Wistron NeWeb DRCB BCM 4318 CF Module User Manual

Download:
Mirror Download [FCC.gov]
Document ID	615801
Application ID	c8DD4PHmoGIHEhjfxNjzcg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	18.23kB (227848 bits)
Date Submitted	2005-12-29 00:00:00
Date Available	2005-12-29 00:00:00
Creation Date	2005-12-27 20:09:27
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2005-12-29 14:02:44
Document Title	Microsoft Word - DRCB-M1_G_Manual_Eng_V0.1TA_20051219_Jessy3805.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	landy

DRCB-M1
IEEE 802.11 b/g CF WLAN Module
User’s Manual
V0.1 Dec.20, 2005
Table of Contents
Chapter 1 Functional Description ................................................... 5
1.1 Features ............................................................................. 5
1.2 Integrated Radio Transceiver ............................................. 5
1.3 Receiver Path..................................................................... 6
1.4 Transmitter Path ................................................................. 6
1.5 Calibration .......................................................................... 6
Chapter 2 Installation Driver ........................................................... 7
2.1 Driver Features................................................................... 7
2.2 Installing the driver ............................................................. 7
Copyright Statement
No part of this publication may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, whether electronic,
mechanical, photocopying, recording or otherwise without the prior
writing of the publisher.
Windows™ 98SE/2000/ME/XP are trademarks of Microsoft® Corp.
Pentium is trademark of Intel.
All copyright reserved.
FEDERAL COMMUNICATIONS COMMISSION
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiated radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user‘s authority to operate the equipment.
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be
installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module
may not be co-located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM
integrator is still responsible for testing their end-product for any additional compliance requirements
required with this module installed (for example, digital device emissions, PC peripheral requirements,
etc.).
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is no longer considered
valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will
be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization. The antenna cable can only be connected on J2 port.
If the FCC ID is not visible when the module is installed inside another device, then the outside of the
device into which the module is installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains FCC ID: NKRDRCB” .
Chapter 1 Functional Description
Thank you very much for purchasing this IEEE802.11b/g CF WLAN
Module. This product provides the easiest way to wireless networking.
This User Manual contains instructions in the operation of this product.
Please keep this manual for future reference.
1.1 Features
Includes Encore signal processing for Industry-leading receive
sensitivity and extended range:
․-74 dBm at 54Mbps
․-76 dBm with external LNA
High level of integration with direct converseon radio architecture
minimizes external circuitry, leading to lowest cost, lowest power, and
smallest footprint implementation
Flexible support for a variety of system bus interfaces includeing: PCI,
Mini PCI, CardBus, PCMCIA/Compact Flash, and SDIO (4-wire,
1-wire, and SPI)
Programmable data rates of 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and
54 Mbps.
24-bit IV and 40-bit/104-bit key WEP encryption support
System support for 128-bit AES
IEEE802.1x support
Dynamic Power Management under driver control
WHQL-certified drivers for Windows® XP/Me/2000/98SE/98
operating systems
Wi-Fi® compliant
1.2 Integrated Radio Transceiver
This CF module includes an integrated RF transceiver that has been
optimized for use in 2.4-GHz WLAN systems. It has been designed to
provide low-power, low-cost, and robust communications for applications
operating in the globally available 2.4-GHz unlicensed ISM band. With
an external transmit power amplifyier, it develops full output power per
the IEEE802.11b/g Specification.
1.3 Receiver Path
This CF module has a wide dynamic range, direct conversion receiver. It
employs high-order on-chip channel filtering to ensure reliable operation
in the noisy 2.4-GHz ISM band. The excellent noise figure of the receiver
makes an external LNA unnecessary.
Leading-edge Encore DSP technology improves the receive sensitivity
and extended range, that enables whole home coverage.
1.4 Transmitter Path
This CF module includes a linear transmitter capable of delivering up to
+6 dBm while meeting the IEEE802.11g specification. The output power
is adjustable in 0.6-dB steps, down to –15 dBm. Baseband data is
up-converted directly to the 2.4-GHz ISM band.
1.5 Calibration
This CF module enables the device to be used in high-volume
applications because calibration routines are not required during
manufacturing test. These calibration routines are performed periodically
in the course of normal radio operation.
Chapter 2 Installation Driver
This driver is porting from bcm4318 1.130.35.0 with CCX source code to
WinCE NDIS CF interface. This CF driver is workable in Intermec 751
PDA, and CN30 PDA.
2.1 Driver Features
IEEE 802.11b/g
Ad-Hoc / Infrastructure
WEP 64 / 128-bit
WPA-PSK / WPA2-PSK (by WZC / Funk Client)
WPA / WPA2 (by WZC / Func Client)
802.1x – TLS / 802.1x – PEAP (by WZC / Funk Client)
LEAP (by Funk Client)
WPA-TTLS (by Funk Client)
TKIP
AES
IEEE Power Save
IEEE 802.11d
2.2 Installing the driver
Step1. Copy the file, “bcmcf.dll”, into PDA.
Step2. Plug in BCM4318 CF card into system.
Step3. Enter the driver name “bcmcf” in the unknown card dialog.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
About                           : uuid:7c29f194-9bcc-4e69-b76d-6d7e91e5a065
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2005:12:29 14:02:44+08:00
Create Date                     : 2005:12:27 20:09:27+08:00
Metadata Date                   : 2005:12:29 14:02:44+08:00
Document ID                     : uuid:31fb6b14-b224-42b9-9f6e-f14b282fbf22
Instance ID                     : uuid:362d1738-d766-41a7-b472-0c816842c1f4
Format                          : application/pdf
Title                           : Microsoft Word - DRCB-M1_G_Manual_Eng_V0.1TA_20051219_Jessy3805.doc
Creator                         : landy
Has XFA                         : No
Page Count                      : 7
Author                          : landy

EXIF Metadata provided by EXIF.tools