Wistron NeWeb USB400 WLAN USB Adapter User Manual ATCB Comments 02022003

Download:
Mirror Download [FCC.gov]
Document ID	303416
Application ID	Lhj2oxhUEwvij5nPkToAqw==
Document Description	ATCB Comments 02022003
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	2.02kB (25244 bits)
Date Submitted	2003-02-17 00:00:00
Date Available	2003-02-17 00:00:00
Creation Date	2003-02-02 05:39:40
Producing Software	Acrobat PDFWriter 5.0 for Windows NT
Document Lastmod	0000-00-00 00:00:00
Document Title	ATCB Comments 02022003.doc
Document Creator	ATCB Comments 02022003 - Microsoft Word
Document Author:	William Graff

American Telecommunications Certification Body Inc.
6731 Whittier Ave, McLean, VA 22101
February 2, 2003
RE:
Winston Ne Web
FCC ID:
NKRUSB400
I have a few comments on this Application.
1.) In the future, please segregate photographs into Externaland Internal exhibits.
2.) Although there are two oscillators listed on the block diagram, the diagram seems to not comply with the
provisions of 2.1033(a)(5) where the signal path and frequency shall be listed at each block. Please
review.
3.) Two manuals were uploaded. Which one should be used for review? I examined the most recent upload
according to the date the files was created on our server. That one has references to 20cm separation
distance between the user and device. This is not appropriate when a SAR report is presented.
4.) The Schematics reference an “Optional Populated” section. This is not appropriate. Only testing
performed with and without the optional components could be accepted by the Commission for filing
under a single FCC ID, or filing as a fully populated device only.
5.) The SAR report in Section 2.1 references an RF Pout of 87.09mW, but later in Section 3 references
30.7mW. Which is correct? Please review and correct as needed.
6.) In the SAR report, I am concerned with the interference of the lid in Mode 1. Please demonstrate this is
the “worst case” position. In other words, please provide evidence that Mode 1 with the LCD lid of
notebook computer perpendicular to phantom is not “worst case” relative to LCD lid parallel to phantom.
7.) Although listed elsewhere in the SAR report, it would be helpful to identify the test platform by make and
model on each “Mode” photograph.
8.) The Mode Two plots in the SAR report appear strange – especially when using the scale supplied on the
right hand side of each plot. Are you showing the highest SAR occurred in fields around the EUT, and not
centered on the EUT? Please confirm.
9.) The Test Setup photos are difficult to use. Can you please supply a close up showing where the EUT was
positioned in the setup?
10.) The Test Report does not provide any graphical presentations (plots) for any of the 15.247 parameters.
This will not be acceptable. Please review and supply at minimum Occupied Bandwidth, Spectral Power
Density, Band Edge (preferably both radiated and conducted), and 6dB Bandwidth. A plot of the
Powerline Conducted Emissions 15.207 is also preferred.
11.) Please show how label identified in Appendix 9 of Test Report will be affixed to EUT. This does not seem
to match the Label information provided in the Label and Location exhibit to AmericanTCB.
William H. Graff
President and Examining Engineer
mailto: whgraff@AmericanTCB.com
The items indicated above must be submitted before processing can continue on the above referenced
application.
Failure to provide the requested information may result in application termination.
Correspondence should be considered part of the permanent submission and may be viewed from the
Internet after a Grant of Equipment Authorization is issued.
l Page 2
February 2, 2003
Please do not respond to this correspondence using the email reply button. In order for your response to be
processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also,
please note that partial responses increase processing time and should not be submitted.
Any questions about the content of this correspondence should be directed to the sender.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 2
Creator                         : ATCB Comments 02022003 - Microsoft Word
Create Date                     : 2003:02:02 05:39:40
Title                           : ATCB Comments 02022003.doc
Author                          : William Graff
Producer                        : Acrobat PDFWriter 5.0 for Windows NT

EXIF Metadata provided by EXIF.tools