Whirlpool GEW9200LQ0 User Manual DRYER Manuals And Guides L0409510

WHIRLPOOL Residential Dryer Manual L0409510 WHIRLPOOL Residential Dryer Owner's Manual, WHIRLPOOL Residential Dryer installation guides

User Manual: Whirlpool GEW9200LQ0 GEW9200LQ0 WHIRLPOOL DRYER - Manuals and Guides View the owners manual for your WHIRLPOOL DRYER #GEW9200LQ0. Home:Laundry & Garment Care Parts:Whirlpool Parts:Whirlpool DRYER Manual

Open the PDF directly: View PDF .
Page Count: 28

ELECTRONIC

ELECTRICDRYER

_iii_!iii_!!_,_ii_,:;:i::iili!io_i%__ii::¸il,ii_i_i_i::_,_:!_,

For questions about features, operation/performance, parts accessories

or service call: 1-800-253-1301

or visit our website at... www.whirlpool.com

Table of Contents ................................................ 2

3979274B

TABLEOFCONTENTS

DRYER SAFETY .............................................................................. 3

INSTALLATION INSTRUCTIONS .................................................. 4

Tools and Parts ............................................................................ 4

Optional Pedestal ......................................................................... 4

Location Requirements ............................................................... 5

Electrical Requirements ............................................................... 7

Electrical Connection ................................................................... 8

Venting Requirements ................................................................ 12

Plan Vent System ....................................................................... 12

Install Vent System ..................................................................... 14

Install Leveling Legs ................................................................... 14

Level Dryer ................................................................................. 14

Connect Vent .............................................................................. 15

Reverse Door Swing .................................................................. 15

Complete Installation ................................................................. 17

DRYER USE .................................................................................. 18

Starting Your Dryer ..................................................................... 18

Stopping Your Dryer .................................................................. 19

Pausing or Restarting ................................................................. 19

Control Locked ........................................................................... 19

Loading ....................................................................................... 19

Drying and Cycle Tips ................................................................ 19

Status Lights .............................................................................. 20

Cycles ......................................................................................... 20

Additional Features .................................................................... 21

Drying Rack ................................................................................ 22

DRYER CARE ............................................................................... 23

Cleaning the Dryer Location ...................................................... 23

Cleaning the Lint Screen ............................................................ 23

Cleaning the Dryer Interior ......................................................... 23

Removing Accumulated Lint ...................................................... 23

Vacation and Moving Care ......................................................... 24

Changing the Drum Light ........................................................... 24

TROUBLESHOOTING .................................................................. 24

ASSISTANCE OR SERVICE ......................................................... 26

WARRANTY .................................................................................. 28

1°

DRYERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or

"WARNING." These words mean:

You can be killed or seriously injured if you don't

immediately follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you

what can happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNUNG: To reduce the risk of fire, etectric shock, or injury to persons when using the dryer, follow basic

precautions, including the following:

[]

Read atI instructions before using the dryer.

Do not place items exposed to cooking oiIs in

your dryer, kems contaminated with cooking oils

may contribute to a chemicaI reaction that could

cause a Ioad to catch fire.

[] Do not dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with

gasoIine, dry=cleaning soIvents, other flammable,

or explosive substances as they give off vapors

that could ignite or explode.

[] Do not alIow chiIdren to pIay on or in the dryer.

Close supervision of children is necessary when

the dryer is used near chiIdren.

[] Before the dryer is removed from service or dis=

carded, remove the door to the drying compart

ment.

[] Do not reach into the dryer if the drum is moving.

[] Do not instalI or store the dryer where it will be

exposed to the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the dryer or

attempt any servicing unless specificaily recom=

mended in this Use and Care Guide or in published

user=repair instructions that you understand and have

the skiiIs to carry out.

[] Do not use fabric softeners or products to eiiminate

static unless recommended by the manufacturer of

the fabric softener or product.

[] Do not use heat to dry articIes containing foam rubber

or simiIady textured rubberqike materials.

[] Clean Iint screen before or after each Ioad.

[] Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint,

dust, and dirt.

[] The interior of the dryer and exhaust vent should be

cleaned periodicaily by qualified service personnel.

[] See installation instructions for grounding require

ments.

SAVE THESE iNSTRUCTiONS

INSTALLATION

INSTRUCTIONS

Check that you have everything necessary for correct installation.

Proper installation is your responsibility.

• Flat-blade screwdriver • Safety glasses

• Adjustable wrench that • Vent clamps

opens to 1 in. (2.5 cm) or

hex-head socket wrench • Caulking gun and

compound (for installing

(for adjusting dryer feet) new exhaust vent)

• Level • Gloves

• Wire stripper (direct wire

installations) • Tin snips (new vent

installations)

• #2 Phillips screwdriver • 1Ain. nut driver

Parts supplied

Remove parts packages from dryer drum. Check that all parts are

included.

• Door Reversal Kit

Parts needed

Check local codes. Check existing electrical supply and venting.

See "Electrical Requirements" and "Venting Requirements"

before purchasing parts.

• For close-clearance installations between 31.5 in. (80.01 cm)

and 37 in. (93.98 cm), see "Plan Vent System" section for

venting requirements.

I_ 37, _l

(93=98 cm)

Mobile home installations require metal exhaust system hardware

available for purchase from the dealer from whom you purchased

your dryer. For further information, please refer to the "Assistance

or Service" section of this manual.

Are you placing the dryer on a pedestal? You may purchase a

pedestal separately for this dryer. This pedestal will add about

13 in. (33 cm) to the height of your unit for a total height of

approximately 51 in. (130 cm).

• Parts package.

4 Leveling legs

NOTE: Do not use leveling legs if installing the dryer on a

pedestal.

Optional pedestal

To order, call the dealer from whom you purchased your dryer or

refer to the "Assistance or Service" section of this manual. Ask

for Part Number LAB2700LQ (White) or LAB2700LT (Biscuit).

E×ploeion Hazard

Keep flammable rnateriaJe and vapors, such as

gasoline, away from dryer.

Place dryer at teaet 18 inches (46 cm) above the

floor for a garage installation.

Failure to do so can result in death, explosion,

or fire.

You will need

• A location that allows for proper exhaust installation. See

"Venting Requirements."

• A separate 30 amp circuit.

• A grounded electrical outlet located within 2 ft (61 cm) of

either side of the dryer. See "Electrical Requirements."

• A sturdy floor to support the total dryer weight of 200 Ibs

(90.7 kg). The combined weight of a companion appliance

should also be considered.

A level floor with a maximum slope of 1 in. (2.5 cm) under

entire dryer. If slope is greater than 1 in. (2.5 cm), install

Extended Dryer Feet Kit, Part No. 279810. Clothes may not

tumble properly and automatic sensor cycles may not

operate correctly if dryer is not level.

• For a garage installation, you will need to place the dryer at

least 18 in. (46 cm) above the floor. If using a pedestal, you

will need an additional 6 in. (15.24 cm).

Do not operate your dryer at temperatures below 45°F (7°C). At

lower temperatures, the dryer might not shut off at the end of an

automatic cycle. This can result in longer drying times.

Install the dryer where it is protected from water and/or weather.

Check code requirements. Some codes limit, or do not permit,

installation of the dryer in garages, closets, mobile homes, or

sleeping quarters. Contact your local building inspector.

Installation clearances

• The location must be large enough to fully open the dryer

door.

• Additional spacing should be considered for ease of

installation and servicing.

• Additional clearances might be required for wall, door and

floor moldings.

• Additional spacing of I in. (2.5 cm) on all sides of the dryer is

recommended to reduce noise transfer.

• Companion appliance spacing should also be considered.

Dryer Dimensions

(98,52 cm)

* Most installations require a minimum 51/2in. (14 cm) clearance

behind the dryer for the exhaust vent with elbow. See "Venting

Requirements."

Minimum installation spacing for custom undercounter

installation

The dimensions shown are for the minimum spacing allowed.

Custom undercounter installation -Dryer only

0" -- 27" -- 0"

(0ore)"--_l_[(ss.s cm'T-_l<- (0ore)

Minimum installation spacing for recessed or closet

installation, with or without a pedestal

• The dimensions shown are for the minimum spacing allowed.

For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.

Louvered doors with equivalent ventilation openings are

acceptable.

Closet installation - Dryer only

_'_ 48,,2

(310 cm2) -

24"2

(155 cm 2)

I0"I* 31,5"_1 0"I

(0cm) (80cm) (0cm)

1. Side view- closet or confined area

2. Closet door with vents

._.(7,6 cm)

(7.6 cm)

Recessed or closet installation -Dryer on pedestal

0,, '0,,

(0 cm) (58,6 cm) (0 cm}

IH 1-1,4 4

H _, 15"min.

10"_ s_.5"_'10" I

(0cm)(80cm) (0cm)

1. Recessed area

2. Side view -closet or confined area

Minimum installation spacing for cabinet installation

• The dimensions shown are for the minimum spacing allowed.

• For cabinet installation, with a door, minimum ventilation

openings in the top of the cabinet are required.

" . ) 7" (17.8 cm)

0 31_/2 0 ......

(Ocm) (80.Ocm) (Ocm)(Ocrn) (68.6cm) (Ocm)

Mobile home-additional installation requirements

This dryer is suitable for mobile home installations.

The installation must conform to the Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280

(formerly the Federal Standard for Mobile Home Construction

and Safety, Title 24, HUD Part 280).

Mobile home installations require:

• Metal exhaust system hardware which is available for

purchase from your dealer.

Special provisions must be made in mobile homes to

introduce outside air into the dryer. The opening (such as a

nearby window) should be at least twice as large as the dryer

exhaust opening.

It is your responsibility

• To contact a qualified electrical installer.

• To be sure that the electrical connection is adequate and in

conformance with the National Electrical Code, ANSI/NFPA

70-latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association, Batterymarch Park,

Quincy, MA 02269.

To supply the required 3 or 4 wire, single phase, 120/240-volt,

60-Hz., AC-only electrical supply (or 3 or 4 wire, 120/208-volt

electrical supply, if specified on the serial/rating plate) on a

separate 30-amp circuit, fused on both sides of the line. A

time-delay fuse or circuit breaker is recommended. Connect

to an individual branch circuit. Do not have a fuse in the

neutral or grounding circuit.

• Do not use an extension cord.

• If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

• If local codes do not permit the connection of a cabinet

ground connector to the neutral wire, see "Optional 3-wire

connection" section.

• This dryer is manufactured with a 3-wire, cabinet-ground

conductor connected to the NEUTRAL (white or center wire)

of the wiring harness at the terminal block.

• Use a 4-wire conductor cord when the dryer is installed in a

mobile home or an area where local codes do not permit

grounding through the neutral.

If using a power supply cord:

Use a UL approved power supply cord kit marked for use with

clothes dryers. The kit should contain:

• A UL approved 30 amp power supply cord, rated 120/240

volt minimum. The cord should be type SRD or SRDT and be

at least 4 ft (1.22 m) long. The wires that connect to the dryer

must end in ring terminals or spade terminals with upturned

ends.

• A UL approved strain relief.

If your outlet looks like this:

3-wire receptacle (10-30t:?)

Then choose a 3-wire power supply cord with ring or spade

terminals and UL approved strain relief. The 3-wire power supply

cord, at least 4 ft (1.22 m) long, must have 3, No.-10 copper wires

and match a 3-wire receptacle of NEMA Type 10-30R.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire)

and be:

• Flexible armored cable or non-metallic sheathed copper

cable (with ground wire), protected with flexible metallic

conduit. All current-carrying wires must be insulated.

• 10 gauge solid copper wire (do not use aluminum).

• At least 5 ft (1.52 m) long.

GROUNDING INSTRUCTIONS

[] For a grounded, cord-connected dryer:

This dryer must be grounded, in the event of malfunction

or breakdown, grounding will reduce the risk of electric shock

by providing a path of least resistance for electric current. This

dryer uses a cord having an equ(pment-grounding

conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and ground-

ed in accordance with all local codes and ordinances.

[] For a permanently connected dryer:

This dryer must be connected to a grounded meta(, permanent

wiring system, or an equipment-grounding conductor must be

run with the circuit conductors and connected to the equip-

ment-grounding terminal or lead on the dryer.

WARN(NG: improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qua)ified electrician or service representative or

personnel if you are in doubt as to whether the dryer is proper-

ly grounded. Do not modify the plug on the power supply cord:

(f it wiU not fit the outlet, have a proper outlet (nstai(ed by a

qualified electrician.

SAVE THESE INSTRUCTIONS

4-wire receptacle (14-30R)

Then choose a 4-wire power supply cord with ring or spade

terminals and UL approved strain relief. The 4-wire power supply

cord, at least 4 ft (1.22 m) long, must have 4, 10 gauge solid

copper wires and match a 4-wire receptacle of NEMA Type

14-30R. The ground wire (ground conductor) may be either green

or bare. The neutral conductor must be identified by a white

cover.

Power Supply Cord Direct Wire

Fire Hazard

Use a new UL approved 30 amp power

supply cord.

Use a UL approved strain relief.

Disconnect power before making etectrica_

connections.

Connect neutra_ wire (white or center wire) to

center termina_ (silver).

Ground wire (green or bare wire) must be

connected to green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (go_d).

Securely tighten aH etectrica_ connections.

Failure to do so can result in death, fire, or

etectrica_ shock.

Fire Hazard

Use !0 gauge solid copper wire.

Use a UL approved strain relief.

Disconnect power before making etectrica_

connections.

Connect neutra_ wire (white or center wire) to

center termina_ (silver).

Ground wire (green or bare wire) must be

connected to green ground connector.

Connect remaining 2 supply wires to remaining

2 terminals (go_d).

Securely tighten aH etectrica_ connections.

Faiture to do so can result in death, fire, or

etectrica_ shock.

1. Disconnect power.

2. Remove the hold-down screw and terminal block cover.

Assemble a 3/4in. (1.9 cm) UL approved strain relief (UL

marking on strain relief) into the hole below the terminal block

opening. Tighten strain relief screws just enough to hold the

two clamp sections together. Put power supply cord through

the strain relief. The strain relief should have a tight fit with the

dryer cabinet and be in a horizontal position.

Now complete installation following instructions for your type

of electrical connection:

4-wire (recommended)

3-wire (if 4-wire is not available

1. Terminal block cover and hold-down screw

2. External ground connector

3. Neutral grounding wire (green/yeflew)

4. Center, silver-colored terminal-block screw

Electrical Connection Options

If your home has: And you will be Go to Section

connecting to:

4-wire receptacle A UL listed, 4-wire connection:

(NEMA Type 14-30R) 120/240 volt Power supply cord

minimum, 30

amp, dryer

power supply

cord*

4-wire direct A fused 4-wire connection:

disconnect or Direct Wire

circuit breaker

box*

3-wire receptacle A UL listed,

(NEMA type 10-30R) 120/240 volt

_j_ minimum, 30

amp., dryer

power supply

cord*

3-wire connection:

Power supply cord

3-wire direct A fused 3-wire connection:

disconnect or Direct Wire

circuit breaker

I.... --I box*

* If local codes do not permit the connection of a frame-

grounding conductor to the neutral wire, go to "Optional

3-wire Connection" section.

4-wire connection: Power supply cord

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire

connections.

5 7

1.4-wire receptacle (NEMA type 14-30R)

2. 4-prong plug

3. Ground prong

4. Neutral prong

5. Spade terminals with upturned ends

6. 3/4in. (1.9 cm) UL approved strain relief

7. Ring terminals

Remove center terminal block screw.

Remove appliance ground wire (green with yellow stripes)

from external ground connector screw. Fasten it under center,

silver colored terminal block screw.

1, External ground connector -Dotted line shows position

of NEUTRAL ground wire before being moved to center

terminal block screw

2. Center silver-colored terminal block screw

3. Green/yellow wire of harness

3. Connect ground wire (green or bare) of power supply cord to

external ground conductor screw. Tighten screw.

4. Connect neutral wire (white or center wire) of power supply

cord under center screw of the terminal block.

3.............

1. External ground connector

2. Green or bare copper wire of power supply cord

3. _in. (1.9cm) UL-Iisted strain relief

4. Center silver-colored terminal block screw

5. Neutral grounding wire (green/yeflow)

6. Neutral wire (white or center wire)

5. Connect the other wires to outer terminal block screws.

Tighten screws.

6. Tighten strain relief screws.

7. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

4-wire connection: Direct wire

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire

connections.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer

can be moved if needed.

Strip 5 in. (12.7 cm) of outer covering from end of cable, leaving

bare ground wire at 5 in. (12.7 cm). Cut 11/2in. (3.8 cm) from 3

remaining wires. Strip insulation back 1 in. (2.5 cm). Shape ends

of wires into a hook shape.

When connecting to the terminal block, place the hooked end of

the wire under the screw of the terminal block (hook facing right),

squeeze hooked end together and tighten screw, See example

below.

1. Remove center terminal block screw.

2. Remove appliance ground wire (green with yellow stripes)

from external ground connector screw. Fasten it under center,

silver colored terminal block screw.

3. Connect ground wire (green or bare) of power supply cable to

external ground conductor screw, Tighten screw.

Place the hooked ends of the other power supply cable wires

under the outer terminal block screws (hooks facing right).

Squeeze hooked ends together. Tighten screws.

!I !!

6. Tighten strain relief screws.

7. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

3-wire connection: Power supply cord

Use where local codes permit connecting cabinet-ground

conductor to neutral wire.

7 6

1.3-wire receptacle (NEMA type 10-30R)

2. 3-wire plug

3. Neutral prong

4. Spade terminals with up turned ends

5. _in. (1.9 cm) UL approved strain relief

6. Ring terminals

7. Neutral (white or center wire)

Loosen or remove center terminal block screw,

Connect neutral wire (white or center wire) of power supply

cord to the center, silver colored terminal screw of the

terminal block. Tighten screw.

1. External ground connector

2. Green or bare copper wire of power supply cord

3. _in. (!.9 cm) UL-Iisted strain relief

4. Center silver-colored terminal block screw

5. Neutral grounding wire (green/yellow)

6. Neutral wire (white or center wire)

Place the hooked end of the neutral wire (white wire) of power

supply cable under the center screw of terminal block (hook

facing right), Squeeze hooked end together. Tighten screw.

!. External ground connector

2. Neutral grounding wire (green/yellow)

3. Center silver-colored terminal block screw

4. Neutral wire (white or center wire)

5. ¾in. (1.9 cm) UL-Iisted strain relief

3. Connect the other wires to outer terminal block screws.

Tighten screws.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

3-wire connection: Direct wire

Use where local codes permit connecting cabinet-ground

conductor to neutral wire.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer

can be moved if needed.

Strip 31/2in. (8.9 cm) of outer covering from end of cable. Strip

insulation back 1 in. (2.5 cm). If using 3-wire cable with ground

wire, cut bare wire even with outer covering. Shape ends of wires

into a hook shape.

When connecting to the terminal block, place the hooked end of

the wire under the screw of the terminal block (hook facing right),

squeeze hooked end together and tighten screw. See example

below.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

Optional 3-wire connection

Use for direct wire or power supply cord where local codes

do not permit connecting cabinet-ground conductor to

neutral wire.

1. Remove center terminal block screw.

2. Remove appliance ground wire (green with yellow stripes)

from external ground connector screw. Connect appliance

ground wire and the neutral wire (white or center wire) of

power supply cord/cable under center, silver colored terminal

block screw. Tighten screw.

3. Connect the other wires to outer terminal block screws.

Tighten screws.

!! !I

Loosen or remove center terminal block screw.

Place the hooked end of the neutral wire (white or center wire)

of power supply cable under the center screw of terminal

block (hook facing right). Squeeze hooked end together.

Tighten screw.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

6= Connect a separate copper ground wire from the external

ground connector screw to an adequate ground.

1. External ground connector

2. Neutral grounding wire (green/yellow)

3, Center silver-colored terminal block screw

4. Neutral wire (white or center wire)

5. _in. (!.9 crn) UL-llsted strain relief

Place the hooked ends of the other power supply cable wires

under the outer terminal block screws (hooks facing right).

Squeeze hooked ends together. Tighten screws.

!! !!

1. External ground connector

2. Neutral grounding wire (green/yellow)

3. Neutral wire (white or center wire)

4. Grounding path determined by a qualified electrician

Fire Hazard

Use a heavy metaJ vent.

Do not use a pJaetic vent.

Do not use a metaJ foil vent.

Failure to follow these instructions can result in

death or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE

EXHAUSTED OUTDOORS.

4 in. (10.2 cm) heavy metal exhaust vent and clamps must be

used. DURASAFE TM vent products are recommended.

DURASAFF Mvent products can be purchased from your dealer

or by calling Whirlpool Parts and Accessories, For more

information, see the "Assistance or Service" section of this

manual,

• The dryer exhaust must not be connected into any gas vent,

chimney, wall, ceiling, or a concealed space of a building.

• Do not use an exhaust hood with a magnetic latch.

• Do not install flexible metal vent in enclosed walls, ceilings or

floors.

• Use clamps to seal all joints. Exhaust vent must not be

connected or secured with screws or other fastening devices

which extend into the interior of the duct. Do not use duct tape.

IMPORTANT: Observe all governing codes and ordinances.

improper venting can cause moisture and mintto collect

indoors, which may resumt in:

[] Moisture damage to woodwork, furniture, paint, wall-

paper, carpets, etc=

[] Housecleaning problems and health problems=

Use a heavy metal vent. Do not use plastic or metal foil vent.

Rigid metal vent is recommended to prevent crushing and

kinking.

Flexible metal vent must be fully extended and supported when

the dryer is in its final position. Remove excess flexible metal vent

to avoid sagging and kinking that can result in reduced airflow

and poor performance.

An exhaust hood should cap the vent to prevent rodents and

insects from entering the home.

Exhaust hood must be at least 12 in. (30.5 cm) from the ground or

any object that is in the path of the exhaust (such as flowers,

rocks or bushes, etc.).

If using an existing vent system, clean lint from the entire length

of the system and make sure exhaust hood is not plugged with

lint. Replace any plastic or metal foil vent with rigid metal or

flexible metal vent.

Typical exhaust installations

Typical installations vent the dryer from the rear of the dryer.

Other installations are possible.

i ii_¸

1. Dryer

2. Elbow

3. Wall

4. Exhaust hood

5. Clamps

6. Rigid metal or flexible metal vent

7. Vent length necessary to connect elbows

8. Exhaust outlet

Optional exhaust installations

This dryer can be converted to exhaust out the right side, left

side, or through the bottom.

Fire Hazard

Cover unused exhaust holes with one of the

following kite:

279818 (white)

279925 (biscuit}

Contact your JoeaJdeaJer.

Failure to follow these instructions can result in

death, fire, etectrica! shock, or serious injury.

1. Standard rear offset exhaust installation

2. Left or right side exhaust installation

3. Bottom exhaust installation (Not an option with

pedestal installations.)

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for

your installation. Two close-clearance installations are shown.

Refer to the manufacturer's instructions.

I "_?jzz_z-

i"i.... ii

i i

i ..... /f

," I F /;"

i ii

I i u

I 2

1. Over-The-Top installation (also available with one offset elbow)

2. Periscope installation

NOTE: The following kits for close clearance alternate

installations are available for purchase. Please see the

"Assistance or Service" section of this manual to order.

•Over-The-Top Installation:

Part Number 4396028

• Periscope Installation (For use with dryer vent to wall vent

mismatch):

Part Number 4396037 - 0 in. (0 cm) to 18 in. (45.72 cm)

mismatch

Part Number 4396011 - 18 in. (45.72 cm) to 29 in. (73.66 cm)

mismatch

Part Number 4396014 - 29 in. (73.66 cm) to 50 in. (127 cm)

mismatch

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible

portion of the mobile home structure and must not terminate

beneath the mobile home. Terminate the exhaust vent outside.

Determine Vent Length

1. Select the route that will provide the straightest and most

direct path outdoors. Plan the installation to use the fewest

number of elbows and turns. When using elbows or making

turns, allow as much room as possible. Bend vent gradually

to avoid kinking. Avoid 90° turns.

2= Determine vent length.

The maximum length of the exhaust system depends upon:

• The type of vent (rigid metal or flexible metal).

• The number of elbows used.

• The type of hood.

Recommended hood styles are shown here.

(10.2 cm)

1.Louvered hood style

2. Box hood style

The angled hood style (shown following) is acceptable.

2.5"

See the exhaust vent length chart that matches your hood

type for the maximum vent lengths you can use.

Exhaust systems longer than specified will:

• Shorten the life of the dryer.

• Reduce performance, resulting in longer drying times and

increased energy usage.

Determine the number of elbows you will need.

IMPORTANT: Do not use vent runs longer than those

specified in the Vent Length Chart.

The following chart helps you determine your maximum vent

length based on the number of 90° turns or elbows you will

need and the type of vent (rigid or flexible metal) and hood

that you will use.

Vent Length Chart

Number of Type of Box or Angled

90° turns vent Louvered hoods

or elbows hoods

0 Rigid metal 64 ft (20 m) 58 ft (17.7 m)

Flexible metal 36 ft (11 m) 28 ft (8.5 m)

1 Rigid metal 54 ft (16.5 m) 48 ft (14.6 m)

Flexible metal 31 ft (9.4 m) 23 ft (7 m)

2 Rigid metal 44 ft (13.4 m) 38 ft (11.6 m)

Flexible metal 27 ft (8.2 m) 19 ft (5.8 m)

3 Rigid metal 35 ft (10.7 m) 29 ft (8.8 m)

Flexible metal 25 ft (7.6 m) 17 ft (5.2 m)

4 Rigid metal 27 ft (8.2 m) 21 ft (6.4 m)

Flexible metal 23 ft (7 m) 15 ft (4.6 m)

NOTE: Side and bottom exhaust installations have a 90° turn

inside the dryer. To determine maximum exhaust length, add 1

90° turn to the chart.

1. (Optional) Put on safety glasses and gloves.

2. Install exhaust hood. Use caulking compound to seal exterior

wall opening around exhaust hood.

3. Connect vent to exhaust hood. Vent must fit inside exhaust

hood. Secure vent to exhaust hood with 4 in. (10.2 cm)

clamp.

4. Run vent to dryer location. Use the straightest path possible.

See "Determine Vent Length." Avoid 90 ° turns. Use clamps to

seal all joints. Do not use duct tape, screws or other fastening

devices that extend into the interior of the vent to secure

vent.

2. Firmly grasp the body of the dryer (not the console panel).

Gently lay the dryer on the cardboard.

Examine the leveling legs. Find the diamond marking.

Screw the legs into the leg holes by hand. Use a wrench to

finish turning the legs until the diamond marking is no longer

visible.

5. Place a carton corner post under each of the 2 dryer back

corners. Stand the dryer up. Slide the dryer on the corner

posts until it is close to its final location. Leave enough room

to connect the exhaust vent.

6. Once connection is made and dryer is in final location,

remove corner posts and cardboard.

Check the levelness of the dryer. Check levelness first

side-to-side, then front-to-back.

Excessive Weight Hazard

Use two or more people to move and install

dryer.

Failure to do so can result in back or other injury.

1. To protect the floor, use a large flat piece of cardboard from

the dryer carton. Place cardboard under the entire back edge

of the dryer. See illustration.

If the dryer is not level, prop up the dryer using a wood block.

Use a wrench to adjust the legs up or down and check again for

levelness.

NOTE: It might be necessary to level the dryer again after it has

been moved into its final position.

1. Using a 4 in. (10.2 cm) clamp, connect vent to exhaust outlet

in dryer. If connecting to existing vent, make sure the vent is

clean. The dryer vent must fit over the dryer exhaust outlet

and inside the exhaust hood. Make sure the vent is secured

to exhaust hood with a 4 in. (10.2 cm) clamp.

2. Move dryer into final position. Do not crush or kink vent.

Make sure dryer is level.

3. (On gas models) Check to be sure there are no kinks in the

flexible gas line.

You can change your door swing from a right-side opening to a

left-side opening, if desired.

Locate the door reversing kit that was shipped in the drum of

your dryer. You will need these parts to complete the door

reversal.

Loosen door trim

1. Place a towel or soft cloth on top of the dryer or work space

to protect the surface.

2. Loosen the plastic trim above and below the handle filler.

Carefully pull out on the trim until it unsnaps. Remove the

handle filler and set aside.

Remove the door

1. Open the dryer door. Remove the 5 screws that hold the door

hinge on the front panel of the dryer. Loosen, but do not

remove, the screw with the top keyhole opening LAST

(second from the top). !

Lift and pull forward on the door so that the screwhead clears

the keyhole. Remove the door.

Lay the dryer door on a flat, protected surface with the inside

door assembly facing up. Remove the 2 screws holding the

handle to the door. Pull handle straight out and set aside. A

new handle is provided.

.....2

1. Plastic trim

2. Handle filler

Loosen the plastic trim above and below the hinge cover.

Carefully pull out on the trim until it unsnaps. Remove the

hinge cover and set aside.

1. Plastic trim

2. Hinge cover

Keep the original handle filler and hinge cover in case you

decide to return the door to its original position.

A new handle filler and hinge cover are provided in the door

reversing kit that will be installed in a later step.

NOTE: Keep this handle in case you decide to return the door

to its original position.

Remove the 6 screws to release the outer door assembly

from the inner door assembly (see illustration). It is important

that you remove ONLY the 6 indicated screws.

5. Lift the inner door assembly off of the outer door assembly.

Set the outer door assembly aside.

Reverse the hinge and hinge bracket

1. Place the inner door, screwhead side up, on the work surface.

2. Remove the 4 screws that hold the hinge to the door.

Remove the 2 screws that hold the handle bracket to the

door.

Insert the new handle into the side opening of the door. Make

sure the handle seats all the way in, and the holes line up with

the holes in the door. Reattach with 2 screws.

Use a small flat-head screwdriver to remove hole plugs in the

door opening. Slide the head of the screwdriver under the

cap of each hole plug, being careful not to scratch the dryer

surface. Lift up. Remove the hole plugs in the door opening

and insert in the opposite side.

6, Insert a screw in the second opening from the top of the

hinge opening and partially tighten. Hang the door by placing

the top hinge keyhole over the second screwhead and tighten

the screw. By putting this screw in first, the door will hang in

place while you insert and tighten the remaining 4 screws.

4. Move hinge to the other side and reattach.

5. Move handle bracket to the other side and reattach.

6. Set the inner door assembly aside.

Reinstalling the door

1. Check for fingerprints on the glass. Clean if necessary.

2. Place the inner door assembly into the outer door assembly.

Align the hinge in the opening on the side. To fit correctly, the

inside door assembly edge is completely inside the outside

door assembly edge.

3. Reassemble the inner and outer door assemblies with the 6

screws.

Install new handle filler and hinge cover

1. Using the new handle filler provided in the reversing kit, hook

the top of the handle filler onto the loosened upper door trim.

Snap the joined pieces into place. You may need to use the

heel of your hand to firmly snap the pieces back into place.

2. Hook the bottom of the handle filler onto the lower door trim

and snap into place.

3. Repeat steps 1 and 2 to install the hinge cover on the

opposite side.

4. Close the door and check that it latches securely.

1. Check to be sure all parts are now installed. If there is an

extra part, go back through the steps to see which step was

skipped.

2. Check to be sure you have all of your tools.

3. Dispose of all packaging materials.

4. Check the dryer's final location. Be sure the vent is not

crushed or kinked.

5. Check to be sure the dryer is level. (See "Level Dryer.")

6. Plug into a grounded outlet. Turn power on.

7. Remove the blue protective film on the console and any tape

remaining on the dryer.

8. Read "Dryer Use."

9. Wipe the dryer drum interior thoroughly with a damp cloth to

remove any dust.

10. Set the dryer on a full heat cycle (not an air cycle) for 20

minutes and start the dryer.

If the dryer will not start, check the following:

• Controls are set in a running or "On" position.

• Start button has been pushed firmly.

• Dryer is plugged into a grounded outlet.

• Electrical supplyis connected.

• House fuse is intact and tight; or circuit breaker has not

tripped.

• Dryer door is closed.

11. When the dryer has been running for 5 minutes, open the

dryer door and feel for heat.

If you do not feel heat, turn the dryer off and check the

following:

• There may be 2 fuses or circuit breakers for the dryer. Check

to make sure both fuses are intact and tight, or that both

circuit breakers have not tripped. If there is still no heat,

contact a qualified technician.

NOTE: You may notice a burning odor when the dryer is first

heated. This odor is common when the heating element is first

used. The odor will go away.

DRYERUSE

<>H_gh

(Medmm

0Low ;Louder

oExlroLow :) 5alter

o0,_ oAir O_#y 0Off

Wt#_We5hietd _mp_rst_re E_dOf CycleSignal

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Do not dry anything that has ever had anything

flammable on it (even after washing).

Failure to follow these instructions can result in

death, explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before

operating this appliance.

The following is a guide to starting your dryer. Please refer to

specific sections of this manual for more detailed information.

1. Clean lint screen before or after each cycle.

2. Place laundry into dryer and shut door. See "Loading."

3. Rotate the dial to select either an Automatic or Manual Cycle

then press the CONTROL ON button. The preset settings and

drying time for the cycle chosen will be displayed.

To use an Automatic Cycle

Point the dial to an Automatic Cycle.

Select DRYNESS LEVEL to adjust how dry you want the

load to be. The time displayed is an estimated length of

the cycle based on the Dryness Level selected. As the

cycle runs, the control senses the dryness of the load and

adjusts the time automatically for the selected Dryness

Level.

0More

0Lees

Fire Hazard

No washer can completely remove oil

Do not dry anything that has ever had any type of

oit on it (including cooking oits).

Items containing foam, rubber, or plastic must be

dried on a c_othesHne or by using an Air Cycle.

Failure to follow these instructions can resutt in

death or fire.

Dryness

Levd

NOTE: Time is not adjustable for Automatic Cycles. Pressing

the More Time or Less Time buttons will cause a triple beep,

indicating that the time cannot be changed.

Press the WRINKLE SHIELD TM feature button if this

option is desired.

Press the END OF CYCLE SIGNAL button to set signal

volume to desired level.

Press (and hold) HOLD TO START button until dryer starts

(about 1 second).

Once an Automatic cycle has started, the WRINKLE

SHIELD TM feature and the End of Cycle Signal level can be

adjusted. Press the PAUSE/CANCEL key twice to stop the

dryer and clear the settings, allowing you to select another

cycle and Dryness Level.

To use a Manual Cycle

• Rotate the dial to select a Manual Cycle.

Press MORE TIME or LESS TIME until the desired drying time

is displayed. Tap MORE TIME or LESS TIME and the time will

change by 1-minute intervals. Press and hold MORE TIME or

LESS TIME and the time will change by 5-minute intervals.

The initial time displayed is the actual drying time.

Mote

Time

Less

_me

NOTE: The More Time or Less Time feature can be used only

with Manual Cycles.

• Press TEMPERATURE until the desired temperature

glows.

NOTE: Pressing the Dryness Level button will cause the triple

beep indicating that this option is not selectable. Also, a

Dryness Level is not indicated.

• Press the WRINKLE SHIELD TM feature button if this

option is desired.

• Press the END OF CYCLE SIGNAL button to set volume

to desired level.

• Press (and hold) HOLD TO START button until dryer starts

(about 1 second).

While a Manual Cycle is running, you can change the settings

for Time, Temperature, the WRINKLE SHIELD TM feature, and

the End of Cycle Signal. Press the PAUSE/CANCEL key twice

to stop the dryer and clear the settings, allowing you to select

another cycle.

To unlock:

Press and hold the END OF CYCLE SIGNAL button for three

seconds to turn this feature off.

NOTE: When the dryer is running and Control Locked is on, the

dryer can be stopped by pressing the Pause/Cancel button, but

can't be restarted until the control is unlocked.

Properly loading your dryer can lower your utility bill and prolong

the life of your garments.

Loading suggestions

•Load the dryer by the amount of space items take up, not by

their weight.

• Do not overload the dryer. This causes wrinkling and uneven

drying.

Super Capacity Plus Dryers

Heavy Work Clothes

4 jeans 2 sweatpants

4 workpants 2 sweatshirts

4 workshirts

Towels

10 bath towels

10 hand towels 14 washcloths

Mixed Load

3 sheets (1 king, 2 twin) 9 T-shirts

4 pillowcases 9 shorts

3 shirts 10 handkerchiefs

3 blouses

To stop your dryer at any time

Press PAUSE/CANCELtwice or open the door.

To pause the dryer at any time

Open the door or press PAUSE/CANCEL once.

To restart the dryer

Close the door and press (and hold) HOLD TO START button until

dryer starts.

NOTE: Drying will continue from where the cycle was interrupted

if you close the door and press Start within 5 minutes. If the cycle

is interrupted for more than 5 minutes, the dryer will shut off.

Select new cycle settings before restarting the dryer.

This feature allows you to lock your settings to prevent

unintended use of the dryer. You can also use the Control Locked

feature to prevent unintended cycle or option changes during

dryer operation.

To enable the Control Locked feature when dryer is

running:

Press and hold the END OF CYCLE SIGNAL button for three

seconds. The control is locked when a single beep is heard and

the Control Locked status light is on.

• When the dryer is off, it is not necessary to press the Control

On button before activating the Control Locked feature.

Select the correct cycle and dryness level or temperature for your

load. If an Automatic Cycle is running, the display shows the

estimated cycle time when your dryer is automatically sensing

the dryness level of your load. If a Manual Cycle is running, the

display shows the exact number of minutes remaining in the

cycle.

Cool Down tumbles the load without heat during the last few

minutes of all cycles. Cool Down makes the loads easier to

handle and reduces wrinkling. The length of the Cool Down

depends on the load size and dryness level.

Drying tips

• Follow care label directions when they are available.

• If you use fabric softener sheets, use only ones labeled as

dryer safe. Follow package instructions.

• Remove the load from the dryer as soon as tumbling stops to

reduce wrinkling. This is especially important for permanent

press, knits, and synthetic fabrics.

• Avoid drying heavy work clothes with lighter fabrics. This

could cause overdrying of lighter fabrics, leading to increased

shrinkage or wrinkling.

Cycletips

• Drymostloadsusingthepresetcyclesettings,

• Refer to the Automatic or Manual Preset Cycle Settings chart

(in the "Cycles" section) for a guide to drying various loads.

Drying temperature and Dryness Level are preset when

you choose an Automatic Cycle. You can choose a

different dryness level, depending on your load by

pressing the DRYNESS LEVEL button to select MORE or

LESS.

• If you wish to adjust the cycle length of a Manual Cycle,

you must press MORE TIME or LESS TIME. Adjust the

temperature of a Manual Cycle by pressing

TEMPERATURE until the desired temperature is selected.

NOTE: You cannot choose a Dryness Level with Manual

Cycles.

You may follow the progress of your dryer with the drying Status

indicator lights.

5tetus

0Sensing

0Wet

0Damp

OCoolDown

0 Cycle Complete

0Wrinkle Shield

0ControlLocked

Sensing

When the dryer is first turned on, the SENSING light glows until a

wet item is detected.

• In an Automatic Cycle, if a wet item has not been detected

within 10 minutes, the Sensing light will turn off and the dryer

will shut down.

• In a Manual Cycle, if a wet item is not detected after 10

minutes the Wet light turns on and the selected cycle

continues.

Wet

The WET light will turn on when a wet item has been detected in

the dryer. The Wet light will remain on until:

• The damp dry point is reached in an Automatic Cycle.

• The dryer enters the cool down period in a Manual Cycle.

Damp

The DAMP light indicates that the load has reached the damp dry

level.

NOTE: The Damp light is not used with manual cycles.

Cool Down

The COOL DOWN light glows during the cool down part of the

cycle. Laundry is cooling down for ease in handling.

Cycle Complete

This light glows when a drying cycle is finished. If the WRINKLE

SHIELD TM feature has been selected, the WRINKLE SHIELD TM

feature indicator light will also be on.

The Cycle Complete light turns off one hour after the end of a

drying cycle (including the WRINKLE SHIELD TM cycle of 2 hours),

when Pause/Cancel is pressed, or when the door is opened.

WRINKLE SHIELD TM Feature

The WRINKLE SHIELD feature light glows when this option is

selected. This indicator stays on with the Cycle Complete light.

Control Locked

The CONTROL LOCKED light glows when this option is enabled.

Indicator lights

Other indicator lights on the control panel show Cycle, Temper-

ature, and End of Cycle settings selected.

The time display will indicate the estimated or actual time

remaining in a cycle.

Select the drying cycle that matches the type of load you are

drying (see Automatic Preset or Manual Preset Cycle Settings

charts).

Cycle control knob

Automatic Cycles allow you to match the cycle to the load you

are drying. See the following "Automatic Preset Cycle Settings"

chart. Each cycle dries certain fabrics at the recommended

temperature. A sensor detects the moisture in the load and

automatically adjusts the drying time for optimal drying.

Heavy Duty

Use this cycle to get High heat for heavy fabrics such as cotton

towels or bedspreads.

Normal

Use this cycle to get Medium heat for drying sturdy fabrics such

as work clothes.

Casual

Use this cycle to get Medium heat for drying no-iron fabrics, such

as sport shirts, casual business clothes and permanent press

blends.

Delicate

Use this cycle to get Low heat for drying synthetic fabrics,

washable knit fabrics and no-iron finishes.

Super Delicate

Use this cycle to get Extra Low heat to gently dry items such as

lingerie, exercise wear, or sheer curtains.

Automatic Preset Cycle Settings

Automatic Cycles Temp. Time*

Load Type (Minutes)

HEAVY DUTY High 40

Heavyweight, towels

NORMAL Medium 34

Corduroys, work clothes

CASUAL Medium 36

Permanent press, synthetics

DELICATE Low 28

Lingerie, blouses, washable

woolens

SUPER DELICATE Extra Low 22

Exercise wear, sheer curtains, lace

* Estimated Time with Dryness Level (medium) setting.

Use Manual Cycles to select a specific amount of drying time and

a drying temperature. When a Manual Cycle is selected, the

ESTIMATED TIME REMAINING display shows the actual time

remaining in your cycle. You can change the actual time in the

cycle by pressing MORE TIME or LESS TIME.

Timed Dry

Use this cycle to complete drying if items are still damp after an

Automatic Cycle. Timed Dry is also useful for drying heavyweight

and bulky items, such as bedspreads and work clothes.

Touch Up

Use this setting to remove wrinkles from items, such as clothes

packed in a suitcase or items wrinkled from being left in the dryer

too long.

Quick Dry

Use this cycle for drying small loads or loads that need a short

drying time.

Manual Preset Cycle Settings

Manual Cycles Temp. Default Time

Load Type (Minutes)

TIMED DRY High 40

Heavyweight, bulk,

bedspreads, work clothes

TOUCH UP Medium 20

Remove wrinkles

QUICK DRY High 27

Small loads

WRINKLE SHIELD TM Feature

When you are unable to remove a load of clothes from the dryer

as soon as it stops, wrinkles can form. The WRINKLE SHIELD TM

feature periodically tumbles, rearranges and fluffs the load to

avoid wrinkles.

• Press the WRINKLE SHIELD TM feature to get up to 120

minutes of heat-free, periodic tumbling at the end of a cycle.

• Stop at any time by pressing the WRINKLE SHIELD TM feature

or opening the dryer door.

For the Casual Cycle, the WRINKLE SHIELD TM feature is

preset to "On." The other Automatic Cycles will retain the

WRINKLE SHIELD TM feature setting. (For example, if you

select the WRINKLE SHIELD TM feature in the Normal cycle,

the WRINKLE SHIELD TM feature will be on the next time you

select the Normal cycle.)

NOTE: If you do not select the WRINKLE SHIELD TM feature, the

dryer stops after the cool down period.

Temperature

Temperature settings are used with the Manual Cycles. Press

TEMPERATURE until the desired temperature setting glows.

Temperature settings cannot be used with the Automatic Cycles.

0High

0Me_um

0Low

0 _troLow

0Air Only

_mpe_tu_

_anualCydeson_

Air Only

Use the Air Only setting for items that require drying without heat

such as rubber, plastic and heat-sensitive fabrics. This chart

shows examples of items that can be dried using Air Only.

Type of Load Time*

(Minutes)

Foam rubber - pillows, padded bras, stuffed 20 - 30

toys

Plastic-Showercurtains, tableclothes 20-30

Rubbe_backed rugs 40-50

Olefin, polypropylene, sheer nylon 10 - 20

* Reset time to complete drying, if needed.

When using Air Only

• Check to see that coverings are securely stitched.

• Shake and fluff pillows by hand periodically during the cycle.

• Dry item completely. Foam rubber pillows are slow to dry.

NOTE: Automatic Cycles are not available when using the Air

Only setting.

End of Cycle Signal

The End of Cycle Signal produces an audible sound when the

drying cycle is finished. Promptly removing clothes at the end of

the cycle reduces wrinkling.

0Louder

0Softer

ooff

EndOf dyde Signet

Hold for _Seconds to

Lock I Unlock Control

Press and release the END OF CYCLE SIGNAL to adjust the

sound level or turn off the signal.

NOTE: When the WRINKLE SHIELD TM feature is selected and the

End of Cycle Signal is on, an audible sound will emit every five

minutes until the clothes are removed, or the WRINKLE

SHIELD TM feature is finished.

The drying rack is useful for drying items you would not

necessarily want to tumble dry or that you would normally line dry

(for example, sweaters).

To use the drying rack

Do not remove the lint screen.

1. Open dryer door.

1. Front edge

2. Place drying rack inside dryer drum, positioning the back wire

on the ledge of the inner dryer back panel. Push down on

front edge of drying rack to secure over the lint screen.

1. Dryer back panel

3. Put the wet items on top of the rack. Leave space between

the items so air can reach all the surfaces.

NOTE: Do not allow items to hang over the edge of the rack.

4. Close the door.

5. Select a timed drying cycle and temperature, or an air cycle.

Items containing foam, rubber, or plastic must be dried on a

clothesline or by using the Air Only temperature setting.

6. You must select a time by pressing MORE TIME or LESS

TIME. Reset time as needed to complete drying. Refer to the

following table.

7. Press (and hold) HOLD TO START button (about 1 second).

NOTE: You must remove rack for normal tumbling. Do not use

automatic cycles with the drying rack.

This chart shows examples of items that can be rack dried and

the suggested cycle, temperature setting and drying time. Actual

drying time will depend on the amount of moisture items hold.

Rack Dry Setting Temp Time*

Wool Sweaters Timed Low 60

Block to shape and lay flat on Dry

the rack

Stuffed toys or pillows Timed Low 60

Cotton or polyester fiber filled Dry

Stuffed toys or pillows Air Only N/A 90

Foam rubber filled (no heat)

Sneakers or canvas shoes Air Only N/A 90

(no heat)

*(Minutes) Reset time to complete drying, if needed.

DRYERCARE

Keep dryer area clear and free from items that would obstruct the

flow of combustion and ventilation air.

ExpJosion Hazard

Keep flammabJe materiaJs and vapors, such as

gasoline, away from dryer.

Place dryer at Jeast 18 inches (46 cm) above the

floor for a garage installation.

Failure to do so can result in death, explosion,

or fire.

Every load cleaning

The lint screen is located in the door opening of the dryer. Clean it

before or after each load. A screen blocked by lint can increase

drying time.

To clean

1. Pull the lint screen straight up. Roll lint off the screen with

your fingers. Do not rinse or wash screen to remove lint. Wet

lint is hard to remove.

2. Push the lint screen firmly back into place.

IMPORTANT:

• Do not run the dryer with the lint screen loose, damaged,

blocked, or missing. Doing so can cause overheating and

damage to both the dryer and fabrics.

Some towels made of synthetic fibers and natural fibers

(polyester and cotton blends) may shed more lint than other

towels, causing your dryer's lint screen to fill up faster. Be

sure to remove lint from the lint screen before and after drying

new towels.

• If lint falls off the screen into the dryer during removal, check

the exhaust hood and remove the lint. (See "Venting

Requirements.")

As needed cleaning

Laundry detergent and fabric softener residue can build up on the

lint screen. This buildup can cause longer drying times for your

clothes, or cause the dryer to stop before your load is completely

dry. The screen is probably clogged if lint falls off the screen.

Clean the lint screen with a nylon brush every 6 months, or more

frequently, if it becomes clogged due to a residue buildup.

To wash

1. Roll lint off the screen with your fingers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent. Scrub

lint screen with the brush to remove residue buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel. Replace screen

in dryer.

To clean dryer drum

1. Make a paste with powdered laundry detergent and very

warm water.

2. Apply paste to a soft cloth.

3. Apply a liquid, non-flammable household cleaner to the

stained area and rub with a soft cloth until all excess dye is

removed.

4. Wipe drum thoroughly with a damp cloth.

5. Tumble a load of clean cloths or towels to dry drum.

NOTE: Garments which contain unstable dyes, such as denim

blue jeans or brightly colored cotton items, may discolor the

dryer interior. These stains are not harmful to your dryer and will

not stain future loads of clothes. Dry unstable dye items inside

out to prevent dye transfer.

From Inside the Dryer Cabinet

Lint should be removed every 2 years or more often, depending

on dryer usage. Cleaning should be done by a qualified person.

From the Exhaust Vent

Lint should be removed every 2 years, or more often, depending

on dryer usage.

.... iii! i'ii!i!iiio , ii!:!i j!iill¸C! iiii :,,iii

Vacation care

Operate your dryer only when you are at home. If you will be on

vacation or not using your dryer for an extended period of time,

you should:

1. Unplug dryer or disconnect power.

2. Wash lint screen.

Moving care

1. Unplug dryer or disconnect power. Disconnect wiring if dryer

is direct wired.

2. Make sure leveling legs are secure in dryer base.

3. Use masking tape to secure dryer door.

The dryer light automatically turns on inside the dryer drum when

you open the door.

To change the drum light

1. Unplug dryer or disconnect power.

2. Open the dryer door. Locate the light bulb cover on the back

wall of the dryer. Remove the screw located in the lower right

corner of the cover. Remove the cover.

3. Turn bulb counterclockwise. Replace the bulb with a 10-watt

appliance bulb only. Replace the cover and secure with the

screw,

4. Plug in dryer or reconnect power.

TROUBLESHOOTING

First try the solutions suggested here and possibly avoid

the cost of a service call...

Dryer displaying code message

• "PF" (power failure), check the following:

Was the drying cycle interrupted by a power failure?

Press (and hold) HOLD TO START button to restart the dryer.

• "E" Variable (El, E2, E3) service codes:

Call for service.

Clothes are not drying satisfactorily

Check the following:

Is the lint screen clogged with lint?

Is the exhaust vent or outside exhaust hood clogged with lint,

restricting air movement? Run the dryer for 5-10 minutes.

Hold your hand under the outside exhaust hood to check air

movement. If you do not feel air movement, clean exhaust

system of lint or replace exhaust vent with heavy metal or

flexible metal vent. (See "Installation Instructions.")

Is the exhaust vent crushed or kinked? Replace with a heavy

metal vent. (See "Installation Instructions.")

Has a fuse blown, or a circuit breaker tripped? Electric dryers

use 2 household fuses or breakers. The drum may be turning,

but you may not have heat.

Has an air cycle been selected? Select the right cycle for the

types of garments being dried (see "Cycles").

Is the automatic cycle ending early? The load may not be

contacting the electronic sensor strips, level the dryer.

Are fabric softener sheets blocking the grille? Use only one

fabric softener sheet and only use it once.

Is the dryer located in a room with temperature below

45°F (7°C)?

Proper operation of dryer cycles requires temperatures above

45°F (7°C).

Was a cold rinse water used? Was the load very wet?

Expect longer drying times with items rinsed in cold water

and with items that hold moisture (cottons).

Is the load too large and heavy to dry quickly?

Separate the load to tumble freely.

Dryer will not run

•Checkthe following:

Is the power cord plugged in?

Has a fuse blown, or has circuit breaker tripped?

Was a regular fuse used? Use a time-delay fuse.

Is the dryer door firmly closed? If not, the time display will

blink.

Was HOLD TO START firmly pressed and held for at least 1

second?

Is a cycle selected?

Unusual sounds

•Has the dryer had a period of non-use?

If the dryer hasn't been used for a while, there may be a

thumping sound during the first few minutes of operation.

Lint on load

•Is the lint screen clogged?

Clean lint screen. Check for air movement.

•Is load properly sorted?

Sort lint givers (towels, chenille) from lint takers (corduroy,

synthetics). Also sort by color.

•Is the load too big or too heavy?

Dry smaller loads so lint can be carried to the lint screen.

•Was the load overdried?

Use correct dryer settings for load type (see "Cycles").

Overdrying can cause lint-attracting static electricity.

• Was paper or tissue left in pockets?

•Is pilling being mistaken for lint?

Pilling (surface fuzz) is caused by normal wear and

laundering.

Stains on load or color change

•Was dryer fabric softener properly used?

Add dryer fabric softener sheets at the beginning of the cycle

when the load is cold. Do not add fabric softener sheets to a

warm load.

•Were items soiled when placed in the dryer?

Items should be clean before being dried.

•Were items properly sorted?

Sort light colors from dark colors. Sort colorfast items from

noncolorfast items.

Items shrinking

•Was the dryer overloaded?

Dry smaller loads that can tumble freely.

•Did the load overdry?

Check the manufacturer's care label. Match dryer setting to

load type (see "Cycles").

Loads are wrinkled

•Was load removed from dryer at the end of the cycle?

•Was dryer overloaded?

Dry smaller loads that can tumble freely.

•Did load overdry?

Check the manufacturer's care label. Match dryer setting to

load type (see "Cycles").

Odors

•Have you recently been painting, staining or varnishing in

the area where your dryer is located?

If so, ventilate the area. When the odors or fumes are gone

from the area, re-wash and dry the clothing.

•Is the dryer being used for the first time?

The new electric heating element may have an odor. The odor

will be gone after the first cycle.

Garment damage

•Check the following:

Were zippers, snaps, and hooks left open?

Were strings and sashes tied to prevent tangling?

Were care label instructions followed?

Were items damaged before drying?

ASSISTANCEORSERVICE

Before calling for assistance or service, please check

"Troubleshooting." It may save you the cost of a service call. If

you still need help, follow the instructions below.

When calling, please know the purchase date and the complete

model and serial number of your appliance. This information will

help us to better respond to your request.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only FSP® factory specified parts. These parts will fit right

and work right because they are made with the same precision

used to build every new WHIRLPOOL ®appliance. To locate FSP®

replacement parts in your area, call our Customer Interaction

Center telephone number or your nearest designated service

center.

For assistance and service

Call the Whirlpool Customer Interaction Center toll free:

1-800 -253-1301.

Our consultants provide assistance with:

• Features and specifications on our full line of appliances

• Installation information

• Use and maintenance procedures

• Accessory and repair parts sales

• Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.)

• Referrals to local dealers, repair parts distributors, and

service companies

Whirlpool designated service technicians are trained to fulfill the

product warranty and provide after-warranty service, anywhere in

the United States.

To locate the Whirlpool designated service company in your area,

you can also look in your telephone directory Yellow Pages.

For further assistance

If you need further assistance, you can write to Whirlpool

Corporation with any questions or concerns at:

Whirlpool Corporation

Customer Interaction Center

553 Benson Road

Benton Harbor, M149022-2692

Please include a daytime phone number in your correspondence.

Accessories U.S.A.

To order accessories, call the Whirlpool Customer Interaction

Center toll free at 1-800-442-9991 and follow the menu prompts.

Or visit our website at www.whirlpool.com and click on "Buy

Accessories Online."

WHIRLPOOL+DRYERWARRANTY

ONE YEAR FULL WARRANTY

For one year from the date of purchase, when this dryer is operated and maintained according to instructions attached to or furnished

with the product, Whirlpool Corporation will pay for FSP + replacement parts and repair labor to correct defects in materials or

workmanship. Service must be provided by a Whirlpool designated service company.

SECOND YEAR LIMITED WARRANTY ON ELECTRONIC CONTROL BOARDS

In the second year from the date of purchase, when this dryer is operated and maintained according to instructions attached to or

furnished with the product, Whirlpool Corporation will pay for FSP + replacement parts to replace the electronic control boards if

defective in materials or workmanship.

SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON PORCELAIN TOP

In the second through fifth years from the date of purchase, when this dryer is operated and maintained according to instructions

attached to or furnished with the product, Whirlpool Corporation will pay for FSP replacement parts to replace the porcelain top should

it chip or rust due to defective materials or workmanship.

Whirlpool Corporation will not pay for:

1. Service calls to correct the installation of your dryer, including venting. Heavy 4 in. (10.2 cm) metal exhaust vent must be used. Refer

to the venting section of this manual and your Installation Instructions.

2. Service calls to instruct you how to use your dryer, to replace house fuses or correct house wiring or reset circuit breakers, or to

replace owner accessible light bulbs.

3. Repairs when your dryer is used in other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, floods, acts of God, improper installation (including, but not limited

to, venting with plastic or flexible foil), installation not in accordance with local electrical and plumbing codes, or use of products not

approved by Whirlpool Corporation.

5. Replacement parts or repair labor costs for units operated outside the United States.

6. Pickup and delivery. This product is designed to be repaired in the home.

7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

8. Any labor costs incurred during the Limited Warranty periods.

WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion or limitation may not

apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Outside the 50 United States, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if another

warranty applies.

If you need service, first see "Troubleshooting." Additional help can be found by checking "Assistance or Service," or by calling our

Customer Interaction Center at 1-800-253-1301, from anywhere in the U.S.A. or write: Whirlpool Corporation, Customer Interaction

Center, 553 Benson Road, Benton Harbor, MI 49022-2692. 1/02

Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation

date for in-warranty service.

Write down the following information about your dryer to better

help you obtain assistance or service if you ever need it. You will

need to know your complete model number and serial number.

You can find this information on the model and serial number

label, located at the top inside dryer door well.

Dealer name

Address

Phone number

Model number

Serial number

Purchase date

3979274B

9/02

Printed in U.S.A.

Whirlpool GEW9200LQ0 User Manual DRYER Manuals And Guides L0409510

WHIRLPOOL Residential Dryer Manual L0409510 WHIRLPOOL Residential Dryer Owner's Manual, WHIRLPOOL Residential Dryer installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation