Westell C90327WXX-06 4 Port wireless gateway router User Manual Part II

Westell Inc 4 Port wireless gateway router Users Manual Part II

Users Manual Part II PDF Download & Text

1. Users Manual Part I
2. Users Manual Part II

Users Manual Part II

Download:
Mirror Download [FCC.gov]
Document ID	554259
Application ID	c7F0eVp5uZG925W3334GPA==
Document Description	Users Manual Part II
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	291.31kB (3641367 bits)
Date Submitted	2005-06-21 00:00:00
Date Available	2005-06-20 00:00:00
Creation Date	2005-06-21 14:24:44
Document Lastmod	2005-06-21 14:24:56
Document Title	Users Manual Part II
Document Creator	Canon

‘ 0304900451 Rev. A
‘ BdlSullthVersaLinkCateway
WEST 6/1/05 — Drllt 2
User Guide VersaLink Gateway (Model 327W)
If you click on Home Network at the main menu, the following page will be displayed. This page enables yen to set
up the network settings on your modem. To conﬁgure the settings, click the desired submenu button at the right of
the page.
NOTE: IfVexsaLink is conﬁgured fur ETHERNET PORT 1 mode, the QoS and VLAN buttons will not be
displayed in the Home Network page You must conﬁgure VersaLink for DSLATM PORT mode to use these
functions.
BellSouth’
Home ‘andtmnd ‘ ' ' \ WNW“; ' ~ FasiAccess"
,.i'f"'f".,°7 ,,.°5“i"" ,/ , v 4, """W°’d’_ WW???) lnternetService
7‘ ethemei "
IP Address / Name MAC Address Connecllnn Slams Connsdinn Type
192.159.1 19 / salts-932 Du: 5n:da:b2:d9:fl Active Ethernet
wireless
smlnn MAC Address state Anlva Rats “mm”,
- / ' ﬂﬂ::0:4§:a§.3h:1h Authnnzed 54 Misti/set:
OED-300452 Revl A 84 May 2005
030400452 Rev. A
BellSnurhVersaLinkGlhzwly
w-TELL 6/1/05 — mm 2
User Guide VermLink Gateway (Model 327W)
If you click the Private LAN button in the Home Network page, the following page will be displayed, (Private
LAN is the default conﬁguration for the VersaLinkT“ Gateway)
NOTE: Private LAN allows you to set up a network behind VersaLink.
If you change any settings in this page, click on save changes to allow the settings to take effect, Click the Back
button to return to the Home Network page.
BeIISouth"
n ' s dbod . ’r u _ , FastAccess
efﬁii'iv ﬁlms,“ ”gm" .. my?” ”may, “Wmf'f‘; lnternetﬁervice
Frivut' LAN anv Samar Enable E7
Prlvatu LAN Enable p
Mndem 19 Address |92.t6dt254
suhnel Mask 255 255255.»
1 Private LAN DHCP Settings
m—tcv start Adduss Wat ,
pact: and Address |92.| Gm 151
i DHcPLeaseTtme |— I r = [r z |r
pays Hours M'mltes 59mm:
If you made changes to the Private LAN Configuration page and clicked on save changes, the following pop-up
screen will be displayed Click on OK. This will save your Private LAN Conﬁguration settings, If you click Cancel,
your new settings will not take effect.
M“ msott Internet E lover
030-300452 Rev. A 85 May 2005
ash-sous: 11m. A
BellSouthVernLiukGateway
wes’rau. 6/1/05 — Draft 2
User Guide VersuLin/c Gateway (Model 327W)
Private LAN Conﬁguration
Private LAN DHCP Server Enable Default = CHECKED
If this box is CHECKED, it enables DHCP addresses to be sewed from
the Private LAN pool.
Private LAN Enable Default = CHECKED
If this box is CHECKED, it enables the addresses from the Private LAN to
use the NAT interface.
Modem H’ Address Displays VersaLink’s 1? address
Subuet Mask Displays the Suhnct Mask, which determines what portion of an IP
address is controlled by the network and which portion is controlled by the
host.
r_1’_r_ivate LAN DHCP Settings
DHCP Start Address Displays the ﬁrst IP address that the DHCP sewer will provide.
DHCP End Address Displays the last IP address that the DHCP server will provide.
DHCP Lease Time Displays the amount of time the provided addresses will be valid, aﬂer
which the DHCP client will usually re-suhmit a request.
NOTE: DHCP Lease Time is displayed in the following format: (Days:Hours:Minutes:Seconds). This value must be
greater than 10 seconds. The default = 01:00:00:00. Seconds must be between 0 and 59, minutes must be between 0
and 59, and hours must be between 0 and 23.
If the settings you have entered in the Private LAN Conﬁguration page are incorrect, the following warnings
messages may he displayed via pop-up screens. If this occurs, check the settings in the Private LAN Conﬁguration
screen.
Warning Message Check Private LAN DHCP Settings
Start Address is not part of the Subnet Check the value in the DHCP Start Address ﬁeld
End Address is not part of the Subnet Check the value in the DHCP End Address ﬁeld
End Address is below the Start Address Check the value in the DHCP End Address ﬁeld
Lease time must be greater than 10 seconds Check the values in the DHCP Lease Time ﬁelds
Seconds must be between 0 and 59 Check the Seconds value in the DHCP Lease Time ﬁeld
Minutes must be between 0 and 59 Check the Minutes value in the DHCP Lease Time ﬁeld
Hours must be between 0 and 23 Check the Hours value in the DHCP Lease Time ﬁeld
030-300452 Rev. A 86 May 2005
010-300451 Rev. A
M BelISnuthVersaLlnkGatewny
W‘TELL 6/1/05 - Draft 2
User Guide VersaLink Gateway (Model 327W)
If you click the IP Passthrough button in the Home Network page, the following [P PassthroughIDMZ page will
be displayed. The IP Passthrough/DMZ page enables you to select the device on your LAN that will share your
single static IP address. Before you begin this section, conﬁgure your PC settings to obtain an IP address from
VersaLink automatically (Refer to your Windows Help screen for instructions.)
rSTOP: Static NAT must be disabled (if it has been previously enabled) before you can enable [P Passthrough.
Refer to section 11.3.4] (Disabling Static NAT) for instructions on disabling Static NATr Aﬂer you have disabled
Static NAT, return to the IP Passthrough/DMZ Conﬁguration page.
NOTE: I? Passthmugh/DMZ allows the user to share the WAN assigned IP address with one device on the LAN.
When lP Passthrough/DMZ is conﬁgured on the modem, the device with the $51 becomes visible on the Internet.
Network Address Translation (NAT) and Firewall rules do not apply to the device conﬁgured for 851. If you are
using the Bridge Ethernet protocol, IP PassthrougthMZ conﬁguration will not be available.
11.2.1.1 Enabling IP Passthrough/DMZ
To enable IP Passthrough/DMZ, go to the Passthrough/DMZ Conﬁguration page and select a device from the
options displayed in the window. Next, click on enable.
NOTE: If you select “User Conﬁgured PC," a local PC must be manually conﬁgured to have the Passthrough IP
address,
BeIlSouth"
FastAccess”
‘ ﬁrewall and h _
_4 Intemel Sen/ice
Home Broadband Home
Summary 1:51 line Newark “We“
that
Please select which device will snare your pubic n: address,
If was: conﬁgured pc' is meted, a local pcmusi be mamaify conﬁgured to use wpubh'c IP
seas-s;
wan w Addrﬁss: in 15.9n.5
Useroann uredPC
IF Fussthrough ls curmmy disabled.
030-300452 Rev. A 87 May 2005
030400452 Rev. A
BellsnuihversaLinkGalewzy
WELL 6/1/05 — Drift 2
User Guide VersaLink Gateway (Model 327W)
If you clicked on enable, the following pop-up screen will be displayed. Click OK to continue, or click Cancel to
abort.
If you click OK, the modem must be resei in order for the new conﬁguration to take effect. Click 0K to reset now,
or click Cancel to abort.
While the modem is resetting, the following screen will be displayed.
> warning
mum; Mnﬂlm Pl-ns- well...
we modem is nu - g n. aw for
m. mum-u using" as m. mm.
Your 9-9- w! a. mama mm
030-300452 Rev. A 88 May 2005
‘ use-300451 Rev. A
BettSnuihVemLtnkGateway
WESTELL Gums-Dun 2
User Guide VersaLink Gateway (Model 327W)
After the modern has been reset, the Home Summary page will be displayed. Conﬁrm that the DSL and Internet
Logln ﬁelds display Up.
NOTE: If your Modem’s connection type is set to “Always On" or “On-Demand,” aﬁer a brief delay, an Internet
connection (PPP session) will be established automatically and the Home Summary page will be displayed. If the
connection type is set to “Manual,” you must click the Connect button in the Easy Login page to establish an Internet
Connection. Once the Internet connection has been established, you may proceed with your modem‘s conﬁguration.
Always On is the factory default connection type for this modem Refer to section 10.1 for details on oonnection type.
BeIlSouth‘
FastAccess"
InlemelServlce
m; me; he“, ﬁgg‘ Wm...
Numeb‘ummorv
net. Do me u. vars-Ink l
lmnmlllngh u, Mndllmmbnr cwmwzws .
umm umamlmlsmlhut mom..- human”? l
m w Addnu mums mm v-rslun mm l
humour-um mum‘s/m) m. ‘
“l
upstmmmuoﬁu/snc) m
wanyB-u Vhismmmhasnnlvﬁlcnnnnemdlolﬁ-lnl n
‘ a...“ welww Eumnmrv
' w nummuT
in Adams I mm Mu: Addnss Inlrvld land 19 cwlqlanfyyo l
mm sum-m mum bum mien,“ wussmmugn l
sin-um l
‘ 1» Adam“ 1 Home rm Amtnss ammo" Ellui mmnnlwn'l’vvn ‘
mm.“ ‘
lullnn me my.” Eula mm m-
When ll> Passthmugh/DMZ is enabled, the following page will display the message “IP Pusthrough is currently
enabled for” and the device that you selected to share the public IP address.
BelISouth‘
FuslAccess’
new“
name, “W"k‘ , mmrnzt Service
n a.,-;.......9.VM Wm“...
pm». m. mum. ..u m. yww i» am.
"WWW'C'MWMahﬂl’cmtummﬂyzmwmm-mww
mm in um“: um ms
mummy-ea a:
n Passtlluuwh is mntly mm m
"um-z
(BO-300452 Rev. A 89 May 2005
' nan-300452 Rev. A
BellSﬂuLhVelsnLinkGalcwly
WEI'EJ. 6/1/05 - Draft 2
User Guide VersaLink Gateway (Model 327140
1 1.2.1.2 Disabling IP Passthrough/DMZ
To disable IP Passthmugh/DMZ (if it has been previously enabled), go to the PassthroughIDMZ Conﬁguration
page click on disable.
Bel I South"
ﬁrawnand , FuslAccess"
5mm:
“meg? mm“;
4 , ‘
u in;m.mug'ninm'i'cuhigurinn
Phase swlecl wh'mh dwinw wiH sham wi mm: m mam,
,, 1 M Q
"WWW-“mm.mmwwwwwmmmm \
mm".
mm m mums: “use“
Ul-Canignd Pc
1» passmmunh .s cummily unkind luv
‘
“mm ;
Next, click OK in the pop—up screen to disable IP Passthrough
met Explorer m
If you click OK, the modem must be reset in order for the new conﬁgn'ation to take effect. Click OK to reset now,
or click Cancel to abort.
030-300452 Rev. A 90 May 2005
DID-300452 Rev. A
BeIISouthVerstlnantewny
WETELL ﬁll/“5 — Drill 2
User Guide VersaLink Gateway (Model 327W)
While the modem is resetting, the following screen will be displayed.
> warning
N'yﬂung Mahmqul-n Wm...
in. mud a "yum; m an!" n-
m. mm 4 amps w m- emu.
vnurelg- w! a. mead-u smiv.
After the modem has been reset, the Home Summary page will be displayed. Conﬁrm that the DSL and Internet
Lngin ﬁelds display Up in the Home Summary page.
NOTE: If your Modam’s connection type is set to “Always On” or “On-Demand,” aﬁer a brief delay, an Internet
connection (PPP session) will be established automatically and the Home Summary page will be displayed. If the
connection type is set to “Manual," you must click the Connect button in the Easy Login page to establish an Internet
connection. Once the Internet connection has been established, you may proceed with your modem‘s conﬁguration.
On-Demand is the factory default connection type for this modem. Refer to section lot] for details on connection type.
BelISouth'
M. mm". emu.” . . FasMccess
summary on we MM”: "WWW“ Internet Service
., M. m/ x. . . A,
Home summary
DEL Down Valsllitk
mum-n Logln om Mudwi Nam-r mn-anwan-os
Ilslr in urlmameohellwum net mm Numhnr nssumqnuq
wan w Adﬂrws Dwm Srmwnru chshn imam
Downstream m. “Eu/Sea} m, DSL connection
Husk-um m- (ms/s-c) m, DSL Gem-slim
warranty mm "is modern has not m Danni-slid m bhl mum-t
Home Nuzwm summm
mum:
ID “1de / Mama mu: Address Com-nah" emu; cum-aim. m7.
19245944; / - Du m‘ﬂaztﬂtﬂsch min Eihamut
wlmlm
MAC Andrus: mm mm mm
030-300452 Rev, A 91 May 2005
030600452 Rev. A
. BellsnuthersaLinkGaleway
TE 6/1/05 — Draft 2
User Guide VersaLink Gateway (Madel 327W)
When 1? Passthmugh/DMZ is disabled, the following page will display the message “IP Passthrough is currently
disabl ."
BeIISouth‘”
”um » » ~ - w - (Mum xFastAcceSS'
~ . x D' 71k -
‘ Summary ; b l, J \ “MW“ “81?wa lnternetSerwce
Please salsct wmch dun/in. will share vnurpublic In address.
If mar conﬂwroch' I: selected, a IocalPCmuRbe manually conﬁgamd we we tbspablic 1p
mm
WAN w Addr'ss: missus
Use! Cnrmgumd PC
“HMS?
lﬂ Dassthrmgh is cmnlly ﬁsahlud.
030-300452 Rev. A 92 May 2005
030400451 km. A
Bellsoutthl'ssLlnantewny
WﬁTELL 6/1/05 - Draft 2
User Guide VersaLin/c Gateway (Model 327 W)
If you click the NAT/Gaming button in the Home Network page, the following NAT Conﬁguration page will be
displayed. The NAT Conﬁguration page enables you to set up NAT services for your modem.
Westell has developed an extensive list of NAT services, and you may select any service from this list. By selecting
your speciﬁc NAT service and setting up a NAT proﬁle, you will ensure that the appropriate ports on the modem are
open and that the required application trafﬁc can pass through your LAN. For a list of supported services, go to
section 15 (NAT Services), You may add an unlimited number of NAT services.
NOTE: The NAT/Gaming menu option will not be available if you are in Bridge Ethernet mode.
BellSouths
My; Mum” um Wm ﬂaw/w WM FustAccess
.,‘"’"”"”’¥ “555"? ».”e‘”‘"* “WW?“ lntemEtSerwce
w Cnvlhgurationr
55m“ ”a“ SelenAswue
'-' Denotes omen. service
Sewlce Name service Mode Hosr own:-
“558: Am cum 0mm
NAT Conﬁguration
Service Name A drop-clown menu of NAT (Network Addless Translation) services that you
can select from when you are ready to conﬁgure your modem for NAT
service.
NAT Table Monitoring Factory Default = Disabled
If Enabled, this feature will monitor trafﬁc on the ports.
030400452 Rev. A 93 May 2005
BSD-300452 Rev. A
‘ BelISnuthVersnLinanlmvny
WETELL 6/1/05 —- Drift 2
User Guide
11.3.1 Adding NAT Services
VersaLin/c Gateway (Model 32 7W)
To add a NAT service, from the NAT Conﬁguration page select a service from the Service Name drop-down menu.
Home " ‘mm'e' ”Wm" 1 ‘ f ' 'ﬁrem"'iian{i
Summary mum Network ‘ WM“ Fauwnrds
Magnetic;
Bel lSouth‘
FﬂslAccess‘
lnlemet Service
mmmmnmnmm a!
mum.-
AgclEmp'nl llzmunqulmm
mm: Mn.
Mum's w
. Bubuﬂ Ga:- 1
Ball-mm
5mm sun. nII
slux unwan-
nn Yahlx Mnnimring
mil)-
For example, the following page displays Alien vs. Predator as the NAT service selected. After you have selecued a
service, click the enable button adjacent to Service Name.
ﬁrwallnnd
ﬁauwnrds
“Ni“ "U" Nilmw.H-ddnv ~
‘Wﬂommr cum swvim
"who. Nam- Hm Blvlcl
wssc Au Dynam:
Mu (an-n sz
un m1. Mnnimviﬂg mu.
030-300452 Rev. A 94
Diagnostics
BeIISouth"
FastAccess’
meme! Senice
May 2005
“30600452 Rev. A
BellsouterersaLinkGalewny
WESTELL 6/1/05 — Drlﬂ 1
User Guide VersaLink Gateway (Made! 327W)
If you clicked enable, the following pop-up screen will be displayed. If you click OK in the pop-up screen, you will
allow incoming connections to be forwarded to a designated local PC. If you click Cancel, you will allow only
outgoing connections from any local PC. Click OK or click Cancel.
NOTE: If you click Cancel in the following pop-up screen, the NAT service you selected in the Service
Conﬁguration page is still configured; however, it will not be assigned to any device on the local LAN. You must
click OK to host the NAT service.
M“ In R lnternel Explorer
If you clicked 0K in the preceding pop-up screen, the Host Device page will be displayed. The Host Device page
will enable you to select which device will host the NAT service you selected on your local area network, Aﬁer you
have selected a device from the Host Device drop-down menu, click done.
NOTE: You can add multiple NAT services. However, for each NAT service you want to add, you must ﬁrst select
the new NAT service as explained in the preceding paragraphs.
annnNiee "mm" lulcmrlhrlmrr ‘ um}:
it zl- “Ea w raw-35, 1rd. M, m
-—_|_
@ BellSouw
,, '5,.. , a . , , m FostAccess’
Y‘Slﬂnmc’rw ‘iﬁdﬁﬁf ‘ "557353 .. W’ﬁ‘f'" ., ‘7%2%7J .,,‘V""§"°""’> lnternetServioe
mm nwlu
030-300452 Rev A 95 May 2005
WETELI.
User Guide
030-100-152 Rev. A
BellSontherleinkGltewly
6/1/05 - Draft 2
VersaLink Gateway (Model 32 7140
If you have selected a host device and clicked done in the preceding page, the following page will be displayed, It
displays the NAT service that you have added.
‘ BeIISouth‘
um. , D f FuslAccess'
f‘ _ _ TA mamasm
Summary
Mr cullllmlmllnn
Snag-Nun- sﬁuslm .
“bunt" clams-w”:-
; an“, N.“ mm. m. mun-mu
l n.“ v]. mu m nyvumm 51-482
use: Am urn Mm:
m min Mar-”Imam
To View the details of a NAT service that you have added, click the details button adjacent to the desired NAT
service. The following page will be displayed It shows the details of the selected NAT service. Click the Back
buttdn to return to the NAT Conﬁguration page.
BeIISdulh‘
p . FuslActess‘
“571", 421251, lnlemetsefvice
Service Details
Service Name The NAT service you selected
Txpe The type of NAT service
Protocol Trafﬁc going from the modem to these parts
Global Port(s) The txpe of Protocol used to run this NAT service
Base Hnst Port Trafﬁc going from the modem from these ports
USO—300452 Rev. A
96 May 2005
4/
w-TELL
User Guide
nan-300451 Rev. A
BellSnntherleinkCntewly
6/1/05 — Draft 2
VersaLink Gateway (Model 327W)
11.3.2 Deleting NAT Services
To delete a NAT service, at the NAT Conﬁguration page click the delete button adjwent to the desired NAT
service.
BeIISDuth'
FaslAmss’
“Swan-01A “um/v5- “ v _ 3- ,7 vmemmew i.
v ntcnmlrjunlllnn
w" W" ,ﬁhhﬂlhﬂ .
mm ”mm
mr rmumw, fﬂ
Aﬁer the NAT service has been deleted, the following page will be displayed.
FuslAmss‘
h inumgvsewme
m mum-4mm-
s-~=- um [Mm—11
mm umm
mm mm mm mm mom/1n-
wssc in mm W 1:2 £515
W m. mm
BeIlSouth’ ‘
030-300452 Rev. A
97
May 2005
' 030400452 Rev. A
BellSouthVersaLlnanlewny
WEE“ 6/1/05 - Draft 1
User Guide VersaLink Gateway (Model 327140
11.3.3 NAT Table Monitoring
The N AT Table Monitoring feature enables all trafﬁc on the pans to be monitored.
11.3.1] Enable NAT Table Monitoring
To enable NAT Table Monitoring, at the NAT Conﬁguration page, click on the enable button adjacent to NAT
Table Monitoring.
d BeIISouth°
mm ‘ D, _ FustAccess’
“W2?” I ‘ m "Wm" InternetSen/ice
mu canngmuon
SW“ NW“ SdluASilv-w v
w 09mm: 04mm 9mm
x m
1 V,“ _
snrvlu Nam. alrvlu Mud! Hos! mm \
WEE: um um Dynamic ml w.
u m 5m.
NAT mm Mnnimn‘nu
If you clicked the enable button, the following pop-up semen will be displayedi Click OK to enable NAT Table
Monitoring.
030-300452 Rev. A 98 May 2005
IBD-SONSI Rev. A
BeIlSonthVerlelnkGatzway
mms — Drill 1
WESTELL
User Guide VersaLink Gateway (Model 327W)
11.3. 3.2 Disabling NA T Table Monitoring
To disable NAT Table Monitoring (if it was previously enabled), click the disahle button adjacent to NAT Table
Monitoring
bl BelISoutho
m, , FustAccess°
ii ii 11d . .
Sumsry 3mm“ “cm v "Mess _ ~mmfas ”MW.“- mmswce
NAT cnnflqnmtlnn
“Wham“ SelszseM'ne ,- 4215 “M
"' Denotes (115mm Mice
szrvlcz Name senile: mm Has! Davlcn
msz: ALG chm: Dynamic Ana-w-
NAT Yable Monitoring mm,
If you clicked the disable button, the following pop-up screen will be displayed. Click OK to disable NAT Table
Monitoring.
of! Internet Explore!
030-300452 Rev. A 99
May 2005
4 “JO-300452 REV. A
BellSouthVersaLinkCnteway
WESTELL 6/1/05 - Draft 2
User Guide VersaLink Gateway (Model 327W)
11.3.4 Static NAT
Static NAT enables you to conﬁgure the VersaLink to work with the special NAT services. This page enables you to
select an IP address as your default NAT destination. When the modem is conﬁgured for Static NAT, any
unsolicited packets arriving at the WAN will be forwarded to this device. This feature is used in cases where the
user wants to host a server for a speciﬁc application.
11.3.4.1 Enabling Static NAT
STOP: IfStatic NAT is enabled, all unsolicited inbound traﬂic will be sent to the device that you select as the Static
NAT device. Static NAT and IP Passthrough are mutually exclusive features. IP PassthrougthMZ Conﬁguration
must be disabled (if it has been previously enabled) before you conﬁgure static NAT. Refer to the section 1 1.2.1.2
(Disabling IP Pussthrough/DMZ). Aﬁer you have disabled IP Passthrough/DMZ and rebooted your computer, retum
to the Static NAT page by selecting Home Network at the main menu and then by clicking on NAT/Gaming.
To enable Static NAT, click the Static NAT button at the NAT Configuration page. The following page will be
displayed
BellSouth’
FastAccess”
Broadband ’ . ﬁreimllond _
,/ Internet Serwce
Diagnostlrs
static NAT?
set on an 1: mass m be yaw default Nu damnation
math: m7 Device sells-982 v
All unsotldzeﬂ Inbound trafﬁc will! as sent to ma alum device.
Nnu: 5mm NAT and la cassrhmugn avs mutually exclusive fealums.
unable mm
030-300452 Rev. A 100 May 2005
030-300-352 Rev. A
M BellSouthVenaLlnkGateway
wssreu. 6/1/05 43m: 2
User Guide VersaLink Gateway (Model 327W)
At the Static NAT page, choose the desired device from the Static NAT Device drop-down menu, and then click
enable.
G BellSouth"
/ , FnstAccess‘
m... m... . We“... . .
jmw , , ~J5'.‘1255.~. WZ’CE‘; View“ £931; mtemezsarwce
7 l n“
All unsnllnlkad mama tram: wlll an sun! In
um: Slllk an m IP Dlnthxvugh m mull-lily x
The following page displays the Static NAT device as enabled. Ifna devices are enabled for Static NAT, the ﬁeld
adjacent the Static NAT button will be blank.
an.“ nhnuuhcn
n. m m r Ill
é} BeIISouth‘
um mm»: FastAccess'
“mm”. Pf‘ 575°. P“ " Internet Service
NAY cnnligurnllm- l
59W” "a”! SelauAseN’m ~
1 «names am... we.
slruln- Numu E-lvlcu mu. um navlce
1955: Am client Dynamc gm. f“. 4
Bum.
um.
Eniblnd Fur Salli-VBZ
rm rah]; Menu-ﬂing
030-300452 Rev. A 101 May 2005
" ozo-Jnmsz M. A
BuISoumeLlnmmway
WESTELL 6/1/05 — Dun 2
User Guide VersaLink Gateway (Model 327W)
11.342 Disabling Static NAT
To disable Smtic NAT, click the Siatic NAT button at the NAT Conﬁguratlon page.
EeIISouth“
FustAccess‘
_~ Internet Service
rwraw.gg.m.m.. 7
5m" “i"! SnimAsmvm
... Demand“
mu Nnm- man/ll: mm- mm mm;-
wssc ALG Cllml mm
NAT Yibln Murilurinq mm-
lfyou clicked Ihe Static NAT buﬂun, the following page will be displayed Click the disable button to disable Slatic
NAT.
am“: wn u
BellSouth‘ '
, l
Hume Broadband Nome ‘ ﬁrm/land ‘ , ‘ “MAKE” .
W m mm m womcs . ,
,f_ V“ ...3‘“ “N \ ”° ,:.., WNW” J'i‘ff'i‘w gv m, lntermtswce
mm“,
s.“ u, n m m,” m n. m, n-t-mr m “mm
mm: NAT own:- “new ~
Allunsnﬂdlndlnhnund lremnwlll hn mun Inn nhnva aavm.
mus: sun: nu m w msxmugn m mumany mum 1mm:
030-300452 Rev. A 102 May 2005
nan-300452 Rev. A
BelISouthVersaLinanteway
WESTELL A 6/1/05— Draft 1
User Guide VersaLink Gateway (Model 327119
If you clicked disable, the following page will be displayed. (No device is displayed adjacent to the Smtic NAT
butlon)
BellSouth‘
memnum FastAccess’
' Name ' Broadband Home
Summary 1251 Line Nelwark Whales; Passwords fmwﬂ’f: Internet 59mg
MVMWWW WMWMﬁ, WWWJ “WWWWJ Mwwemd -_
semi” "M“ SelenASewiee ‘-
"' Denote: amom arm-o
Service Name Sun/[ca Mada um Devlm
msEc ALG Client Dynurm':
“m.
Deli": (unm 5mm. ‘
NAT ram. Monitoring enable
GEO-300452 Rev. A 103 May 2005
’ 030400452 Rev. A
BeIlSnuﬂtVelenkGath/Iy
WEETELL ﬁll/US — Draft 2
User Guide VersaLin/t Gateway (Model 327W)
If you click the QoS button in the Home Network page, the following page will be displayed. If you change any
settings in this page, you must click the save button to allow the changes to take effect. If you click cancel, the
changes that you have made to this page will not be saved and the previously saved settings will be displayed. lf you
click reset to factory defaults, the page will reﬁ-esh and display the factory default QoS settings.
NOTE: The QoS feature helps ensure data integrity in higb»speed transmissions. (205 provides the capability to
partition network trafﬁc into multiple priority levels or classes of service. Aﬂer packet classiﬁcation, other (205
features can be utilized no assign the appropriate trafﬁc handling policies including congestion management,
bandwidth allocation, and delay measmement bounds for each trafﬁc class. If VersaLink is conﬁgured for
ETHERNET PORT 1, mode the QoS function will not be available You must conﬁgure VersaLink for DSLATM
mode to use this function. Refer to section 10.4 for details. The (208 menu option will not be available if you are in
Bridge Ethernet mode. QoS is only applied to packets being transmitted on the WAN.
G BellSouth‘
Home mm, m. “ , immune B ‘ Names?
35mm some. T“ _. J‘EMM, “ff“ memetSemce
"9999-1" {E““'!.. W , ”77
cream”. .—
“mm mm. .—
angst“...mFu.;;¢.;.'..m..;r.irr*”* ’ ._,,,,,.,,,,,,7,,. ””
qmmmm. r'
mammal", |—_|s,..mm -
Punk mfunﬂnllen m- (uh):
CnmmltI-d Inlnrmltlnn m. (to):
ram Burs! a!" (m):
commit-ton amt six- (ms):
Man qua-ta um
Lulclltv Measurement 5
Int-"w Humid-n]:
m-nw thumb-1 (ms);
w mgmmaunn Enable r
w nwmnm am: 241].
um mm 1m “Mural-ion,
ll
08 Conﬁguration
QDS Enable Factory Default = DISABLED
If this box is checked, Quality of Service (QoS) will be Enabled.
Turbo TCP Enable Factory Default = DISABLED
If this box is checked, Turbo TCP will be Enabled. Turbo TCP does not
function unless QoS is also Enabled
£08 Queue and Filter Conﬁguration
QoS Filter Enable Factory Default = DISABLED
030-300452 Rev. A 104 May 2005
WETELL
User Guide
“31300452 Reta A
BellSnuthVersaLlnkGateway
511/05 7 Draft 2
VersaLirik Gateway (Model 327119
If this box is checked, this will Enable the QoS ﬁlters.
QDS Classiﬁcation
This feature provides the capability to conﬁgure the bandwidth ﬁlter and
queue size for a particular class of service. This menu selects which class of
service is being conﬁgured. Aﬁer packet classiﬁcation, other QoS features
can be utilized to assign the appropriate traﬁ‘ic handling policies including
congestion management, bandwidth allocation, and delay measuremmt
bounds for each trafﬁc class.
Possible responses are:
Best Effort (BE)
Assured Forwarding (AFI)
Assured Forwarding (AFZ)
Assured Forwarding (AFB)
Assured Forwarding (AF4)
Expedited Forwarding (BF)
Network Control EC)
Peak Information Rate (%)
The maximum allowed rate for this priority, expressed as a percentage of
the DSL rate This includes all overhead from the 11’ header to the ATM cell
header. Packets received in excess of this rate are discarded.
Committed Information Rate
(“M
The committed rate for this priority, expressed as a percentage of the DSL
rate. Packets exceeding this rate but below the peak rate may have their
Diffserv code point (DSCP) changed to increase the likelihood of their
being dropped further upstream. The summan‘on of all committed rates must
be less than or equal to 100 percent.
Peak Burst Size (ms)
The interval in milliseconds for averaging the peak offered rate.
Committed Burst Size (ms)
The interval in milliseconds for averaging the committed offered rate.
Max Queue Size
The number of packets that can be queued for this priority.
Latency Measurements
Latency Boundary
This menu selects a boundary for measuring the latency of packets in the
modem. By default counts are kept for the number of packets whose latency
are 0 to 10 ms, 10 to 20 ms, 20 to 40 ms, etc. Changing boundary 5 to 70
ms, for example, would cause counts covering the ranges 40 ms to 70 ms
and 70 ms to 1000 ms instead of the usual 40 ms to 100 ms and 100 ms to
1000 ms. This allows more details to be reported on the statistics page for a
particular latency range (that is, 40 ms to 70 ms).
Possible responses are:
Boundary 1:0 ms
Boundary 2:10 ms
Boundary
Boundary
Boundary 5:100 ms
Boundary 6:1000 ms
Boundary 7:3000 rns
Latency Threshold (ms)
The new value for the latencMundary selected in the menu.
IP Fragmentation Configuration
ll’ Fragmentation Enable
Factory Default = DISABLED
If this box is checked, IP Fragmentation will be Enabled. If Enabled and if
EF packets are being sent, then lower priority packets that are bigger than
the fragment size are:
1) Fragmented in the modem, if the “do not fragment” bit is set to 0 in
the IP header, or
2) Discarded because the “do not fragment“ bit is set to 1, In addition,
and ICMP message is returned to the sender, indicating that the
packets is too big.
(BO-300452 Rev. A
105 May 2005
4/
030400452 Revt A
BelISnutllVerlaLlnkGuteway
wssrm ﬁll/05 7 Draft 2
User Guide VersaLink Galeway (Model 327W)
Fragmentation stops when no EF packets have been seen for the last few
seconds.
Il’ Fragment Size This is the [P Fragment Size.
Possible responses are:
100, 148, 244, 292, 340, 388, or 436
If you made changes to the QoS Conﬁguration page and clicked on save, the following pop-up screen will be
displayed. Click on OK. This will save your new QoS settings.
11.4.1 Advanced
If you click the Advanced button in the QoS Conﬁguration page, the following page will be displayed. This page
enables you to add rules to the QoS Codepointt Click on add rule.
I NOTE: You may add up to 40 QoS eodepoint rules,
linﬁliydnhnhyt
new
i if,
a Bell South”
”m mam m . ”Mum . FuslAcceSS’
‘f‘T'f'W P“? 5!“ “W“ e ff?“ "mm" “W“ Internet Service
No lulu mum
030600452 Rev. A
106 May 2005
WESTELL
User Guide
030400452 Rev. A
BellSollthVersnLlnkGlleway
6/1/05 — Draft 2
VersaLl'nk Gateway (Mada 327W)
If you clicked add rule, the following page will be displayed.
a.....,«,«.gz.....l.m“tummwM...muggy...7 alum
immmrmeswsu-b M”
Bel ISouth
smulganu name WM“; " ﬁrewallond Diagnostics FGSlACCGKtS
”F: f’l'e .,, [TEL w , ms ﬁfﬁ‘ﬁ‘i‘o is-.- “l Internet Serwce
. A“ 5°11, ,, , 7 ,, , , , Ji‘i...
A value (lp addiws, port or pmrocal) of new matches anything (disables matching for that Item). l
A mask of all Zen): ls treated as a mask Dfall ones. '
. oesunarlnn n: Address Desllnatlnn subtler Mask comgamor 1
0.0.0.0 0.0.0.0 Equal ' .
source IP Address Source Suhnot Musk comparator
unun Equal v
DESK nation lP Burt Comparator
n Equal .
Source I? Part Comparator
0 Equal v
Protocol Gnmpnrutur
(DMny ~ Equal .
Class of Service and Drop Priority: —‘|Bm5«m (BE) - '_0
Insert as Rule Number: |_n
. Em'srl'ng rule(s} at or below this one are shifted down. lfruls number rs greater than next
available slot in tabE, rule is insertai at next available slot. l
m. _ all...
Li
Add Code Point Rule
Destination IP Address
The destination IP Address. The Value 0 means that this data item is not
used for matchingpurposes.
Source IP Address The source IP Address. The value 0 means that this data item is not used
for matchingpurpcses.
Destination IP Port The destination IP Port, The value 0 means that this data item is not used
for matchingpurposes.
Source IP Port
The source IP Port. The value 0 means that this data item is not used for
matching purposes.
Protocol
The IP Protocol. The value 0 means that this data item is not used for
matchingpurposes.
Destination Suhnet Mask
The mask for the deslination IP Address.
Source Subnet Mask
The mask for the source IP Address.
Comparator
This determines whether the rule will match a packet whose data equals
the value speciﬁed or will match a packets whose data does not equal the
value speciﬁed.
Possible responses are:
Equal
Not Egual
Class ofServlce and Drop Priority
The new class of service and drop priority. The minimum drop priority
for EF is 6. The minimum drop priority for the AP classes is 2.
030400452 Rev. A
107 May 2005
7 «ten-300451 Rev. A
BeIlSnuthVerleinanteway
6/1/05 — Bull 2
wsrsu.
User Guide VersaLink Gateway (Model 327W)
Insert as Rule Number The rule number that you assign to the rule (0,1,23» etc)
Note: Existing ru1e(s) at or below this one are shifted down. If the rule
number is greater than the next available slot in the table, the rule is
inserted in the next available slot
NOTE: A default mle where all data items have values of 0 will match any packet. Since rules are applied in order
and the process stops with the ﬁrst match, any default mle should be the last rule on the list.
Enter the appropriate values in the ﬁelds provided, and then click save to save the settings If you click cancel, this
page will be reset to the previously saved settings.
”mm,"
& BeHSouth
m. MM, m. « - ‘ FﬂstAccess
Summary mm "mm Air ward: Bursa-15m 4 internetServke
"J: van m 5m“. wwmm; cram mm'aaywyazassr 5:55:56; 70, m: {m}.
”manhunmmwmt
m .| sszsszssn Equal 11
Inurw XP Audrey; Source snhnnt Musk cum avatar
HZ] EBJZS‘ 25525in55 ll Elna] ~
Mam,“ mm.”
m —_;m .
mm,“ mm”
W W .
Pmtnwl camp-ureter
m Equ-l ~
m,» New,
mmmmm n
we mm, mm m mm m m. WWW W, m m
“M. mmmmmxmmm
m m,
If you changed any settings and clicked on save in the preceding Add Code Point Rule page, the following pop-up
screen will be displayed. Click OK to continue.
Microsnltlnlemel «plate!
030-300452 Rev. A 108 May 2005
“Ill-300452 REV. A
BellSnnthVelenantcwﬂy
WEETELL 6/1/05 — Draft 1
User Guide VersnLink Gateway (Model 32 7149
If you clicked 0K in the preceding pop-up screen, the following page will be displayed. Click the Back human to
view the saved rule in the QoS Codepoint page.
NOTE: Aﬁer you have clicked 0K in the preceding pop-up (to save a rule that you have added), the Add Code
Paint Rule page will be displayed with val-m reset to zero. If you want, you may now add another rule and click
save to save the rule, To display the saved rules, click on Back in the Add Code Point Rule page
~Adamdzr‘nlnzRidonmmnnlmmttmlmu v
Jmmwmamwsaw H."
,:J
# Bel ISouth
, , 3
Home Ewudbund Nome w. y \ Firuwullard , , “success
Summary DSllIne Nelwork W =“ , . Passwords Magnum“ Internet Service
Maud caaa paimkula _ ﬂ
A WM (u may. pore orpmtwol] 9mm matches anything {disables matching a: mac [Ml-n}
A mask an" m a mama: 2 ”Elk afallam.
Destinatlun us Address Dastlnatlnn suhnm mask cam aralnr
um ml min Equal v
suuraa w Addrlss mum- Suhnll Musk Cnmpnrulnr
mun mm Euual j
Desklnndun w Pam. cnmpnmlwr
[5 Equal ;
scum; 1»: Pan campnmmr
n Emmi .
Prawn-ll compuratvr
(“l/my - Equal L
Class ar samaa ana Dmp Prlurllv: cams) . “a
his.“ as m. Numhur: ..
among rulers) nor below w: m an; amaaaawn, mula numbnir amour mu" m
was» slot in GHQ, rule is mm at mm avallabls slur.
Ll
030-300452 Rev, A 109 May 2005
nan-300451 Rev. A
BEHSuuthVersnLinkGItewny
W TELL 6Illl5 - Draft 2
User Guide
VersaLin/c Gateway (Model 327W)
If you clicked the Back in the Add Code Point Rule page, the following QoS Codepoint page will be displayed,
You may (1) click the delete button adjacent to the rule that you wish to delete, (2) click on Add Rule to add a rule,
or (3) click on Delete All Rules ta delete all rules in the QoS Codepoint page.
,. lelyvllmllsalasirqnsindc nlnI>Hltrnmlllnlcmzt nu!
liB-Eﬂﬁwimrwkl’b
ii
Nomn
Summary ,
ﬁrewvlwnd
mmrds
Numb?
mrwork
who“
Qns Cndzpnlnt
aux-s m ﬁnds-d In ul-dlrlrvm luv u: ﬁrst match. class and Emu niiﬁrlw lmm'maiimlriu’miw'
mplanl pulsar-s wdlpolnt. lv m1 ml. malnhls,!hln malnulm [5 m lilting-ﬂ.
magnastl'u
BeIISouth“
FastAccess’
lnternet Service
Cnmpnmlnr
nulls pm“ Hlndlrﬂeld value Mask
0: IF Dlsrlmlhn Adams; in mu] 2551551553 Eﬂual
lP Smnc'a Adamss 1.92. mun zsszssasm Equal
[P msn‘naﬂnn Port zn [anal
w sum. pm in Emul
(P mule-ll o Euual
New class=unst Emu
le mp Priority-n
QoS Codepoint
Rules are checked in order fmm top to ﬁrst match. Class and drop priority from matching rule replace packers
Diffserv codepoint. If no rule matches, then codepoint is not changed.
Rule The rule number that you assigned to the rule (0 1,2,3 etc.)
Pkt Header ﬁeld The data item(s) used for matching by this rule,
Value The value of the data item to match
Musk The suhnet mask used for comparing IP Addresses
Comparator This determines whether the mle will match a packet whose data equals the
value speciﬁed or will match 3 packets whose data does not equal the value
speciﬁed,
Possible responses ale:
Equal
Not Equal
030-300452 Rev, A
110 May 2005
use-300452 Rev. A
‘ BellSouthVerﬂLlnkalewly
WESTELL 5/1/05 _ man 2
User Guide VersaLink Gateway (Model 327W)
If you clicked on a delete button in the Q05 Cudepoint page, the following pap—up screen will be displayed. Click
OK to delete the selected rule.
Microsoft Inlemel E
lfyuu clicked on the Delete All Rules button, the following pop-up screen will be displayed. Click OK to delete all
rules in the QoS Codepoint page.
crusoﬂ Inlemet Explorer
USO-300452 Rev. A 111 May 2005
' 030-300451 Rev. A
BellSouaneruLinanteway
wss-rELL ﬁll/as - Draft 2
User Guide VersaLink Gateway (Model 32 7W}
11.4.2 Statistics
To view the QoS Statistics, click the Statistics button in the QoS Conﬁguration page, To clear the statistics, click
on clean Click the Back button to retum to the QoS Conﬁguration pageo
amum 19mm
1m at M m- m M M"
# BeIISouth"
Home manna ' non;- ‘ ' " .' " ﬁreﬁuénd‘ FustAccess
Summary on (me . Network v WWW“ Pass-wards Internet Sen/ks
WW
' ads snaﬁixcs'
; mmu NumharMax Qusu- mm mm Dmppld Pnuklls mun Enquuu-d ”mu comm oupm o-npm Depth
o zoo o o u
l m o
2 sn 0 o o
a so u n n
4 so u n o
s 10 o n u
a in o n n
Qns Fﬂrer statistics
Punk
link mm mm rum Avg DSL Avg pkA
33m, {311 mmgsgmaw gﬂgﬂllg; mm; mm Fllurvklaytnspcrmupar
(m) (ms) “ '" Rauluad Banal; amps pk! “mm
13 Inn in moo moo o n u n o
‘ 1 ion n woo woo n
3 2 ion n woo won a a o n a
3 ion n woo mo 0 u o o o
4 Inn n mm mm 11 o o u u
5 inn 0 mo mo 0 o u u n
a mm n mm mm: o o o o n
‘ quaua Nulﬂmn nmsln inmslo znmnn wmsm mnmsm lmmmslo urgerlhnn
Numhnr mammal! mm; mm; mm; mums lnunms nunnms aunt-m;
‘ n u o n o n a o n
‘ 1 o o v o n u u u
1 2 o n n o n o o o
i a n n n n n a n n
o o n o n n o o o
5 o n n o v o u o
s u n u n n o u o
1 M,
030-300452 Rev. A 112 May 2005
tun-300452 Rev. A
BeuSuuthm-Linkcntewxy
WEETELL 6/1105 —- Draft 1
User Guide VermLink Gateway (Model 32 71W)
If you click the VLAN button in the Home Network page, the following page will be displayed. If you change any
settings on this page, you must click save to allow the settings to take effect. Click reset if you want to reset this
page to the previously saved VLAN settings.
NOTE: IfVersaLink is conﬁgired for ETHERNET PORT 1 mode, the VLAN function will not be available. You
must conﬁgure VersaLink for DSLATM mode to use this function. Refer to section 10.4 for details. The VLAN
menu option will not be available if you are in Bridge Ethemet mode.
BeIISouth"
»
Home smodband Home WM“; Firewalland m, "an,“ FustAccess
Summary, DSLLlne ‘ Network . ‘ Passwords “9 4 , U meme‘ Service
\.~
,, VLAN Enable
VLAN Part cnlwiuu
‘ um mm
1 qu m it;
1 mm Priority 3i
outgulng VLAN Tug i
VLAN Conﬁguration
VLAN Enable Factory Default = DISABLED
If this box is check, VLAN will be Enabled. This will allow VLAN
tagging to occur according to the data port’s conﬁguration.
VLAN Port Conﬁguration
LAN Port This allows you to select the LAN port that you wish to conﬁgure.
Possible responses are:
Ethernet Port 1
Ethemet Port 2
Ethemet Port 3 J
(BO-300452 Rev. A 1 13 May 2005 i,
WETELL
User Guide
(ED-300452 Rev. A
BﬁlSonthVersaLlnkGauway
6/1/05 — Draft 2
VersaLink Gateway (Model 327W)
Ethernet Port 4
W'LAN Port
VLANID
1 through 8
This allows you to assign a VLAN ID to the port.
Possible responses are:
VLAN Priority
This allows you to set the VLAN priority for the port.
Possible responses are:
0 through 7
Outgoing VLAN Tag
This allows you to keep or remove the VLAN tag on the port when data is
outgoing.
NOTE: For VLAN to function properly,
the VLAN ID mustbe set to a value other than ‘1’ in the following VLAN
Conﬁguration page and in the VC 1 Conﬁguration page when you are using the Bridge Ethemet (VLAN Bridge
mode) protocol. Refer to section 104.3 for details on eonﬁguring the VC l Conﬁguration page.
To enable VLAN, click on the box adjacent to the VLAN Enable ﬁeld (a check mark will appear in the box).
Next1 click save to save the settings.
NOTE: If you change the values in the VLAN Conﬁguration page and then click the reset button, the page will
display the previously set values for the LAN Port you have selected. If you change the settings in this page, you
must click save to save the new settings.
in... mm,
Snmmw‘l BSA Line
gargantuan; 7
VLAN (name
vuu mm Cnnflgunﬂinn
um am
vuu m
yum Prlafitv
Dulgulng vun rag
Bel I South'
FusiAccess”
, Internet Service
"m; whim
mug/veins
030-300452 Rev. A
114 May 2005
030600451 Rev. A
M MllSuuthVersnLinkGll‘eway
WESTELL 6/1/05— Draft 1
User Guide VersaLink Gateway (Model 32 7W)
If you click an save, the following pop-up screen will appear. Click OK in the pop-up screen to allow the new
settings to take effect.
Microsoft Internet Eupinlel '
24
lfycu clicked 0K in the pop-up screen, the following screen will be displayed. Click OK.
Micmsnll Inlelnet Expl
If you clicked OK the modem will be reset. After a brief delay, the Home Summnry page will be displayed.
> warning
"mm-g mum,
lm. walk. .
m. mmm 1! mm»; u may w
m- mun-d minus u uh arm.
mmu- um»- mm“ may,
030300452 Rev, A 115 May 2005
’ Mil-300452 Rev. A
BellSouthVenaLlnkGateway
WErEu. 6/1/05 7 Draft 2
User Guide VersaLink Gateway (Model 327W)
If you click the Statistics button in the Home Network page, the following page will be displayed. This page
enables you to view the Ethernet, IP and LAN statistics of your modem. Aﬁer you have viewed the statistitx, click
Ihe Back button to return to the Home Network Statistics page.
BelISouth”
"similar-f D. , FastAccess“
M’W‘" W" 1“ lnlemelSm/lce
Winks:
Emumix
w Adar-SS / ~ me Addr-ss cum-mm. umus Gram-5th"! Wan
mammal nozsamsmzmem Active Ethan-mu
wlml-n
m: Adams: “ll-
11.6.1 Ethernet Statistics
If you click Ethernet in the Hume Network Statistics page, the following page will be displayed.
+ Bellsuumi‘ >
mm m luslAccess
"MW“ "9 t, internal 5mm
mam: smfsncs
‘ mam Imam-(Inn
in Err-r:
x.- Dlsuld mum
x" mm unlwn Uni-"kins
‘ in "mm Suﬁ-ts
m nuns
‘ om Envrs
om mmm pumas
‘ out nu.- "mm “mu
m “Mun "mu
out can:
mm
_ mm“ Maw“ Elmm-lvmx sin-mum: sum-mu Ethan-(Putt
030-300452 Rev. A 116 May 2005
' 030400452 Rev. A
BellSouthersaLlnkGateway
6/1105 — Draft 2
WETELL
User Guide VersaLink Gateway (Model 327W)
Ethernet Statistics
In Errors | The number of error packets received on the ATM port.
LIn Discard Packets The number of discarded packets received.
In Non Unicast Packets The number of nou-Unieast packets received on the ATM port.
In Unicast Packets The number of Unicast packets received on the ATM part.
In Octets The number of bytes received on the ATM port.
Out Errors The number of outbound packets that would not be transmitted due to errors.
Out Discard Packets The number of outbound packets discarded.
Out Non Unicast Packets The number of non—Unicast packets transmitted on the ATM port.
Out Unicast Packets The number ofUnieast packets transmitted on the ATM port.
Out Octets The number ontes transmitted on the ATM port.
Interface Descriptions The name of the Ethernet interface.
11.6.2 11> Statistics
If you click [P in the Home Network Statistics page, the following page will be displayed.
IP Interfaces displays information on all IP interfaces. Network Routing Table displays information on all
network routes. Host Routing Table displays information on all local network routes.
NOTE: The WAN IP Address will display “Down,” and the IP Statistics will be unavailable if VersaLink is in
ETHERNET PORT 1 mode.
BellSouth“
mayor n . r um ' . . FustAccess
summm mun: New. Wm“ gm”. . magnum lntemetswce
“mew”... ., ,./ t.,.....__.wv Mammy tom—MN. hamwﬁ
"3 statistics
wm 19 Address in.is.su.5
Gateway w Address
Drlmnrv nNs:
Secondary nst
Frlmnrv um um.
summary DNS mm!
.2
mpmmlmm
arrhwestelldmm
yr» lnlzrtuccs
Network Rnutlvm raulu
D-sllnnlan Netmusk Gateway
u.u.n.n an.” missus
iguana 255.255.2553 lemmas-
Host Ranting ram:
”T' “inseam ""'
Ina
mu
inn
030600452 Rev. A 117 May 2005
“JO-300452 Rev. A
BeIlSuuthVeruLil-kcatewny
ﬂlllﬂS— Draft 2
WEBTELI.
User Guide VersaLin/t Gateway (Model 32 7W)
[P Statistics
WAN IP Address Displays the WAN IP address that your modem is on
Gatewa IP Address Dis la the modem’s atewa IP address
Primary DNS Displays the primary DNS address
Seeondag DNS
Displays the secondary DNS address
Primary DNS Name Name of primary DNS sewer
Secondary DNS Name Name of secondary DNS sewer
IP Interfaces
The list of active interfaces on the Modern and their IP and Netmask addresses.
Address The IP interface address.
Netmask The 1? interface netmask address.
Name The IP interface name.
100 is the loopbaek interface.
ethO, ethl, ech, or etl13 is the local LAN interface.
mainPPP is the WAN Aprotocol interface.
Network Routing Table
The list of“ network routes. These can be either routes for directly connected interfaces or static routes.
Destlnatlon Address The IP address or subnet of the Route.
Netmask If the Route is a network route, netmask is used to specify the subnet mask.
If the Route is a Host route, then the Host Route check box is used.
Gateway Indicates were to send the packet if it matches this route.
Interface Indicates were to send the packet if it matches this route.
The list of host routes. A host route
Host Routing Table
is an IP route with a 32-bit mask, indicating a single destination (as opposed to a
subnet, which could match several destinations.)
Destination Address The IP address or suhnet of the Route.
Gateway Indicates were to send the packet if it matches this route.
Interface Indicates were to send the packet if it matches this route.
030-300452 Rev. A
118 May 2005
" mesons: Rev. A
M BelISnuthVersnLlnkGateway
WESTELL 6/1/05— Draft 2
User Guide VersaLink Gateway (Model 327W)
11.6.3 LAN Statistics
If you click LAN in the Home Network Statistics page, the following page will be displayed.
BeIlSouth"
DHCP start Address 192.16 1.1
~ s ~ t . , . °
' Home amalgam Home Winks; ; . Hrewultand Diagnostics FustAccess
Litrmmaryw . DSlee . _ Network WW ‘ Passwords j g InlemelServtce
l [AN 556535; ., 7 H 51“ a,
l mndemrp Address 192.155.1254
1 DHCP NetMask 255.255 255.1:
anon End Address 192. Jess
DHCP server status om
nucp server Private
find Eddrés? w“ MAC Address Name status
‘ 192 159 1.19 un:5u:da:b2:d§:f1 sane-932 Active
LAN Statistics
Modem IP Address Displays the Dual Connect Modem‘s IP address
DHCP NetMask This setting speciﬁes the subnet mask to use to determine if an IP address
belongs to your local network.
DHCP Start Address Displays the starting DHCP Address.
Dynamic Host Conﬁguration Protocol automatically assigns IP addresses to
devices added to our LAN (Local Area Network).
DHCP End Address This setting speciﬁes the end address of the IP address pool used for automatic
conﬁguration of local devices.
DHCP Server Status Displays the status of the DHCP server
Possible responses are:
0N=DHCP sewer is enabled
0FF=DHCP server is disabled
DHCP Server Displays the status of the DHCP sewer
Possible responses are:
Private = DHCP server is enabled
OFF = DHCP server is disabled
Devices on LAN
Displays information about the devices on the LAN
030-300452 Rev. A 119 May 2005
' 030600451 Rev. A
BellSauthVernLinkGlteway
6/1/05 — Draft 1
WEsTEu.
User Guide VersaLin/t Gateway (Model 327W)
If you click on Wireless at the main menu, the following page will be displayed. This page enables you to set up the
wireless network settings of your modem. To conﬁgure the wireless settings for VersaLink, click on the
Conﬁguration button at the right of the page.
IMPORTANT: If you are connecting to the modem via a wireless network adapter, the service set ID (SSID) must
he the same for both the Westeil modem and your PC’s wireless network adapter. The default Network Name
(SSID) for the modem is the serial number of the unit located below the bar code on the bottom of the unit and also
on the Westell shipping canon. (The SSID displayed in the following page is WEST0719; however, your SSID
might differ from the SSID displayed in this page.) To communicate with the modem, the PC’s wireless network
adapter must be conﬁgured with the SSID and pre—defmed WEP Key 1 before you begin the modem’s Customer
Information setup and conﬁguration procedures. Locate and run the utility software provided with your PC’s
Wireless network adapter and enter the SSID value. Later, for privacy, you should change the Network Name
(SSID) value in the Wireless page to your desired value.
BelISou‘thG
FostAccess”
Home madam: ‘ ’ ﬁrewall and _
lnternet Service
summary DSlee _ . Nsxwwds , Dingnnshcs
. caniimm
’ w|ra|Ess Dpamtlun
Network Name (ssm) wtsmm
channel 6
Mode Mixed
4x support Disabled
9, ,, ,, Asshtadﬁﬁ,
erelass seumty
was; exam; ' ' W WivW
Key 1 easezaeeeaaaedsehavmenei
1 MM: Address Filtering Dlsahlad
Wireless
Wireless Operation Factory Default: Enable
Displays the current setting of the modern’s wireless operation.
Network Name (SSID) This string, (32 characters or less) is the name associated with the modem. To connect
to the modem, the SSID on a station card must match the SSID on the modern. (Note:
If the SSID on a modem is hidden, at the station card you must manually type the
SSID of the modem to which you are trying to connect.)
Channel Factory Default = 6
The modem transmits and receives data on this channel. Station cards do not have to
030-300452 Rev. A 120 May 2005
M.
030400452 Rev. A
BellsouthVersaLinkGateway
WETELL. 6/1/05 - but: 1
User Guide VersaLink Gateway {Model 32 71719
be set to the same channel as the AP; the station cards scan all channels and look for
the modern with the correct SSID.
Mode Factory Default 2 Mixed
This setting allows station to communicate with the modem.
Possible responses:
Mixed: Station using 802.11b or 802.11g cards can communicate with the modem
using both 11b and 11g rates.
Ilb only: Stations using 802.1111 or 802.11g cards can communicate with the modem
using only llb rates.
11g only: Only stah'ons using 802111g cards can communicate with the modem.
4x Support Factory Default = Disable
If enabled, 4X support provides additional algorithms for increased throughput with
station cards that support 4x.
Hide SSID Factory Default = Disable
If Enabled, the modem will not broadcast the SSID. Stations must conﬁgure the SSID
to match the Network Name (SSID) in order to connect to the modem.
Wireless Security
Wireless Security Factory Default=WEP
Possible Responses:
Disabled: No security is used.
WPA—PSK: WPA encryption methods are used to encrypt and secure the connection
and the data being sent to and from the modem.
WEP: WEP encryption used to secure the data being sent to and from the modern;
when WEP is enabled, the risk of someone nearby accessing the modem is minimized.
Key n Factory Default = Key 1
(where n is l - 4 for WEP and is This information will only be displayed if Security is Enabled. This is the key that is
”Mk R" WPA'PSK) being used for the security mode selected above.
MAC Address Filtering Factory Default = Disable
If Enabled, only the stations in the MAC Filter Table can connect to the modem.
030-300452 Rev. A
121 May 2005
‘ 030600151 Rev. A
. BellSnutllVersnLinanteway
WESTE 6/1/05 — Bull 2
User Guide VersaLink Gateway (Made! 327W)
If you click the Conﬁguration button at the Wireless page, the following page will be displayed. Enter the desired
values in the ﬁelds provided, and then click save to allow the settings to take eﬁect. To edit the MAC Filter Table,
click the edit button. To reset this page to the previously saved settings, click reset.
BeIISouth°
N « , ,, m, , _ ~ FostAccess
Sunfmmrirv ' . WWW $537":qu “mm" , Internet Service
‘ere‘less Conﬁguration; 7 7
wlralass Opsrdtlnn
N-twnrknumu (5er)
Channel
man:
an Support Disabled ~
Hlda ssm Disabled v
Wireless Security
wlrelass sac-mm m
Aulhamlmllon wpa Open System v
Kev mm W
Kay 1 smzaasmmsahannwai
Key 2 m—
Kay 3 an 3h727e-Bac7hlu5537c7179
Kay 4 5557855755IBM|5l9833a74du
64 bit (5 tlxt or m hexadecimal digits)
‘WEP keys: HE hit (13 (”ft or is hexadecimal digits)
255 blt 29 text or so haxadectmal digits)
mu: Addmss Fill-ring Dumas
me Fllzer nhl- nﬂ
Wireless Conﬁguration
Wireless Operation Factory Default = Enabled.
Displays the current setting of the modem's wireless operation.
Network Name (SSID) This string, (32 characters or less) is the name associated with the modem. To connect
to the modern, the SSID on a station card must match the SSID on the modem. (Note: It‘
the SSID on a modem is hidden, at the station card you must manually type the SSID of
the modem to which you are trying to connect.)
Channel Factory Default = 6
The modem transmits and receives data on this channel. Station cards no dot have to be
set to the same channel as the modem; the station cards scan all channels and look for
the modem with the correct SSIDA
030-300452 Rev. A 122 May 2005
4/
030400452 Rev. A
BellSnuthVersaLinkGateway
6/1/05 — DH“ 2
WETELL
User Guide VersaLink Gateway (Model 327W)
Mode Factory Default = Mixed
This setting allows station to communicate with the modem.
Possible responses are:
Mixed: Station using 802.111) or 802.11g cards can communicate with the modem using
both llh and 11g rates.
1 1h only: Stations using 802.111: or 802.11g cards can communicate with the modem
using only llb rates.
11g only: Only stations using 802.11g cards can communicate with the modern.
4x Support Factory Default = Disable
If enabled, 4X support provides additional algorithms for increased throughput with
station cards that support 4x.
Hide SSID Factory Default = Disable
If Enabled, the modem will not broadcast the SSID. Stan'ons must conﬁgure the SSED to
match the Network Name (SSTD) in order to connect to the modem.
Wireless Security (if WEP is used)
Wireless Security
Factory DefauIFWEP
Possible Responses:
Disabled: No security is used.
WPA-PSK: WPA encryption methods are used to encrypt and secure the connection and
the data being sent to and from the modem.
WEP: WEP encryption used to secure the data being sent to and from the modern; when
WEP is enabled, the risk of someone nearby accessing the modem is minimized.
Authentication Type
Factory Default = Open System
Possible responses:
Open System: Open System authentication is the default selection, WEP encryption is
not used for association.
Shared Key: WEP encryption is used for the association process and only stations
having the correct key can connect to the modem.
Key Select
Factory Default = 1
Select Key 1 to Key 4 as the WEP key to be used. The key position must he the same in
both the modem and the station.
Key n
(where n is l- 4 for WEP and
is blank (or WPA—PSK)
The WEP key is treated as either text or hexadecimal (hex) characters. The number of
characters is based on the key size selected. The key size 64 bit is either 5 text or 10 hex
characters, 128 bit is either 13 text or 26 hex characters, and 256 bit is either 29 text. or
58 hex characters. Hexadecimal characters are 0-9 and AF (or a-t). This key must be
the same in both the modern and the station. Some station cards use a “Pass Phrase."
This is not the same as “text" and should not be used.
MAC Address Filtering
Factory Default = Disabled
If Enabled, only the stations in the MAC Filter table can connect to the modem,
MAC Filter Table
This table enables you to add, edit or delete MAC addresses of stations that are allowed
to communicate with the modem.
030-300452 Rev. A
123 May 2005
WESTELL
User Guide
030400452 Rev. A
BellSouthArsaLlnanteway
ﬁlllﬂS — Draft 2
VersaLin/t Gateway (Model 32 7 W)
chum-ct
Made
4x Support
NIH. ssiD
wpa shared Kay
MAC Flklr Tabla
Wireless Conﬁguration
wlrelass opal-mm.
Network Name (saw)
Wirelessgecunty
Wlmlass Sammy
wm Gmup link-v lnllrval
MAC Addras; Filtering
BellSouth“
FustAccess“
Internet Service
Broadband Home Firemllond
3500
must be a m as text characters or 54 hexadecimal digits in length
Disabled v
‘WPA kay:
Wireless Operation Factory Default = Enabled.
Displays the current setting of the modem‘s wireless operation.
Network Name (SSID) This string, (32 characters or less) is the name associated with the modem. To connect
to the modem, the SSID on a station card must match the SSID on the modem. (Note: If
the SSlD on a modem is hidden, at the station card you must manually type the SSlD of
the modem to which you are trying to connect.)
Channel Factory Default = 6
The modem transmits and receives data on this channel. Station cards no dot have to be
set to the same channel as the modem; the station cards scan all channels and look for
the modem with the correct SSID.
Mode Factory Default = Mixed
This setting allows station to communicate with the modem.
Possible responses are:
Mixed: Station using 802.1 lb or 802.1 lg cards can communicate with the modem using
both llb and llgrates.
llb only: Stations using 802.111) or 802.11g cards can communicate with the modem
using only llb rates.
11g only: Only stations using 802.1 1g cards can communicate with the modem.
4x Support Factory Default Disable
If enabled, 4X support provides additional algorithm for increased throughput with
station cards that support 4x4
Hide SSID Factory Default = Disable
If Enabled, the modem will not broadcast the SSID. Stations must conﬁgure the SSID to
030-300452 Rev. A
124 May 2005
use-30045: Rev. A
. BellSnnthVemLinkawny
WETELL 6/1/05 — butt 2
User Guide VersaLin/c Gateway (ModeI 327W
match the Network Name (SSID) in order to connect to the modem.
Wireless Security (ifWPA-PSK is used)
Wireless Security Factory Default=WEP
Possible Responses:
Disabled: No security is used.
WPA-PSK: WPA encryption methods are used to encrypt and secure the connection and
the data being sent to and from the modem.
WEP: WEP encryption used to secure the data being sent to and from the modem; when
WEP is enabled, the risk of someone nearby accessing the modem is minimized.
WPA Shared Key This string (8 to 63 characters of 64 hex characters) is the key used for encrypting
packets being sent to and from the modem This key must be the same in bath the
modem and the station.
WPA Group Rekey Factory Default 2 3600
Interval The number of seconds between rekeying the WPA group key A value of 0 means that
rekeying is disabled. The Shared Key is the initial key and new keys are created and
used, based on that key, at each Riey Interval.
if you clicked edit, the following page will be displayed. Click the add button to add stations to the MAC Address
table, and then click save to save the settings. To add more entries, click the add button. When you have finished
adding entries, click the box adjacent Enable MAC Address Filtering (a check mark will appear in the box). Next,
click save to save the settings.
awe“. mu: Adda-r: ram um um» him. my”,
ll
BelISouth°
FastAccess°
lnternel Service
Home Broadband ‘ ﬁrewalland
Summary . usttim , Passwords j
Diagnostics
wireless Mac Address Elite; rat-E
Enable MAC Address Filtering
when the Mac Address Fllter is enabled, nnlv the stations
that are In thls table, and set m 'Allnwed', will a. nceopted.
All others will be blocked.
currently the Mac Address table is amptv.
can
030400452 Rev. A 125 May 2005
030400451 Rev. A
BellSouthVersnLlnkG-leway
WETELI. 5/1/05 —Drzrt 2
User Guide VersaLin/c Gateway (Model 327 W)
If you clicked save in the Wireless Conﬁguration page, the following pop~up will be displayed. Click OK to
continue.
M mson Intemet Explorer . EH
/ e»
If you clicked the add button in the Wireless MAC Address Filter Table, the following page will be displayed.
Aﬁer you have entered the desired MAC Address settings, click save to save your settings.
BelIScuth‘
”mung: my _x FuslAccess
Home
"mm internal Service
mm Alma -
m: m."- ﬁnmnn um
sum.- Name
030-300452 Rev. A 126 May 2005
nan-300452 Rev. A
BellSouthenaLinkGameway
WESTELL cums — Draft 2
Uxar Guide VersaLz‘nk Gateway Model 327W)
If you clicked save, the following page will be displayed. This page enables you to add, editor delete stations at the
MAC Address Filter table. Aﬁer you have made the desired changes to this page, click the salve button to allow the
changes In take effecti
BelISouth’
m, ~ , m. \ ~ FuslActess‘
ﬁrm 13531, ﬁwﬁfi feet: mmm
Wireless me Injury
emi- MAC muunrm-mg r v we
Whnn in. me Addy-s: nun ls mun-a, unly m mum
mu m In my; mm, mu m lo‘Allmd', will u. swept“. ‘
All my.“ wIII b- Masai
Allowed oomnmmnmnumn
030-300452 Rev. A 127 May 2005
030-300452 Rev, A
BellSouthVertaLinkGateway
611/05 7 Dr!“ 2
WESTELL
User Guide
VersaLin/r Gateway (Model 327W)
If you click the Statistics button at the Wireless page, the following page will be displayed. This page provides
information about your modem’s wireless connection. To clear the statistics in this page, click on clear.
a mum.
wireless Eara'ihrnrma'
N-twork Nemn(SElD)
FW vat-stun
unlcnst Frames
Multlnust Frames
1 Fragments
umppsd Frames
Frames elm one or mura rltrles
Bmldband '
on t' 9
an.“ MAC Address (ussm)
Cnmmuniml n slellstlns
BeIISouth“
. FustAccess”
InternetService
' ﬁﬁmfﬂ Diagnostics
wssrnng
us:ou:zs:ss:unzai
our in
175595
17ﬁ~94
Wireless Card Information
Network Name (SSID)
This string, (32 characters or less) is the name associated with the Access
Point (AP). To connect to the AP, the Service Set ID (SSID) on a Station
card must match the SSID on the AP.
802.11 MAC Address (BSSID)
This is the Media Access Controller address of the APA It is used as the Basic
Service Set Identiﬁer (BSSID).
FW Version
This is the Network Interface Card Identiﬁer. It uniquely identiﬁes the
hardware platform of the AP. This is used with other information to
determine if the inserted card can be used as an AP, and if so, the version of
AP ﬁrmware to be used. Not all makes of wireless station cards can be used
as an AP.
Communication Statistics
NOTE: Data preceded by OUT pertain to transmissions ﬁom the VersaLink to a station; VersaLink is the source.
Data preceded by [N Eertain to data received by VersaLink; VersaLink is the destination.
OUT-Unionist Frames
The number of successfully transmitted frames whose destination address
was a single station; not necessarily the same station, but to any single
station as opposed to a transmission that multiple stations would receive-as
in the case of broadcast message.
OUT-Multieast Frames
The number of successﬁilly transmitted frames whose destination address
030500452 Rev. A
128 May 2005
030400452 Rev. A
BullSouthVers-LInkGutewny
wan-Eu. 6/1/05 - Draft 2
User Guide VersaLr'n/r Gateway (Model 32 7119
was a multicast address (received by more that one station): not necessarily
broadcast to all stations, but more than a single station. Broadcast messages
are included in the count.
OUT-Fragments The number of successful transmissions made. This will typically be greater
than the sum of the Unicast and Multicast frames because large frames are
broken into multiple transmissions. The number of fragments per frame is
based on the Fragmentation Threshold setting (not user-conﬁgmble).
OUT-Dropped Frames, too many
retries
The number of frames that did not transmit due to the short or long retry
limit being reached because no acknowledgement or CTS was received.
OUT-Frames after one or more
retries
The number of frames that successfully transmitted aﬁer more than one
retry. Any fragment of a frame that required multiple retries would
increment this counter for the whole frame.
IN‘Unicast Frames
The number of successfully received ﬂames whose destination address was a
single location, not necessarily the same location, but to any single location
as opposed to the broadcast address.
IN~MuItlcast Frames
The number of successfully received frames whose destination address was a
multicast address. Broadcast messages are included in this counts
IN-Fragmcnts
into multiple transmissions. The number of fragments per frame is based on
the Fragmentation Threshold setting (not user—configurable) on the source
station.
IN-Dropped Frames
The number of frames that were not received by VersaLink due to the short
or long retry limit being reached because no acknowledgement or CTS was
The number of fragments successfully received. This may not be equal to the
sum of the Unicast and Multicast frames because large frames are broken
received.
Wireless Stations List
The current transmit and receive rate.
Station This number indicates the order in which the stations are first accessed by
VersaLink.
MAC Address The Media Access Controller Address assigned to the station. |
State The current state of the negotiation between the station and VersaLink. 1
Active Rate
030300452 Rev. A
129 May 2005
/ 030500451 Rev. A
BellSoIlﬂIVeruLlnkGatewny
WESTEJ. 6/1/05 —Draft 2
User Guide VersaLin/c Gateway (MadeI 327W)
If you click on Flrewall and Passwords at the main menu, the following page will be displayed. This page enables
you to set up your ﬁrewall and password settings. To conﬁgure the settings, click on the desired submenu option at
the right of the page. Aﬁer you have completed a submenu conﬁguration, click the Back button to return to the
Firewall and Passwords Status page.
Bel ISouthg
Bmodlgond ‘ . ﬁrewultand ’ Diagnostics FGSlACtess
”5971- ~ - . “Mm” ‘ Internet Serwce
Firewall and Password ' . 7 ,, '. quwgﬁéﬁ
Am“ y 11: Funnies/g;
Level _ um Gummy)
Admln Password sot Hanwmﬁll
hrmvnll lag
Firewall and Password Status
Active Factory Default = ON
If OFF is digplayed, ﬁrewall securig has not been activated.
Level Factory Default = Low
The security level of your ﬁrewall.
Possible responses are:
High = High security level only allows basic Internet functionality. Only
Mail, News, Web, FTP, and IPSEC are allowed. All other trafﬁc is
prohibited.
Medium = Like High security, Medium security only allows basic Intemet
functionality by default. However, Medium security allows customization
through NAT conﬁguration so that you can enable the trafﬁc that you want
to pass.
Low = The Low security setting will allow all trafﬁc except for known
attacks. With Low security, VersaLink is visible to other computers on the
Internet.
030-300452 Rev. A 130 May 2005
WESTELL
User Guide
0304500452 Rev. A
BellsouthVemLinkGaleway
ﬁll/05 — Drlfl 2
VersaLink Gateway (Model 32 7m
None : Firewall security is not activated.
Custom = Custom is a very advanced conﬁguration option that allows you
to edit the ﬁrewall conﬁguration directly. Only the most expert users
should try this.
Admin Password Set
Factory Default = NONE
The gassword used in the administrator’s login.
USO—300452 Rev. A
131
May 2005
030400452 Rev. A
BellsouthVersaLinkGlteway
W‘TELI. WINS — Draft 2
User Guide VersaLink Gateway (ModeI 327W)
If you click Security Level/Remote Logging in the Firewall and Password Status page, the following page will
be displayed. If you change any settings in this page, you must click save to allow the settings to take effect.
NOTE: Westell recommends that you do not change the settings in this page. If you need to reset the modem to
factory default settings, push the reset button on the rear of the modem. The Security Level/Remote Logging menu
option will not be available if you are in Bridge Ethernet mode.
BelISouth°
Home ' omoooond ' Firewollund ' Diagnostics FustAccess
5mm” D“ “m ‘ .”"‘.‘*’”’"" lntemet Serwce
Security Level
control outbound (731W: (fared nom Within the local network.
Inbound o-emo may be controlled by conﬁgilnng Port meamlw.
only allows the fallﬂ'wlng outbound protocols: HTTP, FTP, POM, SMTH
r ”19“ [MAP (Mas-
. vs. 0945, mws. "7556 m3, lasso Esn, NNTP
Allows a! trafﬁc to pass but plot-ﬁts against attacks uiiiizod by the
F “W fullnwinq pmluculs: NETBIDS, nus, EMAP, SMMF’, LDAP
l r Medium some as high but allows you to select inbound and outbound services
i rirowoii is off (no security provided)
Custom settings
Security Level
High High security level only allows basic lnternet functionality. Only Mail, News, Web,
FTP and IPSEC are allowed. All other trafﬁc is prohibited.
Medium Like High security, Medium security only allows basic Internet functionality by
default. However, Medium security allows customization through NAT conﬁguration
so that you can enable the trafﬁc that you want to pass.
Low Factory Default = Low
The Low security setting will allow all trafﬁc except for known attacks, With Low
securi VersaLink is visible to other computers on the Internet.
None Firewall is disabled. (All trafﬁc is passed)
Custom Custom is an advanced conﬁguration option that allows you to edit the ﬁrewall
conﬁguration directly. NOTE: only the most advanced users should try this.
Remote Logging
Enable Factory Default = Disable
USU-300452 Rev. A 132 May 2005
030-300452 Rev. A
‘ BellSouthVenaLlukG-teway
WESTELL 6/1/05 - mm 2
User Guide VersaLink Gateway (Model 32 7W)
If enabled, VersaLink will send ﬁrewall logs to a syslcg sewer.
Remote ll’ Address The IP address of the syslog server machine to which the diagnostics logs to be sent.
If you have selected “High" or "None” at the Security Level page, the following popup screen will be displayed if
you click the Advanced button. Click OK in the pop-up screen to return to the Security Level page.
Note: If you selected “High” or “None“ at the Security Level page, you will not have access to the advanced
ﬁrewall settings or the Firewall Rules page. The advanced ﬁrewall settings can be accessed only when the ﬁrewall
is set to Medium, Low, or Custom.
If you click Advanced in the Security Level page (and the security level is set to Medium, Low, or Custom), the
following page will be displayed. Entered the desired setting in this page, and then click save to allow the settings to
take effect. To restore this page to the factory default settings, click restore to defaults. Click cancel to cancel any
changes that you have made to this page.
WARNING: Modifying the setting on this page can impact the ability of computers on the local network to access
your broadband connection. Modiﬁcations may also affect bmadhand-enabled applications and services mnning on
the local network.
.:I
BeIlSouih‘
FnstAccess”
. lntemet Service
want "mm: Magnet.
>>>> WARNmG > dnn=
(run but! 51 » an“
drop preteen me, >> um 4 mm: Essay: n um m
nulunxnuulmnr
m, pxncnunl m, n, ma: tnmmmsnz » am, alert. 4 ﬂ
030400452 Rev. A 135 May 2005 i
' 030400452 Rev. A
BellSnllthersaLinkcatewny
WEETEJ. 6/1/05— Draft 2
User Guide VersaLink Gateway (Model 32 7 W)
If you select Inbound, this will restrict inbound traffic from the WAN to the LAN. Selecting Outbound will restrict
oulhound traﬁic from the LAN to the WAN. Select a setting and then click Apply tn apply the new settings.
BellSouth"
FustAccess‘
lnlernel Service
Mumv Broadband “745,525“ r MM”, Egg/£5524 95mm“
mm m- uu m
w, pznuear w, m pm 53 » can
u.“ Manuel m, m- ,on n » um
nun-saunas»
my “mm is» » mu 4 mm "tuba: 1. m m
mlcnran'mvnr
m, pxulntwl m, u m "mm-am >> um, nm 4
am M. New
If you clicked npply in the User Deﬁned Firewall Rules page, the following screen will be displayed. Click OK to
continue.
MICIUSD" Inlcmel Ex lu
If you clicked save in the preceding Firewall Rules page, the following screen will be displayed Click OK to save
these ﬁrewall rules to ﬂash and switch your security level to “User"?
030-300452 Rev. A 136 May 2005
ozoonmsz Rev‘ A
W BsllSouthzusLinkG-tewny
wears”. sums - Draft 2
User Guide VersaLink Gateway (Model 327W)
if you click the IP Passthrough button in the Firewall and Password Status page, the following [P
Pussthrough/DMZ Conﬁguration page will be displayedi This page enables you to select the device on your LAN
that will share your single static IP address. Refer 11.2 to section for instructions on conﬁguring 11’
Passthrough/DMZ.
BOTH: The [P Passthrough/DMZ menu option will not be available if you are in Bridge Ethernet mode,
BeIlSouth"
FustAccess“
timudqond v
,' Internet Servwce
Dst (me
Please select which dam will share your public IP address.
lf'tltar conﬁgmedpc'ix selected, a IocaIPCmuxt bemanua/ly conﬁgured to use mepubh'clﬂ
address.
wm w Address: m.1e.su,s
Unerivglned PD
“Hess:
w Passlhmugh is currently disabled.
030-300452 Rev. A 137 May 2005
USO—300452 Rev. A
. BellSollthVerﬂLinkCateway
WETE 6/1/05 — Draft 2
User Guide VersaLink Gateway (Made! 327W)
lfyuu click the NAT/Gaming button in the Firewall and Passwords Status page, the following NAT
Cnnﬁguratlon page will be displayed. The NAT Conﬂgurntion page enables you to set up NAT services for your
madam. Refer to section 11.3 for instruetions on conﬁguring the modem’s NAT/Gaming functions.
NOTE: The NAT/Gaming menu option will not be available if you are in Bridge Ethemet mode.
BellSouth’
. . FustAccess’
may"??? , InlemelService
Nam Broadband
Summary us! Line
ﬁrewall and
szswords
. NAT Cull'igurulinn
"W”, ,,,,,,,, V... ”ms. mi
Sen/mu Name Sigmund“ v 11“ m “it:
w Denotes cmom mica
nan/Inn Name sarvlcn Mada um D-vlu
lPSEC ALA Chant Dynamv’c j‘mu'u
NAT Conﬁguration
Service Name A drop-down menu ofNAT (Network Address Translation) services that yeu
can select fmm when you are ready to conﬁgure your modem for NAT service.
NAT Table Monitoring Factory Default = Disabled
If Enabled this feature will monitor trafﬁc on the ports.
030-300452 Rev, A 138 May 2005
030300452 Rev. A
Bellsanthers-LlnkGltzwny
WESTELJ. 6/1/05 - Draft 2
Urer Guide VersaLink Gateway (Model 3271719
If you click the Password/User Admin button in the Firewall and Passwords Status page, the following Password
page will be displayed After you enter your data into the appropriate settings, click on change to change the
administration name and password. Click clear to clear the values in this page.
NOTE: This page will enable you change only the administration Name and Password, not the PPP password. If
VersnLink is password protected and you are not an authorized user, you will not be able to change the values,
(VersaLink cannot be conﬁgured unless the user is logged in.) Contact your network administrator for further
instructions.
In" lnlemel mm
BeIISouth"
FostAccess°
Firewall and ,
W lnternetSerwce
Diagnostks
Enter Aﬂmlnlslrallnn Num-
Enter Admlnlstyetlnn Password
Verify Aﬂmlnlslrallnn Fasswnrﬂ
changes the system: adnu'rﬁxtratian password
nor the ppp password
any. a."
Change Password
Enter Administrative Name Type the name of your network administrative
NOTE: This changes the Systems Adminisnator
_password not the PPleassword.
Enter Administrative Password Type your network administrator’s password.
Verify Administrative Password lie-type your network administrator’s password.
030-300452 Revt A 139 May 2005
“Ell-300452 Rev. A
BullsnuthVers-Linkcl‘ewly
WEETEJ. ﬁll/05 - Dralt 2
User Guide VersaLink Gateway (Model 327W)
If you click an Firewall Log in the Firewall and Passwords Status page, the follawing page will be displayed.
This page alerts you of noteworthy information sent to your modem from the lntemet.
NOTE: One thousand entries can he made, but a maximum of 50 entIies are displayed at a time. Once 1000 entries
have been logged, the oldest entry is removed ta make space for new entries as they occur. The Firewall Lag menu
option will not be available if you are in Bridge Ethemet mode.
BelISouth°
’ Broadband " ' ' ' ' mmnm,‘ FustAccess”
Dsltinem M ., l \ “Team?“ lntemelService
Firewall Log
Packet The packet number.
Date The number of days passed since that the packet was sent,
Time The time that the packet ms sentl
DIreetinn/Souree The direction of transmission.
Rule/Reason The internal rule that caused the logged event. The intemal rule is set up under
Firewall rules.
Alert Displays a description of the logged event.
USO-300452 Rev. A 140 May 2005
030400452 M. A
BelISoutthlenkaway
WETELL 6/1/05 — Drift 2
User Guide VersaLx‘nk Galeway (Model 327 W)
13.51 Clear Log
If you click on Clear Log in the Firewall Log page, the following pop—up screen will be displayed. Click on OK to
clear the ﬁrewall log.
13.5.2 Printable/Savable Format
If you click on Printable/Savable Format in the Flrewall Log page, the following page will be displayed. This
option opens a new window that contains a list of all logged packets that can be saved or printed. After printing or
saving the log, click your browser’s “back" arrow to return to the Firewall Log page.
Firewall [my
new Null 15, m5
Time: l 2 "1:1!
030400452 Rev. A 141 May 2005
WTELI.
User Guide
13.5.3 Settings
030400452 Rev. A
BeIlSonthVeﬂaLlnkGateway
6/1/05 — Draft 2
VersaLink Gateway (Model 327W)
If you click on Settings in the Firewall Lng page, the following page will be displayed. This page allows you to
enable or disable the ﬁrewall log settings Click on save to save the settings.
log AllnmﬂTmlﬂl:
Ln! atom-1 mm:
Log mm: Spunlﬂnd n. Ruins
Lng Admlnlstrallva Amos:
Bel 1 South”
_ ~ FostAccess’
Internet Service
Firewall mesritilngs
Firewall Ln Settin s
Lug Allowed Trafﬁc
Factory Default = Disabled
This option allows the user to log the trafﬁc through the ﬁrewall that is
allowed via the ﬁrewall setup page.
Possible responses are:
Disabled
Inbound Packets
Outbound Packets
All Packets
Log Blocked Trafﬁc
Factory Default = Disabled
This option allows the user to log the trafﬁc through the ﬁrewall that is
being blocked via the ﬁrewall setup page.
Possible Response are:
Disabled
Inbound Packets
Outbound Packets
All Packets
Log Trafﬁc Speciﬁed in Rules
Factory Default = Enabled
When Enabled, this option allows the user to log the trafﬁc through the
ﬁrewall that is being allowed via the custom rules setup page.
If Disabled, this function will not be activated.
Log Adm istrative Access
Factory Default = Disabled
When Enabled, this option allows the user to log the times an
administrator has accessed any administrative protected modem pages
030—300452 Rev, A
142
May 2005
030400452 Rev. A
. BellSouthVerlelnkGllewly
WESTELL 611/05— Draft 2
User Guide Versalink Gateway (Model 327W)
If you click on Diagnostics at the main menu, the following page will be displayed This page enables you to
perform simple diagnostic tests on your modem. To conﬁgure the settings, click on the desired submenu button at
the right of the page.
NOTE: The Diagnostics menu option will not be available if you are in Bridge Ethernet mode. I
manna Mmmtnll mm mm.”
—_|
BellSouth’
»
Broadband " .' 5“ ',, yd A _ FasiAccess
Momma“ ‘ ‘ wit-eves; . 55mg, ‘ umgnostzs InternetService
v.“ ......... v we , we. -,
phglastaccvssxum
Diagnostics
run full diagnostics Enables you to run a full diagnostic test on the modem.
IP Tests
Portal Test will ping wwwfastaecessxom portal
Other Test will allow yowing a speeiﬁe URL or IP address of your choice
NS Lookup Default NS Lookup = www.yahoo.com
Test is a Name Server Lunkup.
Trace Route Test will deten-nine the route taken to destination for the URL of your choice, and will
show where the packet is stopped on the network.
Progress Window
Progress Window Displays the progress of the test beingperformed
030-300452 Rev. A 143 May 2005
030400452 Rev. A
BallSnthersnLinkGale’wny
WETEIJ. 6/1/05 - Dr!“ 2
User Guide Versalink Gateway (Model 327W)
If you want to run a ﬁll diagnostics test, click on run full diagnostics. The following page will be displayed. The
Diagnostics window will display . Testing in progress . unﬁl the diagnostics test has completed.
Inh-mz-I rxmm
BeIlSouth"
Home Emmi/and D, FustAccess
Wm?” “if“: ‘ "°""“( InternetSemce
magnumcs
nan-15,55“ res? '
...Test In pmgmss
ms Lnukup
Trans Rnula
Drngr swindnw
mm, in mm; u n: my...»
Hixzumlnhq m4 Mnnnanunw m mm...
030-300452 Rev. A 144 May 2005
039-300451 Reva A
BellSouthVeruLlnanteway
WnTEI—L 5/1/05 —Drait 2
User Guide VersaLink Gateway (Model 327W)
After the diagnostics test has cumpleted, the page will refresh and the test results will be displayed. If there is a
failure, the Diagnnstics ﬁeld will also display the details of the failed connection.
Q BellSouth‘
m aw "a m. ' , mm", _ FastAtcess
sfmm mm» "mm WM." mm“? , MW.“ IntemeiSen/ice
Ekhmll
winE
Mthnnlluullnn
m rm;
mm
mmr
m mun,
m;- num-
Diagnostics
Modem Self Test pass = Mudem passed self test
fail = Modem failed self test
DSL pass = DSL connection established
fail = No DSL connection established
ATM pass = ATM cells have been received over the PVC
fail = No ATM cells have been received over the PVC '
Ethernet pass = Ethernet frames have been received
fail = No Ethemet frames have been received
PPPoE pass = PADO has been received
fail = No PADO has been received
Authentication pass = Usemame/Password has been accepted
fail Usemame/Password has not been accepted
I? pass ing to wwwjastaccessccm was successful
fail = Ping to www.fﬂstaccess.c0m was not successful
IP Tests
Portal Test will ping www.fastaccess.com portal
Other Test will allow you to ping a speciﬁc URL or IP address of your choice
NS Lookup Default NS Lookup = www.yahoolcom
Test is a Name Sewer Lockup.
Trace Route Test will determine the route taken to destination for the URL of your choice, and will
show where the packet is stogped on the network.
Progress Window
Prggrcss Window Displays the progress of the test beingperfonned
030~300452 Rev. A 145 May 2005
was-rm
User Guide
“JD-300152 Rev. A
BelISouthersaLlnkGauway
6/1/05 — Draft 2
VersaLink Gateway (Model 327W)
To perform an IP test, click the test button that is adjacent to the test you wish to run,
ii
Maine
Summary
rmadb'and ‘
BeIISouth°
v ,. 1, - 'n» t, a FqstAccess“
Dsulne ‘ 7 ~. ‘ ; vfi’fffi InternetServlce
IP Tests
Portal Test Will Ring www.fastaccess.cam portal
Other Test will allow you to ping a speciﬁc URL or ll’ address of your choice
NS Lookup Default NS Lookup = www.yahoo.com
Trace Route
Test is a Name Server Lookupl
Test will determine the route taken to destination for the URL of your choice, and will
show where the packet is stopped on the network
Progress Window
Progress Window
Displays the progress of the test beingjerformed
030-300452 Rev. A
146 May 2005
030-300452 Rev. A
Bellsouﬂlversaunkcatewly
‘ 6/1/05 — Draft 2
WESTELL
User Guide
14.2.1 Portal Test
VersaLink Gateway (Model 327W)
The following page displays an example Portal test. The progress window will display the progress ofthe test. If
there is a failure, the Diagnostics ﬁeld will display the following message:
...Diagnostic Testing Complete...
Cannot access the speciﬁed URL or Web Address. Please try a different address by using the dialog box
marked Other and clicking the test button. If the problem persists, go to the Home Summary page and
restart the connection via connect/disconnect button in the Easy Logln page. Aﬂer the connection restarts,
return to the Diagnostics page and try the test again. If the problem persists, contact the BellSouth help
desk at l-888-321-2DSL (2375)
wireless
1 Diagnostic;
m. mu a.“
in Tests ,,
Partnl
other
we laukup
Tract: noun
‘ pmgress Wlnduw
Nfﬁxwanﬁi‘lsr’nﬁ'fﬁnn’nx...‘ '
t aning mm am" (a u...)
firewall and
Diagnasllcs
BeIISouth° '
FustAccessB
lnternet Service ‘
030-300452 Rev. A 147
May 2005
‘ 030400451 Rev. A
M BellSonthersaLinkGatewny
wssmu. 6/1/05 — Draft 2
User Guide VersaLin/c Gateway (Made! 327W)
14.2.2 Other
The following page displays an example Other test Note: lfthe Other field is blank when the test button is clicked,
the progress window will display a message that there is no IP address or URL to test.
If there is a failure, the progress window will display the following message:
.. .Dlagnostic Testing Complete...
Pinging (Ii> address or URL you entered) (3 times)
DNS Failure
Go to the Home Summary page and restart the connection via connect/disconnect button in the Easy Login page,
Aﬁer the connection restarts, return to the Diagnostics page and try the test again. If the problem persists, contact
the BellSouth help desk at 1—888-321-2DSL (2375).
‘ BelISouth°
Hm FustAccess
v summary. Internet Serwce
n: rests
Portal pinatamcmsenm
’ other Wynhonmm
, Ns Lnnkup
1 Trace Ruuts
Progress Window
1 ...i>miumc'mmce comm...
v, “MI-m; many-human u ulna)
ﬂute-ll
Sue-u
Queen:
030-300452 Rev. A 148 May 2005
030-300-152 new A
W EdISnuthVeranlnkGateway
wasrsu. 6/1/05 — Draft 1
User Guide VersaLin/c Gateway (Model 327W)
14.2.3 NS Lookup
The following page displays an example NS Lonkup test. Note: If the NS Lookup ﬁeld is blank when the test
button is clicked the progress window will display a message that there is no data, enter host name.
If there is a failure, the progress window will display the following message:
Diagnostic Testing Complete
NS Lookup Results: Host not found
Go to the Home Summary page and resmrt the connection via connect/disconnect button in the Easy Login page.
After the connection restarts, return to the Diagnostics page and try the test again. If the problem persists, contact
lhe BellSouth help desk at l-888-32l-2DSL (2375).
BeIlSouth"
FastAccess°
Internet Service
' mewunnna
Passwords
Home Broadband Home Magma“
i IFTests 7
‘ Faith
2 other
i Nsunkup
Trnn mum
ngress winﬂnw
.. mammal-ﬂ: usriﬁ'mﬁﬁ...
in mm Insult."
m.ms,m,un sum“
030-300452 Rev. A 149 May 2005
nan-300451 Rev. A
BellSoutthaLinkGateway
WETELL 6/1105 _ Draft 2
User Guide VersaLink Ga/eway (Model 327 W)
14.2.4 Trace Route
The following page displays an example Trace Route tesL Note: If the Trace Route ﬁeld is blank when the test
button is clicked or if there is a failure, the progress window will display only the following message:
Diagnostic Testing Complete
Go to the Home Summary page and restart the connection via connect/disconnect button in the Easy Logln page.
After the connection restarts, return to the Diagnostics page and try the test again If the problem persists, contact
the BellSouth help desk at 1-888-321-2DSL (2375).
BeIIScuth‘
FuslAccess°
Home ' minnow
‘ Summnv-VA ~, ,_ ,. ' , Passwords "l”g'wm“ , IntemetService
17 w Tests
5 Pnnnlh
‘ other
‘ NsLnnkup
030-300452 Revl A 150 May 2005
4/
WESTELL
User Guide
“SD-300451 Rev. A
BellSoanersaLinkalewly
6/1/05 — Draft 1
VersaLink Gateway (Model 327W)
Home
Summary
159 srnklsﬂcs
Broadband
0“ the MM“ Emmﬂrmd
Plug/rustic:
Luca Sn‘sdubgm v
«mam—ﬁns. ylmhgn/muulnmq
Next, select an option from the LOGS drop-down menu.
BelISouth”
FustAccess"
Internet Service
a «
x! F‘
‘ Lug sumac;
mm“; mfg” Diugnoslﬁcs
m, menu»; v
All 1.“
Cannauhn ~ -/
vam , ‘ ,, ,
BellSouth“
FustAccess“
Internet Service
030—300452 Rev, A
151
May 2005
030400452 Rev. A
BelISouthVersaLInaneway
WES'I'ELL 5/1/05 — Dr.“ 2
User Guide VersnLl'nk Gateway (Model 327W)
If you selecled All, the following page will be displayed. Click clear nu clear the log statistics, or click
printable/gamble format to print or save the logs ﬁle to a location on your PC.
BelISouth‘ ?
. “WM Fastlkcess' ,
~_.".".’f'ff.'A JET“; M lMﬁndxMce 5
mum. ”a. ' ' 1 j E ﬁ’
men rm j
1 All Entries :»
3 cumrmmsnm "
law. a m: sa m: 4? an
m. um mum “imb- mu
m. u... nus-m “A“, WM
Mm;
w- »... m“ n m. Sunk muaywmmx a“. ma
um w numwue rm mus 051. u. was. my“. u. m, aim-cw. w
mm m a...“ mam-um mnml. m'uu:
up.“ n m.- m... Wu» um m (raw-4x. m an»...-
m, 1. a... hummus-«inlvw-wulhr‘malum' g:
0,113: ll Mud-m unnam- nun-vim- mmwssm.(nm- mun mndwf) \
mm 1: lEsvmﬁD‘.‘ Ilaﬂwf: Sex-M ..
....... Mun! mm» m murmur
mum in m size-u
in snuznmvm mm» Sin-n
vunmmirnnnu- wwyahomnm
“sum.“ 1151 Eur: magm- ‘
7." mm , mm“
Mumszmvﬂ'liwu m.“
Hum-rumba: mun-2mm
ummqu. i... w m. S-eo-‘vv SNleNm litany-Mural
sfmrut|~w|m1mmimnry sun-mm Mammy...“
mum WW: msv (suns
Mums-inn! m. Du: pm Amm-
Emmi! pm m‘nm Am. pm in pix:
mam: u» mufﬁn) an m - m as ,|
unmzv (MEN 1 wax u, Cum-mm 4.- m m. nun-1
moms Mum 5m 1m n..-
mmm wr mum an vn - m 15: m (mum...
qmm» Mannheim mm): m, Can-mm a“. m n...“ Mans
u « mm mm m. m. m...“ gm m... m luv-awn]
m «Erma-mum. min-m smum mmumu
v>nzxrvrmnulnmcn m we. 3:
mm (amt-"w mm m an...“ m. m av w
mum LEAH-u 3.5 15mm: 1:
mm us Marga. l n n: um: in
mm us n in.“ mm u Fuw- m
n.n.n.2n us an m: m mum: in nu um m mum
up in w-an m on u w
up n m Wu. mmwzm
m n m... min mmmm ‘
u M mom: v-uu: new
a n n n “mm" mmw mm
rm annw
m .: «mm be a.
030-300452 Ravi A 152 May 2005 ‘
‘ 030400452 rm. A
BelISonthVersnLinanteway
' 6/1/05 -Dral'tl
WETELL
User Guide VerraLink Gateway (Made! 327W)
For your convenience, the Weslell VersaLink Gateway supports protocols for Applications, Games, and VPN—
speciﬁc programs. Table 5 provides protocol information for the services that are supported by your VersaLink
Gateway.
Note: To conﬁgure VersaLink for a service or ﬂppl on, follow the steps described in section 11.3
(NAT/Gaming) oflhis User G
Table 5. Applications/Games/NAT VPN Support
Navigation/Game | Port/Protocol
Aliens vs. Predator 80 UDP, 2300 UDP, 8000-8999 UDP
Age of Empires II: The 6073 UDP, 47624 TCP, 2300-2400 TCP/UDP
Cmuerors This service will Open up_port’s for both trafﬁc directions
Americas Army TCP — 20045
UDP - 1716 to 1718 8777, 27900
America Online 5190 TCP/UDP
AnarchLinine TCP/UDP — 70127013, 7500 -7505
AOL Instant Messenger 4099 TCP, 5190 TCP
Asheron's Call 9000-9013 UDP, 28800-29000 TCP
Batﬂecom 23004400 TCP/UDP, 47624 TCP/UDP
Battleﬁeld 1942 UDP - 14567 22000, 23000 to 23009, 27900, 28900
Black and White 2611~Z612 TCP, 6667 TCP, 6500 UDP, 27900 UDP
Blizzard Battlemet (Diablo II) 4000 TCP 6112 TCP/UDP
Buddy Phone 700, 701 UDP
Bungienet, Myth, Myth 11 3453 TCP
Server
Cnlista IP Phone 3000 UDP 5190 TCP
Citrix Metaframe 1494 TCP
Client POP/IMAP 110 TCP
Client SMTP 25 TCP
Counter Strike 27015 TCP/UDP, 27016 TCP/UDP
Dark Reign 2 26214 TCP/UDP
Delta Force ( Client and 3568 UDP, 3100-3999 TCP/UDP
Server )
Delta Force 2 3568-3569 UDP
DeltaFurce: Land Warrior UDP 53
TCP 21
TCP 7430
TCP 80
UDP 1029
UDP 1144
UDP 6543 6
UDP 17478
DNS 53 UDP
Elite Force 2600 UDP 27500 UDP, 27910 UDP, 27960 UDP
Everquest 1024-7000 TCP/UDP
F-16_,_Mig 29 3863 UDP
F-22 Lightning 3 4660-4670 TCP/UDP 3875 UDP, 45334534 UDP, 4660-4670 UDP
F-22 Raptor 3874-3875 UDP
030400452 Rev. A 153 May 2005
030400452 Rev. A
BellSonﬂlVersaLinszreway
wss'rm 5/1/05 - mm 1
User Guide VersaLink Gateway (Model 327W)
Application/Game Port/Protocol
Fighter Ace 1'I 50000-50100 TCP/UDP
Fight_er Ace II for DX play 50000-50100 TCP/UDP, 47624 TCP, 2300-2400 TCP/UDP
FTP 20 TCP, 21 TCP
GameSpy Online UDP 3783
UDP 6515
TCP 6667
UDP 12203
TCP/UDP 13139UDP 27900
UDP 28900
UDP 29900
UDP 29901
Ghost Recon TCP 80
UDP 1038
UDP 1032
UDP 53
UDP 2347
UDP 2346
GNUtella 6346 TCP/UDP 1214 TCP
HalfLife Server 27005 UDP(client only)
270 1 5 UDP
Heretic 11 Server 28910 TCP
Hexen II 26900 (+1) each player needs their own porL Increment by one for
each person
Holline Server 5500, 5503 TCP 5499 UDP
HTTPS 443 TCP/UDP
ICIW’ Echo 4 [CW
|_ ICQ OLD 4000 UDP, 20000-20019 TCP
ICQ ZOOII: 4099 TCP 5190 TCP
ICUII Client 2000-2038 TCP, 2050-2051 TCP, 2069 TCP, 2085 TCP, 3010-3030
TCP
ICUII Client Version 4.xx 1024-5000 TCP, 20502051 TCP, 2069 TCP, 2085 TCP, 3010-3030
TCP, 20004038 TCP6700-6702 TCP, 6880 TCP, 1200-16090 TCP
MAP 1 19 TCP/UDP
IMAP v.3 220 TCP/UDP
Internet Phone 22555 UDP
IPSEC ALG ENABLES ALG
IPSEC ESP PROTOCOL 50
IPSEC IKE 500 UDP
[visit 9943 UDP, 56768 UDP
JKIIJO (Jedi Knight II: Jedi UDP - 28070 (default)
OutCast UDP- 27000 to 29000
KALI, Doom & Doom 1!
2213 UDP, 6666 UDP (EACH PC USING KALI MUST USE A
DIFFERENT PORT NUMBER STARTING WITH 2213 + 1
KﬂZaA 1214 TCP/UDP
Limewire 6346 TCP/UDP, 1214 TCP
Medal Of Honor: Allied TCP 80
Assault UDP 53
UDP 2093
UDP l 220 l
TCP I2300
UDP 2135
UDP 2139
030-300452 Rev. A 154 May 2005
030400552 Rev. A
BellSnnthVersnLinkG-leway
was‘re 6/1/05 — Bu" 2
User Guide VersaLink Gateway (Model 327W)
A 1' alien/Game Port/Protocol
TCP/UDP 28900
mlRC Chat 6660-6669 TCP
Motorhead Server 16000 TCP/UDP, 16010716030 TCP/UDP
MSN Game Zone 6667 TCP, 28800-29000 TCP
MSN Game Zone (DX 7 & 8 6667 TCP, 6073 TCP, 28800-29000 TCP, 47624 TCP, 2300-2400
play) TCP/UDP
This service will open ugpon’s for both trafﬁc directions.
MSN Messenger
6891-6900 TCP, 1863 TCP/UDP, 5190 UDP, 6901 TCP/UDP
Napster 6699 TCP
Need for Speed 3, Hot Pursuit 1030 TCP
Need for Speed, Porsche 9442 UDP
Net2l’hone 6801 UDP
NNTP 119 TCP/UDP
Operation FlashPoint 47624 UDP, 6073 UDP, 2300-2400 TCP/UDP, 2234 TCP
Outlaws 5310 TCP/UDP
Pal Talk 2090-2091 TCP/UDP, 2095 TCP, 5001 TCP, 8200-8700 TCP/UDP,
10254500 UDP
EcAnmhere host
5631 TCP 5632 UDP, 22 UDP
Phone Free 1034-1035 TCP/UDP, 9900-9901 UDP, 2644 TCP, 8000 TCP
Quake 2 27910 UDP
Quake 3 27660 UDP
Each computer playing QuakeHI must use a different port number,
starting at 27660 and incrementing by 11 You'll also need to do the
following:
1. Right click on the 0111 icon
2. Choose “Properties"
3‘ In the Target ﬁeld you'll see a line like "C;\Program F iles\Quake 111
Arena\quake3.exe"
4. Add the Quake III net_port command to specify a unique
communication port for each system. The complete ﬁeld should look
like this: "C:\Program Files\Quake III A:ena\quake3.exe" ﬂet
net _port 27660
5. Click OK
6. Repeat for each system behind the NAT, adding one to the net_port
selected (27660‘27661 27662)
Quicktime 4/Real Audio
6970-32000 UDP, 554 TCP/UDP
Rainbow Six & Rogue Sgear
RealOne Player
2346 TCP
TCP - 554, 7070 to 7071
UDP - 6970 to 7170
Real Audio
6970-7170 UDP
Retum To Castle Wolfenstein
Default -27960 TCP/UDP
UDP - 27950 to 27980
Roger Wilco TCP/UDP 3782
UDP 3783 (BaseStution)
ShoutCast Server 8000-8005 TCP
Spinner Radio/Netscape TCP - 554
Music
SSH Secure Shell 22 TCP/UDP
Starcraﬂ 2346 TCP
Starﬂeet Command 2300-2400 TCP/UDP, 47624 TCP/UDP
SOF/SOFH (Soldier of
Fortune / Soldier of Fortune
UDP ~ 28910 to 28915
030400452 Rev. A
155 May 2005
030-300-152 Rev‘ A
BellsnuthverleinkGatewny
6/ll05 — Draft 2
WE‘I’ELI.
User Guide VersaLin/c Gateway (Model 32 7 W)
Application/Game Part/Protocol
I1)
Telnet 23 TCP
LTiberian Sun & Dune 2000 1 140-1234, 4000 TCP/UDP
TribesZ TCP - 15104, 15204, 15206, 6660 to 6599
UDP - 27999 to 28002
Ultima Online 5001-5010 TCP, 7775-7777 TCP, 8800-8900 TCP, 9999 UDP, 7875
UDP
Unreal Toumament sewer 7777 (default gameplay port)
7778 (server query port
7779,7779+ are allocated dynamically for each helper UdpLink
objects, including UdpServerUplin objects. Try starting with 7779-
7781 and add
ports if needed
27900 server query, if master server uplink is enabled. Home master
sewers use other ports like 27500
Port. 8080 is for UT Server Admin. In the [UWeb.WebServer] section
of the serverjni ﬁle, set the ListenPort to 8080 and ServerName to the
IP assigned to the router from your ISP.
USENET News Service 143 TCP
VNC, Virtual Network 5500 TCP, 5800 TCP, 5900 TCP
Computing
Westwood Online, C&C 4000 TCP/UDP 114041234 TCP/UDP
World Wide Web (HTTP) 80 TCP
443 TCP (SSL)
8008 OR 8080 TCP QPROXX!
Yahoo Messenger Chat 5000-5001 TCP
Yahoo Messenger Phone 5055 UDP
IPSec Encryption IPSec using AH can not be supported through NAT. lPSec using ESP
and L2TP can he sugported via an ALG
LZTP IPSec using ESP and L2’I‘P can be summed via an ALG.
PPTP Works through NAT.
030-300452 Rev. A 156 May 2005
inn-300452 Rem A
BellsnuthztsnLinkGateway
-TELL 6/1/05 — Draft 2
User Guide VersaLink Gateway (Model 327140
Refer to this section for a detailed explanation on connection failures.
If you entered your login values (provided by BellSouth) at the Customer Information page and your login failed,
the following page will appear. Click next to return to the Customer Information page and re-enter your login
values. If this problem persists, contact the BellSouth help desk at l-885-32142DSL (2375).
Lngln Fl! Cllck next is rI-urtI-r your ens-mar Intel-mallar-
and m mm...
u this pmhlsm vsmlsls, plvnsn mum
on hllp am a! i-ees»asz»zusi. (2875)
The following pop—up screen will be displayed if the value in your Conﬁrm Password ﬁeld is not identical to the
value in your Password ﬁeld. The Password and Conﬁrm Password ﬁelds must contain identical values in order
to establish a successful login. If you have retyped the appropriate values in each ﬁeld and are still unable to
establish a connection, contact the BellSouth help desk at l-SBS-BZl-ZDSL (2375).
030-300452 Rev. A 157 May 2005
’ nan-300452 Rev. A
BellsouthveriaLlnkGatewny
WESTEJ. 611/05 — Bra]! 2
User Guide VersaLink Gateway (Model 327W)
If you entered your login values (provided by BellSouth) at the Easy Login page and your login failed, the
following page will appear. Retype the appropriate values in the User 11) and Password ﬁelds and click on connect.
If this problem persists, contact the BellSouth help desk at 1-888-321-2DSL (2375),
x —Mlcmmll lnlcmr-l Explavm
BelISouth"
' jﬁmtrm‘ '_ ~ _ FustAccess
”mm ‘v A“ ‘ ”LA ijgmmsv lntemetService
‘ Eavaa m
Logln railedfpleasve'h‘eck yoEFTJserTu and password and try again.
if mi; problem persists, please Contact the help desk at
l-888-321-2DSL (2375).
usnr m mmEﬁaQseu-umnm
Exsnwls; usemamooeusmmmr
Password -—-
Nov/den by your (SP.
comm. ausswnrd
The following pop-up screen will be displayed if the value in your Conﬁrm Password ﬁeld is not identical to the
value in your Password ﬁeld. The Password and Conﬁrm Password ﬁelds must cuntain identical values in order
to establish a successful login. If you have retyped the appropriate values in each ﬁeld and are still unable to
establish a connection, contact the BellSouth help desk at 1-888-321-2DSL (2375).
030-300452 Revr A 158 May 2005
0304500451 Rev. A
BeIISnlltllVQrsaLinkGatevl/ay
WIITELL GIVES-Drum!
User Guide VersaLink Gateway (Model 3271”
o; nection
If your DSL connection is down when you log into the Customer Information page, the following page will
appear.
- Check that the phone line is securely connected to your FastAccess modem.
- Clleok that the DSL LED on the front of your FastAccess modem is solid green and is not blinking.
- Check that ﬁlters have been installed on all phone jacks that have telephone devices connected to them.
If this problem persists, contact the BellSouth help desk at l-888—321-2DSL (2375).
esl. cannunlnn nu! nan us. chuckma hllnwlng:
. DSL cum-mun ls securely pluggld Inn-l ynnr m: Amss
mular.
. DSL Light on thl Iron! 0? your Fast Amess router IS sulld Quinn
and no! blinking grlln,
. Fillers hu‘ll bun Innelled on all 9mm! jacks that have
(Cl'phnn- duvlces annealed“: them.
mllls problem p-rslsts, plugs mum-t the help desk at 1-
naa—azl—znst (2375)
030-300452 Rev. A 159 May 2005
(DD-300452 Kai. A
BdlSouthenaLlnkGatewzy
WETELL 6/1/05 — Draft 1
User Guide VersaLink Gateway (Made! 327W)
Once a DSL connection is detected, please wait a brief moment while the modem connects to the ISP’s equipment.
After the modem has connected, the DSL LED will light solid green and the DSL sync will be Up.
hummus, canal-ulna
Mu m: mm nun-ﬂ...
Close all browser windows, and then re-open your browser to launch your BellScuth® FastAccess® DSL
connection.
um ALL luvwxlr nhdnwx.
Rrunln vuur nmwsmn lunch vnurnllnmn" amm-
m mum-m.
When you are ready to access the modem’s web pages, type httpzlllaunchmodem in the browser’s address bar and
press “Enter" an your keyboard. The Home Summary page will be displayed.
030-300452 Rev. A 160 May 2005
030000452 Rev. A
M BellSnnthVnsaLinkGaleway
WEE‘I’ELI. 6/1/05 — Bull 2
User Guide Versalink Gateway (Model 327W)
If the ATM connection is down when you log into the Customer Information page, the following page will appear.
Contact the BallSouth help desk at 1-888-321-ZDSL (2375).
BellSouth"
¢
H B m d. . I” A, d ‘ _ FustAccess
5”:er fggl We" Wireless Amafg Dmgnosbts ‘ m r net Set vice
“Mum...“ _ w pumwmwd' nww-‘ w, u,
1 Easy Login
4 ATM connection is down. Please contact the help desk at 1-
5 888-321-2DSL (2375).
User ID 5519"
Example: usemameobelfsouthmet
Passwnrd z 7 ,,
Provided by your ISP.
030-300452 Rev. A 161 May 2005
' 030600452 Rev. A
BellsonlhversaLinanuwny
wean-El... Slims—Draft 1
User Guide VersaLink Gateway (Made! 327W)
If you cannot connect w your target Internet service provider, the following page will appear. Contact the BellSouth
help desk at 1-888-321-2DSL (2375)
NOTE: If you attempt to connect to the Internet and your connection fails, the Internet LED will light red and then
rerum tn the OH states
BelISouth“
FaslAccess’
lnternet Service
Lenin
Cmmnl cnnnecl w nurgetscrvue, Please contact the help desk at
1'688'321-2DSL (2375),
user") F—usemmwmpm
Example: “anemone/Immamt
wasswnm ~—~
Prow'dedby your rsw.
ennunn Pas§wnrﬂ ---
Once your connection succeeds, the Internet LED will light solid green, and at the Home Summary page the
Internet Login ﬁeld will display Up.
(BO-300452 Revs A 162 May 2005
“JO-300452 Rev. A
BellSuuthVernLiukatewly
WESTELL 6/1/05— mm 2
User Guide VersaLin/c Gateway (Mariel 327W
This section explains the conﬁguration details for VersaLink’s WAN PORT feature. To access this feature, click
Broadband DSL Line as the main menu, and then click the WAN button. The following page will be displayed. At
the WAN PORT drop-down menu, select either DSLATM PORT or ETHERNET PORT 1 for your WAN setting.
NOTE: If you use VersaLink’s DSLATM PORT mode, you will enable VersaLink’s DSL transceiver. This will
disable the WAN Ethernet interface (labeled Ethernet 1) on the rear panel ofVersaLink and allow the WAN
interface to use the DSL port instead. Conversely, if you use VersaLink’s uplink mode, ETHERNET PORT 1, you
will disable VersaLink’s DSL transceiver. This will disable the DSL port (on the rear panel of VersaLink) and allow
the WAN interface to use the Ethernet 1 port.
BellSouth"
' m 4 ' 5mm \ FustAccess
_,5."ffl'_',"’,”~ ., N, ». t t ”WW“ p 4 lntemetSerwce
wmcmungnmqan ,, 7
WAN Pom DSLATMPORT 3
Status VPI VCI Protocol
Enable V 35 PPPDE
Dlteble L as armge
sv Brlt‘lga
ea Brldg-
as Brldge
Disable v m Brltigu
Dlsulzle 1 ﬂ Brit!!!
srtdgu Brendan
Brldge Mulllcast
spannlng Tree Promenl
030-300452 Rev. A 163 May 2005
030400452 Rev. A
, BeuSnuthVeruLiukG-“eway
6/1/05 — Draft 1
WEETELI.
User Guide VersaLink Gateway (Model 327W)
IfVersaLink is in DSLATM PORT mode and you want to conﬁgure VersaLink for ETHERNET PORT 1 mode,
follow the instructions provided in this section. By using the ETHERNET PORT 1, you will disable VersaLink‘s
DSL transceiver. This will disable the DSL Port and allow the WAN interface to use the WAN Ethernet Port
(Ethernet 1) on the rear of the modem.
NOTE: The uplink feature (Ethernet 1) is optional, If ETHERNET PORT l is disabled, VersaLink will use DSL
and Wireless only, and the Ethernet 1 port can be used in addition to ports E2, E3, and E4 for LAN access. When
using DSLATM PORT, you may connect to any of the three Ethernet (E2, E3, or E4) jacks on the rear panel of
VerraLink as they serve as an Ethernet switch. Ethernet 1 port is used as a WAN transport connection when
installing VersaLink without DSL. When using Ethernet 1 port instead of the DSL port, Ethemet LAN connection is
limited to ports E2, E3, and E4. The uplink feature (ETHERNET PORT l) is optional, and if it is not enabled in the
.ini ﬁle, VersaLink will use DSL and Wireless only.
To use ETHERNET PORT 1, click the WAN button in the Broadband DSL Line page, the following page will
be displayed. Next, select ETHERNET PORT 1 from the WAN PORT drop-down menu.
e!
BeIlSouth”
femur"; ,_ . FastAccess“
‘ms’m’d‘ ”WWW“ InternetService
.... E; “as“. _.4
WANPORT DSLA‘I'MPORT :-
DSLATM PORT
VP rotncnl
as PPFuE
as Bridge
s7 Bridge
as Bridgl
as Bridge
40 Bridg-
41 arldg-
deg- Broadcast
Bridge Multlelsl
spanning mm Prulnnnl
NOTE: If you experience any problems, please reset VersaLink via the external hardware reset button or via the
procedure deﬁned in the Reset Modem menu in section 9.5 (Reset Modem). The actual information displayed in
this page may vary, depending on network connection established.
030-300452 Rev. A 164 May 2005
Mil-300452 Rev. A
M Bel|SuutherslunkGarewny
WEETELI. 6/1/05 — Drill 2
User Guide VersaLin/t Gateway (Model 327119
If you selected ETHERNET PORT 1 ﬁom the WAN PORT drop-down menu, the following screen will be
displayed. Click OK.
If you clicked on OK in the preceding pop-up screen, the following screen will be displayed. Click on OK If you
click on Cancel, the change will not take effect.
mm , IllntemelEx Inrer Bi
If you clicked on OK in the preceding pup-up screen, the following pop-up screen will appear. VersaLink must be
reset to allow the new aonﬁgrration to take effect. Click on OK.
If you clicked on OK in the preceding screen, the following screen will be displayed. VersaLink will be reset and
the new conﬁguration will take effect. Aﬁer a brief delay, the Home Summary page will be displayed.
NOTE: After VersaLink has been reset, the DSL LED will be OFF. This is because the DSL transceiver has now
been disabled. However, the Power, Ethernet, Wireless and Internet LEDs will remain lit.
> warning
“Jun- n u y...“ M»,
[BO-300452 Rev. A 165 May 2005
' can-300452 Rev, A
Bensuutnwrsxunkcmmy
sit/05 - Bra“ 2
User Guide VersaLink Gateway (Model 327 W)
If VersaLink is in ETHERNET PORT 1 mode and you want to conﬁgure VersaLink for DSLATM PORT mode,
follow the instructions provided in this section. By using the DSLATM PORT, you will enable VersaLink’s DSL
transceiver. This will disable the WAN Ethernet port and allow the WAN interface to use the DSL port on the rear
of the modem. To enable the DSLATM PORT, click on Broadband DSL Line at the main menu, and then click
the WAN button.
NOTE: The uplink feature (Ethemet l) is optional. IfETlERNET PORT 1 is disabled, VersaLink will use DSL
and Wireless only, and the Ethernet 1 port can he used in addition to ports 132, ES, and E4 for LAN access. When
using DSLATM port, you may connect to any of the three Ethernet (E2, ES, or E4) jacks on the rear panel of
VersaLink as they serve as an Ethernet switch. Ethernet l port is used as a WAN transport connection when
installing VersaLink without DSL. When using Ethemet 1 port instead of the DSL port, Ethernet LAN connection is
limited to ports E2, E3, and EA. The uplink feature (ETHERNET PORT l) is optional, and if it is not enabled in the
.ini ﬁle, VersaLink will use DSL and Wireless only.
To use DSLATM PORT, click the WAN button in the Broadband DSL Line page, the following page will be
displayed.
—_‘I
BeIISouth°
FostAccess’
wrrevess ﬁﬁ’éﬁaﬁ” mm“ Internet Service
WAN pom ETHERM-TFPGHH v~
Protocol
NOTE: If you experience any problems, please reset VersaLink via the external hardware reset button or via the
procedure defmed in the Reset Modem menu in section 9.5 (Reset Modem). The actual information displayed in
this page may vary, depending on network connection established.
030-300452 Rev. A 166 May 2005
nan-300452 Rev. A
_ BeHSonthVersaLinkaway
WEETEL 6/1/05 — Draft 2
User Guide VersaLink Gateway (Model 327170
Next, select DSLATM PORT from the WAN PORT drop-down menu.
BeH‘South“>
‘ , FustAccess“
figmi“ , mtemet Service
Brvadband
DSL Lille
Status
Enabled
030-300452 Rev. A 167 May 2005
nan-anus: Rev. A
BdlSouthVersaLinaneway
wm'rsu. 6/1105 - Draft 2
User Guide VersaLink Gateway (Model 32 7149
If you clicked OK, the following pop-up screen will be displayed. VersaLink must now be reset to allow the new
conﬁguration to take effect. Click on OK.
M msuil lnlemel
Aﬂier you click OK in the preceding screen, the following screen will be displayed and the modem will be reset.
Aﬂer a brief delay, the Hume Summary page will be displayed. Conﬁrm that the DSL and Internet Login ﬁelds
display Up. (Depending on your connection type, you may need to go to the Easy Login page and click the connect
button to establish a PPP session. After you establish a PPP session, the Internet Login ﬁeld should display Up.)
> warning
; m mm m
mm mm
Vamp-g. it! a. mum xhww.
030-300452 Rev. A 168 May 2005
WEE‘TELL
User Guide
DSL Line Code: Discrete Multi-Tone (DMT)
DSL Rates: 32 kbps to 8 Mbps downstream
and 32 kbps to 800 Kbps upstream
Power spectral density: -40 dBm/Hz
DSL Impedance: 100 Ohms
DSL Performance: Performance: per
G.992.l, ANSI T1413.
Protocol Features
Bridge Encapsulation per RF02684
(Formerly RFC1483)
Logical Link Control/ Subnetwork Access
Protocol (LLC/SNAP)
Software Upgradeable
PPPoE Support
ATM SAR: Internal to Modem
System Requirements for 10/100 Base-T/Ethernet
Pentium Class PC or above, Macintosh
Microsoft Windows (98 SE, 2000, ME, NT
4.0, or XP), Linux, or MAC OS X installed
Operating system CD
Internet Explorer 4.x or Netscape Navigator
4.x or higher
64 MB RAM (128 MB recommended)
Ethernet 10/100 Base-T interface
10 MB of free hard drive space
TCPIIP Protocol Stack installed
10/100 Base»T Network Interface Card (NIC)
System Requirements for Wireless
Pentium® or equivalent and above class
machines
Microsoft® Windows® (98 ME, 2000, or
XP) or Macintosh® OS X installed
Operating System CD on hand
Internet Explorer 4.x or Netscape Navigator
4.x or higher
64 MB RAM (128 MB recommended)
10 MB of free hard drive space
IEEE 802.1 lb/g/g+ PC adapter
030400452 Rev. A
BellSouthVerleinkGateway
6/1/05 — Draft 2
VersaLink Gateway (Model 327W)
- Power
- E1, E2, E3, E4
. Wireless
- DSL
- Internet
Connectors
0 DSL/LINE: 6-pin modularjack RM 1
- Ethemet: 8-piu RJ-45 modularjack
- Power connector: 12V DC
- Wireless IEEE 802.11b/g SMA connector
and antenna
Environmental
0 Ambient Operating Temperature: +32 to
+104°F (0 to 140°C)
- Relative Humidity: 5 to 95%, non-
condensing
Power Supply/Consumption
o 120 VAC to 12V DC wall-mount power
supply
- Less than 4 watts typical, from 120 VAC
Environmental
0 Ambient Operating Temperature: +32 to
+104°F (0 to +40°C)
. Relative Humidity: 5 to 95%, non-
condensing
EMCISafety/Regulatory Certiﬁcations
0 BMC: FCC Part 15, Class B
UL Standard 60950, 3” Edition
CAN/GSA Standard C221 No. 60950
UL
CSA
ACTA 968-A
Industry Canada C503
cocoon
030-300452 Rev. A
169
May 2005
/ “JD-300452 Rev. A
BeHSouthVerraLInkGateway
WMLL 6/1/05 — Draft 2
User Guide VersaLink Gateway (Model 327 W)
as“
READ TEE TERMS AND CONDITIONS OF THIS LICENSE AGREEMENT CAREFULLY. THIS
SOFTWARE IS COPYRIGHTED AND LICENSED (NOT SOLD). BY INSTALLING AND OPERATING
TmS PRODUCT, YOU ARE ACCEPTING AND AGREEING TO THE TERMS OF THIS LICENSE
AGREEMENT. IF YOU ARE NOT WILLING TO BE BOUND BY THE TERMS OF THIS LICENSE
AGREEMENT, YOU SHOULD PROMPTLY RETURN THE SOFTWARE AND HARDWARE T0
WESTELL TECHNOLOGIES, INC. THIS LICENSE AGREEMENT REPRESENTS THE ENTIRE
AGREEMENT CONCERNING THE SOFTWARE BETWEEN YOU AND WESTELL TECHNOLOGIES,
INC. (REFERRED TO AS "LICENSOR"), AND IT SUPERSEDES ANY PRIOR PROPOSAL,
REPRESENTATION, OR UNDERSTANDING BETWEEN THE PARTIES.
1. License Grant. Licensor hereby grants to you, and you accept, a nonexclusive license to use the
SOFTWARE Compact Disk (CD) and the computer programs contained therein in machine-readable, object
code form only (collectively referred to as the "SOFTWARE"), and the accompanying User Documentation,
only as authorized in this License Agreement. The SOFTWARE may be used only in connection with the
number of systems for which you have paid license fees as dictated in your support agreement. You agree
that you will not assign, suhlicense, transfer, pledge, lease, rent, or share your rights under this License
Agreement. You agree that you may not nor allow others to reverse assemble, reverse compile, or otherwise
translate the SOFTWARE.
You may retain the SOFTWARE CD for backup purposes only, In addition, you may make one copy of the
SOFTWARE in any storage medium for backup purposes only. You may make one copy of the User's
Manual for backup purposes only. Any such copies of the SOFTWARE or the User's Manual shall include
Licensor's copyright and other proprietary notices. Except as authorized under this paragraph, no topics of
the SOFTWARE CD or any portions thereof may he made by you or any person under your authority or
control.
2. Licensor's Rights. You acknowledge and agree that the SOFTWARE and the User's Manual are
proprietary products of Licensor protected under U.S. copyright law. You further acknowledge and agree
that all right, title, and interest in and to the SOFTWARE, including associated intellectual property
rights, are and shall remain with Licensor. This License Agreement does not convey to you an interest in or to
the SOFTWARE, but only a limited right of use revocable in accordance with the
terms of this License Agreement.
3. License Fees. The fees paid by you under the support agreement are paid in consideration of the licenses
granted under this License Agreement.
4. Term. This License Agreement is effective upon your opening of this package and shall continue until
terminated. You may terminate this License Agreement at any time by returning the SOFTWARE CD and
all copies thereof and extracts there from to Licensor. Licensor may terminate this License Agreement upon
the breach by you of any term hereof. Upon such termination by Licensor, you agree to return to Licensor
the SOFTWARE CD and all copies and portions thereof.
5. Limited Warranty. Licensor warrants, for your beneﬁt alone, for a period of 90 days from the date of
commencement of this License Agreement (referred to as the "Warranty Period") that the SOFTWARE CD
in which the SOFTWARE is contained are free from defects in material and workmanship. Licensor further
warrants, for your beneﬁt alone, that during the Warranty Period the SOFTWARE shall operate
substantially in accordance with the functional speciﬁcations in the User's Manual. If during the Warranty
Period, a defect in the SOFTWARE CD appears, you may return the SOFTWARE CD to Licensor for
replacement. You agree that the foregoing constitutes your sole and exclusive remedy for breach by Licensor
of any warranties made under this Agreement.
030-300452 Rev. A 170 June 2005
' USU-300452 Rev. A
BeIlSouthVersaLlnkGateway
WETELI. 6/1/05 — Bra“ 2
User Guide VersaLink Gateway Model 327m
EXCEPT FOR THE WARRANTIES SET FORTH ABOVE, THE SOFTWARE C1),
AND THE SOFTWARE CONTAINED THEREIN, ARE LICENSED "AS IS," AND
LICENSOR DISCLAIMS ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESS
OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
6. Limitation of Liability. Licensor‘s cumulative liability to you or any other party for any loss or damages
resulting from any claims, demands, or actions arising out of or relating to this Agreement shall not exceed
the license fee paid to Licensor for the use of the SOFTWARE. In no event shall Llcensor be liable for any
indirect, incidental, consequential, special, or exemplary damages or lost proﬁts, even if Liceusor has been
advised of the possibility of such damages. SOME STATES DO NOT ALLOW THE LINHTATION OR
EXCLUSION OF LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
7. Governing Law. This License Agreement shall be construed and governed in accordance with the laws of
the State of Illinois. You submit to the jurisdiction of the state and federal courts of the state of Illinois and
agree that venue is proper in those courts with regard to any litigation arising under this Agreement.
8. Costs of Litigation. If any action is brought by either party to this License Agreement against the other
party regarding the subject matter hereof, the prevailing party shall be entitled to recover, in addition to any
other relief granted, reasonable attorney fees and expenses of litigation.
9. Severabllity. Should any term of this License Agreement be declared void or unenforceable by any court of
competent jurisdiction, such declaration shall have no effect on the remaining terms hereof.
10. No Waiver. The failure or either party to enforce any rights granted hereunder or to take action against
the other party in the event of any breach hereunder shall not be deemed a waiver by that party as to
subsequent enforcement of rights or subsequent actions in the event of future breaches.
GEO-300452 Rev. A 171 June 2005
' tun-300452 Rev. A
‘ BellSonthersaLlnkGahewny
WESTE ﬁll/us - Dull 2
User Guide VersaLink Gateway (Model 32 7m
We50e11® Versa LinkTM Gateway (Model 327W)
User Guide Part no. 030-300452 Rev. A
Copyright © 2005 Weslell, Inc.
All rights reserved.
Westell, Inc.
750 North Commons Drive
Aurura, Illinois 60504 USA
wwwlwestellﬁom
All mademarks and regismered trademaxks are the property of their respective owners.
inlnln
a n
inrlwanx
030-300452 Reve A 172 June 2005

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 90
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:91e354fb-bbbd-499b-9464-ef63f24328e7
Modify Date                     : 2005:06:21 14:24:56-07:00
Create Date                     : 2005:06:21 14:24:44-07:00
Metadata Date                   : 2005:06:21 14:24:56-07:00
Document ID                     : uuid:9b409852-69dc-4a9e-a3d7-576822f256bd
Format                          : application/pdf
Title                           : 
Creator                         : Canon
Author                          : 
Subject                         : Image
Producer                        :

EXIF Metadata provided by EXIF.tools

Westell C90327WXX-06 4 Port wireless gateway router User Manual Part II

Westell Inc 4 Port wireless gateway router Users Manual Part II

Contents

Users Manual Part II

FCC ID Filing: CH8C90327WXX-06

Navigation menu

Namespaces

Views

Navigation