Wilson Electronics 460002 Model 460002 Signal Booster User Manual Rev 2

Wilson Electronics, LLC Model 460002 Signal Booster Rev 2

UserManual.wiki >

Wilson Electronics >

460002 User Manual >

User Manual Rev 2

Contents

1. User Manual Rev 1
2. User Manual Rev 2

User Manual Rev 2

2Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660Or email: tech@wilsonelectronics.com Mon.- Fri. Hours: 7am to 6 pm MST.Warning: In a wireless installation, do not plug the Signal Booster directly into the cell phone and/or data card using an antenna adapter. It may damage the Signal Booster, cell phone and/or data card.!!Quick Installation OverviewMagnet - Mount Antenna ShownPart #301103CarefullyPull DownDoor SealRun CableUnder SealTuck CableUnder SealInstalling the Outside AntennaTo receive the best cell signal, select a location in the center of the vehicle’s roof 12 inches away from any other antennas or windows. If the vehicle has a sunroof, it is important to separate the Inside and Outside Antennas by at least five feet. This prevents the Signal Booster from overloading or oscillating. As shown above. Follow the specific antenna installation instructions included with the Outside Antenna.Separation of the Inside and Outside Antennas is very important. The metal roof of the vehicle acts as a barrier and helps shield the two antennas from each other, preventing oscillation (feedback).The Outside Antenna must be installed vertically. Signal performance will be degraded if the antenna is not vertical.The antenna cable may run through the door to the Signal Booster.For a more professional looking installation, run the antenna cable under the door seal. The antenna cable is small enough to easily tuck under the door seal or plastic molding. Carefully pull down the door seal. Run the cable through the seal and push the seal back into place. This prevents constant wear and tear on the cable as the door opens and closes.Warning: Do not plug in the DC power supply until the Outside and Inside Antenna cables are attached to the Signal Booster.HUMMERHUMMERInstallation DiagramOutsideAntennaInsideAntennaDistance between antennas through a sunroof must be 5 feet or more.DC Power SupplySignal BoosterCell PhonePDANotebookBefore Getting StartedThis guide will help you properly install your Wilson Electronics Dual-Band Mobile Wireless Signal Booster. It is important to read through all of the installation steps for your particular application prior to installing any equipment. Read through the instructions, visualize where all the equipment will need to be installed and do a soft installation before mounting any equipment. Contact Wilson Electronics Technical Support Team with any questions at 866-294-1660.

4Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660Or email: tech@wilsonelectronics.com Mon.- Fri. Hours: 7am to 6 pm MST.Lights and Troubleshooting for Mobile BoostersNote: The power light will turn green when the Signal Booster is successfully powered up. When the 800 MHz or 1900 MHz lights are lit green, the Signal Booster is amplifying the outside signal.Green: If the indicator lights on the Signal Booster are green, the unit is powered up and working properly. Red: If one or more lights on the Signal Booster are red, this indicates that the Signal Booster has shut down on that frequency to prevent an oscillation (feedback). First, make sure that all connections are tight. The Outside Antenna needs to be moved farther from the Inside Antenna. Move the Outside Antenna on the roof of the car to the rear of the car, but at least 8-12 inches from the rear or side windows. Reset the Signal Booster by disconnecting then reconnecting the power to the Signal Booster. Blinking Red: If one or more of the lights on the Signal Booster are blinking red, this means that the Signal Booster has shutoff due to close proximity to the handset or mobile device. Increase the distance between the handset and the Inside Antenna until the light is no longer flashing red. Contact Wilson Electronics Technical Support Team for assistance.Understanding the Signal Booster LightsAll green lights: Signal Booster is working properlySolid Red Light: Signal Booster has shut down on that frequency Blinking Red: Signal Booster has shutoff

5 6Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660Or email: tech@wilsonelectronics.com Mon.- Fri. Hours: 7am to 6 pm MST.This device complies with Part 15 of FCC rules. Operation is subject to two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modications not expressly approved by Wilson Electronics could void the authority to operate this equipment.Each Signal Booster is individually tested and factory set to ensure FCC compliance. The Signal Booster cannot be adjusted without factory reprogramming or disabling the hardware. The Signal Booster will amplify, but not alter the incoming and outgoing signals in order to increase coverage of authorized frequency bands only. If the Signal Booster is not in use for ve minutes, it will reduce gain until a signal is detected. If a detected signal is too high in a frequency band, or if the Signal Booster detects and oscillation, the Signal Booster will automatically turn the power off on that band. For a detected oscillation the Signal Booster will automatically resume normal operation after a minimum of 1 minute. After 5 (ve) such restarts, any problematic bands are permanently shut off until the Signal Booster has been manually restarted by momentarily removing the power from the Signal Booster. Noise power, gain, and linearity are maintained by the Signal Booster’s microprocessor. Warnings and Recommendations Warning: In a wireless installation, do not plug the Signal Booster directly into the cell phone or cellular data card using an antenna adapter. It will damage the Signal Booster, cell phone or cellular data card. Warning: Do not plug in the DC power supply until the Outside and Inside Antenna cables are attached to the Signal Booster. Warning: The Inside Antennas must have a 1.5 feet of separation distance from all active users. Warning: RF Safety: Any antenna used with this device must be located at least 8 inches from all persons. Warning: Use only the power supply provided in this package. The power supply must be 6 V DC Output.BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider.You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person.You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider.WARNING. E911 location information may not be provided or may be inaccurate for calls served by using this device.This is a CONSUMER device.

6Contact Wilson Electronics’s Technical Support Team with any questions at 866-294-1660Or email: tech@wilsonelectronics.com Mon.- Fri. Hours: 7am to 6 pm MST.30-Day Money-Back GuaranteeAll Wilson Electronics products are protected by Wilson Electronics 30-day money-back guarantee. If for any reason the performance of any product is not acceptable, simply return the product directly to the reseller with a dated proof of purchase.2-Year WarrantyWilson Electronics Signal Boosters are warranted for two (2) years against defects in workmanship and/or materials. Warranty cases may be resolved by returning the product directly to the reseller with a dated proof of purchase. Signal Boosters may also be returned directly to the manufacturer at the consumer’s expense, with a dated proof of purchase and a Returned Material Authorization (RMA) number supplied by Wilson Electronics. Wilson Electronics shall, at its option, either repair or replace the product. Wilson Electronics will pay for delivery of the repaired or replaced product back to the original consumer within the continental U.S..This warranty does not apply to any Signal Boosters determined by Wilson Electronics to have been subjected to misuse, abuse, neglect, or mishandling that alters or damages physical or electronic properties.RMA numbers may be obtained by contacting Technical Support at 866-294-1660.Disclaimer: The information provided by Wilson Electronics, LLC is believed to be complete and accurate. However, no responsibility is assumed by Wilson Electronics, LLC for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use.U.S. Patent Nos. – 7,221,967; 7,729,669; 7,486,929; 7,409,186; 7,783,318; 8,583,034; 8,583,033; D565,021Copyright © 2014 Wilson Electronics, LLC. All rights reserved.About Wilson ElectronicsWilson Electronics, LLC has been a leader in the wireless communications industry for over 40 years. The company designs and manufactures Signal Boosters, antennas and related components that significantly improve cellular phone signal reception and transmission in a wide variety of applications, mobile (vehicle, RV, marine) and in-building (home, office, machine to machine).With extensive experience in antenna and Signal Booster research and design, the company’s engineering team uses a state-of-the-art testing laboratory, including an anechoic chamber and network analyzers, to fine-tune antenna designs and performance. For its Signal Boosters, Wilson Electronics uses a double electrically shielded RF enclosure and cell tower simulators for compliance testing.Wilson Electronics Signal Boosters feature patent-pending Smart Technology ™ that enables them to automatically adjust their power based on cell tower requirements. By detecting and preventing oscillation (feedback), signal overload and interference with other users, these Smart Technology ™ Signal Boosters improve network cell phone areas without compromising carrier systems.All products are engineered and assembled in the company’s 100,000 square-foot headquarters in St. George, Utah. Wilson Electronics has product dealers in all 50 states as well as in countries around the world.

Signal Booster SpecificationsDual Band SpecificationsModel Number 460002Connectors FMEImpedance (input/output) 50 ohmsDimensions 5.6 x 3.6 x 1.7 inch or 14.2 x 9.1 x 4.4 cmWeight 1.2 lbs or 0.54 kgFrequency 824-894 MHz / 1850-1990 MHz1Passband Gain (nominal) 800 MHz 1900 MHz47.8 dB 43.8 dB220 dB Bandwidth (nominal) Typical Maximum800 MHz (uplink/downlink) 41.1 42.91900 MHz (uplink/downlink) 76.1 76.5Power output for single cell phone (uplink) dBm 800 MHz 1900 MHz23.4 23.4Power output for single cell phone (downlink) dBm 800 MHz 1900 MHz-3.1 -0.93Power output (uplink) for multiple cell phones: No. TonesMaximum Power800 MHz 1900 MHz2 23.3 18.03 19.8 14.54 17.3 12.05 15.3 10.16 13.7 8.54Power output for multiple received channels (downlink). No. TonesMaximum Power800 MHz 1900 MHz2 -1.4 2.53 -4.9 -1.04 -7.9 -3.55 -9.3 -5.46 -10.9 -7.0Noise Figure (typical) 3 dB nominalIsolation > 90 dBPower RequirementsSignal Booster Usage 6 V, 0.5 A - 1.5 A (subject to uplink power)The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device.111256_Rev01_01.16.14

Navigation menu