup
1.​ ​Prepare​ ​to​ ​connect​ ​to​ ​the​ ​G015B​ ​Bluetooth​ ​headset​ ​by​ ​turning​ ​on​ ​Bluetooth
on​ ​the​ ​companion​ ​device.
2.​ ​Open​ ​the​ ​G015C​ ​charging​ ​case​ ​next​ ​to​ ​the​ ​companion​ ​device​ ​with​ ​G015B
Bluetooth​ ​headset​ ​still​ ​inside.
3.​ ​Find​ ​the​ ​Bluetooth​ ​headset​ ​on​ ​the​ ​companion​ ​device​ ​to​ ​complete​ ​the
Bluetooth​ ​pairing​ ​connection.
4.​ ​If​ ​the​ ​Bluetooth​ ​headset​ ​is​ ​not​ ​visible​ ​on​ ​the​ ​companion​ ​Bluetooth​ ​screen,​ ​then
plug​ ​the​ ​G015C​ ​charging​ ​case​ ​into​ ​power​ ​with​ ​the​ ​charging​ ​cable.​ ​Wait​ ​10
minutes​ ​then​ ​repeat​ ​step​ ​3​ ​above​ ​to​ ​establish​ ​the​ ​Bluetooth​ ​pairing​ ​connection.
How​ ​to​ ​wear​ ​G015B​ ​Bluetooth​ ​headset
1.​ ​Pull​ ​the​ ​cord​ ​on​ ​the​ ​headsets​ ​to​ ​adjust​ ​the​ ​loops.​ ​Each​ ​loop​ ​and​ ​ear​ ​piece
should​ ​tuck​ ​comfortably​ ​into​ ​an​ ​ear.
2.​ ​Wear​ ​G015B​ ​headset​ ​with​ ​the​ ​cord​ ​hanging​ ​along​ ​the​ ​back​ ​of​ ​your​ ​neck,
making​ ​sure​ ​each​ ​ear​ ​piece​ ​labeled​ ​as​ ​L​ ​and​ ​R​ ​is​ ​in​ ​the​ ​correct​ ​Left​ ​and​ ​Right
ear.
How​ ​to​ ​charge​ ​G015B​ ​headset​ ​with​ ​G015C​ ​charging​ ​case
1.​ ​Place​ ​the​ ​G015B​ ​headset​ ​ear​ ​pieces​ ​in​ ​the​ ​G015C​ ​case​ ​to​ ​charge​ ​on​ ​the​ ​go.
2.​ ​To​ ​charge​ ​the​ ​G015C​ ​case,​ ​plug​ ​in​ ​the​ ​charging​ ​USB​ ​cable​ ​and​ ​to​ ​a
compatible​ ​USB​ ​charger.
3.​ ​When​ ​G015B​ ​Bluetooth​ ​headset​ ​ear​ ​pieces​ ​are​ ​in​ ​the​ ​G015C​ ​charging​ ​case
with​ ​the​ ​lid​ ​open,​ ​the​ ​lights​ ​show​ ​the​ ​battery​ ​life​ ​of​ ​your​ ​headset.​ ​All​ ​three​ ​lights​ ​lit
indicate​ ​fully​ ​charged.
Press​ ​the​ ​button​ ​on​ ​the​ ​inside​ ​right​ ​of​ ​the​ ​G015C​ ​case​ ​to​ ​check​ ​battery​ ​life​ ​of​ ​the
charging​ ​case​ ​as​ ​indicated​ ​by​ ​the​ ​lights.
4.​ ​To​ ​close​ ​the​ ​charging​ ​case​ ​with​ ​headset​ ​inside,​ ​wrap​ ​the​ ​cord​ ​around​ ​and
inside​ ​casing​ ​till​ ​the​ ​end​ ​of​ ​the​ ​cord​ ​is​ ​tucked​ ​between​ ​the​ ​L​ ​and​ ​R​ ​ear​ ​pieces.
G015B​ ​headset​ ​touch​ ​controls​ ​(on​ ​the​ ​R​ ​right​ ​outside​ ​housing​ ​ear​ ​piece
only)
1.​ ​Tap:​ ​Play​ ​/​ ​Pause​ ​/​ ​Answer​ ​/​ ​or​ ​End​ ​a​ ​call
2.​ ​Swipe​ ​forward​ ​/​ ​back:​ ​Turn​ ​volume​ ​up​ ​/​ ​down

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Producer                        : Skia/PDF m63
Page Count                      : 4

EXIF Metadata provided by EXIF.tools