Wistron NeWeb P75B Wireless LAN Adaptor User Manual WLAN a b g Cardbus Adapter
Wistron NeWeb Corporation Wireless LAN Adaptor WLAN a b g Cardbus Adapter
User manual
Wireless LAN Adaptor (11abgn 2x2 USB) Panasonic DNUA-P75B User Manual Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Pentium is trademark of Intel. All copyright reserved. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/CANADA Operation of this device is restricted to indoor use only This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final endΝproductΝmustΝbeΝlabeledΝinΝaΝvisibleΝareaΝwithΝtheΝfollowing:Ν“ContainsΝFCCΝID: NKR-P75B”. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding howΝtoΝinstallΝorΝremoveΝthisΝRFΝmoduleΝinΝtheΝuser’sΝmanualΝofΝtheΝendΝproductΝwhichΝ integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Industry Canada statement: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Caution: (i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; (ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and (iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. (iv) Users should also be advised that high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement: (i) les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pourΝuneΝutilisationΝàΝl’intérieurΝafinΝdeΝréduireΝles risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux; (ii)ΝleΝgainΝmaximalΝd’antenneΝpermisΝpourΝlesΝdispositifsΝutilisantΝlesΝbandesΝ5Ν250-5 350 MHz et 5 470-5 725 MHz doit se conformer à la limite de p.i.r.e.; (iii)ΝleΝgainΝmaximalΝd’antenneΝpermisΝ(pourΝlesΝdispositifsΝutilisantΝlaΝbandeΝ5Νι25-5 825 MHz)ΝdoitΝseΝconformerΝàΝlaΝlimiteΝdeΝp.i.r.e.ΝspécifiéeΝpourΝl’exploitationΝpointΝàΝpointΝetΝ non point à point, selon le cas. (iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d.,Νqu’ilsΝontΝlaΝpriorité)ΝpourΝ les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: 1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre l'antenne et les utilisateurs, et 2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE: Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final endΝ productΝ mustΝ beΝ labeledΝ inΝ aΝ visibleΝ areaΝ withΝ theΝ following:Ν “ContainsΝ IC: 4441A-P75B”.Ν Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 4441A-P75B". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding howΝtoΝinstallΝorΝremoveΝthisΝRFΝmoduleΝinΝtheΝuser’sΝmanualΝofΝtheΝendΝproductΝwhichΝ integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel. Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: IEC 60950-1:2005 (2nd Edition); Am 1:2009 EN 60950-1:2006+A11:2009+A1:2010+A12:2011 Safety of Information Technology Equipment EN 62311: 2008 / Article 3(1)(a) and Article 2 2006/95/EC) Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz-300 GHz) EN 300 328 V1.8.1: 2012-06 Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating using wide band modulation techniques; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive EN 301 893 V1.7.1: 2012-06 Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive EN 301 489-1 V1.9.2: 2011 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements EN 301 489-17 V2.2.1 2012 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment; Part 17: Specific conditions for Broadband Data Transmission Systems In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. ČeskyΝ [Czech] Dansk [Danish] [Jméno výrobce] tímtoΝprohlašuje,ΝžeΝtentoΝ[typ zařízení] jeΝveΝshoděΝseΝzákladnímiΝ požadavkyΝaΝdalšímiΝpříslušnýmiΝustanovenímiΝsměrniceΝ1λλλ/5/ES. Undertegnede [fabrikantens navn] erklærer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian] Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish] Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. ζζηνδεήΝ [Greek] Μ ΝΣΗΝΝΠΑΡΟΤΑ [name of manufacturer] ΗΛΩΝ ΙΝΟΣΙ [type of equipment] ΤΜΜΟΡΦΩΝ ΣΑΙΝΠΡΟΝΣΙΝΟΤΙΩ ΙΝΑΠΑΙΣΗ ΙΝΚΑΙΝΣΙΝΛΟΙΠ ΝΧ ΣΙΚ Ν ΙΑΣΑΞ ΙΝΣΗΝΟ ΗΓΙΑΝ1λλλ/5/ Κ. Français [French] Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian] Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] ArΝšoΝ[name of manufacturer / izgatavotāja nosaukums] deklarē,ΝkaΝ[type of equipment / iekārtas tips] atbilstΝDirektīvasΝ1λλλ/5/EKΝbūtiskajāmΝprasībāmΝunΝcitiemΝarΝtoΝ saistītajiemΝnoteikumiem. LietuviųΝ [Lithuanian] Nederland s [Dutch] ŠiuoΝ[manufacturer name] deklaruoja,ΝkadΝšis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma [Maltese] mal-ħtiġijietΝessenzjaliΝuΝmaΝprovvedimentiΝoħrajnΝrelevantiΝliΝhemmΝfid-Dirrettiva 1999/5/EC. Magyar [Hungarian] Polski [Polish] Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Niniejszym [nazwa producenta] oświadcza,ΝżeΝ[nazwa wyrobu] jest zgodny z zasadniczymiΝwymogamiΝorazΝpozostałymiΝstosownymiΝpostanowieniamiΝDyrektywyΝ 1999/5/EC. Português [Portuguese] Slovensko [Slovenian] Slovensky [Slovak] Suomi [Finnish] [Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. [Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimiΝrelevantnimiΝdoločili direktive 1999/5/ES. [Meno výrobcu] týmtoΝvyhlasuje,ΝžeΝ[typ zariadenia] spĺňaΝzákladnéΝpožiadavkyΝaΝvšetkyΝ príslušnéΝustanoveniaΝSmerniceΝ1λλλ/5/ES. [Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Taiwan 警語 第十二條→經型式認證合格之低 率射頻電機,非經許 自變更頻率 大 率或變更原設計之特性及 能 ,公司,商 或使用者均不得擅 第十四條→低 率射頻電機之使用不得影響飛航安 及 擾合法通信;經發現有 擾現象 時,應立即停用,並改善至無 擾時方得繼續使用 前項合法通信,指依電信法規定作業之無線電通信 低 率射頻電機須忍 合法通信或工 業 科學及醫療用電波輻射性電機設備之 擾 無線傳輸設備 (UNII) 在 5.25-5.35 秭赫頻帶 操作之無線資訊傳輸設備,限於室 無線資訊傳輸設備忍 合法通信之 擾且不得 俟無 擾之 ,始得繼續使用 (4.7.6) 使用 擾合法通信;如造成 (4.7.5) 擾,應立即停用, 無線資訊傳設備的製造廠商應確保頻率穩定性,如依製造廠商使用手冊上所述正常操作, 發射的信 應維持於操作頻帶中 (4.7.7) Note: 1. 本模組於 上標示 本產品 得認證後將依規定於模組本體標示審驗合格標籤 2. 系統廠商應於 含射頻模組: CCXXxxYYyyyZzW 10 字樣. Table of Contents 1. INTRODUCTION 12 2. DRIVER/UTILITY INSTALLATION / UNINSTALLATION 12 3. CONNECTING TO AN EXISTING NETWORK 12 4. MODIFYING A WIRELESS NETWORK 13 4.1 MODIFYING GENERAL SETTINGS ............................................................................................ 13 4.2 MODIFYING SECURITY SETTINGS ............................................................................................ 14 5. ANTENNA INFORMATION 15 11 1. Introduction Thank you for purchasing the 802.11 a/b/g/n USB Wireless LAN Adaptor that provides the easiest way to wireless networking. This User Manual contains detailed instructions in the operation of this product. Please keep this manual for future reference. System Requirements - 128 MB of RAM or later (recommended) - 300 MHz processor or higher 2. Driver/Utility Installation The driver should have been installed before the TV is shipped from the manufacturer. You can start using its network function without installing driver or utility. 3. Connecting to an Existing Network 1. Use the remote control that came with your TV to access the network configuration settings page. 2. Select the scanning wireless network function. The system starts to scan for available network. On this list, click Refresh to refresh the list at any time 3. Select the network you want to connect to. 4. If the chosen network has security enabled, you will have to setup corresponding security parameter. Contact the network manager for the correct settings. Select the security type and fill in required parameters. The options include the following: WPA/WPA2/CCKM WPA/WPA2 Passphrase 802.1x Pre-Shared Key (Static WEP) None 12 4. Modifying a Wireless Network 4.1 Modifying General Settings 1. Use the remote control that came with your TV to access the network configuration settings page. 2. From the profile list, select one profile and choose the modify function. 3. Modify the settings below for your network. Profile Name Identifies the configuration wireless network profile. This name must be unique. Profile names are not case sensitive. Client Name Identifies the client machine. Use this profile for Access Point mode Configures station to operate in Access Point mode. Network Names (SSIDs) The IEEE 802.11 wireless network name. This field has a maximum limit of 32 characters. Configure up to three SSIDs (SSID1, SSID2, and SSID3). 13 4.2 Modifying Security Settings 1. Use the remote control that came with your TV to access the network configuration settings page. 2. Select a security option of this wireless network. This product provides security options below. Contact your wireless network administrator for choosing a correct option. WPA/WPA2/CCKM WPA/WPA2 Passphrase 802.1x Pre-Shared Key (Static WEP) None WPA/WPA2 WPA/WPA2 Passphrase 802.1x Enables the use of Wi-Fi Protected Access (WPA). Choosing WPA/WPA2 opens the WPA/WPA2 EAP drop-down menu. The options include: EAP-FAST EAP-TLS EAP-TTLS EAP-SIM PEAP (EAP-GTC) PEAP (EAP-MSCHAP V2) LEAP Enables WPA/WPA2 Passphrase security. Click on the Configure button and fill in the WPA/WPA2 Passphrase. Enables 802.1x security. This option requires IT administration. Choosing 802.1x opens the 802.1x EAP type drop-down menu. The options include: Pre-Shared Key (Static WEP) EAP-FAST EAP-TLS EAP-TTLS EAP-SIM PEAP (EAP-GTC) PEAP (EAP-MSCHAP V2) LEAP Enables the use of pre-shared keys that are defined on both the access point and the station. To define pre-shared encryption keys, choose the Pre-Shared Key radio button and click the Configure button to fill in the Define Pre-Shared Keys window. 14 None No security (not recommended). Allow Association to Mixed Cells Check this check box if the access point with which the client adapter is to associate has WEP set to Optional and WEP is enabled on the client adapter. Otherwise, the client is unable to establish a connection with the access point. Check this check box and enter the number of seconds (up to 300) after which the authentication process times out when trying to find the domain controller. Entering zero is like unchecking this check box, which means no time limit is imposed for finding the domain controller. Note: The authentication process times out whenever the authentication timer times out or the time for finding the domain controller is reached. Limit Time for Finding Domain Controller To Group Policy Delay Specify how much time elapses before the Windows logon process starts group policy. Group policy is a Windows feature used by administrators to specify configuration options for groups of users. The objective is to delay the start of Group Policy until wireless network authentication occurs. Valid ranges are from 0 to 65535 seconds. The value that you set goes into effect after you reboot your computer with this profile set as the active profile. This drop-down menu is active only if you chose EAP-based authentication. 5. Antenna Information Antenna Model Peak gain ( dBi ) Type Connector 2400~2483.5MHz 5150~5250MHz 5250~5350MHz 5470~5725MHz 5725~5850MHz ANT0 (Left) Printed NA 0.4 2.38 1.53 0.61 1.76 ANT1 (Right) Printed NA 4.24 0.73 0.62 1.19 0.93 15
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V4.4 (128-bit) User Access : Print, Extract Author : Vicky Lin Create Date : 2014:10:24 14:48:19+08:00 Modify Date : 2014:10:24 16:06:33+08:00 Language : zh-TW Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03 Format : application/pdf Creator : Vicky Lin Title : WLAN a+b+g Cardbus Adapter Creator Tool : Microsoft® Word 2010 Metadata Date : 2014:10:24 16:06:33+08:00 Producer : Microsoft® Word 2010 Document ID : uuid:e10f74af-cb2d-4b88-9cd6-1d5beea863e6 Instance ID : uuid:8add4ba7-effa-416a-829c-c465157ef24d Page Count : 16EXIF Metadata provided by EXIF.tools