Wistron NeWeb EM500AG 2.4/5GHz Wireless LAN Mini-PCI Card User Manual updated

Download:
Mirror Download [FCC.gov]
Document ID	394852
Application ID	oD6KWcZrllJ3IWOUli9KZA==
Document Description	Users Manual Revised
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	145.8kB (1822472 bits)
Date Submitted	2004-02-06 00:00:00
Date Available	2004-01-28 00:00:00
Creation Date	2004-01-20 18:13:31
Producing Software	Acrobat PDFWriter 4.0 for Windows
Document Lastmod	2004-01-20 18:33:59
Document Title	穨updated.PDF
Document Creator	穨Microsoft Word
Document Author:	穨daphne liu

WLAN 802.11a+b+g Mini-PCI Module
Model
EM-500AG
OEM Installation Manual
1.The OEM integrator couldn’t provide any information
to end user regarding how to remove or install the
device.
2.The module is sold only to the OEM integrators & the
manual is valid only for the OEM manufactures.
3. Changes or modifications to this equipment not
expressly approved by WNC may void the user’s
authority to operate this equipment.
Version: 1.0
Copyright Statement
No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, whether electronic, mechanical,
photocopying, recording or otherwise without the prior writing of the publisher.
Windows™ 98SE/2000/ME/XP are trademarks of Microsoft ® Corp.
Pentium is trademark of Intel.
All copyright reserved.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, (example - use only shielded
interface cables when connecting to computer or peripheral devices) any
changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
IMPORTANT NOTE:
This module is restricted to mobile configuration. To comply with FCC RF
exposure compliance requirements, the antenna used for this transmitter must
be installed to provide a separation distance of at least 20 cm from all persons
and must not be co-located or operating in conjunction with any othe r antenna
or transmitter. This transmitter module must not be co-located or operating in
conjunction with any other antenna or transmitter
Table of Contents
1. INTRODUCTION
1.1 THE WLAN 802.11 A+B+ G MINI-PCI M ODULE .....................................................4
1.2 HARDWARE INSTALLATION & ANTENNA INFORMATION
2. DRIVER/UTILITY INSTALLATION / UNINSTALLATION
2.1 INSTALLATION .........................................................................................................9
2.1.1 ADDITIONAL S ETUP P ROCESSES ...........................................................................12
2.1.2 VERIFYING THE DRIVER .......................................................................................12
2.2 UNINSTALLATION ...................................................................................................14
3. CONNECTING TO AN EXISTING NETWORK 15
3.1 ADDITIONAL NOTE FOR WINDOWS XP ................................................................17
4. CREATING A NEW NETWORK 18
5. CONFIGURATION 20
5.1 DEVICE CONFIGURATION ......................................................................................20
5.1.1 NON-DEFAULT SETTINGS CONFIGURATION ..........................................................21
5.1.2 DEFAULT S ETTINGS WINDOWS XP ZERO-CONFIGURATION .................................24
1. Introduction
1.1 The WLAN 802.11a+b+g mini-PCI Module
Thank you for purchasing the WLAN a+b+g mini-PCI Module that provides the
easiest way to wireless networking. This Manual contains detailed instructions in
the operation of this product. Please keep this manual for future reference.
1.2 Hardware Installation & Antenna Information
Module is installed in the Personal Computer, located either under the
keypad or on the bottom side of the Personal Computer (see the following
diagrams).
l
Antennas are embedded in the two sides of the panel (see the two antennas
shown below)
Only the DT3 antenna
can be used.
Important Note:
This module is restricted to mobile configuration. The antennas of module
should be installed and operated with minimum distance 20cm between the
radiator and all persons. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
The module is for OEM installation only and can not be sold to end user directly.
*Caution !!
(1). This module cannot be bound in a tablet computer
for RF exposure issues. (See label 1)
(2). Due to the RF exposure issues, this module can be
used in a laptop computer in normal operation, but
cannot be used when it is put above the lap and the
LCD screen is in the closed position. (See label 2)
The device can’t be operated above
the lap when the LCD is closed
Label 1
Label 2
(3). This module must be labeled with FCC ID. (See
label 3)
Label 3
(4). If the FCC ID is not visible when the module is
installed inside another device, then the outside of
device must also display a label referring to the
enclosed module. The exterior label can be “ Contains
Transmitter Module FCC ID: NKREM500AG” or similar
wording. (See label 4)
Label 4
Please put Label 2 & Label 4 to the enclosure of end
product to note the end user.
(5). The user manual for end users must include the following
information in a prominent location.
“ IMPORTANT NOTE: To comply with FCC RF exposure
compliance requirements, the antenna used for this
transmitter must be installed to provide a separation distance
of at least 20 cm from all persons and must not be co-located
or operating in conjunction with any other antenna or
transmitter.”
2. Driver/Utility Installation / Uninstallation
2.1 Installation
Note! The Installation Section in this User Manual describes the first-time installation
for Windows. To re-install the driver, please first uninstall the previously
installed driver. See Chapter 2.2 “Uninstallation” section in this User Manual.
Follow the steps below to complete the driver/utility installation:
1. Insert the Installation Software CD into the CD-Rom Drive.
2. Click “Next”.
3. Read the License Agreement and click “Yes”.
4. Click “Next” to continue or click “Browse” to choose a destination folder.
5. Click “Next”.
10
6. Click “Yes” to create a shortcut icon on your desktop.
7. Click “Finish”.
8. You should now see the shortcut icon on your desktop.
11
2.1.1 Additional Setup Processes
During software installation procedure, each operating system may prompt different
specific options:
1. Windows 98SE: The system will request the original Windows CD during the
installation process. When the installation is finished, you’ll have to restart your
computer.
2. Windows Me: Please restart your computer when the installation is finished.
3. Windows 2000/XP: Select “Install the software automatically” when the window
with this option appears, and then click “Next” to continue installation.
2.1.2 Verifying the Driver
1. Windows 98SE/Me:
Step 1. Right-click “My Computer” icon on the desktop and choose “Properties”.
Step 2. Select “Device Manager” tab and open “Network adapters”. You should
see your WLAN a+b+g mini-PCI Module in the list. Highlight it and click
“Properties” button.
Step 3. From the “Device status”, you should see the line “This device is working
properly”. If, instead, you see error messages displayed, please remove
this Adapter (highlight this Adapter and click “Remove” button). Restart
your PC and go through the installation process again.
2. Windows 2000:
Step 1. Right-click “My Computer” icon on the desktop and choose “Properties”.
Step 2. Select “Hardware” tab and click “Device Manager”. Open “Network
adapters”. You should see your WLAN a+b+g mini-PCI Module in the list.
Right-click this Adapter and choose “Properties”.
Step 3. From the “Device status”, you should see the line “This device is working
properly”. If, instead, you see error messages displayed, please uninstall
this Adapter (right-click this Adapter from the “Network adapters” list and
choose “Uninstall”). Restart your PC and go through the installation
process again.
12
3. Windows XP:
Step 1. Click Start>Control Panel> System.
Step 2. Select “Hardware” tab, and click “Device Manager”. Open “Network
adapters”. You should see your WLAN a+b+g mini-PCI Module in the list.
Right-click this Adapter and choose “Properties”.
Step 3. From the “Device status”, you should see the line “This device is working
properly”. If, instead, you see error messages displayed, please uninstall
this Adapter (right-click this Adapter from the “Network adapters” list and
choose “Uninstall”). Restart your PC and go through the installation
process again.
13
2.2 Uninstallation
Note! Before uninstallation, please close all running programs.
1. Click Start>Programs>WLAN a+b+g mini-PCI Module>UnInstall WLAN a+b+g
mini-PCI Module.
2. Choose “Remove”. Click “Next”.
3. Click “OK” to start Uninstall.
4. Click “Finish”.
Uninstall is now completed.
14
3. Connecting to an Existing Network
1. Double click the shortcut icon of “WLAN a+b+g mini-PCI Module” on the
desktop, and the “WLAN a+b+g mini-PCI Module Configuration” window will
appear.
2. Click “Refresh” button
, and all available networks will be listed.
15
3. From the list of “Available Networks”, choose one network by double clicking the
Network Name . One of the following dialog boxes appears. Click “Yes” to
continue.
4. If the WEP of the chosen network is enabled, the “Security Setting” tab is
displayed. Enter the correct Encryption Keys and click “OK”. You need to
contact the network administrator for the values the Encryption Keys.
8. Once connected (when you see the icon
or
in front of the name of the
Connected Network), you can check the signal strength from the icon
in the
Windows System Tray.
16
3.1 Additional Note for Windows XP
In Windows XP, it is recommended that you use the WLAN a+b+g mini-PCI Module
Configuration Utility. Before using the Utility, please follow the steps below to
disable the Windows XP Zero Configuration:
Option 1:
1. Double click the shortcut icon
to open the Utility.
2. From the Windows System Tray, you should see the signal icon. Right-click it
and select “Disable Zero-Configuration”.
Option 2:
1. Go to “Control Panel” and double click “Network Connections”.
2. Right-click “Wireless Network Connection” of “WLAN a+b+g mini-PCI Module”,
and select “Properties”.
3. Select “Wireless Networks” tab, and uncheck the check box of “Use Windows to
configure my wireless network settings”, and then click “OK”.
17
4. Creating a New Network
1.
In “WLAN a+b+g mini-PCI Module Configuration” window, click “New”
2. Select the “Profile Editor” tab and check the check box of “Enable Advanced
Setting” to edit all settings. Click “OK” to save the settings.
18
..
3. Click the “Security Setting” tab and set the Encryption Keys. Click “OK” to save
the settings. When you are creating an Infrastructure mode and IEEE802.11b
standard network, please enter a passkey in “Shared Keys: First” field. For
Infrastructure mode and IEEE802.11a standard network, you may enter a
passkey in either “Unique Key” field or “Shared Keys: First” field. If you are
creating an Ad-Hoc mode network, enter a passkey in “Shared Keys: First”
field.
4. The new Network Name is then listed in the Profile List.
Note! For details of each setting, please read Chapter 5 “Configuration”.
19
5. Configuration
5.1 Device Configuration
You can set the Wireless Network Adapter to work in either “infrastructure” mode or
“ad hoc” mode.
Infrastructure Mode
In infrastructure mode, devices communicate with each other by first going through
an Access Point (AP). Wireless devices can communicate with each other or can
communicate with a wired network. When one AP is connected to wired network
and a set of wireless stations, it is referred to as a BSS (Basic Service Set).
Ad Hoc Mode
Ad-hoc mode is also called “peer-to-peer mode” or “Independent Basic Service Set
(IBSS)”. In ad hoc mode, devices communicate directly with each other without
using an Access Point (AP).
20
5.1.1 Non-Default Settings Configuration
1. Open “WLAN a+b+g mini-PCI Module Configuration” by double clicking the
shortcut icon on the desktop.
Note! If there’s no network name listed in the “Profile List”, click “Refresh”
button and double click a Network Name from “Available Networks”.
The chosen Network Name will then be listed in the Profile List.
2. From the Profile List, select one Profile and click “Modify” button
3. Select “Profile Editor” tab and edit the settings. Click “OK” to save the
modifications.
21
n
Configuration Name: This name identifies the configuration. This name
should be unique.
Network Name (SSID): The name of the wireless network. This name
cannot be longer than 32 characters. If the field is set to be “ANY” or is
left blank, your computer will connect to an AP with the best signal
strength.
Network Connection: Specifies the mode of the network. Two options
are “Infrastructure” and “Ad Hoc”.
Power Saving: Three power management options are “Off”, “Normal” and
“Maximum”. In Ad Hoc mode, Power Savings function cannot be enabled.
Wireless Mode: Three options are “802.11b”, “802.11a” or “Auto”.
“Auto” allows the use of either 802.11a or 802.11b mode.
Ad Hoc Net Start: Specifies a band to establish an Ad Hoc network if no
matching SSID is found. Four options are available: 802.11b, 802.11a,
802.11aTurbo and 802.11g (Pure g).
802.11a Turbo: Disables or enables the 802.11a Turbo mode.
802.11b Range: Two options are “Normal Range” and “Extended Range”.
Encryption Type: Three options are “WEP”, “AES” and “Auto”. WEP
stands for Wired Equivalent Privacy, and AES stands for Advanced
Encryption Security. AES provides much higher level of security. “Auto”
allows the Adapter and AP to negotiate the encryption type. If AES is not
available, WEP is used. By default, the Adapter is set to “Auto” and will
attempt to use AES first. If the AP supports WEP only or is configured for
WEP only, the Adapter will automatically use WEP.
Scan Mode: Three options are “Active Scan”, “Passive Scan” and “Auto”.
Transmit Power: Five options are “Full Power”, “50% Power”, “25%
Power”, “12% Power” and “Lowest Power”.
QoS: Stands for Quality of Service. Disables or enables the Adapter to
cooperate in a network using QoS.
Country: Select the country where you are. Different countries have
different regulations. Please do not illegally use the un-licensed channel.
2.4 GHz Preamble: Allows Ad Hoc compatibility with other 2.4 GHz
devices. Two options are “Short and Long” and “Long only”.
22
4. Select “Security Setting” tab and edit the settings. Click “OK” to save the settings.
Enable Security: Enables the WEP security when the check box is checked,
and disables the WEP security when the check box is cleared.
Default Encryption Key: Allows you to choose one type of encryption key
to be used (Unique, First, Second, Third, or Fourth) from the drop down
menu.
Unique Key: Defines the unique encryption key for security for the current
network configuration. Not used in Ad-Hoc mode. To use Unique Key for
security, this field should be populated. To use AES, you must specify a
Unique Key.
Shared Keys: Defines four shared encryption keys. To use Shared Keys
for security, at least one Shared Key should be populated.
Key Length: Defines the length of each encryption key. When the length is
changed to be a smaller number after a key is entered, the key is
automatically truncated to fit. If the length is increased again, the key will
not be automatically updated to the previous value.
23
5. Select “TCP/IP Property” tab. Enter the settings and click “OK” to save the
settings.
If the network uses DHCP server, choose “Obtain an IP address automatically”.
If the network does not use DHCP server, choose “Use the following IP address”
to set the relative settings. For the IP configuration information, please contact
the network administrator.
5.1.2 Default Settings Windows XP Zero-Configuration
You may also choose the default parameters and directly proceed to Windows XP
zero-configuration through the steps below:
1. Go to “Control Panel” and open “Network Connections”.
2. Right-click the Wireless Network Connection of “WLAN a+b+g mini-PCI
Module”, and make sure this connection is Enabled.
3. Right-click the Wireless Network Connection of “WLAN a+b+g mini-PCI
Module”, and then click “Properties”.
4. Select “Wireless Networks” tab and select “Use Windows to configure my
wireless network settings” check box.
Note! Clear the check box of “Use Windows to configure my wireless network
settings” will disable automatic wireless network configuration.
24

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Creator                         : .穨.Microsoft Word
Create Date                     : 2004:01:20 18:13:31
Title                           : .穨.updated.PDF
Author                          : .穨.daphne liu
Producer                        : Acrobat PDFWriter 4.0 for Windows
Modify Date                     : 2004:01:20 18:33:59+08:00
Page Count                      : 25

EXIF Metadata provided by EXIF.tools