Wild Planet Entertainment EPSYS11324TX2 RC Toy User Manual

Download:
Mirror Download [FCC.gov]
Document ID	406945
Application ID	LapHRtGBqhcayiVHFdSKTw==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	10.52kB (131467 bits)
Date Submitted	2004-03-20 00:00:00
Date Available	2004-03-20 00:00:00
Creation Date	2004-03-16 10:56:44
Document Lastmod	2004-03-16 11:16:31
Document Title	User Manual
Document Creator	HP 9100C Digital Sender
Document Author:	ITS ELECTRIC TOY

Explorer's Positioning System“
Agessand Up
11324
Hand—held tracking system
Track movement up to 75 feet lZZmi!
Important: Please save this instruction sheet.
It contains valuable product information.
Battery Safety Information:
¥ Requires eight AAA (LR3i batteries lnot included).
v W e recommend you use alkaline batteries. Rechargeable batteries may
affect perforrmnce.
u o nly aduhs should install and replace batteries
¥ Do not recharge non-rechargeable batteries.
96 Remove dead or exhausted batteries.
¥ Insert batteries correctly. Match positive and negative symbols.
¥ Do not place anything across the battery terminals.
¥ Only use the batteries specified above.
¥ Do not mix alkaline, standard lcarbon-zinc), or rechargeable
lnickel-cadtniutn or NiMHi batteries.
¥ Do not mix old and new batteries.
¥ Do not dispose of batteries in a fire; they may explode.
¥ Dispose of batteries safely, recyclethem where possible.
Attention Adults -- T 0 Replace Batteries
Explorer's Positioning System“ requires two AAA (LR3i batteries for each
sensor and two AAA (LRS) batteries for the base station, making eight
AAA (LR3) batteries in total lnot included).
To Install Batteries In The Base Station
1. Locate the battery compartment on the bottom ofthe base station.
Use a small Phillips head screwdriver to loosen the screw, and unclip the
battery cover. (fig A).
2. Place batteries in compartment as shown.
3. Replace battery cover and tigtten screw.
T 0 Install Batteries In Each Sensor
1. Locate the screw on the base ofthe sensor. Use a small Phillips head
screwdriver to loosen the screw and trnclipthe battery cover,
2. Place batteries in compartment as shown trig B).
3, Replace battery cover and tig1ten screw.
4. Repeat for each sensor.
To Set Sensors
I. Unwind the A ntenna from around each sensor and straigrten upwards,
2. Slide each sensor's switch to the 0 N position (fig ii.
3. Place each or the sensors in a hiring place anywhere up to 75 feet (22m)
from the base staion.
N or E: Be sure to set the sensor lens ocing away from any obstructions
(walls, books etc).
T 0 Track the Action!
1. Flipopen the Map C over,
2. Slide the A udio / Mute / Off switch to mute or audio position
(fig 2), The Map G rid will illuminate.
3. Make sure the antenna on the hand held unit is as straight as possible.
4. Use the Dry Erase Market to draw a plan on the mapgid
showing where the sensors are set.
Tip: Draw a line from each sensors LED to its position on the ptan.
S. W hen someone moves in front of Liglt sensorlsensot 2) or moves
the Vibrator (sensor ii with the Audio /Mule/0fl swrtch in A udio
position, the base station will announce which sensor has been tripped
and the sensor's LED will flash.
Map cover
manna Reusable map gid
Early warning LEDs
Sensors
Sensor
$Button
Dry Erase Marker Audio/Mme/Ofiswitch
rrgl figZ
Leave N o T race!
I. Slide the Audio lMUte lOffswitch to the "0 FF" position
2. Collect each sensor and Wrap its antenna around the sensor body.
3. W ipe offthe map gid with aclean dry paper towel.
Troubleshooting
¥ Before settingthe sensors, move your hand in front ofthe lens. lithe LED
on the base station does not flash, check the antenna and / or batteries.
34 Check that nothingis blockingthe sensor lens. The sensors will only
detect movement five feet directly in front of the lens.
5. w hen someone moves in front ofa sensor with the Audio / Mute/oft o Make me m a" [he amen,“ me m as mm 35 possum
switch in Mute position, there will be no audio warning but the
sensor's LED will flash.
pa earn A
it ’
Jib m
[xfioter‘s pastrar-ngswenn ”3214000
r out 1475570
www wIIDPLAMET com
worn w 4 mm for the
CHOKlNG HAZARD: Small Parts.
Not for Children Under 3 Years.
momma... as...
WARNING“ ..o...a.a..s...s..et.,,ea...,
- ...mama..,....a.,,.t,a...m...a
......s.............t......a.ahm...
was...”
......W..awa....,.s.w.sts
a............a.......

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Creator                         : HP 9100C Digital Sender
Create Date                     : 2004:03:16 10:56:44
Author                          : ITS ELECTRIC TOY
Producer                        : 
Title                           : 
Subject                         : manual
Modify Date                     : 2004:03:16 11:16:31+08:00
Page Count                      : 1

EXIF Metadata provided by EXIF.tools