Wilson Electronics 2B1225 DUAL-BAND BI-DIRECTIONAL CELLULAR AMPLIFIER User Manual
Wilson Electronics, LLC DUAL-BAND BI-DIRECTIONAL CELLULAR AMPLIFIER Users Manual
Users Manual
Signal Booster
Installation
Guide
Contents
Before Getting Started ............................1
Accessories and Antenna Options . . . . . . . . . . . . . . . . . . 1
Quick Installation Overview ........................2
Installation Diagram ..............................2
Installing a Wilson Electronics External Adapter ........3
Installing Outside Antenna .........................3
Installing the Signal Booster . . . . . . . . . . . . . . . . . . . . . . . 3
Powering Up a Wilson Electronics Signal Booster . . . . . . 4
Installing Mounting Plate on DataPro Signal Booster . . . . 4
Warnings and Recommendations ...................5
Guarantee and Warranty ..................Back Cover
Signal Booster Specifications . . . . . . . . . . . . . .Back Cover
DataPro™
Dual-Band
Signal Booster
Note: This manual contains important safety and operating information.
Please read and follow the instructions in this manual. Failure to do so could
be hazardous and result in damage to your signal booster.
1Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: tech@wilsonelectronics.com Hours: 7 am to 6 pm MST.
2
Inside this Package
Accessories & Antenna Options
Before Getting Started
This guide will help you properly install your Wilson Electronics Signal Booster. It is impor-
tant to read through all of the installation steps for your particular application prior to
installing any equipment. Read through the instructions, visualize where all the equipment
will need to be installed and do a soft installation before mounting any equipment. For further
assistance please call our Wilson Electronics Technical Support Team: 866-294-1660.
Installation Instructions for the Following Wilson Electronics
Signal Boosters:
DataPro: FCC ID: PWO2B1225 IC: 4726A-2B1225 Model: 2B1225
The term “IC” before the radio certification number only signifies that Industry Canada
technical specifications were met.
NMO
Mount
Dual-Band
(301104)
Magnet
Mount
Dual-Band
(301125)
Trucker
Mount
Dual-Band
(301101)
Mini
Magnet
Dual-Band
(301126)
Adapters may be required
Adapters may be required
Adapters may be required
800/1900
MHz Omni-
Directional
Antenna
(301201)
Mounting Plate
(901138)
Lightning
Surge Protector
(859902)
Marine
Antenna
Dual-Band
(301130)
800 MHz Yagi Cellular Antenna (301111)
Yagi Antennas Omni Directional Antennas
Accessories
1900 MHz Yagi PCS Antenna (301124)
800 MHz Yagi Cellular Antenna (301129)
5V Power
Supply
DataPro
Signal
Booster
6’ RG174
cable
Accessories packaged may not exactly match the below photos due to upgrades
1
2
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: tech@wilsonelectronics.com Hours: 7 am to 6 pm MST.
Select a location to install the signal booster that is away from excessive heat, direct 1.
sunlight, moisture and that has proper ventilation. Do not place the signal booster in
an air-tight enclosure.
Select a location on the top of the structure to install the outside antenna. Use a cell phone 2.
in test mode to find the strongest signal from the cell tower.
Visit
www.WilsonElectronics.com to find test mode function for your particular cell phone.
Run the outside antenna cable to the signal booster and attach it to the connector 3.
labeled “outside antenna.”
An external adapter is required to connect the cell phone or cellular data card to the 4.
signal booster. The external adapter plugs into the included antenna extension cable
and directly into a socket on the cell phone or cellular data card. Run the extension
cable from the external adapter and attach it to the connector labeled “cellular phone
or data card” on the signal booster.
Note: Be careful when plugging the connector in so as not to bend the center pins on
the connectors. Ensure all cables have a tight connection.
Before powering up the signal booster verify that both the outside antenna and the 5.
inside antenna are connected and check that all connections are tight. An AC surge
protector is recommended for all installations.
Quick Installation Overview
The following steps provide a summary of the signal booster/antenna installation process.
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660.
Cellular
Modem
Power
Supply
Antenna
Signal
Booster
Installation Diagram
(Figure 1)
AC Surge
Protector
3Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: tech@wilsonelectronics.com Hours: 7 am to 6 pm MST.
4
How it Works
Wilson Electronics signal boosters are bi-directional devices that deliver service levels
consistent with what would be expected in areas of high cell network coverage. They
amplify a weak or shadowed signal in mobile, marine and in-building applications.
When using a Wilson Electronics signal booster in conjunction with Wilson Electronics
antennas, the outside antenna will collect the cell tower signal and send it through the
cable to the signal booster. Cell phones and cellular data cards then communicate with the
improved signal. When a cell phone or cellular data card transmits, the signal is amplified
by the signal booster and broadcast back to the cell tower through the outside antenna.
Installing a Wilson External Adapter
An external adapter is required to connect the cell phone or cellular data card to the signal
booster. The external adapter is cell phone/data card-specic and may be purchased
through a local retailer. Refer to Wilson Electronics Adapter Guide to identify the correct
adapter for your cell phone or cellular data card. The adapter guide is available through a
local retailer or at www.WilsonElectronics.com. The external adapter plugs into the antenna
extension cable (included) and directly into a socket on the cell phone or cellular data card.
The external adapter and the extension cable are long enough to reach the signal booster
location. This allows for ease and convenience of use. Run the extension cable from the
external adapter and attach it to the connector labeled “cellular phone or data card” on the
signal booster.
NOTE: Depending on your specific cell phone, the adapter socket may be located beneath
a rubber plug.
Installing a Wilson Outside Antenna
Select a location on the top of the structure to install the outside antenna that has the most
unobstructed line of sight to the cell tower. To obtain maximum performance, the antenna
should point toward the cell tower. Follow the instructions included with the outside
antenna and the RF Safety Warning (page 5).
Lightning protection is recommended for all stationary installations.
Take extreme care to ensure neither you nor the antenna come in contact with any electrical
power lines.
Ensure there are at least three feet of clearance in all directions surrounding the antenna.
Installing a Wilson Electronics Signal Booster
Select a location to install the signal booster that is away from excessive heat, direct 1.
sunlight, moisture and that has proper ventilation. Ensure the signal booster is
installed within six feet of where the cell phone or cellular data card will be used (to
accommodate the six-foot adapter extension cable).
Run the cable from the outside antenna and attach it to the connector labeled “outside 2.
antenna” on the signal booster.
3
4
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: tech@wilsonelectronics.com Hours: 7 am to 6 pm MST.
Powering up a Wilson Electronics Signal Booster
Ensure that both the outside antenna coax cable and the adapter coax cable are con-1.
nected to the signal booster before powering up the signal booster.
Connect the power supply to the power input labeled with the USB symbol on the 2.
signal booster. Plug the power supply into a wall outlet.
The indicator light on the top of the signal booster will be GREEN when the unit is pow-3.
ered up and working properly.
If the light is off, ensure power supply connections are tight.4.
Carefully insert the
power cable.
Warning: Use only a Wilson Electronics
power supply. Use of a non-Wilson
Electronics product could damage your
equipment.
!
Warning: Verify that both the outside
antenna and the adapter extension cable
are connected to the signal booster before
powering up the signal booster.
!
Testing a Wilson Electronics Signal Booster
To test your signal booster, go to a weak signal area where your cell phone registers only
1-2 bars without the signal booster turned on. Then, connect the signal booster to the
phone and you should see a signal improvement of 2 or more bars. Note: Many phones
take up to 30 seconds to reset the bar indicator.
Installing the Mounting Plate on DataPro™ Signal Booster (optional)
To purchase a mounting plate call Wilson Electronics Sales Team 800-204-4104.
Remove two screws from back of
signal booster that correspond with the
mounting plate.
Place signal booster on mounting plate
and reinstall the two screws previously
removed from back of signal booster.
Caution: Do not remove “Void Sticker.”
5Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: tech@wilsonelectronics.com Hours: 7 am to 6 pm MST.
6
Warnings and Recommendations
Warning: Verify that both the outside antenna and the adapter extension cable are
connected to the signal booster before powering up the signal booster.
Warning: Use only the power supply provided in this package. Use of a non-WIlson
Electronics products may damage your equipment.
Warning: RF Safety: All omni-directional antennas shown on page 1 must be
installed so that the distance from the antenna to any person is no less
than 8 inches. All Yagi antennas shown on page 1 must be installed
so that the distance from the antenna to any person is no less than 26
inches. Yagi antennas may not be used indoors or in a mobile installation.
Please contact Wilson Electronics Technical Support Team for safe
distances from other antennas.
Lightning protection is recommended for all in-building installations.
It is recommended to verify that outside antenna installations comply with relevant electrical
codes (e.g. National Electrical Code).
NOTE: The aluminum casing of a Wilson Electronics signal booster will adjust very quickly
to the ambient temperature of its environment. For example, in the summer, when the
inside of a car can reach 140 degrees Fahrenheit, the signal booster temperature may be
150 degrees or higher. The casing will be hot to the touch, similar to a metal door handle or
a steering wheel. Such high temperatures will not damage the signal booster, nor do they
pose a fire risk to the structure. As recommended in these instructions, install the signal
booster in a location with adequate ventilation. Keep the area free of items that could block
air flow to the signal booster. Do not install the signal booster in direct sunlight.
Mobile Installation In-Building Installation
Outside
Antenna
Outside
Antenna
(Point towards
cell tower)
Signal Booster
Signal
Booster
DC Power Supply
Power
Supply
Connect to
cell phone or
data card
Connect to
cell phone or
data card
This is the recommended install for in-vehicle
use. Contact our Technical Support Team for
more information at: 866-294-1660 or tech@
wilsonelectronics.com
This is the recommended install for in-building
use. Contact our Technical Support Team for
more information at: 866-294-1660 or tech@
wilsonelectronics.com
AC Surge
Protector
Lightning
Surge
Protector
5
6
Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660
or email: tech@wilsonelectronics.com Hours: 7 am to 6 pm MST.
Operation is subject to the following two conditions: (1) This device may not cause interfer-
ence and (2) this device must accept any interference, including interference that may cause
undesired operation of this device.
About Wilson Electronics
Wilson Electronics, Inc. has been a leader in the wireless communications industry for over
40 years. The company designs and manufactures signal boosters, antennas and related
components that significantly improve cellular telephone signal reception and transmission
in a wide variety of applications, mobile, in-building, and M2M.
With extensive experience in antenna and signal booster research and design, the
company’s engineering team uses a state-of-the-art testing laboratory, including an
anechoic chamber and network analyzers, to fine-tune antenna designs and performance.
For its signal boosters, Wilson Electronics uses a double electrically insulated RF
enclosure and cell tower simulators for compliance testing.
Wilson Electronics signal boosters feature patented Smart Technology™ that enables
them to automatically adjust their power based on cell tower requirements. By detecting
and preventing oscillation feedback, signal overload and interference with other users,
these Smart Technology™ signal boosters improve network cell phone areas without
compromising carrier systems.
All products are engineered and assembled in the company’s 55,000-square-foot
headquarters in St. George, Utah. Wilson Electronics has product dealers in all 50 states
as well as in countries around the world.
Disclaimer: The information provided by Wilson Electronics, Inc. is believed to
be complete and accurate. However, no responsibility is assumed by Wilson
Electronics, Inc. for any business or personal losses arising from its use, or for any
infringements of patents or other rights of third parties that may result from its use.
Copyright © 2011 Wilson Electronics, Inc. All rights reserved.
One or more of the following U.S. Patent numbers may apply to the Signal Booster in this
product – D596,614; D596,615; D563,381;7,729,669; 7,486,929; 7,729,656; 7,409,186;
7,783,318; 7,684,838; 12,714,994.
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson Electronic’s 30-day money-back guarantee. If
for any reason the performance of any product is not acceptable, simply return the product directly to the
reseller with a dated proof of purchase.
1-Year Warranty
Wilson Electronics signal boosters are warranted for one (1) year against defects in workmanship and/
or materials. Warranty cases may be resolved by returning the product directly to the reseller with a
dated proof of purchase.
Signal boosters may also be returned directly to the manufacturer at the consumer’s expense, with
a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by Wilson
Electronics. Wilson Electronics shall, at its option, either repair or replace the product. Wilson Electronics
will pay for delivery of the repaired or replaced product back to the original consumer if located within
the continental U.S.
This warranty does not apply to any signal boosters determined by Wilson Electronics to have been
subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic
properties.
RMA numbers may be obtained by phoning Technical Support at 866-294-1660.
AIG #110867 (811225) - Rev1 - 022511
3301 East Deseret Drive, St. George, UT 84790
For additional Technical Support visit www.WilsonElectronics.com
or email at: tech@wilsonelectronics.com
Phone: 866-294-1660 Local: 435-673-5021 Fax: 435-656-2432
www.twitter.com/WilsonCellular www.facebook.com/WilsonCellular
Signal Booster Specifications
Dual Band
800/1900 MHz Specifications
Model Number / Part Number 2B1225
Connectors SMA Female
Impedance (input/output) 50 ohms
Dimensions
with mounting plate 3.9 x 3.1 x 0.95 in
without mounting plate 3.9 x 1.9 x .085 in
Frequency 824-894 MHz / 1850-1990 MHz
1Passband Gain (nominal)
Factory set: 5 dB minimum to 20 dB maximum
220 dB Bandwidth (nominal)
800 MHz 30 MHz
1900 MHz 68 MHz
Power output for single cell phone (uplink) 800 MHz 1900 MHz
CDMA 30.0 dBm 32.7 dBm
GSM 29.4 dBm 29.0 dBm
EDGE 28.3 dBm 28.9 dBm
WCDMA 31.5 dBm 32.4 dBm
Power output for single received channel (downlink) 800 MHz 1900 MHz
CDMA -3.2 dBm 1.5 dBm
GSM -2.4 dBm -1.5 dBm
EDGE -3.3 dBm -1.5 dBm
WCDMA -3.8 dBm -2.0 dBm
3,4Power output for multiple
received channels (downlink). The
maximum power is reduced by the
number of channels:
Number of
channels
Maximum Power3
800 MHz 1900 MHz
2 -10.9 dBm -5.2 dBm
3 -14.4 dBm -8.8 dBm
4 -16.9 dBm -11.3 dBm
5 -18.9 dBm -13.2 dBm
6 -20.5 dBm -14.8 dBm
Noise Figure (typical) 3 dB nominal
Isolation > 60 dB
Power Requirements 5V DC, 1A
Notes:
1. Nominal gain is the maximum gain at any frequency in the passband.
2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB
lower than the passband amplification. One of the frequencies is lower than the passband and the other is higher.
3. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier
signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can
cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by
an attenuator at the output of the device.
4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.