Wilson Electronics 8011SB In-Building Wireless Cellular SmartTech Amplifier User Manual

Wilson Electronics, LLC In-Building Wireless Cellular SmartTech Amplifier Users Manual

Users Manual

Wilson Electronics, Inc.3301 E. Deseret Drive, St. George, Utah 84790For additional technical support go towww.wilsonelectronics.comPhone: 1-866-294-1660 Fax: 1-435-656-2432IN-BUILDINGWirelessThe term “IC:” before the radio certification number only signifiesthat Industry of Canada technical specifications were met.Cellular & iDEN AmplifierInstallation GuideCellular & iDENAnalog & Digital - CDMA, GPRS, GSM, TDMAIn-Building Wireless Cellular Smart TechnologyTM Amplier824-894 MHzFCC ID:PWO8011SBIC: 4726A-8011SBIn-Building Wireless iDEN Smart TechnologyTM Amplier806-866 MHzFCC ID:PWO8040SBIC: 4726A-8040SB
231. PURPOSE OF THE AMPLIFIERThe Smart TechnologyTM Ampliers improve RF coverage for areas in which low signal strength is a problem.2. PACKAGE CONTENTS 2.1 Amplier 2.2 AC-to-DC (110 volt) Power Supply3. HOW THE AMPLIFIER FUNCTIONSThe signal is received by the outside antenna from the cell site. The signal is then AMPLIFIED and transmitted to your phone through the inside antenna. When the phone transmits, the signal is received by the inside antenna and then AMPLIFIED and transmitted to the cell site through the outside antenna.4. AMPLIFIER INSTALLATION (see illustration on pg. 4 & 5)4.1 Installing the Wilson Cellular Outside Antenna4.1.1 Select a location on the roof using your phone in test mode to nd the best signal strength. (See leaet titled PHONE TEST MODES)4.1.2 The Outside Antenna should be located in an area with at least a 3’ radius clear of obstructions and other radiating elements. NOTE: Mount the AMPLIFIER away from direct sunlight, excessive heat and/or moisture. The amplifier needs proper ventilation. DO NOT place the amplifier in an air-tight enclosure.WARNING: The outside antenna used with this amplier must be xed-mounted on an outdoor permanent structure with a separation of at least 20 feet from all persons during normal operation.4.2 Installing The AmplierWARNING: Connecting amplier directly to cell phone may damage phone.WARNING: Connect both antennas before connecting power to the amplier.4.2.1 Mount the AMPLIFIER on a wall or ceiling using #6 screws.4.2.2 Connect Outside Antenna to the AMPLIFIER side labeled “OUTSIDE ANTENNA”.4.2.3 Connect Inside Antenna to the AMPLIFIER side labeled “INSIDE ANTENNA”.4.2.4 Verify that both the OUTSIDE and INSIDE antennas are connected before connecting the AC-DC power supply to the power outlet.4.4 Installing The Wilson Cellular Inside Antenna4.4.1 See antenna packaging for model specic instructions.4.4.2 The Inside Antenna should be centered in the weak signal area. The INSIDE AN-TENNA should be at least 7’ from the oor.WARNING: The inside antenna used with this amplier must have a separation dis-tance from all persons that is at least: 9 inches for the 2.5 dBi Dome antenna. 14 inches for the 7 dBi Panel antenna.The amplier must not be co-located or operating in conjunction with any other antenna or amplier.4.5 When covering large areas a splitter can be used to allow for more than one inside antenna. Extension cables can also be used if the weak signal area is located far from the location of the outside antenna. For coax runs more than 20’ use 9913 or equivalent coax.NOTE: For Maximum gain (60 dB), keep a separation distance of at least 75 feet between the outside and inside antennas. Closer spacings may be used, but may cause the amplier to (automatically) reduce its gain.NOTE: When using the Yagi antenna make sure the Yagi is pointed away from the inside antenna.ALL LIGHTS GREEN = 60 dB GAINLIGHT D OFF = 2 dB REDUCTIONLIGHT D & C OFF = 10 dB REDUCTIONLIGHT D, C & B OFF = 20 dB REDUCTIONLIGHT A RED = 40 dB REDUCTION4.2 Indicator Lights
45For maximum gain, keep a separation distance of at least 75 ft between the outside and inside antennas.AC/DCPower SupplyAmplifierInside Antenna toAmplifier ConnectionCellSiteSupportsMultipleUsersOutside AntennaYagi Antenna ShownOutside Antenna toAmplifier ConnectionInside AntennaOptional DomeAntenna ShownAMPLIFIER LAYOUTDIAGRAMIf using the Yagi Antenna,Make sure the Yagi is not pointedtoward the inside antenna.5. AMPLIFIER SPECIFICATIONS FOR CELLULAR MODELPart # 801106Frequency 824-849 MHz Uplink 869-894 MHz DownlinkGain (up/down) 60 dB MaxFlatness (up/down) +/- 2.5 dB Max RF (up/down) + 32 dBmNoise Figure (down) 3 dB nominal Isolation Uplink/Downlink More than 90 dBPower Consumption 13.8 V, 1.5 AReceiver overload light Outside antenna has exceeded -5 dBMTransmit overload light Inside antenna has exceeded -5 dBMAMPLIFIER SPECIFICATIONS FOR iDEN MODELPart # 804006Frequency 806-821MHz Uplink 851-866MHz DownlinkGain (up/down) 60 dB MaxFlatness (up/down) +/- 2.5 dB Max RF (up/down) + 32 dBmNoise Figure (down) 3 dB nominal Isolation Uplink/Downlink More than 90 dBPower Consumption 13.8 V, 1.5 AReceiver overload light Outside antenna has exceeded -5 dBMTransmit overload light Inside antenna has exceeded -5 dBMAMPLIFIER PHYSICALSPECIFICATIONSConnectors N-Female 50 OhmsDimensions 4.5” x 3.5” x 1.25” (11.4 x 8.9 x 3.2 cm)Weight 1.5 lbs (682 gr)
676. OPTIONAL ACCESSORIES/ANTENNA OPTIONS6.1 3 dB Splitter (Part# 859901)6.2 6 dB Tap (Part# 859906) & 10 dB Tap (Part# 859907)6.3 Coax Cable Extensions 50Ω (see chart on next page)6.4 Antenna Options:Inside Antenna Options Outside Antenna Option301103 - Magnet Mount, 5 dBi 301111 - Yagi, 13 dBi301106 - Low Prole, 2.2 dBi301113 - Mini Magnet, 2.12 dBi301121 - Dome, 2.5 dBi301122 - Panel, 7 dBi6.5 N-Male to FME-Male adapter (Part# 971113) Adapts 9913 Coax to t the Amplier6.6 Lightning Surge Protection (Part# 859903)WARNING: Lightning protection is recommended for all installations.7. TECH SUPPORTIf you need further assistance with your installation:1) Call us Toll-Free at 866-294-1660 (8:00 AM – 4:30 PM Mountain Time)2) E-mail tech support at tech@wilsonelectronics.com3) Go to www.wilsonelectronics.com8. WARNINGSWARNING: The outside antenna used with this amplier must be xed-mounted on an out-door permanent structure with a separation of at least 20 feet from all persons during normal operation.WARNING: The inside antenna used with this amplier must have a separation distance from all persons that is at least: 9 inches for the 2.5 dBi Dome antenna. 14 inches for the 7 dBi Panel antenna. The amplier must not be co-located or operating in conjunction with any other antenna or amplier.WARNING: Verify that both the Outside and Inside Antennas are connected before plug-ging in the AC-DC power supply to the power outlet.WARNING: Lightning protection is recommended for all installations. Lightning protection is required for warranty validation.951110 2’ Extension Cable RG58U Low Loss Coax(N-Male to FME Female)Used with the Yagi antenna to help nd the optimum signal strength (for installation purposes only).951101 5’ Extension Cable RG58ULow Loss Coax(0.6 db loss)951102 10’ Extension Cable RG58ULow Loss Coax(1.2 db loss)951103 15’ Extension Cable RG58ULow Loss Coax(1.8 db loss)951104 20’ Extension Cable RG58ULow Loss Coax(2.4 db loss) N-Male to FME Female951113 2’ Extension Cable 9913 Equivalent Ultra Low Loss Coax(0.08 db loss) Jumper Coax - Can be used to con-nect a splitter behind an amplier.951108 20’ Extension Cable 9913 EquivalentUltra Low Loss CoaxOnly use 9913 Equivalent Low Loss Coax for extensions 20’ or longer (0.8 db loss)951105 30’ Extension Cable 9913 EquivalentUltra Low Loss Coax(1.2 db loss)951106 50’ Extension Cable 9913 EquivalentUltra Low Loss Coax(2.0 db loss)951117 75’ Extension Cable 9913 Equivalent Ultra Low Loss Coax(3.0 dB Loss)951107 100’ Extension Cable 9913 Equivalent Low Loss Coax(4.0 db loss)EXTENSION CABLE CHARTRG58U - FME connectors / 9913 Equivalent - N connectorsOperation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when mul-tiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device.The information provided by Wilson Electronics, Inc. is believed to be complete and accurate. However, no respon-sibility is assumed by Wilson Electronics, Inc. for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use.Copyright © 2004 Wilson Electronics, Inc.
8Trucker 3/8"MountMiniMagnetMagnetMountLowProfileYagiSingle-BandDomePanelOptional AccessoriesCoax Cable ExtensionUltra Low Loss CoaxLightning SuppressorFME Male toN-Male3 dB Splitter6 dB Tap10 dB Tap15 DAY MONEY BACK GUARANTEE All Wilson products have a 15 day money back guarantee with Proof of Purchase1 YEAR WARRANTYThe Wilson amplifier is warranted for one year against defects in workmanship and/or materials and will be repaired or replaced, at the discretion of the manufac-turer, to the original purchaser with dated proof of purchase or sales receipt.If you have questions about your amplifier please call technical support call 1-866-294-1660 or E-mail tech@wilsonelectronics.comMost warranty cases can be handled by taking the amplifier and the re-ceipt to the store where it was purchased. If inconvenient, the amplifier and a copy of the receipt, may be sent to the factory, at purchasers expense, where it may be repaired or replaced and returned shipping paid. Warranty does not cover damages caused by abuse, misuse, and negligence.801106_804006_005

Navigation menu