Winlite DIN1001 Portable Multi-functional Speaker User Manual D IN User Guide 2011 11 24

Download:
Mirror Download [FCC.gov]
Document ID	1631804
Application ID	N0qGgJAPiaTWzYl2xox7DQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	2.75kB (34391 bits)
Date Submitted	2012-02-07 00:00:00
Date Available	2012-02-21 00:00:00
Creation Date	2011-12-30 14:45:32
Producing Software	GPL Ghostscript 8.15
Document Lastmod	2011-12-30 14:45:32
Document Title	Microsoft Word - D-IN User Guide 2011-11-24.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	Xiaohe_Wang

User Guide (D-IN Bluetooth Speaker)
Technical Spec.:
Input Voltage: 5-5.5V,
Built-in Lithium battery: 3.7V, 1000MA
Power: 3W*2
How to Use
Six Buttons: PLAY
PREV
NEXT
VOL-
VOL+
MODE
4 working modes, the sequence of playing mode by default is listed as below:
BLUETOOTH
AUX
USB/SDcard
（ switch between these four modes with “M” button ）
** Charging the Battery
1.To charge the D-IN BT Speaker, connect the DC plug on the included USB
Power Cable to the Power input located on the back of the speaker.
2.Connect the USB end to a powered USB port.
CAUTIION
Please be noted that the input voltage can’t be over 5.5V or below 5V.
The speaker can’t be charged if the input voltage is too low; the speaker will be
damaged if the input voltage is too high.
Remark: the LED on the bottom will turn red while the speaker is being charged,
and the LED light will be off after full charge.
** POWER ON/OFF
Turn on the D-IN BT Speaker by pressing the ON/OFF button located on the top of
the speaker. D IN is automatically in Bluetooth mode when it’s an ON mode, and the
Blue LED for Bluetooth will flash first and later keep on. Then the Bluetooth
module start working..
**Playing music via Bluetooth mode
1.Connect the speaker with the Bluetooth-enabled devices in the 1st time, the Blue
LED light will keep flashing for searching the BT signal.
If it’s not the 1st time for the speaker to work with Bluetooth-enabled devices, when
it’s on BT mode, the blue LED light will keep on in a few seconds after flashing, at
this moment the D-IN BT speaker is trying to connect the memorial
Bluetooth-enabled device. Once it’s done, the LED will flash slowly, but if it’s failed,
after 5 seconds the BT indicator will flash, waiting for the connection with new
device, then follow the steps as below
2. Ensure Bluetooth-enabled devices has Bluetooth switched on and begin searching
for devices, select the “ bluSound ” device and if a password is required
enter “0000”.When the blue LED flashes slowly, the pairing with Bluetooth-enabled
devices has been completed
3.Press the play button on the top of speaker or click the play button on the
Bluetooth-enabled device, then you can enjoy the music via BT.
Remark:
1.We can control the Bluetooth-enabled devices through PLAY,PAUSE,TRACK
Buttons on the top of speaker, but it needs the related software of Bluetooth-enabled
devices to support, currently it can work with most of mobiles with Android system
and the computer with TT player, Kugoo.
2.When we turn off the D-IN speaker and restart, the speaker will search the device
connected last time automatically. But it also need the related software of
Bluetooth-enabled devices to support. If connect it with new device, power on the
speaker and wait 20 seconds. The blue LED will flash，then research the new device
**Play music Via AUX
mode
1. Connect the D-IN BT Speaker to the audio device using audio cable
2. Press MODE button and adjust to LINE(AUX), green LED will turn on.
3. Use the volume control on the top of speaker and adjust to your desired volume.
4. USE the PLAY button to adjust to mute.
5. Other buttons have no function on AUX mode.
** Play the music via USB Flash Disk or SD Card mode
1. Insert the USB Flash Disk or SD Card into the USB port on the D-IN speaker ,
press MODE button and adjust to USB/SD mode, yellow LED will turn on
2. The yellow LED will keep flashing when play music, if pause, the yellow LED
will keep on.
3.Use the play button to pause the music, use the PREV and NEXT button to play
the desired music, if you need a fast backward search, please press the PREV button
continuely if you need a fast forward search, please have one continual press on the
NEXT button.
3.Use the volume control on the top of speaker and adjust to your desired volume.
**Play music Via AUX OUT mode
Insert the 3.5mm audio cable into the AUX-OUT jack on the D-IN speaker, the
speaker will stop voice export, and change to AUX OUT mode automatically. Then
you can connect with high power equipment and enjoy the music with different
format via D-IN .
LED Indicator
** Working indicator on the top of speaker
3- color LED: blue, green, yellow
Blue LED: Bluetooth mode
Green LED:
AUX mode
Yellow LED: SD/USB mode
** Charging indicator on the bottom of speaker
Single color LED: Red
The red LED will be on when the speaker is being charged;
The red LED will be off when the speaker is fully charged
FCC Conformity:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for
help.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
Page Count                      : 5
Create Date                     : 2011:12:30 14:45:32
Title                           : Microsoft Word - D-IN User Guide  2011-11-24.doc
Producer                        : GPL Ghostscript 8.15
Author                          : Xiaohe_Wang
Creator                         : PScript5.dll Version 5.2
Modify Date                     : 2011:12:30 14:45:32

EXIF Metadata provided by EXIF.tools