Wilson Electronics BD800NB Amplifier Repeater User Manual User Guide
Wilson Electronics, LLC Amplifier Repeater User Guide
Contents
- 1. User Guide
- 2. Install Guide
User Guide
4 Wilson Electronics, Inc. 3301 E. Deseret Drive St. George, Utah 84790 wilsonelectronicscom oellwar@wnsuneleammcs com Phone 1-800-204-4104 Fax 1435-656-2432 USER’S GUIDE FOR THE IDEN IN BUILDING BI-DIRECTIONAL AMPLIFER/REPEATER MODEL: BDSOONB 3/19/2002 The information provided by Wilson Electronics, lnc. is believed to be complete and accurate. However. no responsibility is assumed by Wilson Electronics. lnc. for any business or personal losses arising from its use, or for any infringements of patents or other rights of third parties which may result from its use. WARNING: The outside and inside nntennn should be pheed at least lZin from any people or ehildren. A lightning rod should be added if the outside antenna is in any danger of being hit by lightning. Copyfighl Q 2001 Wilson Electronics. Inc. PAGE 2 l. PACKAGE CONTENTS I.l Amplifier/Repeater L2 AC-lo—DC Transformer [3 Antennas: 800MHz Magnet Mount (outside), Shun 800MHz Magnet (inside) L4 2 N-Male To FMEAMaIe Adaplels 2. OPTIONAL ACCESSORIES ll RF Splitter 2.2 Coax Cable Extensions 509 Bi—Directional Amplifier Package Dual “and M.... Max“ (in: ("Alvin Fitrllmln own-mt mm". Amphlirr N male —|'MI: mnlc N uulr I‘vfl nulf Q = .r‘!. ulml 1L Manta Mmll L RPS; (In > Midst s L} 2 15“ it» I x \‘,~-~ul ralu'unna PAC]: 3 3. AMPLIFIER 3.1 About The Amplifier greatly improves signal strength when using your portable iDEN phone inside the building. The signal is received by the outside antenna from the cell site. It is then AMPLIFIED/REPEA'IED and then transmitted to your iDEN phone through the inside antenna. When the phone transmits it is received by the inside antenna. It is then AMPLIFIED/REPEATED and then transmitted to the cell site through the outside antenna. 3.2 Specifications: FREQUENCY: 806-82” MHZ UPLINK 85l-866 MHZ DOWNLlNK GAIN: 50 DB UPLINK 50 DB DOWNLlNK FLA'l'NESS: UPLINK +/- 3 DB DOWNLlNK +/- 308 MAX RF OUTPUT POWER: UPLINK lW DOWNLlNK 0.0IW NOISE FIGURE: UPLlNK/DOWNLINK (LESS THAN OR EQUAL TO SDB) UPLINK DOWNLlNK ISOLATION: MORE THAN 60 DB POWER CONSUMPTION: 13.8V. 1.5A CONNECTOR: N-FEMAI.E 50 OHMS DIMENSIONS: 5.5 x 4.3 x L4 (INCHES) OR 14.0 x 10.8 x 3.5(CM) WEIGl IT: 1.32 POUNDS OR 6000 PAGE 4 4. AMPLIFIER/REPEATER INSTALLATION (REFER TO ILLUSTRATION) 4.1 Installing the Outside Antenna 4.1.1 Select a location on the roof using your iDEN phone in test mode to find the best signal strength. 4.l.2 The Outside Antenna should be located in an area with at least a 3’ radius clear of obstructions and other radiating elements mm a w um mam” A Nahk‘mx Uuhnll tlflum m nut mum. l. hut-Ml kqum n uwlhcfluru \m;vl|lm karma 4 mum”. mm m an u, AMPLIFIER-LAYOUT ILLUSTRATION PAGE 5 4.2 Installing The Amplifier/Repeater 4.2.1 Mount the AMPLIFIER/REPEATER on a wall or ceiling. 4.2.2 Connect the Outside Antenna to the AMPLIFIER/REPEATER side labeled “ANTENNA" using one of the supplied adapters (N-Male to FME-Male). 4.3 Installing The Inside Antenna 4.3.I Connect the Inside Antenna to the side labeled “PHONE" on the AMPLIFIER/REPEATER. 4.3.2 The Inside Antenna should be centered in the weak signal area 0 The INSIDE ANTENNA should be at least 8' from the ground. 4.4 When covering large areas a splitter can be used to allow for the addition of inside antennas. Extension cables can also be used if the weak signal area is located far from the location of the outside antenna. NOTE: A minimum of 20’ coax extension is recommended for isolation between antennas. PAGE 6
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2002:04:15 14:48:34 Producer : Acrobat Distiller 4.0 for Windows Modify Date : 2002:04:15 14:48:37-04:00 Page Count : 6EXIF Metadata provided by EXIF.tools