Wistron NeWeb DHUBW69 802.11 abgn/ac 2x2 module with BT User Manual WLAN a b g Cardbus Adapter

Download:
Mirror Download [FCC.gov]
Document ID	2901863
Application ID	0p0FTExaojEMkvnMJy4puw==
Document Description	User manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	50.34kB (629265 bits)
Date Submitted	2016-02-12 00:00:00
Date Available	2016-02-15 00:00:00
Creation Date	2017-11-18 00:53:20
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-11-18 00:53:20
Document Title	WLAN a+b+g Cardbus Adapter
Document Creator	Microsoft® Word 2010
Document Author:	Vicky Lin

Wireless LAN Module
(802.11 abgn/ac 2x2 module with BT)
WNC / DHUB-W69
User Manual
Copyright Statement
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any
form or by any means, whether electronic, mechanical, photocopying, recording or otherwise
without the prior writing of the publisher.
Pentium is trademark of Intel.
All copyright reserved.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Country Code selection feature to be disabled for products marketed to the US/CANADA
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna
and users, and
2) The transmitter module may not be co-located with any other transmitter or antenna,
3) For all products market in US, OEM has to limit the operation channels in CH1 to
CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply
any tool or info to the end-user regarding to Regulatory Domain change.
As long as 3 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed
IMPORTANT NOTE
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
TheΝfinalΝendΝproductΝmustΝbeΝlabeledΝinΝaΝvisibleΝareaΝwithΝtheΝfollowing:Ν“ContainsΝFCCΝ
ID: NKR-DHUBW69.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding
howΝtoΝinstallΝorΝremoveΝthisΝRFΝmoduleΝinΝtheΝuser’sΝmanualΝofΝtheΝendΝproductΝwhichΝ
integrates this module.
The end user manual shall include all required regulatory information/warning as show in
this manual.
Industry Canada statement:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.
This device is intended only for OEM integrators under the following conditions: (For
module device use)
1) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 1 condition above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions
suivantes: (Pour utilisation de dispositif module)
1) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 1 conditions ci-dessus sont remplies, des essais supplémentaires sur
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours
responsable des essais sur son produit final pour toutes exigences de conformité
supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the Canada authorization is
no longer considered valid and the IC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines
configurations d'ordinateur portable ou de certaines co-localisation avec un autre
émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut
pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé
de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation
distincte au Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final
end product must be labeledΝ inΝ aΝ visibleΝ areaΝ withΝ theΝ following:Ν “ContainsΝ IC:
4441A-DHUBW69 ”.Ν
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où
l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue
entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible
avec l'inscription suivante: "Contient des IC: 4441A-DHUBW69".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding
howΝtoΝinstallΝorΝremoveΝthisΝRFΝmoduleΝinΝtheΝuser’sΝmanualΝofΝtheΝendΝproductΝwhichΝ
integrates this module.
The end user manual shall include all required regulatory information/warning as show in
this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur
final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de
l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises
et avertissements comme indiqué dans ce manuel.
Caution:
(i) the device for operation in the band 5150–5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems;
(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the
equipment still complies with the e.i.r.p. limit;
(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the band 5725-5850 MHz shall be such that the equipment still complies with
the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as
appropriate; and
Operations in the 5.25-5.35GHz band are restricted to indoor usage only.
Avertissement:
(i) les dispositifs fonctionnant dans la bande de 5150 à 5250MHz sont réservés
uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage
préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux;
(ii) pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne permis
pour les dispositifs utilisant les bandes de 5250 à 5350MHz et de 5470 à 5725 MHz doit
être conforme à la limite de la p.i.r.e;
(iii) pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne permis
(pour les dispositifs utilisant la bande de 5725 à 5850 MHz) doit être conforme à la limite
de la p.i.r.e. spécifiée pour l'exploitation point à point et l'exploitation non point à point,
selon le cas;
Antenna information for BT
Antenna
Model
Peak gain (dBi)
Type
Connector
2400~2483.5MHz
DHUB-W69_BT_81.EEW15.GLC
PIFA
IPEX
-1.45
DHUB-W69_BT_81.EEW15.GLE
PIFA
IPEX
-1.93
DHUB-W69_BT_81.EEW15.GLF
PIFA
IPEX
-2.01
E48u
PIFA
UFL
1.41
E55u
PIFA
UFL
2.51
M55
PIFA
UFL
2.61
M65
PIFA
UFL
2.01
Antenna information
Antenna
Peak gain ( dBi )
for Wi Fi
Model
Type Connector 2400 ~ 2483.5MHz 5150 ~ 5250MHz 5250 ~ 5350MHz 5470 ~ 5725MHz 5725 ~ 5850MHz
on board antenna
PIFA
N/A
2.14
3.8
4.4
4.8
3.3
E48u – Black
PIFA
U.FL
2.51
3.62
3.68
3.18
2.06
E48u - Withe
PIFA
U.FL
2.11
2.92
2.98
2.48
1.36
E55u - Black
PIFA
U.FL
2.11
3.02
3.08
2.58
1.46
E55u - Withe
PIFA
U.FL
2.61
3.82
3.88
3.38
2.26
M55 - Black
PIFA
U.FL
-0.72
2.55
2.83
2.66
2.9
M55 - Withe
PIFA
U.FL
-0.22
3.45
3.73
3.56
3.8
M65 - Black
PIFA
U.FL
1.11
1.12
1.18
0.68
-0.44
M65 - Withe
PIFA
U.FL
1.81
2.32
2.38
1.88
0.76
Europe – EU Declaration of Conformity
This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The
following test methods have been applied in order to prove presumption of conformity with the
essential requirements of the R&TTE Directive 1999/5/EC:
EN60950-1:2006+A11:2009+A1:2010+A12:2011
IEC60950-1:2005 (2nd Edition); Am 1:2009
Safety of Information Technology Equipment
EN 62311: 2008 / Article 3(1)(a) and Article 2 2006/95/EC)
Assessment of electronic and electrical equipment related to human exposure restrictions for
electromagnetic fields (0 Hz-300 GHz)
EN 300 328 V1.9.1: 2012-06
Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission
systems; Data transmission equipment operating using wide band modulation techniques;
Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
EN 301 893 V1.8.1: 2012-06
Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN
covering the essential requirements of article 3.2 of the R&TTE Directive
EN 301 489-1 V1.9.2: 2011
Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic
Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical
requirements
EN 301 489-17 V2.2.1 2012
Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC)
standard for radio equipment; Part 17: Specific conditions for Broadband Data Transmission Systems
EN 300 440
In Italy the end-user should apply for a license at the national spectrum authorities in order to
obtain authorization to use the device for setting up outdoor radio links and/or for supplying public
access to telecommunications and/or network services.
ČeskyΝ
[Czech]
Dansk
[Danish]
[Jméno výrobce] tímtoΝprohlašuje,ΝžeΝtentoΝ[typ zařízení] jeΝveΝshoděΝseΝzákladnímiΝ
požadavkyΝaΝdalšímiΝpříslušnýmiΝustanovenímiΝsměrniceΝ1λλλ/5/ES.
Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets
typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF.
Deutsch
[German]
Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in
Übereinstimmung mit den grundlegenden Anforderungen und den übrigen
einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Eesti
[Estonian]
Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type
of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist
tulenevatele teistele asjakohastele sätetele.
English
Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance
with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Español
[Spanish]
Por medio de la presente [nombre del fabricante] declara que el [clase de equipo]
cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o
exigibles de la Directiva 1999/5/CE.
ζζηνδεήΝ
[Greek]
Μ ΝΣΗΝΝΠΑΡΟΤ΢Α [name of manufacturer] ΗΛΩΝ ΙΝΟΣΙ [type of equipment]
΢ΤΜΜΟΡΦΩΝ ΣΑΙΝΠΡΟ΢ΝΣΙ΢ΝΟΤ΢ΙΩ
Ι΢ΝΑΠΑΙΣΗ΢ Ι΢ΝΚΑΙΝΣΙ΢ΝΛΟΙΠ ΢Ν΢Χ ΣΙΚ ΢Ν
ΙΑΣΑΞ Ι΢ΝΣΗ΢ΝΟ ΗΓΙΑ΢Ν1λλλ/5/ Κ.
Français
[French]
Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme
aux exigences essentielles et aux autres dispositions pertinentes de la directive
1999/5/CE.
Italiano
[Italian]
Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva
1999/5/CE.
Latviski
[Latvian]
ArΝšoΝ[name of manufacturer / izgatavotāja nosaukums] deklarē,ΝkaΝ[type of equipment
/ iekārtas tips] atbilstΝDirektīvasΝ1λλλ/5/EKΝbūtiskajāmΝprasībāmΝunΝcitiemΝarΝtoΝ
saistītajiemΝnoteikumiem.
LietuviųΝ
[Lithuanian]
Nederland
s [Dutch]
ŠiuoΝ[manufacturer name] deklaruoja,ΝkadΝšis [equipment type] atitinka esminius
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in
overeenstemming is met de essentiële eisen en de andere relevante bepalingen van
richtlijn 1999/5/EG.
Malti
Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma
[Maltese]
mal-ħtiġijietΝessenzjaliΝuΝmaΝprovvedimentiΝoħrajnΝrelevantiΝliΝhemmΝfid-Dirrettiva
1999/5/EC.
Magyar
[Hungarian]
Polski
[Polish]
Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Niniejszym [nazwa producenta] oświadcza,ΝżeΝ[nazwa wyrobu] jest zgodny z
zasadniczymiΝwymogamiΝorazΝpozostałymiΝstosownymiΝpostanowieniamiΝDyrektywyΝ
1999/5/EC.
Português
[Portuguese]
Slovensko
[Slovenian]
Slovensky
[Slovak]
Suomi
[Finnish]
[Nome do fabricante] declara que este [tipo de equipamento] está conforme com os
requisitos essenciais e outras disposições da Directiva 1999/5/CE.
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in
ostalimiΝrelevantnimiΝdoločili direktive 1999/5/ES.
[Meno výrobcu] týmtoΝvyhlasuje,ΝžeΝ[typ zariadenia] spĺňaΝzákladnéΝpožiadavkyΝaΝvšetkyΝ
príslušnéΝustanoveniaΝSmerniceΝ1λλλ/5/ES.
[Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen
tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä
koskevien direktiivin muiden ehtojen mukainen.
10
Taiwan 警語
第十二條→經型式認證合格之低 率射頻電機，非經許
自變更頻率
大 率或變更原設計之特性及 能
第十四條→低 率射頻電機之使用不得影響飛航安
時，應立即停用，並改善至無 擾時方得繼續使用
前項合法通信，指依電信法規定作業之無線電通信
業 科學及醫療用電波輻射性電機設備之 擾
及
低
，公司，商
或使用者均不得擅
擾合法通信；經發現有
率射頻電機須忍
擾現象
合法通信或工
無線傳輸設備 (UNII)
在 5.25-5.35 秭赫頻帶 操作之無線資訊傳輸設備，限於室
無線資訊傳輸設備忍 合法通信之 擾且不得
俟無 擾之 ，始得繼續使用
(4.7.6)
使用
擾合法通信；如造成
(4.7.5)
擾，應立即停用，
無線資訊傳設備的製造廠商應確保頻率穩定性，如依製造廠商使用手冊上所述正常操作，
發射的信 應維持於操作頻帶中 (4.7.7)
Note: 1. 本模組於
上標示
本產品
得認證後將依規定於模組本體標示審驗合格標籤 2. 系統廠商應於
含射頻模組:
CCXXxxYYyyyZzW
11
字樣.
Table of Contents
1. INTRODUCTION
2. DRIVER/UTILITY INSTALLATION / UNINSTALLATION
3. CONNECTING TO AN EXISTING NETWORK
4. MODIFYING A WIRELESS NETWORK
4.1 MODIFYING GENERAL SETTINGS ................................................................................................
4.2 MODIFYING SECURITY SETTINGS ................................................................................................
12
1. INTRODUCTION
Thank you for purchasing the 802.11 a/b/g/n /ac and Bluetooth Combo module that provides the
easiest way to wireless networking. This User Manual contains detailed instructions in the
operation of this product. Please keep this manual for future reference.
System Requirements
- 128 MB of RAM or later (recommended)
- 300 MHz processor or higher
2. Driver/Utility Installation
The driver should have been installed before the audio device is shipped from the manufacturer.
You can start using its network function without installing driver or utility.
3. Connecting to an Existing Network
1. Use the remote control that came with your audio device to access the network configuration
settings page.
2. Select the scanning wireless network function. The system starts to scan for available network.
On this list, click Refresh to refresh the list at any time
3. Select the network you want to connect to.
4. If the chosen network has security enabled, you will have to setup corresponding security
parameter. Contact the network manager for the correct settings. Select the security type and
fill in required parameters. The options include the following:

WPA/WPA2/CCKM

WPA/WPA2 Passphrase
802.1x
Pre-Shared Key (Static WEP)
None



13
4. Modifying a Wireless Network
4.1 Modifying General Settings
1. Use the remote control that came with your audio device to access the network configuration
settings page.
2. From the profile list, select one profile and choose the modify function.
3. Modify the settings below for your network.
Profile Name
Identifies the configuration wireless network profile.
This name must be unique. Profile names are not
case sensitive.
Client Name
Identifies the client machine.
Use this profile for
Access Point mode
Configures station to operate in Access Point mode.
Network Names
(SSIDs)
The IEEE 802.11 wireless network name. This field
has a maximum limit of 32 characters. Configure up
to three SSIDs (SSID1, SSID2, and SSID3).
14
4.2 Modifying Security Settings
1. Use the remote control that came with your audio device to access the network configuration
settings page.
2. Select a security option of this wireless network. This product provides security options below.
Contact your wireless network administrator for choosing a correct option.

WPA/WPA2/CCKM

WPA/WPA2 Passphrase

802.1x
Pre-Shared Key (Static WEP)
None


WPA/WPA2
WPA/WPA2
Passphrase
802.1x
Enables the use of Wi-Fi Protected Access (WPA).
Choosing WPA/WPA2 opens the WPA/WPA2 EAP drop-down menu.
The options include:
 EAP-FAST
 EAP-TLS
 EAP-TTLS
 EAP-SIM
 PEAP (EAP-GTC)
 PEAP (EAP-MSCHAP V2)
 LEAP
Enables WPA/WPA2 Passphrase security.
Click on the Configure button and fill in the WPA/WPA2 Passphrase.
Enables 802.1x security. This option requires IT administration.
Choosing 802.1x opens the 802.1x EAP type drop-down menu. The
options include:







Pre-Shared Key
(Static WEP)
EAP-FAST
EAP-TLS
EAP-TTLS
EAP-SIM
PEAP (EAP-GTC)
PEAP (EAP-MSCHAP V2)
LEAP
Enables the use of pre-shared keys that are defined on both the access
point and the station.
To define pre-shared encryption keys, choose the Pre-Shared Key radio
button and click the Configure button to fill in the Define Pre-Shared
Keys window.
15
None
No security (not recommended).
Allow Association to
Mixed Cells
Check this check box if the access point with which the client adapter is
to associate has WEP set to Optional and WEP is enabled on the client
adapter. Otherwise, the client is unable to establish a connection with
the access point.
Check this check box and enter the number of seconds (up to 300) after
which the authentication process times out when trying to find the
domain controller. Entering zero is like unchecking this check box,
which means no time limit is imposed for finding the domain controller.
Note: The authentication process times out whenever the authentication
timer times out or the time for finding the domain controller is reached.
Limit Time for
Finding Domain
Controller To
Group Policy Delay
Specify how much time elapses before the Windows logon process
starts group policy. Group policy is a Windows feature used by
administrators to specify configuration options for groups of users. The
objective is to delay the start of Group Policy until wireless network
authentication occurs. Valid ranges are from 0 to 65535 seconds. The
value that you set goes into effect after you reboot your computer with
this profile set as the active profile.
This drop-down menu is active only if you chose EAP-based
authentication.
16

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract
Author                          : Vicky Lin
Create Date                     : 2016:02:03 23:01:04+08:00
Modify Date                     : 2016:02:04 11:10:46+08:00
Language                        : zh-TW
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : Vicky Lin
Title                           : WLAN a+b+g Cardbus Adapter
Creator Tool                    : Microsoft® Word 2010
Metadata Date                   : 2016:02:04 11:10:46+08:00
Producer                        : Microsoft® Word 2010
Document ID                     : uuid:0be9d566-b9d5-40e1-89d9-ed9f4e18853d
Instance ID                     : uuid:31849547-5d9c-44e1-934c-5862a9b90979
Page Count                      : 17

EXIF Metadata provided by EXIF.tools