Welcat CSH07334 RFID IC Card/IC Tag Reader/Writer User Manual 2nd M01CSH06349

Download:
Mirror Download [FCC.gov]
Document ID	906543
Application ID	w7vSdhmHBiIdv3mfYVlalg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	226.95kB (2836876 bits)
Date Submitted	2008-02-26 00:00:00
Date Available	2008-02-27 00:00:00
Creation Date	2007-10-01 14:46:09
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2008-01-08 13:15:00
Document Title	Microsoft Word - 2nd_M01CSH06349.doc
Document Creator	Adobe Illustrator CS3
Document Author:	jun

Users Manual
CSH-07334
IC Card/IC Tag Reader/Writer
CSH-07334
US Regulations
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Note:
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more
of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
Warning:
You are cautioned that changes or modifications not expressly approved
by the party responsible for compliance could void your authority to
operate the equipment.
Trademarks
Microsoft、MS are the U.S. Microsoft Corporation's registered trade-marks or the trademarks in the U.S.
or other countries.
Windows XP、Windows 2000 are the U.S. Microsoft Corporation's registered trade-marks or the
trademarks in the U.S. or other countries.
my-d is the Infineon Technologies Inc.'s registered trade-marks or the trademarks.
I･CODE is the NXP Semiconductors Inc.'s registered trade-marks or the trademarks.
Tag-it is the Texas Instruments Inc.'s registered trade-marks or the trademarks.
FerVIDfamily is the Fujitsu Inc.'s registered trade-marks or the trademarks.
The products and corporate names which are described in addition are the registered marks or brand of
each enterprise.
SAFETY PRECAUTIONS
・ Be sure to read these precautions before using this product in order to insure safe operation of the
equipment.
・ Keep this User's Manual on hand for future reference whenever you may need it.
Strict observance of these warning and caution indications are MUST for preventing accidents which
could result in bodily injury and substantial property damage. Make sure you fully understand all
definitions of these terms and related symbols given below, before you proceed to the text itself.
Danger
This symbol indicates an item that can result in death or serious personal injury if ignored and
emergency of warning when dangerously generated is high.
Warning
This symbol indicates an item that can result in death or serious personal injury if ignored.
Caution
This symbol indicates an item that can result in serious personal injury or material damage if ignored.
Meaning of Symbols.
A diagonal line through a circle indicates something you should not do
A black circle indicates something you must do.
A triangle inside indicates something you should be careful about.
Be sure to observe the following matters to prevent injury to the users and others and possible damage
to the property.
ii
Observe strictly
Warning
Observe the display of the danger that the manufacturer of the personal com-puter and
peripherals used is directing and warning and attention strictly when you use the product.
Do not attempt disassemble or
modify the products, which may
result in injury, electric shock,
excessive heat, fire.
Do not use this product in a place in
danger of catching fire and
exploding.
Do not use this product near the
electric device which processes
highly precise control and a weak
signal.
Do not put a foreign substance into
the inside of a main body.
Using it in a place generating
flammable gas and dusts can cause
explosion and fire.
When a foreign substance or a liquid
go into the inside of the main body,
stop use, and inform the store of
purchase.
It may influence electric devices
(such as medical treatment electric
device, fire alarm, automatic door,
other automatic control apparatus,
etc.) to gen-erate malfunction etc.
When it is then used, it will become
accidents, such as an electric shock
and a fire, or the cause of failure.
Do not bring close to chemicals.
This product is not developed, not
intended, not permitted to use this
product for the equipment, (atomic
energy control, aircraft flight control,
air traffic control, mass transport
control, life support system, and
weapon control systems, hereinafter
"High Safety Required Use"), whose
failure could threaten directly human
life or affect human body.。
Do not use and keep it near
chemicals or in the place which
chemicals touch.
It becomes accidents, such as an
electric shock and a fire, or the
cause of failure.
iii
Warning
Do not place or use the products in
the hot, high humid or dusty places
such as a fire side, a stove side,
under the burning sun, etc.
Doing so could cause a fire, burn,
bodily injury, or serious damage to
property.
Do not place or use products in high
humid or dusty areas.
Doing so could cause a fire, burn,
bodily injury, or serious damage to
property.
Do not put in in water, and sprinkle
water by strong power.
Do not give the high impact.
Do not drop, do not throw out, and do
not beat the main body. It becomes
malfunction of the main body, and
the cause of failure.
If water will gets into the products,
resulting in failure, fire or electrical
shock.
Do not put it in an unstable place.
Do not put it in the place which an
infant's hand reaches.
Apparatus drops or falls down and it
causes an injury and a failure of the
apparatus.
Only use
peripherals.
the
specified
It becomes cause, such as an injury.
our
This product is communication equipment using 13.56MHz radio wave.
Interference may be generated depending on how and where it is used. To
decrease the effect by the interference, we recommend you make a mutual
check in advance before installation.
The product may affect the operation of radio astronomical unit, medical or other
equipment. Take special care when using the product in an environment where such
equipment is being used. When installing or repairing this product, it is also
necessary to use caution against human exposure to radio waves for a long period.
Bundled items
■CSH-07334 Unit.................................. １
■USB cable........................................... １
■Brief manual........................................2
■RDID sticker........................................ １
■CD-ROM ............................................. １
iv
Contents
Bundled items ..................................................
Contents .......................................................
Introduction...................................................
Notational Information .........................................
iv
vi
vi
HARDWARE.......................................................1-1
1-1 P ART NAMES AND FUNCTIONS
...............................................................1-2
1-2 S PECIFICATION OF CSH-07334......................................................1-3
1-2-1
1-2-2
1-2-3
1-2-4
1-2-5
Environmental condition .................................. 1-3
Hardware specification .................................. 1-3
Appearance specification ................................. 1-4
Operating environment .................................... 1-4
Communication interface specification .................... 1-4
1-3 H OW TO HOLD THE IC CARD /IC TAG ............................................................... 1-5
SOFTWARE.......................................................
. 2-1
2-1 H OW TO INSTALL THE DRIVER SOFTWARE
............................................................... 2-2
2-1-1 Installing the driver software ........................... 2-2
2-1-2 Connecting to Windows XP.................................2-3
2-2 C HECKING AFTER CONNECTION .............................................................. 2-5
2-3 U NINSTALLING THE DRIVER SOFTWARE ............................................................. 2-6
FAQ (FREQUENTLY ASKED QUESTIONS) ............................................... 3-1
3-1 FAQ (FREQUENTLY ASKED QUESTIONS) .............................................................. 3-2
Q：I connected CSH-07334 before installing the driver ......................................3-2
Q：CSH-07334 does not operate properly after installing the driver............3-2
Q：A “! ” mark is put on the beginning of “ CSH-07334 ” on the [Device manager] screen.
......................................................3-2
Introduction
Thank you for purchasing our IC tag/IC card reader writer “CSH-07334”.
CSH-07334 is a reader writer compatible with IC/cards/IC tags of the following makers.
・ Infineon Technologies “my-d”
・ Texas Instruments “Tag-it HF-I”
・ NXP Semiconductors “I・CODE1” “I・
CODE SLI”
・ Fujitsu “FerVIDfamily”
It is a guidance type read/write communication equipment (model designation acquired) that can
read multiple tags collectively (anti-collision function).
This user manual describes how to use the hardware of the CSH-07334 unit and the driver
software.
We are happy if CSH-07334 is useful for improving efficiency of your business.
This product conforms to the RoHS Directive.
RoHS：Abbreviation of Restriction of the use of the certain Hazardous Substances in electrical and
electronic equipment
RoHS is a regulation of harmful substance enforced by the European Union for
electronic and electric equipment, which prohibits the use of six substances consisting
of lead, hexavalent chromium, mercury, cadmium and two different types of
bromine-based fire retardants, namely PBB (polybrominated biphenyl) and PBDE
(polybrominated diphenyl ether) .
Notational Information
Indicates a note you can refer to.
Indicates a caution.
CSH-07334
IC Card / IC Tag Reader/Writer CSH-07334.
vi
Chapter 1
Hardware
Chapter 1 Hardware
1-1
Part names and functions
① PW LED
This lights up in red when the power is turned on.
② R/W LED
This lights up in green when the equipment reads and writes a card (tag).
③ RF LED
This lights up in yellow when the radio wave is outputted.
④ USB connector
Connect the attached USB cable with PC.
⑤ Buzzer sound hole
⑥ Product nameplate
Model
Serial Number
IC Card / IC Tag Reader Writer
C S H-07334
SER
No.
********
MADE IN JAPAN
1-2
10
CMII ID:
FCC ID:Q98CSH07334
1-2 Specification of CSH-07334
1-2
Specification of CSH-07334
1-2-1
Environmental condition
Item
Specification
Working temperature 0 to 40ºC (There should be no rapid
temperature change and condensing.)
Working humidity
20 to 80%
Storage temperature -10 to 50ºC (There should be no rapid
temperature change and condensing.)
Storage humidity
1-2-2
10 to 90%
Hardware specification
Indicator LED
PW LED
Red
Lights up when the power is turned on.
R/W LED
Yellow
Lights up when the radio wave is outputted.
RF LED
Green
Lights up for reading and writing (user application
control enabled)
Buzzer
Sounds for reading and writing or user application
Size
81 (W) ×128 (D) ×17 (H) mm
Weight
81g
Power
USB bus power Maximum consumption current 250mA
External interface
Standard
Compliant with USB Specification Rev 1.1 (High Power device)
Device class
COM class
Cable length
1.0m
Radio
frequency
13.56MHz
Radio output
Maximum 100mW
Reading
distance
0 to 5cm*1
Compatible
tag
Tag-it HF-I, I･CODE SLI, my-d, FerVID family*2, I･CODE1
RFID part
＊1
This may vary depending on the performance of the tag and the environment.
＊2
Compatible FerVID family is MB89R116/MB89R118.
Be sure to use a self-power HUB to connect it using a USB HUB.
1-3
Chapter 1 Hardware
1-2-3
Appearance specification
1-2-4
Operating environment
●Compatible OS (Japanese version)
・ Windows XP
・ Windows 2000
●Environment
・ CD-ROM drive
Required to install the driver
・ USB connector
One required to connect this product (A type)
1-2-5
Communication interface specification
・ Connector: USB miniB type connector
・ Terminal function: Compliant with USB Specification Rev1.1
・ Device class: COM class compliant with (“Communication Device Class Abstract Control Model”)
1-4
1-3 How to hold the IC card/IC tag
1-3
How to hold the IC card/IC tag
This equipment accesses the IC card/IC tag in the range shown by the shaded area in the figure below. Be
careful not to let it go beyond the range during access.
Communication range: About 5cm from the center of the unit when the tag and the unit are held horizontally
(for the credit card size)
■To use a small tag
Use it within the following range.
If the tag used is extremely small, reading it may fail.
1-5
Chapter 1 Hardware
■To use CSH-07334 laid side-by-side
To use CSH-07334 laid side-by-side, isolate CSH-07334 by about 10cm. If the distance is too
close, the communication performance may be affected.
1-6
Chapter 2
Software
Chapter 2 Software
2-1
How to install the driver software
2-1-1 Installing the driver software
Install the driver software of CSH-07334 according to the following procedure.
Install the driver software before connecting CSH-07334.
① Turn on the power of your PC and start Windows.
Log in with a system administrator authorization.
② Insert the CD-ROM bundled with the product into the CD-ROM drive.
③ Click [My computer]→[CD-ROM drive]→[CSH-07334]→[drivers]→[PreInstaller.exe].
④ Select a folder to install the driver and press the [Install] button.
The Welcat folder is created in the Program Files folder before installation by
default.
⑤ The following screen appears during installation.
Microsoft performs a qualification procedure for PC units and peripheral devices in an
organization called WHQL. CSH-07334 has not been qualified as of February, 2006.
Click [Continue] here to continue installation of the driver of CSH-07334.
2-2
2-1 How to install the driver software
⑥ When the following screen appears, click [OK] and take out the CD-ROM.
⑦ Use the attached cable to connect CSH-07334 to your PC.
If you use Windows2000, the installation operation is complete.
If you use WindowsXP, proceed to “2-1-2 Connecting to Windows XP” (P.2-3).
2-1-2 Connecting to Windows XP
If you use Windodws XP, carry out the following setting after installing the driver software (P.2-2).
① When you connect CSH-07334 to your PC, the following screen appears.
Select [No, I don’t connect this time] and proceed to the next.
② Select [Install software automatically] and proceed to the next.
2-3
Chapter 2 Software
③ The following screen appears during installation.
Microsoft performs a qualification procedure for PC units and peripheral devices in an
organization called WHQL. CSH-07334 has not been qualified as of February, 2006.
Click [Continue] here to continue installation of the driver of CSH-07334.
④ When the following screen appears, the driver of CSH-07334 has been installed.
Click [Complete].
After this, installation of the driver starts again. Repeat the same procedure as that described in
① through ④.
2-4
2-2 Checking after connection
2-2
Checking after connection
After installing the driver software, check if CSH-07334 is correctly connected.
① Right-click [My Computer] and select [Property] or [Control].
② Double-click [Port (COM and LPT)] on the device manager screen (“Device manager” tab) and
check that CSH-07334 is displayed.
The COM number varies depending on the environment of your PC.
③ When you have finished checking, close the screen.
Every time the USB port to which this product is connected changes, you need to
install the driver software. In that case, install it in the same procedure.
2-5
Chapter 2 Software
2-3
Uninstalling the driver software
Uninstall the driver according to the following procedure.
① Select [Adding and deleting programs] from [Control panel].
② Select [e-front CSH-07334 Controller] from the list and press [Change and delete] button to
delete it.
・ Keep CSH-07334 connected to your PC to uninstall the driver.
・ Remove CSH-07334 from your PC after you have uninstalled the driver.
2-6
Chapter 3
3 FAQ (Frequently asked questions)
Chapter 3 FAQ
3-1
FAQ (Frequently asked questions)
This section describes frequently asked questions, troubles, items requiring checking to resolve those
troubles and reference pages on this manual. Make an inquiry to our Website for those troubles you can not
resolve here.
Q：I connected CSH-07334 before installing the driver.
A：Install the driver manually.
The driver software is included in the [Drivers] folder of the bundled CD-ROM. See the folder to
install the driver.
Q：CSH-07334 does not operate properly after installing the driver.
A：The USB cable may not be connected properly.
Check that the USB connecter is fully inserted into the USB port of your PC.
A：The driver may not be properly installed.
Install the driver in the following procedure again.
① See “2-3 Uninstalling the driver software” (P.2-6) to uninstall the driver.
② Turn off the power of your PC, remove CSH-07334 and turn on the power of your PC.
③ See “2-1-1 Installing the driver software” (P.2-2) to install the driver again.
A： CSH-07334 may be misidentified.
Install the driver in the following procedure again.
① When [Other devices] is displayed by [Device manager]
Right-click [Unknown device] or [USB Device] displayed below and click [Delete].
② When [Other devices] is not displayed
Select [Device (by connection)] from [Display] and check if there is [Unknown device] or
[USB Device] under the USB host controller. If you find one, select the device and click
[Delete] button.
If you can’t find any by searching, restart your PC and install the driver from the beginning
again.
③ Turn off the power of your PC, remove CSH-07334 and turn on the power of your PC.
④ See “2-1-1 Installing the driver software” (P.2-2) to install the driver again.
Q：A “!” mark is put on the beginning of “CSH-07334” on the [Device
manager] screen.
A：The driver may not be properly installed.
Install the driver in the following procedure again.
① See “2-3 Uninstalling the driver software” (P.2-6) to uninstall the driver.
② Turn off the power of your PC, remove CSH-07334 and turn on the power of your PC.
③ See “2-1-1 Installing the driver software” (P. 2-2) to install the driver again.
3-2
IC Card / IC Tag Reader / Writer
CSH-07334
Users Manual
September, 2007
Manual Rev.1.0
Copyright ©2007
Welcat Inc.
http://www.welcat.co.jp/
info@welcat.co.jp
M01CSH-07334

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Creator Tool                    : Adobe Illustrator CS3
Modify Date                     : 2008:01:08 13:15+09:00
Create Date                     : 2007:10:01 14:46:09+09:00
Metadata Date                   : 2008:01:08 13:15+09:00
Thumbnail Width                 : 164
Thumbnail Height                : 256
Thumbnail Format                : JPEG
Thumbnail Image                 : (Binary data 9034 bytes, use -b option to extract)
Document ID                     : uuid:989d187e-5dc7-449b-a16a-c8beb015d17d
Instance ID                     : uuid:cf614efd-5ab9-4727-89a5-26662b462bb7
Format                          : application/pdf
Title                           : Microsoft Word - 2nd_M01CSH06349.doc
Creator                         : jun
N Pages                         : 1
Has Visible Transparency        : False
Has Visible Overprint           : False
Max Page Size W                 : 595.219971
Max Page Size H                 : 842.000000
Max Page Size Unit              : Points
Font Name                       : ArialNarrow, ArialMT, Impact, Arial-Black, DFSMGothic-Lt-WING, HiraginoKaku-W7-90msp, ArialBold
Font Family                     : Arial Narrow, Arial, Impact, Arial Black, DFSMGothic Lt-WING-90ms-RKSJ-H, HiraginoKaku W7-90msp-90ms-RKSJ-H, ArialBold 90ms-RKSJ-H
Font Face                       : Regular, Regular, Regular, Regular, Lt-WING-90ms-RKSJ-H, W7-90msp-90ms-RKSJ-H, 90ms-RKSJ-H
Font Type                       : Open Type, Open Type, Open Type, Open Type, Unknown, Unknown, Unknown
Font Version                    : Version 2.30, Version 3.00, Version 2.35, Version 2.35, Version 2.30, Version 2.30, Version 2.30
Font Composite                  : False, False, False, False, False, False, False
Font File Name                  : ARIALN.TTF, ARIAL.TTF, IMPACT.TTF, ARIBLK.TTF, MSGOTHIC.TTC, MSGOTHIC.TTC, MSGOTHIC.TTC
Plate Names                     : Cyan, Magenta, Yellow, Black
Swatch Group Name               : 初期設定のスウォッチグループ
Swatch Group Type               : 0
Page Count                      : 23
Author                          : jun

EXIF Metadata provided by EXIF.tools