Whirlpool LTE6234DQ5 User Manual LAUNDRY CENTER Manuals And Guides L0604806
WHIRLPOOL Laundry Centers Manual L0604806 WHIRLPOOL Laundry Centers Owner's Manual, WHIRLPOOL Laundry Centers installation guides
User Manual: Whirlpool LTE6234DQ5 LTE6234DQ5 WHIRLPOOL LAUNDRY CENTER - Manuals and Guides View the owners manual for your WHIRLPOOL LAUNDRY CENTER #LTE6234DQ5. Home:Laundry & Garment Care Parts:Whirlpool Parts:Whirlpool LAUNDRY CENTER Manual
Open the PDF directly: View PDF .
Page Count: 16
Download | ![]() |
Open PDF In Browser | View PDF |
27"(69CM)ELECTRIC WASHER/DRYER INSTAIIATION INSTRUCTIONS Table of Contents WASHER/DRYER SAFETY.............................. 1 INSTALLATIONINSTRUCTIONS ....................2 Tools and Parts..............................................2 AlternateParts ...............................................2 LocationRequirements..................................3 Drain System.................................................. 4 Electrical Requirements.................................4 ElectricalConnection .....................................6 Venting Requirements .................................11 RemoveShipping Strap...............................12 Install Leveling Legs.....................................12 Connect the Drain Hose ..............................12 Connect the Inlet Hoses..............................13 Secure the Drain Hose.................................13 PlanVent System.........................................14 Install Vent System ......................................15 Level Washer/Dryer......................................15 Connect Vent ...............................................16 Complete Installation...................................16 WASHER/DRYER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING." These words mean: You can be killed or seriously injured if you don't immediately follow instructions. You can be killed or seriously injured if you don't follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. 8577199 INSTALLATION INSTRUCTIONS Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed: • Level • Wood block (for leveling) • Ruler or measuring tape • Knife • Vent clamps 1/4"nut driver or socket wrench (recommended) • Pliers • Scissors Wire stripper (direct wire installations) • Tin snips (for new vent installations) #2 Phillips and flat-blade screwdriver Adjustable wrench that opens to 1" (2.5 cm) or 9/16"open-end wrench (for adjusting washer/dryer feet) Caulking gun and compound (for installing new exhaust vent) Parts supplied: Remove parts package from the washer basket. Check that all parts were included. B D A. Water inlet hoses (2) B. Inlet hose flat washers (4) C. Front leveling feet with nuts (2) D. Shipping strap (Net in parts bag. See "Remove Shipping Strap. ") G E. Drain hose F. Yellow, single wire hose clamp G. Silver, double wire hose clamp Parts needed: Check local codes, electrical supply and venting, and read "Electrical Requirements" and "Venting Requirements" before purchasing parts. Mobile home installations require metal exhaust system hardware available for purchase from the dealer from whom you purchased your washer/dryer. For further information, please reference the "Assistance or Service" section of the Washer/Dryer User Instructions. Your installation may require additional parts. For ordering information, please refer to the toll free phone numbers on the front page of the Washer/Dryer User Instructions. If You Have You Will Need to Buy Laundry tub or standpipe taller than 96" (2.4 m) Sump pump system (if not already available) 1" (2.5 cm) diameter standpipe 2" (5 cm) diameter to 1" (2.5 cm) diameter standpipe adapter, Part Number 3363920 Overhead sewer Standard 20 gal. (76 L) 34" (86.4 cm) tall drain tub or utility sink and sump pump (available from local plumbing suppliers) Floor drain Siphon break, Part Number 285320, additional drain hose, Part Number 285702 and connector kit, Part Number 285442 Drain hose too short Drain hose, Part Number 285664 and connector kit, Part Number 285442 Lint clogged drain Drain protector, Part Number 367031 Water faucets beyond reach of fill hoses 2 longer water fill hoses: 6 ft (1.8 m) Part Number 76314, 10 ft (3.0 m) Part Number 350008 Washer/Dryer Dimensions 71%" (181.9 cm) Explosion Hazard Keep flammable materials and vapors, such as gasoline, away from dryer. Failure to do so can result in death, explosion, or fire. You will need • A location that allows for proper exhaust installation. See "Venting Requirements." • Aseparate • A grounded electrical outlet located within 2 ft (61 cm) of either side of the washer/dryer. See "Electrical Requirements." • A sturdy floor to support the washer/dryer weight (washed dryer, water and load) of 500 Ibs (226.8 kg). Minimum installation spacing for recessed area or closet installation • A level floor with a maximum slope of 1" (2.5 cm) under entire washer/dryer. Clothes may not tumble properly and automatic sensor cycles may not operate correctly if washer/dryer is not level. Installing on carpet is not recommended. The following dimensions shown are for the minimum spacings allowed. • Additional spacing should be considered for ease of installation and servicing. • A water heater set to deliver 120°F (49°C) water to the washer. • • Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 5-100 psi (34.5-689.6 kPa). Additional clearances might be required for wall, door and floor moldings. • Additional spacing of 1" (2.5 cm) on all sides of the washed dryer is recommended to reduce noise transfer. • For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable. • Rear clearance may be 0" (0 cm) when house exhaust system is lined up directly with dryer exhaust. 30-amp circuit. The washer/dryer must not be installed or stored in an area where it will be exposed to water and/or weather. Do not operate your washer in temperatures at or below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures. See "WashedDryer Care" in the WashedDryer User Instructions for winterizing information. Do not operate your dryer at temperatures below 45°F (7°C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. This can result in longer drying times. Check code requirements. Some codes limit, or do not permit, installation of the washer/dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector. Installation *Most installations require a minimum 51/2'' (14 cm) clearance behind the dryer for the exhaust vent with elbow. See "Venting Requirements." A B C m m 6" (7,6cm) oooO o 48in,2 10 I (310 cm21 -- - _- 06,2orn) Clearances The location must be large enough to allow the dryer door to open fully. 24 in.2 (155crn2' m o,,_27,H, (Ocm) (68.6cm) __(7.6crn) I*-o, (0cm) 3" (2.5cm) (81.3 ore) (14 cm) A. Recessed area B. Side view - closet or confined area C. Closet door with vents Mobile Home - Additional Installation Requirements This washer/dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction Safety, Title 24, HUD Part 280). Mobile home installations require: • Metal exhaust system hardware which is available for purchase from your dealer. and • Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening. The washer/dryer can be installed using the standpipe drain system (floor or wall), the laundry tub drain system, or the floor drain system. Select the drain hose installation method you need. See "Alternate Parts." Laundry tub drain system (view C) The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be at least 34" (86.4 cm) above the floor and no higher than 96" (2.4 m) from the bottom of the washer. Standpipe drain system - wall or floor (views A & B) The standpipe drain requires a minimum diameter standpipe of 2" (5 cm). The minimum carry-away capacity can be no less than 17 gal. (64 L) per minute. A 2" (5 cm) diameter to 1" (2.5 cm) diameter standpipe adapter kit is available. See "Alternate Parts." The top of the standpipe must be at least 39" (99 cm) high and no higher than 96" (2.4 m) from the bottom of the washer. Floor drain system (view D) The floor drain system requires a siphon break that may be purchased separately. See "Alternate Parts." The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer. Additional hoses might be needed. (99 cm) D It is your responsibility • To contact a qualified electrical installer. • To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition and all local codes and ordinances. A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269. • To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit. Do not have a fuse in the neutral or grounding circuit. • Do not use an extension cord. • If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate. Electrical Connection To properly install your washer/dryer, you must determine the type of electrical connection you will be using and follow the instructions provided for it here. • This dryer is manufactured ready to install with a 3-wire electrical supply connection. The neutral ground wire is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the neutral ground wire must be removed from the internal ground connector (green screw), and secured under the neutral terminal (center or white wire) of the terminal block. When the neutral ground wire is secured under the neutral terminal (center or white wire) of the terminal block, the dryer cabinet is isolated from the neutral conductor. • If local codes do not permit the connection of a neutral ground wire to the neutral wire, see "Optional 3-wire connection" section. A4-wirepowersupplyconnection mustbeusedwhenthe appliance isinstalled inalocation wheregrounding through theneutral conductor isprohibited. Grounding through the neutral isprohibited for(1)newbranch-circuit installations, (2)mobile homes, (3)recreational vehicles, and(4)areas wherelocalcodesprohibit grounding through theneutral conductors. If using a power supply cord: Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain: • A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends. • A UL listed strain relief. If your outlet looks like this: 4-wire receptacle (14-30R) Then choose a 4-wire power supply cord with ring or spade terminals and UL listed strain relief. The 4-wire power supply cord, at least 4 ft (1.22 m) long, must have four 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground conductor) may be either green or bare. The neutral conductor must be identified by a white cover. If your outlet looks like this: If connecting by direct wire: Power supply cable must match power supply (4-wire or 3-wire) and be: • Flexible armored cable or nonmetallic sheathed copper cable (with ground wire), protected with flexible metallic conduit. All current-carrying wires must be insulated. • 10-gauge solid copper wire (do not use aluminum). • At least 5 ft (1.52 m) long. GROUNDING INSTRUCTIONS [] For a grounded, cord-connected washer/dryer: This washer/dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This washer/dryer uses a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. [] For a permanently connected washer/dryer: This washer/dryer must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the washer/dryer. WARNING: Improper connection of the equipmentgrounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the washer/dryer is properly grounded. Do not modify the plug on the power supply cord: if it will not fit the outlet, have a proper outlet installed by a qualified electrician. SAVE 3-wire receptacle (10-30R) Then choose a 3-wire power supply cord with ring or spade terminals and UL listed strain relief. The 3-wire power supply cord, at least 4 ft (1.22 m) long, must have three 10-gauge copper wires and match a 3-wire receptacle of NEMA Type 10-30R. THESE INSTRUCTIONS Power Supply Cord DirectWire Fire Hazard Fire Hazard Use a new UL listed 30 amp power supply cord. Use t0 gauge solid copper Use a UL listed strain relief. Use a UL listed strain relief. Disconnect power before making Disconnect power before making electrical connections. electrical connections. Connect neutral wire (white or center wire) to center terminal (silver). Connect neutral wire (white or center wire) to center terminal (silver). Ground wire (green or bare wire) must be connected green ground connector. Connect remaining 2 terminals (gold). 1. 2. wire. Ground wire (green or bare wire) must be connected to green ground connector. to Connect remaining 2 terminals (gold). 2 supply wires to remaining 2 supply wires to remaining Securely tighten all electrical connections. Securely tighten Failure to do so can result in death, fire, or electrical shock. Failure to do so can result in death, fire, or electrical shock. Disconnect power. Remove the hold-down 3. screw and terminal block cover. A Install strain relief. Style 1: Power supply cord strain relief • B all electrical connections. Remove the screws from a 3/4"(1.9 cm) UL listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections into the hole below the terminal block opening so that one tab is pointing up and the other is pointing down, and hold in place. Tighten strain relief screws just enough to hold the two clamp sections together. C .............. _.................................... B ..........................C E A. Center, silver-colored B. Hold-down screw C. Terminal block cover D terminal block screw D. Neutral ground wire E. External ground conductor screw A. Strain relief tab pointing up B. Hole below terminal block opening C. Clamp section D. Strain relief tab pointing down Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief screws at this point. Electrical Connection Options If your home has: And you will be connecting to: Go to Section 4-wire receptacle (NEMA Type 14-30R) A UL listed, 120/240 volt 4-wire connection: Power supply cord 30-amp, dryer power supply minimum, cord* _.._ 4-wire direct A fused disconnect or 4-wire connection: Direct Wire circuit breaker box* (12.7 Style 2: Direct wire strain relief Unscrew the removable conduit connector and any screws from a 3/4"(1.9 cm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief through the hole below the terminal block opening. Reaching inside the terminal block opening, screw the removable conduit connector onto the strain relief threads. cm) 3-wire receptacle (NEMA type 10-30R) 3-wire connection: A UL listed, 120/240 volt Power supply cord 30-amp, dryer power supply minimum, cord* 3-wire direct A fused disconnect or 3-wire connection: Direct Wire box* circuit breaker *If local codes do not permit the connection of a frame-grounding conductor to the neutral wire, go to "Optional 3-wire connection" section. 4-wire connection: Power supply cord IMPORTANT: A 4-wire connection is required for all mobile homes and where local codes do not permit the use of 3-wire connections. A. Removable conduit connector B. Hole below terminal block opening C. Strain relief threads Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the direct wire cable. 4= Now complete installation following instructions for your type of electrical connection: 4-wire (recommended) 3-wire (if 4-wire is not available) C D E A. 4-wire receptacle (NEMA type 14-30R) B. 4-prong plug C. Ground prong D. Neutral prong E. Spade terminals with upturned ends E _" (1.9 cm) UL Iistedstrain relief G. Ring terminals G 1= 2. Remove center, silver-colored terminal block screw. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord under center, silvercolored terminal block screw. Tighten screw. A A. Neutral ground wire B. Center silver-colored B 4-wire connection: Direct Wire IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections. Direct wire cable must have 5 ft (1.52 m) of extra length so washer/dryer can be moved if needed. Strip 5" (12.7 cm) of outer covering from end of cable, leaving bare ground wire at 5" (12.7 cm). Cut 11/2'' (3.8 cm) from 3 remaining wires. Strip insulation back 1" (2.5 cm). Shape ends of wires into a hook shape. When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown. terminal block screw C. External ground conductor screw D. Neutral wire (white or center) E. ¾" (1.9 cm) UL Iisted strain relief 3= Connect ground wire (green or bare) of power supply cord to external ground conductor screw. Tighten screw. D C B 1= Remove center, silver-colored 2. terminal block screw. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and place the hooked end (hook facing right) of the neutral wire (white or center wire) of direct wire cable under the center screw of the terminal block. Squeeze hooked ends together. Tighten screw. .............. ................ A m B A A. External ground conductor screw B. Ground wire (green or bare) of power supply cord C. Neutral ground wire D. Center silver-colored terminal block screw c E. Neutral wire (white or center) F. 3/4"(1.9 cm) UL ilsted strain relief 4. 5. Connect the other wires to outer terminal block screws. Tighten screws. Tighten strain relief screws. 6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 7. You have completed your electrical connection. "Venting Requirements." Now go to A. Neutral ground wire B. Center silver-colored terminal block screw C. External ground conductor screw D. Neutral wire (white or center wire) E.3/4'' (1.9 cm) UL ilsted strain relief 3= Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw. C 1= 2. D B Loosen or remove center, silver-colored terminal block screw. Connect neutral wire (white or center wire) of power supply cord to the center, silver-colored terminal screw of the terminal block. Tighten screw. _E F A. External ground conductor screw B. Ground wire (green or bare) of power supply cord C. Neutral ground wire D. Center silver-colored terminal block screw A. External ground conductor screw B. Neutral ground wire C. Center silver-colored terminal block screw E. Neutral wire (white or center) F. 3/4"(1.9 cm) UL Iisted strain relief 4= Place the hooked ends of the other power supply cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws. !! !! D. Neutral wire (white or center wire) E. ¾" (1.9 cm) UL listed strain relief 3. 4. 5. 6. Connect the other wires to outer terminal block screws. Tighten screws. Tighten strain relief screws. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. You have completed your electrical connection. "Venting Requirements." Now go to 3-wire connection: Direct Wire 5. Tighten strain relief screw. 6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 7. You have completed your electrical connection. "Venting Requirements." Now go to 3-wire connection: Power supply cord Use where local codes permit connecting cabinet-ground conductor to neutral wire. Direct wire cable must have 5 ft (1.52 m) of extra length so washer/dryer can be moved if needed. Strip 31/2'' (8.9 cm) of outer covering from end of cable. Strip insulation back 1" (2.5 cm) If using 3-wire cable with ground wire, cut bare wire even with outer covering. Shape ends of wires into a hook shape. Use where local codes permit connecting cabinet-ground conductor to neutral wire. E C A. 3-wire receptacle (NEMA type 10-30R) B. 3-wire plug C. Ground prong D. Spade terminals with up turned ends E. _" (1.9 cm) UL listed strain relief F. Ring terminals G.Neutral (white or center wire) G F When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown. 1, 2. Loosen or remove center, silver-colored terminal block screw. Place the hooked end of the neutral wire (white or center wire) of direct wire cable under the center screw of terminal block (hook facing right). Squeeze hooked end together. Tighten screw. Optional 3-wire connection Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire. 1. 2. Remove center, silver-colored terminal block screw. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord/cable under center, silver-colored terminal block screw. Tighten screw. ........................... C D" A. External ground conductor screw B. Neutral ground wire C. Center silver-colored terminal block screw D, Neutral wire (white or center wire) E. _" (1.9 cm) UL listed strain relief 3, Place the hooked ends of the other power supply cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws. m !! !! A. External ground conductor screw B. Neutral ground wire C. Neutral wire (white or center wire) D, Grounding path determined by a qualified electrician E. _" (1.9 cm) UL Iisted strain relief Connect the other wires to outer terminal block screws. Tighten screws. 4. 5. Tighten strain relief screw. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 6. You have completed your electrical connection. "Venting Requirements." 10 !! !! Now go to 4. 5. Tighten strain relief screws. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 6. Connect a separate copper ground wire from the external ground conductor screw to an adequate ground. • Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor performance. • Do not install flexible metal vent in enclosed walls, ceilings or floors. Elbows 45 ° elbows provide better airflow than 90 ° elbows. J 9 Fire Hazard Use a heavy metal vent. Do not use a plastic vent. Do not use a metal foil vent. Failure to fellow or fire. these instructions can result in death Good WARNING; To reduce the risk of fire, this washer/dryer MUST BE EXHAUSTED OUTDOORS. IMPORTANT: Observe all governing codes and ordinances. The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, or a concealed space of a building. Better Clamps • Use clamps to seal all joints. • Exhaust vent must not be connected or secured with screws or other fastening devices that extend into the interior of the duct. Do not use duct tape. If using an existing vent system • Clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint. • Replace any plastic or metal foil vent with rigid or flexible heavy metal vent. • Review Vent system chart. Modify existing vent system if necessary to achieve the best drying performance. Clamp Exhaust Recommended hood styles are shown here. B If this is a new vent system Vent material • Use a heaw metal vent. Do not use plastic or metal foil vent. • 4" (10.2 cm) heavy metal exhaust vent and clamps must be used. DURASAFF Mventing products are recommended. (10.2 cm) A. Louvered hood style B. Box hood style The angled hood style (shown here) is acceptable. 4-" 4" (10.2cm) heavymetal exhaust vent DURASAFE TM vent products can be purchased from your dealer or by calling Whirlpool Parts and Accessories. For more information, see the "Assistance or Service" section of Washer/Dryer User Instructions. (10.2 c m)m_---'--_ t,,'_ 21/2(6.4- cm) • An exhaust hood should cap the vent to prevent rodents and insects from entering the home. Rigid metal vent • For best drying performance, rigid metal vents are recommended. • Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.). • • Do not use an exhaust hood with a magnetic latch. Rigid metal vent is recommended kinking. to prevent crushing and Flexible metal vent • Flexible metal vents are acceptable only if accessible for cleaning. • Flexible metal vent must be fully extended and supported when the dryer is in its final position. improper venting can cause moisture indoors, which may result in: [] Moisture damage to woodwork, wallpaper, carpets, etc. [] Housecleaning and lint to collect furniture, paint, problems and health problems. 11 Proper connection of the drain hose protects your floors from damage due to water leakage. To prevent the drain hose from coming off or leaking, it must be installed according to the following instructions: IMPORTANT: To ensure proper installation, this procedure must be followed exactly. 1. Check the drain hose to see whether it is the proper length. Excessive Weight Hazard Use two or more people to move and install washer/dryer. 2. Failure to do so can result in back or other injury. Wet the inside of the straight end of the drain hose with tap wate£ IMPORTANT: Do not use any lubricant other than water. To prevent floor damage, set washer/dryer onto cardboard before moving across floor. Move washer/dryer close to its final location. 1. Do not cut yellow strap. Pull yellow strap firmly, until completely removed from washer/dryer. There should be 2 cotter pins on the end of the shipping strap. Remove the hang tag and pin from the vent pipe. 3. Squeeze ears of the silver, double-wire clamp with pliers to open. Place clamp over the straight end of the drain hose W' (6.4 mm) from the end. _ 1/4,, 4 ram) 2. 3. Tilt the washer/dryer forward. Move each of the 2 rear legs in an up-down motion to check the self-adjusting leveling legs for free movement. This is required for proper leveling. Gently lower the washer/dryer to the floor. Cut the shipping strap about 16" (40.6 cm) from the plug end. Look for the words "CUT HERE." Discard end with cotter pins. You will use the remaining piece of shipping strap to secure the drain hose. Install the front leveling feet 1. Prop up the front of the washer/dryer about 4" (10.2 cm) with a wood block or similar object. The block needs to support the weight of the washer/dryer. 2. Screw the Iocknut onto each foot to within 1" (2.5 cm) of the base. 4. Open clamp. Twist hose back and forth while pushing onto drain connector on the side of the washer/dryer. Continue until hose contacts the ribbed stops on the cabinet. 5. Place clamp over the area marked "CLAMR" Release clamp. For laundry tub or standpipe drain systems 1. Open the yellow single-wire clamp and slide over the hooked end of the drain hose to secure the rubber and corrugated sections together. A. Hooked end B. Drain hose 1 " (2.5 cm) t 3. Screw the feet into the correct holes at the front corner of the washer/dryer until the nuts touch the washer. NOTE: Do not tighten the nuts until the washer/dryer 4. 12 2. // is level. Tilt the washer/dryer back and remove the wood block. Gently lower the washer/dryer to the floor. Put hooked end of drain hose into laundry tub or standpipe. Rotate hook to eliminate kinks. To prevent drain water from going back into the washer: • Do not straighten hooked end of the drain hose and force excess drain hose into standpipe. Hose should be secure but loose enough to provide a gap for air. • Do not lay excess hose on the bottom of the laundry tub. For use with floor drain Remove the drain hose hook from the corrugated drain hose. You may need additional parts, See Floor drain under "Alternate Parts." Insert a new flat washer (supplied) into each end of the inlet hoses. Firmly seat the washers in the couplings. A Using pliers, tighten the couplings with an additional twothirds turn. NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result. If you are working in a closet or recessed area Move the washer/dryer into its final position and remove cardboard from under washer/dryer. Remove the access panel by removing 3 Phillips-head screws and one bumper, located at the top of the access panel, Set panel, screw, and bumper aside. Complete hookup of water hoses. Replace access panel upon completion of washer/dryer installation. B A. Coupling B. Washer Connect the inlet hoses to the water faucets Make sure the washer basket is empty. 2. Attach the hose labeled hot to the hot water faucet, Screw on coupling by hand until it is seated on the washer. 3. Attach the hose labeled cold to the cold water faucet. Screw on coupling by hand until it is seated on the washer. 4. Using pliers, tighten the couplings with an additional twothirds turn. NOTE: Do not overtighten or use tape or sealants on the valve, Damage to the valves can result. Clear the water lines • Run water through both faucets and inlet hoses, into a bucket or laundry tub, drainpipe or bucket to get rid of particles in the water lines that might clog the inlet valve screens. • Check the temperature of the water to make sure that the hot water hose is connected to the hot water faucet and that the cold water hose is connected to the cold water faucet. Connect the inlet hoses to the washer 1. Attach the hot water hose to the bottom inlet valve. Attaching the hot water hose first makes it easier to tighten connection with pliers. 2. 3. Screw on coupling by hand until it is seated on the washer. Using pliers, tighten the couplings with an additional twothirds turn. Check for leaks • Turn on the water faucets and check for leaks. A small amount of water might enter the washer. You will drain this water later. NOTE: Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement dates for future reference. • If you connect only one water hose, you must cap off the remaining water inlet port. • Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found. • The apparatus must be connected to the water faucets using the new hoses. Do not use old hoses. 1. Move the washer/dryer to its final location and remove any cardboard used to move the washer/dryer. Locate the remaining ptece of shipping strap. See "Remove Shipping Strap." 2. Shipping strap Wrap the drain hose to the laundry tub leg or standpipe with the shipping strap (A or B below). Push fastener into the nearest hole in the shipping strap (see illustration above). NOTE: Do not overtighten or use tape or sealants on the valve, Damage to the valves can result. C If the water faucets and the drain standpipe are recessed, put the hooked end of the drain hose in the standpipe. Tightly wrap the shipping strap around the water inlet hoses and the drain hose (C above). Push fastener into the nearest hole in the shipping strap (see illustration above). A. Cold water inlet valve (top) B. Hot water inlet valve (bottom) 4. 5. Attach the cold water hose to the top inlet valve. Screw on coupling by hand until it is seated on the washer. 13 Alternate Choose your exhaust installation type Recommended exhaust installations Typical installations vent the dryer from the rear of the washer/ dryer. Other installations are possible. installations for close clearances Venting systems come in many varieties. Select the type best for your installation. Three close-clearance installations are shown. Refer to the manufacturer's instructions provided with the vent system. A H L '_ F A C ...................... A. Loop system with standard elbows B. Loop system with one offset and one standard elbow C. Vent system with one periscope (2" [5 cm] clearance) H A. Dryer B. Rigid metal or flexible metal vent C. Clamps D. Wall E. E G. H. Elbow Clamps Elbow Exhaust hood NOTE: The following kits for close clearance alternate installations are available for purchase. Please reference the "Assistance or Service" section of the Washer/Dryer User Instructions. • Optional exhaust installations This washer/dryer can be converted to exhaust out the right or left side. To convert the washer/dryer, use Side Exhaust Kit Part Number 279823. If your washer/dryer was previously exhausted from the right or left side, it can be converted to rear exhaust by using standard offset connections. To cover the hole in the side, one of the following plugs can be added: 692790 (white) 3977784 (biscuit) Follow the instructions in the kit to install. Kits are available from the dealer from whom you purchased your washer/dryer. Over-the-Top Installation: Part Number 4396028 Periscope Installation (For use with dryer vent to wall vent mismatch): Part Number 4396037 - 0" (0 cm) to 18" (45.72 cm) mismatch Part Number 4396011 - 18" (45.72 cm) to 29" (73.66 cm) mismatch Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm) mismatch Special provisions for mobile home installations The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside. \ B A. Standard rear offset exhaust installation B. Rear exhaust for offset close clearance connection C. Left or right side exhaust installation 14 C Determine vent path • Select the route that will provide the straightest and most direct path outdoors. 1. • Plan the installation to use the fewest number of elbows and turns. 2. • When using elbows or making turns, allow as much room as possible. • Bend vent gradually to avoid kinking. • Use the fewest 90 ° turns possible. Determine vent length and elbows needed for best drying performance • Use the Vent system chart below to determine type of vent material and hood combinations acceptable to use. 3. Properly leveling your washer/dryer vibration. Shorten the life of the dryer. • Reduce performance, resulting in longer drying times and increased energy usage. prevents excessive noise and 1. Check the levelness of the washer/dryer by placing a level on the top edge of the washer, first side to side, then front to back. 2. If the washer/dryer is not level, prop up the front with the wood block and adjust the feet up or down as necessary. Remove wood block. 3. Tilt the washer/dryer forward until the rear of the washer/dryer is at least 4" (10.2 cm) off the floor. You may hear the selfadjusting rear feet click into place. Lower the washer/dryer to the floor. Check the levelness of the washer/dryer with a level as shown above. NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust systems longer than those specified will: • Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp. Run vent to dryer location. Use the straightest path possible. See "Determine vent length" in "Plan Vent System." Avoid 90 ° turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the interior of the vent to secure vent. The Vent system chart provides venting requirements that will help to achieve the best drying performance. Vent system chart NOTE: Side exhaust installations add a 90 ° turn inside the dryer. To determine maximum exhaust length, add one 90 ° turn to the chart. Number of 90 ° turns or elbows Type of Vent Box or Louvered hoods Angled hoods 0 Rigid metal Flexible metal 37 ft (11.3 m) 25 ft (7.6 m) 35 ft (10.7 m) 20 ft (6.1 m) 1 Rigid metal Flexible metal 32 ft (9.7 m) 21 ft (6.4 m) 27 ft (8.2 m) 16 ft (4.9 m) 2 Rigid metal Flexible metal 24 ft (7.3 m) 15 ft (4.6 m) 19 ft (5.8 m) 10 ft (3.0 m) If washer/dryer will not level, recheck rear leveling legs for free movement as described in the "Install Leveling Legs" section. Repeat until the washer/dryer is level. NOTE: It may be necessary to level the washer/dryer after it is moved into its final position. 4. again After the washer/dryer is in the final location and is level, use an adjustable or open-end wrench to turn the nuts on the front feet tightly against the washer cabinet. If the nuts are not tight against the washer cabinet, the washer/dryer may vibrate. 15 1. 2. 1. 2. 3. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in washer/dryer. If connecting to existing vent, make sure the vent is clean. The vent must fit over the exhaust outlet and inside the exhaust hood. Make sure the vent is secured to exhaust hood with a 4" (10.2 cm) clamp. Move washer/dryer into its final position. Do not crush or kink vent. Make sure washer/dryer is level. ......... Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. Check that you have all of your tools. Dispose of/recycle all packaging materials. Keep the plastic foam for use if the washer/dryer should be transported. 4. Check the washer/dryer's crushed or kinked. 5. Check that the washer/dryer is level and front leveling feet are tight. See "Level Washer/Dryer." For power supply cord installations, plug into an outlet. For direct wire installation, turn on power. Check that the water faucets are on. Check for leaks around faucets and inlet hoses. 6. 7. 8. 9. final location. Be sure the vent is not Remove the blue protective film on the console and any tape remaining on the washer/dryer. 10. Read the Washer/Dryer User Instructions. 11. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust. 12. To test the washer, measure r/2the normal recommended amount of detergent and pour it into the washer. Close the lid. Select the REGULAR cycle and pull out the Cycle Control knob. Allow the washer to complete one whole cycle. 13. To test the dryer, set the dryer on a full heat cycle (not an air cycle) for 20 minutes and start the dryer. If the dryer will not start, check the following: • Controls are set in a running or "On" position. • Start button has been firmly pushed. • Washer/dryer is plugged into a grounded outlet and/or electrical supply is on. • Household fuse is intact and tight, or circuit breaker has not tripped. • Dryer door is closed. 14. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you do not feel heat, turn off the dryer and check the following: • There may be 2 household fuses or circuit breakers for the dryer. Check to make sure both fuses are intact and tight, or that both circuit breakers have not tripped. If there is still no heat, contact a qualified technician. NOTE: You may notice a burning odor when dryer is first heated. This odor is common when the heating element is first used. The odor will go away. 8577199 (c) 2005. All rights reserved. Benton Harbor, Michigan 49022 TM DURASAFE is a trademark of Whirlpool, U.S.A. 8/05 Printed in U.S.A.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 16 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 3, 2, 1, 4 Create Date : Fri Apr 20 14:24:39 2007 Author : Title : Subject :EXIF Metadata provided by EXIF.tools