Winegard Tv Antenna Hd7084P Users Manual
HD7697P to the manual 02cfc467-c10f-4357-981e-a6d4e4537c0e
2015-02-03
: Winegard Winegard-Tv-Antenna-Hd7084P-Users-Manual-479912 winegard-tv-antenna-hd7084p-users-manual-479912 winegard pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
HOW TO PROVIDE LIGHTNING PROTECTION FOR TV ANTENNA AND SET Fig. 10 Example of antenna grounding as per National Electrical Code, ANSI/NFPA 70 Step 1. Mount the lightning arrestor or 75 ohm coaxial grounding block as close as possible to where the 75 ohm coaxial cable downlead enters the house. See Figure10. Step 2. The ground wires for both the mast and the downlead should be copper or aluminum wire, number eight (8) or larger. See Figure 10. Step 3. The downlead wire from the antenna to the lightning arrestor and the mast ground wire should be secured to the house with stand-off insulators, spaced from four (4) to six (6) feet apart. See Fig. 10. Antenna Lead In Wire Digital/High Definition Ground Clamp Electric Service Equipment NOTE: In the case of a “ground up” antenna installation, it may not be necessary to ground the mast if the mast extends four or more feet int the earth. Consult a TV serviceman for the proper depth in your location. 769 Series Antennas Antenna Discharge Unit (NEC Section 810-20) (May substitute a 75 ohm Coax Grounding Block) Grounding Conductors (NEC Section 810-21) Ground Clamps VHF/UHF MODEL HD7084P & HD7697P ND S N IS E TH TATIO T IN S PO RDS WA TO Power Service Grounding Electrode System (NEC Art 250, Part H) NEC - National Electrical Code 90 DAY LIMITED WARRANTY Winegard Company warrants this Winegard product against any defects in materials or workmanship within 90 (ninety) days from date of purchase. No warranty claim will be honored unless at the time the claim is made, you present proof of purchase to an authorized Winegard dealer (if unknown, please contact Winegard Company, 3000 Kirkwood Street, Burlington, IA 52601-2000, Telephone 800-288-8094). Winegard Company (at its option) will either repair or replace the defective product at no charge to you. This warranty covers parts, but does not cover any costs incurred in removal, shipping or reinstallation of the product. This limited warranty does not apply if the product is damaged, deteriorates, malfunctions or fails from: misuse, improper installation, abuse, neglect, accident, tampering, modification of the product as originally manufactured by Winegard, usage not in accordance with product instructions or acts of nature such as damage caused by wind, lightning, ice or corrosive environments such as salt spray and acid rain. The 90 Day Warranty is provided on the condition that the equipment is properly delivered with all handling and freight charges prepaid to your Winegard dealer for return to our factory for repair or replacement. Winegard dealers will arrange for the replacement or repair and return to you without charge the product which failed due to defective material or workmanship. WINEGARD COMPANY WILL NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, MADE BY ANY OTHER PERSON. ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIMITED TO THE 90-DAY PERIOD OF THIS WARRANTY. The foregoing shall be the sole and exclusive remedy of any person, whether in contract, tort or otherwise, and Winegard shall not be liable for incidental or consequential damage or commercial loss, or from any other loss or damage except as set forth above. Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Rev. 2/08 Printed in U.S.A. © Winegard Company 2002 Rev3 12-13 1450291 VHF/UHF MODEL HD7084P D EN S HIS TION T A T T N I S PO RDS WA O T VHF/UHF MODEL HD7697P Register your product at winegard.com/myantenna WARNING INSTALLATION OF THIS ANTENNA NEAR POWER LINES IS DANGEROUS. FOR YOUR SAFETY, FOLLOW THE INSTALLATION INSTRUCTIONS. NOTE To prevent damage in shipping, the second set of elements from the rear of the boom are folded to the reverse side. You can identify these elements by the tags attached to them. Follow the directions on the tags carefully. Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601-2000 STEP 1. Remove the rear section of antenna from carton (long elements). Lay it on the ground with the end with the plug pointing toward you. Starting with the element nearest you, unfold the first element CLOCKWISE about 80° and click to lock position. See Figure 1. STEP 2. Grasp both ends of the second element from the rear of the boom. Lift the ends of the element just enough to slide over the other elements to the front and rear and ROTATE ABOUT 100° COUNTER CLOCKWISE to lock. See Fig. 1. STEP 3. Unfold the rest of the elements on this side of the antenna to the lock position, being sure to alternate the elements. See Figure 2. STEP 4. Turn the antenna over and repeat steps 1, 2 and 3. Again lift and rotate the second element just enough to slide over the other elements. See Figure 3. Fig. 2 Lift and Rotate Fig. 3 Fig. 1 STEP 6. Unfold UHF directors, as shown in Figure 5. Fig. 4 Fig. 5 REFLECTOR BOOM MAIN BOOM REFLECTOR BOOM ENDS OF CLIPS SHOULD POINT AWAY FROM MAIN BOOM STEP 8. To install the boom brace remove the bolts and hex nuts. Attach the boom brace to the reflector boom first, making sure that the mast clamps are on the same side, see Figure 7. Do not tighten the bolt and hex nut. STEP 9. Swing the boom brace down onto the main boom and insert the bolt and hex nut, see Figure 7. Tighten both bolts and hex nuts securely. Fig. 7 Fig. 8 CARTRIDGE HOUSING RECEPTACLE Antenna shown from top side with front of rear section pointing away from you. STEP 5. Unfold the elements of the front section of the antenna. The elements should be on the top side of the front section of the antenna. Remove the bolt and hex nut, (see Fig 4) from the tapered end of the front boom and slide the tapered end into the front of the rear boom. The cartridge housing receptacle on the rear section of the antenna is attached to the bottom of the rear boom at the factory. Replace the bolt, and hex nut. Tighten securely. Fig. 6 STEP 7. Unfold the reflector booms slowly until they lock in place. Then unfold the elements on the reflector booms. See Figure 6. NOTE: To prevent damage in shipping, the second set of elements from the rear of the boom are folded to the opposite side. Antenna shown from underside with front of rear section pointing away from you. STEP 10. To attach the cartridge housing to the antenna, align the snaps on the cartridge housing with the snap holes on the cartridge housing receptacle on the antenna and push the housing into the receptacle until it snaps into place. See Figure 8. STEP 11. Attach the 75 ohm coaxial cable to the cartridge housing. See Figure 8. Slide weather boot over connector and boot collar. CARTRIDGE HOUSING BOOT COLLAR STEP 12. To mount the antenna on the Fig. 9 mast, loosen nuts on the main boom and boom brace mast clamps. Slide both mast clamps over the mast pointing the front of the antenna (small end) towards stations and tighten the boom brace mast clamp securely. Let the main boom mast clamp slide down the mast until the boom brace supports the main boom. Tighten the main boom mast clamp securely. See Figure 9. STEP 13. The 75 ohm coaxial cable downlead may be secured to the mast by either taping it or use of plastic wire ties. DOWNLEAD JACK 75 OHM COAXIAL CABLE (DOWNLEAD) WEATHER BOOT MAST CLAMP HEX NUT MAST CLAMP INSERT U-BOLT MASTING 2" OD MAX.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.7 Linearized : Yes XMP Toolkit : Adobe XMP Core 5.0-c060 61.134777, 2010/02/12-17:32:00 Instance ID : uuid:31c00b78-c9b9-4af9-868e-73b7f06df752 Document ID : xmp.did:65FF19D60568E311B6E5F05FFFF9DAFC Original Document ID : adobe:docid:indd:bc60ca18-d247-11df-b146-c97dc1dab207 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:C312D6DA0368E311B6E5F05FFFF9DAFC Derived From Document ID : adobe:docid:indd:bc60ca18-d247-11df-b146-c97dc1dab207 Derived From Original Document ID: adobe:docid:indd:bc60ca18-d247-11df-b146-c97dc1dab207 Derived From Rendition Class : default History Action : saved, saved, saved, saved, saved, saved, saved, saved, saved, saved History Instance ID : xmp.iid:3C954F23A45BE011BDCFE2EBB26B582A, xmp.iid:3D954F23A45BE011BDCFE2EBB26B582A, xmp.iid:EE60DBE46F5CE011AD9BF6153801DF36, xmp.iid:5FE1DDA9FC82E011BC6AC6C1F093D351, xmp.iid:A6C8F54B962BE3118A5184F5FEF5426F, xmp.iid:EF1FFB4B962BE3118A5184F5FEF5426F, xmp.iid:C312D6DA0368E311B6E5F05FFFF9DAFC, xmp.iid:65FF19D60568E311B6E5F05FFFF9DAFC, xmp.iid:8CE8BC190668E311B6E5F05FFFF9DAFC, xmp.iid:5E1CCC380668E311B6E5F05FFFF9DAFC History When : 2011:03:31 09:35:34-05:00, 2011:03:31 09:35:34-05:00, 2011:04:01 09:54:07-05:00, 2011:05:20 11:17:31-05:00, 2013:10:02 14:10:27-05:00, 2013:10:02 14:10:27-05:00, 2013:12:18 11:00:02-06:00, 2013:12:18 11:00:02-06:00, 2013:12:18 11:01:56-06:00, 2013:12:18 11:02:48-06:00 History Software Agent : Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0, Adobe InDesign 7.0 History Changed : /;/metadata, /metadata, /;/metadata, /;/metadata, /;/metadata, /metadata, /metadata, /;/metadata, /;/metadata, /;/metadata Create Date : 2014:01:20 15:54:37-06:00 Modify Date : 2014:01:20 15:54:44-06:00 Metadata Date : 2014:01:20 15:54:44-06:00 Creator Tool : Adobe InDesign CS5 (7.0.4) Page Image Page Number : 1, 2 Page Image Format : JPEG, JPEG Page Image Width : 256, 256 Page Image Height : 256, 256 Page Image : (Binary data 11533 bytes, use -b option to extract), (Binary data 12575 bytes, use -b option to extract) Doc Change Count : 33 Format : application/pdf Producer : Adobe PDF Library 9.9 Trapped : False Page Count : 2 Creator : Adobe InDesign CS5 (7.0.4)EXIF Metadata provided by EXIF.tools