Wistron NeWeb P2 Bluetooth Adaptor User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3169459
Application ID	9+KoCA1Mj5txO4O8S8Vt6w==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	32.44kB (405513 bits)
Date Submitted	2016-10-20 00:00:00
Date Available	2016-10-21 00:00:00
Creation Date	2017-12-16 14:28:09
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-12-16 14:28:09
Document Title	Users Manual
Document Creator	Microsoft® Word 2010
Document Author:	WNC

DBUB-P2
Bluetooth Adapter
User’s Manual
This document provides safety instructions and describes the specifications. Read
this document carefully before installing to ensure your safety and product
performance.
Federal Communication Commission (FCC)
Interference Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this
equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Country Code selection feature to be disabled for products marketed to the
US/CANADA.
Operation of this device is restricted to indoor use only
This device is intended only for OEM integrators under the following
conditions:
1.
The antenna must be installed such that 20 cm is maintained between the
antenna and users, and
2.
The transmitter module may not be co-located with any other transmitter or
antenna,
3.
For all products market in US, OEM has to limit the operation channels in CH1
to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not
supply any tool or info to the end-user regarding to Regulatory Domain
change.
As long as 3 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for
any additional compliance requirements required with this module installed
IMPORTANT NOTE
In the event that these conditions can not be met (for example certain laptop
configurations
or
co-location
with
another
transmitter),
then
the
FCC
authorization is no longer considered valid and the FCC ID can not be used on the
final product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a
separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users. The final end product must be labeled in a visible area with the following:
“Contains FCC ID: NKR-P2”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as
show in this manual.
Antenna information
Type
Connector
Peak Gain(dBi)
PIFA
NO
2.68
Industry Canada statement:
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
1) l’appareil ne doit pas produire de brouillage;
2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d’en compromettre le fonctionnement.
Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme Canada limites d'exposition aux radiations dans un
environnement non contrôlé. Cet équipement doit être installé et utilisé à distance
minimum de 20cm entre le radiateur et votre corps.
This device is intended only for OEM integrators under the following
conditions:
1) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 1 condition above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for
any additional compliance requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les
conditions suivantes:
1) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou
antenne.
Tant que les 1 condition ci-dessus sont remplies, des essais supplémentaires sur
l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours
responsable des essais sur son produit final pour toutes exigences de conformité
supplémentaires requis pour ce module installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the Canada
authorization is no longer considered valid and the IC ID can not be used on the
final product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a
separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour
certaines configurations d'ordinateur portable ou de certaines co-localisation avec
un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et
l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances,
l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur)
et l'obtention d'une autorisation distincte au Canada.
End Product Labeling
The final end product must be labeled in a visible area with the following:
“Contains IC: 4441A-P2”.
Plaque signalétique du produit final
Le produit final doit être étiqueté dans un endroit visible avec l'inscription
suivante: "Contient des IC: 4441A-P2".
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as
show in this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à
l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le
manuel de l'utilisateur du produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires
requises et avertissements comme indiqué dans ce manuel.
Antenna information
Type
Connector
Peak Gain(dBi)
PIFA
NO
2.68
Taiwan statement:
第十二條
經型式認證合格之低
率射頻電機，非經許可，公司
商號或使用者均不得擅自變更頻率
大 率或變更原設計之特性及 能
第十四條
低
率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停
用，並改善至無干擾時方得繼續使用
低
前項合法通信，指依電信法規定作業之無線電通信
率射頻電機須忍受合法通信或工業 科學及醫療用電波輻射性電機設備之干擾
Información México
“La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es
posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este
equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda
causar su operación no deseada.”
Caution:
Be aware of the following limits before using the Bluetooth Adaptor.

Do not subject the Bluetooth Adaptor to high temperatures, direct sunlight or
moisture.

Do not bend, or subject the Bluetooth Adaptor to strong impacts.

Do not disassemble or alter the Bluetooth Adaptor in any way.

Do not attempt to install the Bluetooth Adaptor in any incompatible device.

Do not remove the Bluetooth Adaptor from the TV’s during operations.

Data transmitted and received over radio waves may be intercepted and
monitored.

To avoid malfunctions caused by radio wave interface, keep the TV away from the
devices such as other wireless devices, microwaves and the devices that use 2.4
GHz signals when using the Bluetooth Adaptor.

Depending on the area, this Bluetooth Adaptor may not be available.
Setup the Bluetooth connection
The Bluetooth adapter is pre-installed in the TV set. No extra installation steps are
required for users. Follow the steps below to start using the feature of this
adapter:
1. Turn on your TV.
2. Switch to the channel that delivers 3D contents. If you are watching a disc with
3D contents, you will also need to activate your player for playing the disc.
3. Turn on your 3D glasses.
4. The 3D glasses will pair with this Bluetooth adapter automatically and are now
ready for use.
Specification
Item
Contents
Frequency range:
2402-2480MHz
Channel spacing:
1MHz
Channel List:
79 channels
Modulation type:
GFSK, π/4 – DQPSK, 8DPSK
Modulation technology:
GFSK
Conducted output power:
10dBm
Antenna type:
PIFA antenna
Antenna gain(dBi):
2.68
Antenna connector:
NA
Operating temperature:
0~60℃
Power supply
3.3Vdc from host
* Transfer rate are theoretical values; however, actual communication rate will
vary according to communication environment or connected equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 1
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:bd7c88f0-a920-11f2-0000-02c7314339d4
Producer                        : GPL Ghostscript 9.18
Modify Date                     : 2017:07:25 06:40:47Z
Create Date                     : 2017:07:25 06:40:47Z
Creator Tool                    : UnknownApplication
Document ID                     : uuid:bd7c88f0-a920-11f2-0000-02c7314339d4
Format                          : application/pdf
Title                           : Untitled

EXIF Metadata provided by EXIF.tools