Wilson Electronics 8012SM WIRELESS CELL PHONE AMPLIFIER User Manual INSTALLATION GUIDE

Download:
Mirror Download [FCC.gov]
Document ID	750268
Application ID	dqJ/YG84h09aS5NwScqMkg==
Document Description	INSTALLATION GUIDE
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	50.74kB (634210 bits)
Date Submitted	2007-01-24 00:00:00
Date Available	2007-01-24 00:00:00
Creation Date	2007-01-02 13:45:19
Producing Software	Adobe PDF Library 7.0
Document Lastmod	2007-01-02 14:07:49
Document Title	INSTALLATION GUIDE
Document Creator	Adobe InDesign CS2 (4.0.4)

Amplifier
Installation
Guide
SOHO Wireless
Dual-Band
Cellular / PCS
Amplifier
MODEL# 271245
PART# 801245
Contents:
Guarantee and Warranty · · · · · · · · · · · · · · · · · · · · · · · · 1
Antenna Options · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 2
How It Works · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · 3
Before Getting Started · · · · · · · · · · · · · · · · · · · · · · · · · · 3
Installation Overview · · · · · · · · · · · · · · · · · · · · · · · · · · · 3
Installing the Outside Antenna · · · · · · · · · · · · · · · · · · · 4
Installing the Inside Antenna · · · · · · · · · · · · · · · · ·
Installing the Amplifier · · · · · · · · · · · · · · · · · · · · · · · · · · 6
Powering up a Wilson Amplifier · · · · · · · · · · · · · · · · · · · 7
Understanding the Amplifier Lights · · · · · · · · · · · · · · · · · 8
Warnings and Recommendations · · · · · · · · · · · · · · · · · · 9
About Wilson Electronics · · · · · · · · · · · · · · · · · · · · · · · · 10
Amplifier Specifications · · · · · · · · · · · · · · · · · · Back Cover
Warning: This manual contains
important safety and operating information.
Please read and follow the instructions
in this manual. Failure to do so could be
hazardous and result in damage to your
amplifier.
Wilson
®
Electronics, Inc.
30-Day Money-Back Guarantee
All Wilson Electronics products are protected by Wilson’s 30-day money-back
guarantee. If for any reason the performance of any product is not acceptable,
simply return the product directly to the reseller with a dated proof of purchase.
1-Year Warranty
Wilson Electronics amplifiers are warranted for one (1) year against defects in
workmanship and / or materials. Warranty cases may be resolved by returning the
product directly to the reseller with a dated proof of purchase.
Amplifiers may also be returned directly to the manufacturer at the consumer’s
expense, with a dated proof of purchase and a Returned Material Authorization
(RMA) number supplied by Wilson Electronics. Wilson shall, at its option, either
repair or replace the product. Wilson Electronics will pay for delivery of the repaired
or replaced product back to the original consumer.
This warranty does not apply to any amplifiers determined by Wilson Electronics
to have been subjected to misuse, abuse, neglect, or mishandling that alters or
damages physical or electronic properties.
RMA numbers may be obtained by phoning Technical Support at 866-294-1660.
Operation is subject to the following two conditions: (1) This device may not cause
interference, and (2) this device must accept any interference, including interference that
may cause undesired operation of this device.
Disclaimer: The information provided by Wilson Electronics, Inc. is believed to
be complete and accurate. However, no responsibility is assumed by Wilson
Electronics, Inc. for any business or personal losses arising from its use, or for
any infringements of patents or other rights of third parties that may result from
its use.
Copyright © 2007 Wilson Electronics, Inc. All rights reserved.
Installation Instructions for the Following Wilson Amplifier:
SOHO Wireless Dual-Band Cellular/PCS Amplifier
Model # 271245, Part # 801245
FCC ID: PWO8012SM IC: 4726A-8012SM
The term “IC” before the radio certification number only signifies that Industry Canada
technical specifications were met.
Inside this Package
• SOHO wireless amplifier
• AC/DC 6 volt power supply
SOHO wireless
amplifier
6 V DC plug-in
power supply
Additional Required Equipment (sold separately)
• Outside antenna
• Inside antenna
• Antenna coax cable
Antenna Options
(outside)
(outside)
(outside)
(inside)
(inside)
(inside or outside)
(inside)
(inside)
13 dB 800 MHz Yagi Cellular Antenna (301111)
1900 MHz Yagi PCS Antenna (301124)
800 MHz Yagi Cellular Antenna (301129)
Dual-Band Panel Antenna (301135)
Dual-Polarity Dome Antenna (301123)
Dual-Band Dome Antenna (301121)
Low Profile Cellular Antenna (301106)
Mini Magnet-Mount Antenna (301103)
Magnet-Mount Antenna (301113)
Dual-Band Trucker Antenna (301101)
How it Works
Your new Wilson SOHO Wireless Dual-Band Amplifier has been carefully engineered to
enhance the performance of your inside or cellular data card in small office/home office
applications. Its advanced technology is designed to significantly improve voice and
data signal quality and reduce disconnects and drop-outs. The amplifier works with two
antennas (sold separately): one communicates with the outside (the outside antenna) and
the other communicates with your inside or laptop data card (the inside antenna).
The outside antenna will collect the outside signal and send it through a cable to the
amplifier. The signal is then boosted and sent through a cable to the inside antenna, which
communicates with your inside or data card. When the inside or data card transmits, the
inside antenna picks up the signal and sends it to the amplifier where it is boosted and
sent through the outside antenna to the outside.
Wilson Electronics manufactures a wide variety of antennas and accessories to help you
customize your SOHO Wireless Dual-Band Amplifier for your specific application (see
page 2). Contact your dealer or visit www.wilsonelectronics.com.
Before Getting Started
This guide will help you properly install Wilson’s SOHO Wireless Dual-Band Amplifier. It is
important to read through all of the installation steps for your particular application
prior to installing any equipment. Read through the instructions, visualize where all
the equipment will need to be installed and do a soft installation before mounting any
equipment. If you do not understand the instructions in full, please contact Wilson technical
Support at 866-294-1660.
Installation Overview
The following steps provide a summary of the amplifier/installation process using a Yagi
antenna as the outside antenna and a panel antenna as the inside antenna. However,
they are not a substitute for the complete installation instructions on the following pages,
which you should read thoroughly. Be sure to read and follow the instructions that come
with your specific antennas.
STEP 1 Install the Outside Antenna
Mount the Yagi antenna to a fixed location (such as a pole) on the roof of your building. Be
sure it is pointing toward the nearest cell tower and away from where you plan to install the
inside antenna. IMPORTANT: The outside antenna must have a separation of at least
24 inches from all persons during normal operation.
STEP 2 Install the Inside Antenna
Attach the panel antenna as close as possible to the center of the area where the signal
needs to be amplified. Ensure there is a minimum separation of 20 feet between the
outside and inside antennas. IMPORTANT: The inside antenna must have a separation
of at least 8 inches from all persons during normal operation.
STEP 3 Install the Amplifier
Position the amplifier in a well-ventilated location near a power outlet. Attach the antennas
to the amplifier using 50-ohm or equivalent coax cable (available in different lengths from
Wilson Electronics).
STEP 4 Power up the Amplifier
IMPORTANT! Before connecting the power supply, ensure that both the inside and outside
antenna cables are connected. Also ensure that all insides and cellular data cards within
20 feet of the inside antenna are turned off. Plug the supplied 6-volt power supply into
the amplifier and then into a wall outlet.
Installing the Outside Antenna
The antenna that communicates with the outside should be mounted on the outside of the
building—this is the preferred location and will give the best performance. Alternatively,
locating this antenna inside the building near a window will also work under certain
conditions. IMPORTANT: The outside antenna must have a separation of at least 24
inches from all persons during normal operation.
Outdoor Installation
For best results, use a Wilson Yagi antenna that is compatible with the frequency of your
cellular service provider. A dual-band trucker antenna will also work. Mount the antenna as
high as possible on your building for optimum signal reception and transmission.
Follow the specific installation instructions included with the outside antenna. Lightning
protection is recommended for all outdoor antenna installations. Take extreme care to
ensure neither you nor the antenna come in contact with any electrical power lines. Ensure
there are three feet of clearance in all directions surrounding the antenna.
RF Signal
Cell Tower
Yagi Outside Antenna
Warning: Never point the front of
the Yagi antenna toward the inside antenna
- oscillation will result, causing an amber light
on the amplifier and gain reduction.
CORRECT
Warning: The outside antenna must be
installed with a separation of at least 24 inches
from all persons during normal operation.
Alternate Installation
Pointing toward
cell tower
NOT
CORRECT
If you choose to install the outside antenna
indoors, select a location near a window or
glass door where you have the strongest
existing cell signal. (See the illustration on
page 5.) Follow the specific installation
instructions included with the antenna.
Installing the Inside Antenna
The antenna that communicates with your inside or cellular data card should
be installed in the center of where the signal needs to be amplified. Wilson’s
magnet-mount, mini magnet-mount, dome and panel antennas will work well with
the SOHO Wireless Amplifier.
Outside
Antenna
Amplifier
Inside
Antenna
20 feet minimum separation
between inside antenna and
outside antenna
In the above illustration, Wilson mini magnet-mount antennas are being used
for both the outside antenna (on the window) and the inside antenna (on the
desk). Follow the specific instructions included with the antennas for your specific
application.
Warning: The inside antenna
must have a separation distance from all
persons that is at least 8 inches.
Warning: Connecting the amplifier
directly to the inside with use of an adapter
will damage the inside.
Installing the Amplifier
Select a location to install the amplifier that is away from excessive heat, direct
sunlight, moisture and that has proper ventilation. Do not place the amplifier in
an air-tight enclosure.
Recommended installation locations are:
• On a desk or table top
• In a bookshelf
• On the floor
In the illustration below, a Wilson Yagi antenna is being used as the outside
antenna, and a Wilson dome antenna is being used as the inside antenna.
Point Yagi antenna
away from cell phone
antenna
Outside
Antenna
Optional
1900 MHz
Yagi
Antenna
Shown
Antenna Separation
20 feet minimum separation
between inside
and outside antenna
Inside Antenna
Optional Dome
Antenna Shown
Amplifier
AC/DC
Power Supply
Supports
Multiple
Users
Run the outside antenna cable to the amplifier and attach it to the FME-male
connector labeled “outside antenna” on the amplifier. Run the inside antenna
cable to the amplifier and attach it to the FME-male connector labeled “inside
antenna” on the amplifier.
Note: Be careful when plugging the connectors in so as not to damage the
center pin.
Connect the outside antenna to the amplifier with 50-ohm or equivalent coax
cable (available in different lengths from Wilson Electronics). Place the inside
antenna in the center of the area needing the amplified signal. It is important
to have at least 20 feet of separation between the inside and outside antennas.
Closer spacing may result in oscillation, which will cause the amplifier to
automatically reduce its gain.
Powering up a Wilson Amplifier
1. IMPORTANT! Ensure that all insides and cellular data cards within 20 feet of
the inside antenna are turned off.
2. To verify proper installation of the amplifier and antennas, make sure that the
distance between the inside and outside antennas is a minimum of 20 feet.
3. If you are using an Yagi antenna as a outside antenna, never point the front of
the Yagi toward the inside antenna.
4. Ensure that both the outside antenna coax cable and the inside antenna coax
cable are connected to the amplifier before powering up the amplifier.
5. Plug the 6-volt power supply into the amplifier input marked “power” (carefully,
to avoid damaging the center pin) and then into a wall outlet.
Warning: Use only the power
supply provided in this package.
Use of a non-Wilson product may
damage your equipment.
Warning: Verify that both the
outside antenna and the inside
antenna are connected to the amplifier
before powering up the amplifier.
NOTE: The aluminum casing of a Wilson amplifier will adjust very quickly to the
ambient temperature of its environment. For example, in the summer, when
the attic of a house can easily exceed 100 degrees Fahrenheit, the amplifier
temperature may be 10 or more degrees higher. The casing will be hot to the
touch. Such high temperatures will not damage the amplifier, nor do they pose
a fire risk. As recommended in these instructions, install the amplifier in a
location with adequate ventilation. Keep the area free of items that could block
air flow to the amplifier.
Understanding the Amplifier Lights
The power light PWR will turn green
when the amplifier is successfully
powered up.
When the 800 MHz or 1900 MHz lights
are lit green, the amplifier is amplifying
the outside signal.
If one or both frequency lights turn red,
the amplifier is oscillating. To correct
this, you must increase the separation
between the inside and outside antennas
until all lights are green. After increasing
the separation, it is necessary to turn the
amplifier power off and back on to reset
the red lights. If one or both frequency
lights remain red, repeat this procedure
until both are green.
Warnings and Recommendations
Warning:
A Yagi antenna must always be located so the back or side points
to the inside antenna. Never point the front of the Yagi antenna
toward the inside antenna – oscillation will result, causing amber
light and gain reduction.
Warning:
Connecting the amplifier directly to the inside with use of an
adapter will damage the inside.
Warning:
Connect both the outside and inside antenna cables to the
amplifier before powering up the amplifier.
Warning:
Use only the power supply provided in this package. Use of a
non-Wilson product may damage your equipment.
Warning:
The outside antenna must have a separation distance from all
persons that is at least 24 inches. The inside antenna must have
a separation distance from all persons that is at least 8 inches.
Lightning protection is recommended for all in-building installations using an
outside antenna.
About Wilson Electronics
Wilson Electronics, Inc. has been a leader in the wireless communications
industry for nearly 40 years. The company designs and manufactures amplifiers,
antennas and related components that significantly improve cellular telephone
signal reception and transmission in a wide variety of applications, both mobile
and in-building.
With extensive experience in antenna and amplifier research and design, the
company’s engineering team uses a state-of-the-art testing laboratory, including
an anechoic chamber and network analyzers, to fine-tune antenna designs and
performance. For its amplifiers, Wilson uses a double electrically insulated RF
enclosure and outside simulators for compliance testing.
Wilson amplifiers feature patent-pending Smart Technology™ that enables them
to automatically adjust their power based on outside requirements. By preventing
oscillation, signal overload and interference with other users, these Smart
Technology™ amplifiers improve network Inside areas without compromising the
carrier’s system.
All products are engineered and assembled in the company’s 50,000-square-foot
headquarters in St. George, Utah. Wilson has product dealers in all 50 states as
well as Canada and Mexico, Central and South America.
BARS
INCREASE
YOUR
10
Amplifier Specifications
Dual Band
800/1900 MHz Specifications
271245
FME-Male
50 ohms
5.6 x 3.6 x 1.7 inch or 14.2 x 9.1 x 4.4 cm
1.44 lbs or 0.65 kg
824-894 MHz / 1850-1990 MHz
Model Number
Connectors
Impedance (input/output)
Dimensions
Weight
Frequency
Passband Gain (nominal)
800 MHz
1900 MHz
20 dB Bandwidth (nominal)
800 MHz (uplink/downlink)
1900 MHz (uplink/downlink)
50 dB
60 dB
Power output for single inside (uplink)
CDMA
GSM
EDGE
AMPS
Power output (uplink) for multiple
insides:
Number of
insides
Power output for single received channel
(downlink)
CDMA
GSM
EDGE
AMPS
Power output for multiple received
channels (downlink). The maximum
power is reduced by the number of
channels:
53.5 MHz / 47.7 MHz
86 MHz / 83 MHz
800 MHz
+30.9 dBm
+30.0 dBm
+30.4 dBm
+30.2 dBm
Maximum Power
800 MHz
1900 MHz
+25.0 dBm
+21.5 dBm
+19.0 dBm
+17.0 dBm
+15.5 dBm
+24.7 dBm
+21.2 dBm
+18.7 dBm
+16.7 dBm
+15.2 dBm
800 MHz
1900 MHz
+10.0 dBm
+11.0 dBm
+10.9 dBm
+10.3 dBm
+9.9 dBm
+9.9 dBm
+9.6 dBm
Noise Figure (typical)
Isolation (uplink/downlink)
Power Requirements
1900 MHz
+30.5 dBm
+29.7 dBm
+30.3 dBm
Maximum Power
Number of
channels
800 MHz
1900 MHz
-11.6 dBm
-15.1 dBm
-17.6 dBm
-19.6 dBm
-21.1 dBm
-3.1 dBm
-6.6 dBm
-9.1 dBm
-11.1 dBm
-12.6 dBm
3 dB nominal
> 90 dB
6 V, .5 A - 1.5 A (depends upon uplink power)
Notes:
1. Nominal gain is the maximum gain at any frequency in the passband.
2. Nominal bandwidth is the difference between two frequencies that are adjacent to the passband where the amplification is 20 dB
lower than the passband amplification. One of the frequencies is lower than the passband and the other is higher.
3. The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier
signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can
cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by
an attenuator at the output of the device.
4. The maximum power for 2 or more simultaneous signals will be reduced by 6 dB every time the number of signals is doubled.
Phone: 866-294-1660
Wilson® Electronics, Inc.
www.wilsonelectronics.com Fax: 435-656-2432
AIG SOHO 006 / 01.02.07

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
Page Count                      : 12
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:c1c3561d-0db2-4af8-8fef-4d65a3f7a1f7
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Create Date                     : 2007:01:02 13:45:19-07:00
Modify Date                     : 2007:01:02 14:07:49-07:00
Metadata Date                   : 2007:01:02 14:07:49-07:00
Creator Tool                    : Adobe InDesign CS2 (4.0.4)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 8685 bytes, use -b option to extract)
Instance ID                     : uuid:df7c076d-b256-4d57-8b76-0d368ccbaca7
Rendition Class                 : proof:pdf
Document ID                     : adobe:docid:indd:ba51b538-9aa1-11db-b299-cc4ddd11a368
Derived From Instance ID        : 577e59c2-9112-11db-a8db-b773cee23a31
Derived From Document ID        : adobe:docid:indd:577e59c0-9112-11db-a8db-b773cee23a31
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 300.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 300.00, 300.00, 300.00, 300.00, 72.00
Manifest Placed Y Resolution    : 300.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 300.00, 300.00, 300.00, 300.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:0B159C47BD78DB118A0C865BD0055347, uuid:6c5c9b94-5feb-4280-922c-a1b9371e2ea4, uuid:1BEDA7E3D489DA118200A07DB41E56A2, uuid:A51CE99DC21DDB11A875F2A89CEE8E85, uuid:0B159C47BD78DB118A0C865BD0055347, uuid:c420bcbc-c6a0-47d8-98b4-31812c9f027a, uuid:916b43a9-590d-43a9-87f6-88e47d36b2c6, uuid:0B159C47BD78DB118A0C865BD0055347, uuid:B49F0FB9E278DB119FF1D3EFB05F4A2F, uuid:B49F0FB9E278DB119FF1D3EFB05F4A2F, uuid:B49F0FB9E278DB119FF1D3EFB05F4A2F, uuid:0c58b044-d4f2-42f5-bd96-222b126761cf
Manifest Reference Document ID  : uuid:0A159C47BD78DB118A0C865BD0055347, uuid:AE3C53E87800DB119EE1FCBF77AD56DD, adobe:docid:photoshop:5a4dd2f3-716e-11d9-8b01-95a288864e59, adobe:docid:photoshop:e7c94402-7167-11d9-8b01-95a288864e59, uuid:CA8219BD24E5DA118AEE8EF45FC3436C, uuid:0A159C47BD78DB118A0C865BD0055347, adobe:docid:photoshop:f2061880-716d-11d9-8b01-95a288864e59, uuid:AC87D4362AE1DA118EFEE3A816DC7662, uuid:65A7F7E0BD80DB1182E6D73B2161714A, uuid:0A159C47BD78DB118A0C865BD0055347, uuid:46D8F35FBC78DB11BA159F3B05E8DC9A, uuid:46D8F35FBC78DB11BA159F3B05E8DC9A, uuid:46D8F35FBC78DB11BA159F3B05E8DC9A, uuid:535FFD7F2B39DB118D7BF698B9EDC986
Format                          : application/pdf
Creator                         : Adobe InDesign CS2 (4.0.4)

EXIF Metadata provided by EXIF.tools