Wilson Electronics 8012ASM Mobile Wireless Cellular/PCS SmartTech Amplifier User Manual 2

Wilson Electronics, LLC Mobile Wireless Cellular/PCS SmartTech Amplifier Users Manual 2

Contents

Users Manual 2

Mobile WirelessDual BandCellular/PCSSmart TechnologyTM Amplifi erPART# 801201-AFCC ID: PWO8012ASMIC: 4726A-8012ASMInstallation GuideWilson Electronics, Inc.3301 E. Deseret Drive, St. George, Utah 84790For additional technical support go towww.wilsonelectronics.comPhone: 1-866-294-1660 Fax: 1-435-656-2432MOBILEWirelessThe term “IC:” before the radio certification number signifiesthat Industry of Canada technical specifications were met.Cellular & PCSAnalog & Digital - CDMA, GPRS, GSM, TDMA, 1x, HSDPA
21. PURPOSE OF THE AMPLIFIERThis Wilson Smart Technology™ Amplifi er greatly improves signal strength inside a vehicle without a physical connection to the phone or cellular data card. It also allows multiple devices to be used simultaneously.2. PACKAGE CONTENTS• Bi-Directional Amplifi er• DC plug-in power supply• Low Profi le Antenna (Coax Included)• 6’ Extension Cable• Small Antenna3. HOW THE AMPLIFIER FUNCTIONSThe signal is received by the outside antenna from the cell site. It is then AMPLIFIED and transmitted to your phone through the inside antenna. When the phone transmits, the signal is received by the inside antenna. It is then AMPLIFIED and transmitted to the cell site through the outside antenna (not included).4. AMPLIFIER SYSTEM INSTALLATION (See Illustration on pg. 5)4.1 Mounting the Amplifi er4.1.1 Select a suitable location to mount the AMPLIFIER. The amplifi er can be mounted to the selected location using screws. (Screws not included.) Mount the AMPLIFIER away from direct sunlight, excessive heat and/or moisture. The amplifier needs proper ventilation.PACKAGE CONTENTSBi-DirectionalAmplifierOPTION ALow ProfileAntenna(Coax Included)DC PowerSupply6' ExtensionCableOPTION BSmallAntenna
34.2 Installing the Wilson Cellular Inside Antenna (2 options included)4.2.1A (option A) - The inside antenna should be mounted approximately 1 foot or less from where the phone is used. The best place to mount the inside antenna is shoulder height on the side of the drivers seat. The closer the inside antenna is placed to the phone, the better the performance. See option A.Do not mount on a surface near metal. 4.2.1B (option B) - For convenience, the Small Antenna directly attached to the phone will perform as well as a Direct Connection Amplifi er or similar to the Low Profi le antenna attached directly to the phone. The Small Antenna must be directly connected to the back of the phone using Velcro (included). The Small Antenna will not work away from the phone like the Low Profi le antenna. Connect the 6’ extension cable to the Small Antenna (included). Attach Small Antenna to the back of the phone. See option B.4.2.2 Connect the Inside Antenna (A) or 6’ Extension Cable (B) to the side labeled “INSIDE ANTENNA” on the AMPLIFIER.Amplifi erLow Profi leAntennaAmplifi er 6’ Extension Cable Small AntennaSmall Antenna placement is depen-dant upon the location of the phones antenna. Place the Small Antenna as close as possible to the phones antenna.WARNING: Do not plug the amplifier directly into the phone using a phone specific adapter.
44.3 Installing the Wilson Cellular Outside Antenna (Sold Separately)4.3.1 Select an outside mounting location. For best performance keep the antenna centered on the vehicle’s roof.4.3.2 The outside antenna should be located in an area with at least a 12” radius clear of obstructions, and other radiating elements.NOTE: If the vehicle has a sunroof, place the outside antenna away from the sunroof so that the inside antenna is shielded from the outside antenna by metal. This is very important to avoid oscillation.4.3.3 Connect the Outside Antenna to the AMPLIFIER side labeled “OUTSIDE ANTENNA”.NOTE: Do not place the outside antenna in the vehicle without turning the amplifi er off.For example, when at the car wash. This will cause damage to your amplifi er.NOTE: Do not use a glass mounted antenna with a mobile wireless amplifi er.4.4 Connect the DC Power Supply4.4.1 Connect the large end of the DC Power Supply into your cigarette lighter and the other end into the input on your amplifi er. Use only the supplied power supply.4.5 Indicators Lights4.5.1 PWR - Power Indicator Light – Indicates power to the unit.800 MHz & 1900 MHz dual color Green/Red indicatorsGreen – Amplifi er is operating properly.Red – Indicates the amplifi er is oscillating (needs more separation between the Inside and Outside Antennas) and/or the cell sites signal is strong and the amplifi er has powered down. (see below)Oscillation – Try moving the outside antenna to a different location, creating more separation from the inside antenna. The inside antenna should be mounted within one foot (1’) of where the cell phone is being used.Strong Cell Signal – The amplifi er is designed to power down when the cell site signal is strong. If you are installing the amplifi er where the cell signal is strong, go to an area with low signal strength and verify that the light turns to Green.NOTE: You do not need amplifi cation when the cell signal is strong. The amplifi er is on only when the green light is on. In the city, you may only need amplifi cation when the signal fades from buildings or other structures blocking the signal.
5MOBILEAMPLIFIER LAYOUTCell Phone(s)InsideAntennaOutsideAntennaAmplifierDCPowerSupplyCellSite5. AMPLIFIER SPECIFICATIONSDual Band 800 / 1900 MHzPart Number 801201-AConnectors FME-Male 50 OhmsDimensions 5.6 x 3.6 x 1.7 inch or 14.2 x 9.1 x 4.4 cmWeight 1.44 lbs or 0.65 kgFrequency 824-894 MHz / 1850-1990 MHzGain (up/down) 37 dB / 43 dBLinear Output Power +30 dBmMax Output Power 3 watts (Cell Site Controlled)Max RF (up/down) +35 dBm / +10 dBmNoise Figure (typical) 3 dB nominalIsolation Uplink/Downlink more than 90 dBPower RequirementsAmplifi er Usage 6 V, 3 A (subject to Uplink power)
66. FEATURESAdvanced Electronics Receive & Transmit Better Than Your Cell Phone or Cellular Data Card• Power Control Logic Ensures Maximum Gain is Within Cellular Standards• Allows Multiple Devices to be Used Simultaneously• Maximum 3 Watts Output Power (cell site controlled)• Designed for All Systems Including CDMA, EDGE, GPRS, GSM, TDMA,1x, HSDPA• LED - Power & Overload Shutdown/Oscillation• Overload Protection Circuit – Protects Cell System from Overload• Automatic Reset – if overload occurs7. OPTIONAL ACCESSORIES/ANTENNA OPTIONS7.1 Outside Antenna OptionsSee page 88. TECH SUPPORTIf you need further assistance with your installation:1) Call us Toll-Free at 866-294-16602) E-mail tech support at tech@wilsonelectronics.com3) Go to www.wilsonelectronics.comOur Hours of Operation are: 8:00 AM – 4:30 PM (Mountain Time)The information provided by Wilson Electronics, Inc. is believed to be complete and accurate. However, no responsibility is assumed by Wilson Electronics, Inc. for any business or per-sonal losses arising from its use, or for any infringements of patents or other rights of third parties that may result from its use. Copyright © 2006 Wilson Electronics, Inc.
79. NOTES & WARNINGSWARNING: Verify that both the outside antenna and the inside antenna are connected before powering up the amplifi er.WARNING: Do not place the outside antenna in the vehicle without turning the amplifi er off. For example, when at a car wash. This will cause damage to the amplifi er.WARNING: The outside antenna must be mounted with a separation distance of at least 17 inches from any of the vehicle occupants or nearby persons and must not be co-located or operating in conjunction with any other antenna or amplifi er. Use of a cellular amplifi er with antenna gains higher than 6.12 dBi is in violation of FCC regulations for which the offender is fully liable. All Wilson Mobile Antennas are 6.12 dBi or less.WARNING: The inside antenna must be mounted with a separation distance of at least 1 inch (2.5 cm) from all persons and must not be co-located in conjunction with any other antenna or amplifi er.WARNING: Do not plug the amplifi er directly into the phone using a phone specifi c adapter.WARNING: Do not use a glass mounted antenna with a mobile wireless amplifi erWARNING: Use only the DC Power Supply that comes with the amplifi er, or a replacement supplied by Wilson.Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.Leaving the amplifier on in an unused vehicle for days may drain your battery. This can be avoided by plugging into an ignition switched power source.The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device.In order to prevent excessive input levels from distorting or otherwise overdriving this amplifier, the maximum uplink RF output is 35 dBm, and the maximum downlink RF output is 10 dBm. When an input tends to create greater than these maximum levels, a switching circuit will reduce the RF output by as much as 50 dB.The voltage and current into the final amplification stage are: TX: 6 V DC 3 A RX: 3.6 V DC 50 mA
815 DAYMONEY BACKGUARANTEEAll Wilson products have a 15 day money backguarantee with Proof of Purchase1 YEAR WARRANTYThe Wilson amplifier is warranted for one year against defects in workmanship and/or materials and will be repaired or replaced, at the discretion of the manufac-turer, to the original purchaser with dated proof of purchase or sales receipt.If you have questions about your amplifier please call technical support at 1-866-294-1660 or E-mail tech@wilsonelectronics.comMost warranty cases can be handled by taking the amplifier and the re-ceipt to the store where it was purchased. If inconvenient, the amplifier and a copy of the receipt, may be sent to the factory, at purchasers expense, where it may be repaired or replaced and returned shipping paid. Warranty does not cover damages caused by abuse, misuse, and negligence.801201A_003 / 03.27.06MiniMagnet MiniGlass NMOTrucker Magnet Mount Glass Mount NMO Mount RV Trucker Spring Mount Trucker Mirror Mount Dual BandThis device has been designed to operate with the antennas listed below, and having a maximum gain of 6.12 dB. Antennas not included in this list or having a gain greater than 6.12 dB are strictly prohibited for use with this device. The required antenna impedance is 50 ohms.To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that permitted for successful communication.

Navigation menu